PROPOINT 8977084 Le manuel du propriétaire

Marque: PROPOINT

Modèle: 8977084

Catégorie: Système de soudage

Taper: Le manuel du propriétaire

V1.1 8977084

Please read and understand all instructions before use. Retain this manual for future reference.

WELDING MASK KIT



TRUBLU LOPRO

8977084 TRUBLU LoPro Welding Mask Kit V1.1

2 For technical questions call 1-800-665-8685

SPECIFICATIONS

Viewing Area 4.33 x 1.57 in.

Lens Shade Digital 5 to 9 / 9 to 13

Reaction Time

0.08 millisecond

Optical Classification

1/1/1/2

Headgear Adjustable ratcheting type

Grind Mode

Yes

ADF Controls

Digital

Number of Arc Sensors 2

Power Source

Battery

Battery Type

CR2450

Viewing Area

4.33 x 1.57 in.

Operating Temperature

-10 to 65°C (14 to 149°F)

HAZARD DEFINITIONS

Please familiarize yourself with the hazard notices found in this manual. A

notice is an alert that there is a possibility of property damage, injury or

death if certain instructions are not followed.

DANGER! This notice indicates an immediate and specific hazard that

will result in severe personal injury or death if the proper

precautions are not taken.

WARNING! This notice indicates a specific hazard or unsafe practice that

could result in severe personal injury or death if the proper

precautions are not taken.

CAUTION! This notice indicates a potentially hazardous situation that may

result in minor or moderate injury if proper practices are not

taken.

NOTICE! This notice indicates that a specific hazard or unsafe practice

will result in equipment or property damage, but not

personal injury.

V1.1 TRUBLU LoPro Welding Mask Kit 8977084

Visit www.princessauto.com for more information 3

INTRODUCTION

The TRUBLU LoPro Welding Mask provides 5 to 13 shade protection for

your eyes while the faceplate stops welding spatters and ultraviolet and

infrared radiation. The grind function can be activated or deactivated

without removing the goggles.

There is room under the welding mask to fit a standard half-welding mask

respirator. The faceplate can be removed.

SAFETY

WARNING! Read and understand all instructions before using this

tool. The operator must follow basic precautions to reduce the risk

of personal injury and/or damage to the equipment.

Keep this manual for safety warnings, precautions, operating or inspection

and maintenance instructions.

WORK AREA

1. Operate in a safe work environment. Keep your work area clean, well-

lit and free of distractions. Place lights so you are not working in a

shadow.

2. Keep anyone not wearing the appropriate safety equipment away

from the work area.

3. Store tools properly in a safe and dry location. Keep tools out of the

reach of children.

PERSONAL SAFETY

WARNING! Wear personal protective equipment approved by the

Canadian Standards Association (CSA) or American National

Standards Institute (ANSI).

1. Wear gloves that provide protection based on the work materials or

to reduce the effects of tool vibration.

2. Wear protective clothing designed for the work environment and

tool.

3. Control the tool, personal movement and the work environment to

avoid personal injury or damage to the tool.

4. Do not operate any tool when tired or under the influence of drugs,

alcohol or medications.

8977084 TRUBLU LoPro Welding Mask Kit V1.1

4 For technical questions call 1-800-665-8685

SPECIFIC SAFETY PRECAUTIONS

WARNING! DO NOT let comfort or familiarity with product (gained

from repeated use) replace strict adherence to the tool safety rules.

If you use this tool unsafely or incorrectly, you can suffer serious

personal injury.

WARNING! The welding mask does not protect against severe

impact hazards, explosions or corrosive liquids. Machine guards

or eye splash protection must be used when these hazards are

present.

WARNING! Using filter forms from any other manufacturer’s welding

mask can seriously impaired the protection provided and may result

in serious personal injury.

1. Use the correct tool for the job. This welding mask was designed for a

specific function. Do not modify or alter this welding mask or use it for

an unintended purpose.

2. Do not use the tool if any parts are damaged, broken or misplaced.

Repair or replace the parts.

3. This welding mask is not recommended for overhead welding

applications, laser welding or laser cutting applications.

4. In the event of electronic failure, the filter remains dark at Shade 15

to protect against UV and IR radiation.

5. Use the auto-darkening welding filter with inner and outer cover

lenses. Never open or tamper with the filter cartridge.

6. Ensure the front cover lens is mounted before use. Remove the

protective film.

7. Ensure that the lens is clean and there is no dirt or spatter covering

the four sensors at the front of the filter cartridge.

8. Inspect all parts for signs of wear or damage. Any scratched or

cracked parts should be replaced prior to use.

9. Never place the welding mask on a hot surface.

10. Arc rays can burn both eyes and skin. Arc welding produces intense

visible and invisible (ultraviolet and infrared) rays. Wear a welding

mask fitted with the proper shade to protect your face and eyes

when welding or watching.

11. Check whether welding or grinding mode is chosen before use.

V1.1 TRUBLU LoPro Welding Mask Kit 8977084

Visit www.princessauto.com for more information 5

12. The reaction of the filter’s liquid crystal will be slower if the ambient

temperature is low, but it will not affect protective functions.

13. Replace the protective lenses immediately if broken or scratched. The

damage will obscure vision and reduce the filter’s protective

performance.

14. The welding hood included in this kit is flame-retardant. This welding

hood does not provide protection against molten metals.

UNPACKING

WARNING! Do not operate the tool if any part is missing. Replace

the missing part before operating. Failure to do so could result in

a malfunction and personal injury.

Remove the parts and accessories from the packaging and inspect for

damage.

IDENTIFICATION KEY

A Shell

B Outer Lens

C Auto Darkening Goggles

D Inner Lens

E Silicone Padding

F Plastic headband

G Elastic Headband

H Bag

I Welding Hood (May differ from

illustration)

J LED Light

DISPLAY ICONS

K Battery Status

L WELD Mode

M Shade 5-9

N Shade 9-13

O Sensitivity (1 to 5)

P Delay (1 to 5)

Q Shade Setting

R CUT Mode

S GRIND Mode

Fig. 1

Fig. 2

8977084 TRUBLU LoPro Welding Mask Kit V1.1

6 For technical questions call 1-800-665-8685

ASSEMBLY & INSTALLATION

Letter references in parenthesis (A) refer to the included Identification Key.

The welding mask is preassembled. Remove the protective film from both

lenses before use.

SWITCHING HEADBANDS

The welding mask has two headbands: plastic (F) and elastic (G).

Switch out the headbands by pushing on

the headband’s lock catch until it pops off.

Repeat on the other side.

Push the lock catch against the locks on

each side of the goggles (Fig. 3) until they

snap into place.

ADJUST THE WELDING MASK FIT (PLASTIC

HEADBAND)

The headband should be adjusted both in diameter and height.

1. Adjust the headband diameter with the adjusting knob on the headband.

Twist clockwise to tighten and counterclockwise to loosen.

2. Adjust the headband height by releasing the segmental positioning plate

and changing the top strap hole.

ATTACH THE LED LIGHT

1. Place the light’s base in front of the face plate’s bracket.

2. Align the bracket’s tabs with the base’s slots.

3. Push the light backwards until it touches the bracket’s backstop.

4. Remove the light by pulling it forward until it is free of the bracket.

OPERATION

WARNING! Do not weld if the orange light inside the goggles is

flashing. This is the Grind mode indicator and you can suffer eye

or retina damage, as the lens will not darken when the welding arc

forms.

Fig. 3

V1.1 TRUBLU LoPro Welding Mask Kit 8977084

Visit www.princessauto.com for more information 7

BEFORE WELDING

1. Ensure that the internal and external protective films are removed from

the lenses.

2. Check that the batteries have sufficient power to operate the welding

mask.

3. Check that the arc sensors are clean and not blocked by dust or debris.

4. Check for head band tightness before each use.

WELDING MASK SETTINGS

The control panel is on the left side of the googles, with the exception of

the GRIND button, which is on the right side of the goggles.

1. Press the MODE button to cycle through the four modes: Weld (5-9),

Weld (9-13), Grind and Cut. The icons and numbers shown on the LCD

screen depends on which mode is selected.

2. Once a mode is selected, press the SHADE, SENS. or DELAY button

once to activate that setting. The icon will begin flashing.

3. Continue to press the button to cycle through the setting levels.

4. The icon will stop flashing after a few seconds, indicating the setting

is complete.

SHADE NUMBER SELECTION

1. Determine what DIN Shade number is

needed for the task (see Appendix A).

2. Select to the weld mode that has the

correct range, either Shade 9-5 (M) or

9-13 (N). The weld icon (L) will also be

visible (Fig. 4).

3. Press the SHADE button once to

activate the setting and then press it

again until the correct shade number

(Q) is displayed. It will only cycle

through the number in the selected

range.

Fig. 4

Fig. 5

8977084 TRUBLU LoPro Welding Mask Kit V1.1

8 For technical questions call 1-800-665-8685

DELAY TIME

Delay time refers to the time the cartridge filter is set to change from the

dark to bright state after welding stops. The delay can be adjusted up to a

0.9 second delay.

A short delay is suitable for spot or short welds. This allows you to track

the progress of the weld. A long delay is better suited for heavy welding

when there is an afterglow.

1. Select the weld mode, then press the DELAY button until the delay

icon (P) flashes.

2. Each press of the DELAY button will add a bar to the delay time. Each

bar increases the delay by 0.2 seconds starting from 0.1 to 0.9

seconds.

SENSITIVITY

Sensitivity is the degree the lens darkens based on the arc brightness and the

amount of light in the work area. This setting can be manually adjusted when

in welding mode.

1. Select the weld mode, then press the SENS. button until the

sensitivity icon (O) flashes.

2. Each press of the SENS. button will add a bar to the sensitivity. Each

bar increases the sensitivity by 0.2 seconds starting from 0.1 to 0.9

seconds.

Low Setting (0.1) Suitable for high amperage welding and

welding in areas with high levels of natural

sunlight.

Medium Setting (0.5) Suitable for most indoors and outdoors

welding.

High Setting (0.9) Suitable for low amperage welding and welding

in areas with low light conditions, especially for

low amperage argon-arc welding.

CUT MODE

WARNING! Do not use these goggles if the cutting task requires a

DIN shade higher than Shade 9. A bright cutting arc can cause

eye or retina damage if the Shade protection is inadequate.

V1.1 TRUBLU LoPro Welding Mask Kit 8977084

Visit www.princessauto.com for more information 9

1. Determine what DIN Shade number is

needed for the task.

2. Press the MODE button until the Cut

icon (R) appears in the LCD. The DIN

Shade 5-9 icon (M) will also appear.

3. Press the SHADE button until the icon

(Q) is flashing. Press the button to select the DIN shade.

GRINDING MODE

You can also use the welding mask to protect your face during grinding. This

will prevent the filter cartridge from darkening when bright sparks are

created.

1. Press the GRIND button on the right

side of the goggles for 2 seconds to

activate grind mode.

2. The grinding icon (S) will appear on the

LCD.

3. An orange light inside the goggles will flash when in grind mode. You

cannot adjust the shade number.

4. Press the GRIND button for 2 seconds to switch off GRIND mode.

BATTERY ICON

The battery icon (K) indicates the power charge available. Change the

batteries when down to a single bar that flashes (see Maintenance –

Battery Replacement).

WARNING! Failure to change a low battery may result in exposure

to UV/IR radiation and blinding arc light. A low battery may

compromise the delay timing and shade accuracy.

SLEEP MODE

The welding mask will enter sleep mode after 30 minutes of inactivity to

conserve the battery power. Push any button to activate the goggles.

The last shade setting in weld mode will be retained in memory. Cut and

Grind settings are not saved to memory.

LED LIGHT

1. Push the power button on top to activate the light.

2. Loosen a side knob slightly.

Fig. 6

Fig. 7

8977084 TRUBLU LoPro Welding Mask Kit V1.1

10 For technical questions call 1-800-665-8685

3. Adjust the light to the desired position.

4. Tighten the side knob to secure.

5. Turn the power off until ready for use.

CARE & MAINTENANCE

1. Maintain the tool with care. A tool in good condition is efficient,

easier to control and will have fewer problems.

2. Inspect the tool components periodically. Repair or replace damaged

or worn components. Only use identical replacement parts when

servicing.

3. Maintain the tool’s labels and name plates. These carry important

information. If unreadable or missing, contact Princess Auto Ltd. for

replacements.

WARNING! Only qualified service personnel should repair the tool.

An improperly repaired tool may present a hazard to the user

and/or others.

CHANGE EXTERNAL AND INTERNAL LENS

The external and internal lenses will wear out and need replacement after

a period of use due to exposure to the heat, fumes and particulate matter

generated during welding.

INTERNAL LENS

1. Grip the inner lens at the top (Fig. 8) at

the molded indent and pull it out. The

lens will flex and slide out of the side

hooks.

2. Position the new lens into the left hook

and push and bend the lens towards

you (Fig. 9).

3. Slip the right side of the lens under the

right hook and release the lens.

4. Gently push the lens into the goggles to

seat it in the opening.

Fig. 8

Fig. 9

V1.1 TRUBLU LoPro Welding Mask Kit 8977084

Visit www.princessauto.com for more information 11

EXTERNAL LENS

1. Grip the small tab on the bottom of the

outer lens (Fig. 10) and pull it out. The

lens will flex and slide out of the side

hooks.

2. Position the new lens into the left hook

by aligning the lens tab with the hook

opening (Fig. 11).

3. Bend the lens towards yourself and slip the

right side of the lens under the right hook,

aligning the tab and release the lens.

4. Gently push the lens into the goggles to

seat it in the opening.

REPLACE THE SILICONE PADDING.

The silicone padding is replaceable if it is torn or

damaged. The padding is held in place by tabs.

1. Pull the sides towards the middle to

disconnect the side tabs (Fig. 12).

2. Grip the padding by the upper left and right

corner and pull it from the goggle’s body.

3. Position the new padding onto the goggle’s

body. Gently press down on the left and

right side of the padding. Wiggle the

padding around until the side tabs lock into

place (Fig. 13).

4. Work your fingers around the inner edge of

the padding to force the tabs to lock into

place.

5. Gently pull along the padding edge to check

if it is secure. Repeat steps 3 and 4 if needed until the padding is

locked into place.

Fig. 10

Fig. 11

Fig. 12

Fig. 13

8977084 TRUBLU LoPro Welding Mask Kit V1.1

12 For technical questions call 1-800-665-8685

BATTERY REPLACEMENT

1. Remove the small cover

screw on the inner right side

of the goggles (Fig. 13), then

slide the cover off the

battery holder.

2. Remove the old battery and

replace with a new CR2450

lithium battery. Check that the battery’s polarity is correct.

3. Reinstall the cover.

REMOVING AND REINSTALLING THE

FACEPLATE

The faceplate is held in place by a lock and tab system on either side of the

goggles, just behind the control panel and grind button.

1. Press the left tab outward to free

it from the lock and hold it there.

2. At the same time, hold the onto

the faceplate and press against

the goggles on the same side. The

faceplate will pop off.

3. Repeat steps 1 and 2 on the other

side. Set the faceplate aside once

it is free.

4. Reattach the faceplate by aligning the locks and tabs on either side of

the goggles and faceplate.

5. Push the goggles down into place until the tabs catch onto the locks.

Check that the connection is firm on each side.

6. Clean the lenses of fingerprints after removing or installing the mask.

CLEANING

Clean the lens, welding mask shell and headband with a soft cotton cloth

and mild soap. Replace the headband when required.

Fig. 14

Fig. 15

V1.1 TRUBLU LoPro Welding Mask Kit 8977084

Visit www.princessauto.com for more information 13

DISPOSAL

Recycle a tool damaged beyond repair at the appropriate facility.

Contact your local municipality for a list of disposal facilities or by-laws for

electronic devices, batteries, oil or other toxic liquids.

TROUBLESHOOTING

Visit a Princess Auto Ltd. location for a solution if the tool does not

function properly or parts are missing. If unable to do so, have a qualified

technician service the tool.

PROBLEM(S)

POSSIBLE CAUSE(S)

SUGGESTED SOLUTION(S)

Irregular

Darkening.

Headgear is set unevenly so the

distance between the eyes and

the lens is different from the

left to the right side.

Adjust headgear so distance is

equal between the lens and

both eyes.

Filter does not

darken or

flickers.

1. Front cover lens is dirty or

smoke covered.

2. Arc sensors may be dirty.

3. Welding current is too low.

4. Battery voltage is too low.

1. Clean or replace external

lens.

2. Remove external lens and

wipe the photo sensors

clean with soft lint free

cloth.

3. Adjust filter sensitivity to

the maximum.

4. Replace batteries.

Poor vision. 1. Check the clear covers

lenses and the electronic

filter lens for dirt or grime.

2. Protective film was not

removed.

3. Ambient light is not

sufficient to see.

4. Shade Number is not set

correctly.

1. Clean cover lenses and

electric filter lens.

2. Remove protective film.

3. Adjust the work area

lighting.

4. Reset Shade number.

Welding Cap

slips.

The headband is not properly

adjusted.

Adjust the headgear tightness

adjusting knob for a tighter fit.

8977084 TRUBLU LoPro Welding Mask Kit V1.1

14 For technical questions call 1-800-665-8685

APPENDIX A

V1.1 TRUBLU LoPro Welding Mask Kit 8977084

Visit www.princessauto.com for more information 15

8977084 TRUBLU LoPro Welding Mask Kit V1.1

16 For technical questions call 1-800-665-8685

V1,1 8977084

Vous devez lire et comprendre toutes les instructions avant d'utiliser l'appareil. Conservez ce

manuel afin de pouvoir le consulter plus tard.

TROUSSE POUR CASQUE

DE SOUDAGE



TRUBLU LOPRO

8977084 Trousse pour casque de soudage TRUBLU LoPro V1,1

2 En cas de questions techniques, appelez le 1-800-665-8685

SPÉCIFICATIONS

Zone de visibilité

4,33 x 1,57 po

Teinte de lentille

Numérique 5 à 9 / 9 à 13

Temps de réaction

0,08 milliseconde

Classification optique

1/1/1/2

Couvre-chef

Type à cliquet réglable

Mode de meulage

Oui

Commandes du filtre à

assombrissement automatique

Numérique

Nombre de capteurs d’arc

Source d’énergie

Pile

Type de batterie

CR2450

Zone de visibilité

4,33 x 1,57 po

Température de fonctionnement

-10 à 65 °C (14 à 149 °F)

DÉFINITIONS DE DANGER

Veuillez-vous familiariser avec les avis de danger qui sont présentés dans ce

manuel. Un avis est une alerte indiquant qu'il existe un risque de dommage à

la propriété, de blessure ou de décès si on ne respecte pas certaines

instructions.

DANGER ! Cet avis indique un risque immédiat et particulier qui

entraînera des blessures corporelles graves ou même

la mort si on omet de prendre les précautions

nécessaires.

AVERTISSEMENT ! Cet avis indique un risque particulier ou une pratique

non sécuritaire qui pourrait entraîner des blessures

corporelles graves ou même la mort si on omet de

prendre les précautions nécessaires.

ATTENTION ! Cet avis indique une situation possiblement dangereuse

qui peut entraîner des blessures mineures ou modérées

si on ne procède pas de la façon recommandée.

AVIS ! Cet avis indique un risque particulier ou une pratique

non sécuritaire qui entraînera des dommages au niveau

de l'équipement ou des biens, mais non des blessures

corporelles.

V1,1 Trousse pour casque de soudage TRUBLU LoPro 8977084

Visitez www.princessauto.com pour plus d'informations 3

INTRODUCTION

Le casque de soudage TRUBLU LoPro offre une protection de teintes 5 à

13, tandis que la visière protège contre les projections de soudure, les

rayons ultraviolets et le rayonnement infrarouge. La fonction de meulage

peut être activée ou désactivée sans retirer les lunettes de sécurité.

Un espace prévu sous le casque de soudage permet de raccorder un demi-

masque respiratoire. La visière peut être retirée.

SÉCURITÉ

AVERTISSEMENT ! Veuillez lire et comprendre toutes les

instructions avant d'utiliser cet outil. L'utilisateur doit respecter les

précautions de base lorsqu'il utilise cet outil afin de réduire le

risque de blessure ou de dommage à l'équipement.

Conservez ce manuel qui contient les avertissements de sécurité, les

précautions, les instructions de fonctionnement ou d'inspection et

d'entretien.

AIRE DE TRAVAIL

1. Travaillez dans un environnement de travail sécuritaire. Gardez votre

aire de travail propre, bien éclairée et exempte de toute distraction.

Placez les lampes de façon à ne pas travailler dans l’ombre.

2. Assurez-vous que les personnes qui ne portent pas l'équipement de

sécurité approprié ne se trouvent pas à proximité de l'aire de travail.

3. Rangez les outils correctement dans un lieu sécurisé et sec. Gardez

les outils hors de la portée des enfants.

SÉCURITÉ PERSONNELLE

AVERTISSEMENT ! Portez de l'équipement de protection personnelle

homologué par l'Association canadienne de normalisation (CSA) ou

l'American National Standards Institute (ANSI).

1. Portez des gants qui protègent en fonction des matériaux de travail et

pour réduire les effets des vibrations de l'outil.

2. Portez des vêtements de protection conçus pour l'environnement de

travail et pour l'outil.

3. Gardez le contrôle de l'outil, de vos mouvements et de l'environnement

de travail pour éviter les blessures ou le bris de l'outil.

8977084 Trousse pour casque de soudage TRUBLU LoPro V1,1

4 En cas de questions techniques, appelez le 1-800-665-8685

4. N'utilisez pas l'outil si vous êtes fatigué ou sous l'effet de drogues,

d'alcool ou de médicaments.

CONSIGNES DE SÉCURITÉ SPÉCIFIQUES

AVERTISSEMENT ! Ne permettez PAS au confort ou à votre

familiarisation avec l'outil (obtenus après un emploi répété) de se

substituer à une adhésion stricte aux règles de sécurité de l'outil.

Si vous utilisez cet outil de façon dangereuse ou incorrecte, vous

pouvez subir des blessures corporelles graves.

AVERTISSEMENT ! Le masque de soudeur à assombrissement

automatique ne protège pas contre les impacts élevés, les

explosions ou les liquides corrosifs. Utilisez un protecteur

sur l’appareil ou protégez-vous les yeux lorsque ces dangers sont

présents.

AVERTISSEMENT ! L’utilisation d’un filtre provenant du masque

d’un autre fabricant peut compromettre sérieusement la protection

offerte et entraîner des blessures graves.

1. Utilisez le bon masque de soudeur pour la tâche à effectuer. Cet masque

de soudeur a été conçu pour une utilisation spécifique. Évitez de

modifier ou d’altérer cet masque de soudeur ou de l’utiliser à une fin

autre que celle pour laquelle il a été conçu.

2. N’utilisez pas l’outil si des pièces présentent des dommages ou sont

déplacées. Réparez ou remplacez les pièces.

3. Le masque de soudeur à assombrissement automatique n’est pas

recommandé pour les opérations de soudage en hauteur, le soudage

au laser ou le découpage au laser.

4. En cas de panne électronique, le filtre demeure foncé afin de

protéger contre les rayons ultraviolets et infrarouges conformément à

la teinte 15.

5. Utilisez le filtre de soudage à assombrissement automatique avec des

couvre-lentilles internes et externes. N’ouvrez ni ne trafiquez jamais

la cartouche du filtre.

6. Assurez-vous que la lentille de couvercle avant est installée avant de

l’utiliser. Retirez la pellicule protectrice.

7. Assurez-vous que la lentille est propre et qu’aucune saleté ou

éclaboussure ne recouvre les quatre capteurs sur l’avant de la

cartouche du filtre.

La page charge ...

PROPOINT 8977084 Le manuel du propriétaire

Marque: PROPOINT

Modèle: 8977084

Catégorie: Système de soudage

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: PROPOINT 8977084 Owner's manual

PROPOINT 8977084 Le manuel du propriétaire

PROPOINT 8977084 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents