PROPOINT 8819864 Le manuel du propriétaire

Marque: PROPOINT

Modèle: 8819864

Catégorie: Système de soudage

Taper: Le manuel du propriétaire

V1.0 8819864

Please read and understand all instructions before use. Retain this manual

for future reference.

SOLAR AUTO-DARKENING

WELDING HELMET WITH

BLUE LENS TECHNOLOGY

USER MANUAL

8819864 Solar Auto-Darkening Welding Helmet V1.0

With Blue Lens Technology

2 For technical questions call 1-800-665-8685

SPECIFICATIONS

Viewing Area 3.94 X 3.28 in. (100 x 83 mm)

Light State Shade DIN 4

Variable Shade DIN 5 to 9 / 9 to 13

Reaction Time 1/25,000 seconds (0.04 milliseconds)

Delay Control (Dark to Light)

0.1 to 0.9 Seconds (Adjustable)

Sensitivity Low to High (Adjustable)

UV/IR Protection Up to Shade DIN 15 at all times.

Arc Sensors

Power ON/OFF Fully Automatic

Power Supply Solar cells and replaceable CR2450 lithium

batteries

Battery Life 1,000 h

Grind Mode

Yes

Operating Temperature 14° ~ 149°F (-10° to 65°C)

Storage Temperature -4° ~ 185°F (-20° to 85°C)

Compliance ANSI Z87 W4/5-13 and CSA Z94.3 W4/5-13

ADF Controls Internal - Digital

Material Polyamide

Headgear Adjustable Ratcheting Type

Memory function

Yes

SOLAR AUTO-DARKENING

WELDING HELMET WITH

BLUE LENS TECHNOLOGY

V1.0 Solar Auto-Darkening Welding Helmet 8819864

With Blue Lens Technology

Visit www.princessauto.com for more information 3

INTRODUCTION

The Solar Auto-Darkening Welding Helmet incorporates Blue

Lens technology, letting the welder to see the full colour

spectrum with clarity while in the light state. Digital controls

enables the welder to adjust the DIN shade number,

Weld/Grind selection, plus the delay and sensitivity timing. The

user can save the settings in memory up to three times.

SAFETY

WARNING! Read and understand all instructions before using

this tool. The operator must follow basic precautions to reduce

the risk of personal injury and/or damage to the equipment.

Keep this manual for safety warnings, precautions, operating or

inspection and maintenance instructions.

HAZARD DEFINITIONS

Please familiarize yourself with the hazard notices found in this

manual. A notice is an alert that there is a possibility of property

damage, injury or death if certain instructions are not followed.

DANGER! This notice indicates an immediate and specific

hazard that will result in severe personal injury or

death if the proper precautions are not taken.

WARNING! This notice indicates a specific hazard or unsafe

practice that could result in severe personal injury

or death if the proper precautions are not taken.

CAUTION! This notice indicates a potentially hazardous

situation that may result in minor or moderate

injury if proper practices are not taken.

NOTICE! This notice indicates that a specific hazard or unsafe

practice will result in equipment or property

damage, but not personal injury.

8819864 Solar Auto-Darkening Welding Helmet V1.0

With Blue Lens Technology

4 For technical questions call 1-800-665-8685

WORK AREA

1. Operate in a safe work environment. Keep your work area

clean, well lit and free of distractions.

2. Keep anyone not wearing the appropriate safety equipment

away from the work area.

3. Store tools properly in a safe and dry location. Keep tools out

of the reach of children.

PERSONAL SAFETY

WARNING! Wear personal protective equipment approved by

the Canadian Standards Association (CSA) or American

National Standards Institute (ANSI).

1. Always wear impact safety goggles that provide front and

side protection for the eyes.

2. Wear gloves that provide protection based on the work

materials or to reduce the effects of tool vibration.

3. Wear protective clothing designed for the work environment

and tool.

4. Control the tool, personal movement and the work

environment to avoid personal injury or damage to tool.

5. Do not operate any tool when tired or under the influence of

drugs, alcohol or medications.

6. Use the correct tool for the job. This welding helmet was

designed for a specific function. Do not modify or alter this

welding helmet or use it for an unintended purpose.

SPECIFIC SAFETY PRECAUTIONS

WARNING! The Auto-Darkening Welding Helmet does not

protect against severe impact hazards, explosions or corrosive

liquids. Machine guards or eye splash protection must be used

when these hazards are present.

V1.0 Solar Auto-Darkening Welding Helmet 8819864

With Blue Lens Technology

Visit www.princessauto.com for more information 5

WARNING! Using filter forms from any other manufacturer’s

helmet can seriously impaired the protection provided and may

result in serious personal injury.

1. Use the correct tool for the job. This tool was designed for a

specific function. Do not modify or alter this tool or use it for

an unintended purpose.

2. This auto-darkening welding helmet is not recommended

for overhead welding applications, laser welding or laser

cutting applications.

3. This welding helmet is not suitable to laser welding and oxy-

acetylene welding.

4. In the event of electronic failure, the filter remains dark at

Shade 15 to protect against UV and IR radiation.

5. Use the auto-darkening welding filter with inner and outer

cover lenses. Never open or tamper with the filter cartridge.

6. Ensure the front cover lens is mounted before use. Remove

the protective film.

7. Ensure that the lens is clean and there is no dirt or spatter

covering the four sensors at the front of the filter cartridge.

8. Inspect all parts for signs of wear or damage. Any scratched

or cracked parts should be replaced prior to use.

9. Never place the helmet on a hot surface.

10. Arc rays can burn both eyes and skin. Arc welding produces

intense visible and invisible (ultraviolet and infrared) rays.

Wear a welding helmet fitted with the proper shade to

protect your face and eyes when welding or watching.

11. Check whether welding or grinding mode is chosen

before use.

12. The reaction of the filter’s liquid crystal will be slower if

the ambient temperature is low, but it will not affect

protective functions.

8819864 Solar Auto-Darkening Welding Helmet V1.0

With Blue Lens Technology

6 For technical questions call 1-800-665-8685

13. Replace the protective lenses immediately if broken or

scratched. The damage will obscure vision and reduce the

filter’s protective performance.

UNPACKING

WARNING! Do not operate the tool if any part is missing.

Replace the missing part before operating. Failure to do so

could result in a malfunction and personal injury.

Remove the parts and accessories from the packaging and inspect

for damage. Make sure that all items in the contents are included.

Contents: • Welding Helmet Shell • Internal and External Lenses

• Cartridge Filter • Headgear • Batteries

V1.0 Solar Auto-Darkening Welding Helmet 8819864

With Blue Lens Technology

Visit www.princessauto.com for more information 7

IDENTIFICATION KEY

A Shade Button

B Sensitivity Button

C Weld/Grind Button

D Delay Button

E LCD Screen

F Memory Buttons

G Battery Icon

H Welding Icon

I Grinding Icon

J Sensitivity Range Icon

K Shade DIN Number

L Delay Range Icon

M to O Chosen Memory Slot

P Shade Range 9-13 Selected

Q Shade Range 5-9 Selected

8819864 Solar Auto-Darkening Welding Helmet V1.0

With Blue Lens Technology

8 For technical questions call 1-800-665-8685

ASS EM B LY

The welding helmet is preassembled. Remove the protective film

from both lenses before use.

ADJUST THE WELDING HELMET FIT

The headband should be adjusted both in diameter and height.

The angle between face and helmet should also be adjusted

(recommended 10° to 12°).

1. Adjust the headband diameter with the adjusting knob (#14) on

the headband. Twist clockwise to tighten and counterclockwise

to loosen.

2. Adjust the headband height by releasing the segmental

positioning plate (#18) and changing the top strap hole.

3. Adjust the helmet position on the headband. There are three

slots on the headgear slider (#12). Once the slot is chosen,

tighten the angle adjustment knobs. Make sure the same slot

is chosen for both sides for proper vision.

4. Adjust the helmet to get the desired viewing angle. Once the

angle is correct, tighten the two angle adjustment knobs (#2)

connecting the headband to the helmet shell until snug. The

helmet should still swing up, but it should not drift downward

when in place for welding.

OPERATION

BEFORE WELDING

1. Ensure that the internal and external protective films are

removed from the lenses.

2. Check that the batteries have sufficient power to operate

the helmet.

3. Check that the arc sensors are clean and not blocked by dust

or debris.

4. Check for head band tightness before each use.

V1.0 Solar Auto-Darkening Welding Helmet 8819864

With Blue Lens Technology

Visit www.princessauto.com for more information 9

HELMET SETTINGS

The LCD displays the activity icons and the words Sensitivity,

Shade and Delay at the bottom, along with their accompanying

range icons indicating the selected setting.

Each setting is entered by first pressing a button twice to

activate the selection, then continuing to press the same

button to change the setting number. There are four control

buttons and three memory select buttons.

SHADE NUMBER SELECTION

Activating the shade button (A) will display either the 5-9 (Q)

or 9-13 (P) shade range icon. It will start at the lowest setting.

Each time you press the shade button, the number displayed

(K) will increase by one.

Press the weld/grind button (C) to switch over to the 9-13 range

and press the shade button. Continually pressing it past shade 13

will automatically switch it back to the 5-9 shade range.

Adjust the welding helmet’s Shade Number to match the type

of welding. Consult the Welding Shade Guide (see Appendix A)

to determine the minimum shade for the amperage and

welding method being employed.

DELAY TIME

Delay time refers to the time the cartridge filter is set to

change from the dark to bright state after welding stops. The

delay can be adjusted (L) up to a 0.9 second delay.

The delay is set between 0.1, suitable for spot or short welds to

0.9 seconds, suitable for heavy current welding or when visible

light is produced.

Press the delay button (D) after activation to add a bar to the

Delay LCD range. Each bar increases the delay by 0.2 seconds

starting from 0.1 to 0.9 seconds.

8819864 Solar Auto-Darkening Welding Helmet V1.0

With Blue Lens Technology

10 For technical questions call 1-800-665-8685

SENSITIVITY

Press the sensitivity button (B) twice to activate the selection.

The top sensitivity bar will flash to indicate the highest sensitivity

is selected. Continue to press the sensitivity button to scroll

through settings 1 to 5 (least to most sensitive).

1. Low Setting - suitable for high amperage welding and

welding in areas with high levels of natural sunlight.

2. Medium Setting - suitable for most indoors and outdoors

welding.

3. High Setting - suitable for low amperage welding and

welding in areas with low light conditions, especially for

low amperage argon-arc welding.

GRINDING MODE

You can also use the welding helmet to protect your face during

grinding. This will prevent the filter cartridge from darkening

when bright sparks are created.

Press the weld/grind button (C) twice to activate, then hold the

down until Shade number 4 appears in the LCD. The grinding

icon (I) will appear on the LCD and the weld/grind button LED

will flash red to confirm grind mode is set. You cannot adjust the

shade number and memory save/retrieve functions grind mode.

MEMORY SETTING

Press the memory button (F) and the identical number icon (M,

N, O) will appear. Hold the memory button until it stops

flashing to store the current settings. Existing saved settings

can be overwritten by the same process.

Press a memory button once to retrieve and use the saved setting.

Press any button on the left side to ignore the memory settings.

The general settings are stored when the helmet is shut off. The

general settings remain when the helmet is turned on. These

settings are lost if a saved setting is used.

V1.0 Solar Auto-Darkening Welding Helmet 8819864

With Blue Lens Technology

Visit www.princessauto.com for more information 11

When a general setting is completed, the ADF settings will be

stored for 5 minutes

BATTERY ICON

The battery icon (G) indicates the power charge available.

Change the batteries when down to a single bar (see

Maintenance – Battery Replacement).

WARNING! Failure to change a low battery may result in

exposure to UV/IR radiation and blinding arc light. A low

battery may compromise the delay timing and shade

accuracy.

MAINTENANCE

1. Maintain the tool with care. A tool in good condition is

efficient, easier to control and will have fewer problems.

2. Inspect the tool components periodically. Repair or replace

damaged or worn components.

3. When servicing, use only identical replacement parts. Only

use accessories intended for use with this tool. Replace

damaged parts immediately.

WARNING! Only qualified service personnel should repair the

tool. An improperly repaired tool may present a hazard to the

user and/or others.

CHANGE EXTERNAL AND

INTERNAL LENS

The external and internal lenses will wear out and need

replacement after a period of use due to exposure to the heat,

fumes and particulate matter generated during welding.

1. Remove the cradle lock (#6) and pull the cradle from the

welding helmet.

2. Remove the filter cartridge (#7) from the ADF cradle (#4).

8819864 Solar Auto-Darkening Welding Helmet V1.0

With Blue Lens Technology

12 For technical questions call 1-800-665-8685

3. Remove the inner lens (#11) by sliding it out of the cartridge

(#7). Install the new inner cover lens after the protective

film is removed.

4. Remove the external lens (#3) by pulling the lens from

cradle’s front. Remove the protective film from the new

cover lens and carefully press it into the cradle.

5. Insert the cradle back into the helmet and secure with the

cradle lock.

BATTERY REPLACEMENT

1. Replace the battery by removing the battery holder (#8)

on the cartridge’s bottom corner.

2. Remove the old battery and replace with a new CR2450

lithium battery. Check that the battery’s polarity is correct.

3. Reinstall the cover holder into the ADF.

CLEANING

NOTICE! Do not use alcohol, gasoline or diluents to clean the

filter cartridge. Do not put place the filter cartridge into water

as this will damage the filter.

Clean the lens, helmet shell and headband with a soft cotton cloth

and mild soap. Replace the headband when required.

DISPOSAL

Recycle a tool damaged beyond repair at the appropriate facility.

Contact your local municipality for a list of disposal facilities or

by-laws for electronic devices, batteries, oil or other toxic

liquids.

V1.0 Solar Auto-Darkening Welding Helmet 8819864

With Blue Lens Technology

Visit www.princessauto.com for more information 13

TROUBLESHOOTING

Contact Princess Auto Ltd. for a solution if the tool does not

function properly or parts are missing. If unable to do so, have a

qualified technician service the tool.

PROBLEM(S)

POSSIBLE CAUSE(S)

SUGGESTED SOLUTION(S)

Irregular

Darkening.

Headgear is set unevenly

so the distance between

the eyes and the lens is

different from the left to

the right side.

Adjust headgear so distance

is equal between the lens

and both eyes.

Filter does

not darken or

flickers.

1. Front cover lens is

dirty or smoke

covered.

2. Arc sensors may be

dirty.

3. Welding current is too

low.

4. Battery voltage is too

low.

1. Clean or replace external

lens.

2. Remove external lens and

wipe the photo sensors

clean with soft lint free

cloth.

3. Adjust filter sensitivity to

the maximum.

4. Replace batteries.

Poor vision. 1. Check the clear covers

lenses and the

electronic filter lens

for dirt or grime.

2. Protective film was

not removed.

3. Ambient light is not

sufficient to see.

4. Shade Number is not

set correctly.

1. Clean cover lenses and

electric filter lens.

2. Remove protective film.

3. Adjust the work area

lighting.

4. Reset Shade number.

Welding Cap

slips.

The headband is not

properly adjusted.

Adjust the headgear

tightness adjusting knobs

(#14) for a tighter fit.

8819864 Solar Auto-Darkening Welding Helmet V1.0

With Blue Lens Technology

14 For technical questions call 1-800-665-8685

PARTS BREAKDOWN

PARTS LIST

DESCRIPTION

Shell

Angle Adjustment Knobs

Outer Protection Lens

ADF Cradle

Lens Holder

Cradle Lock

Auto Darkening Filter Cartridge

Battery Holder

Battery

ADF Setting Panel

Inner Protection Lens

Headgear Slider

Headgear Screw, Left

Headgear Tightness Adjusting

Knob

Headgear Band

Headgear Screw, Right

Headgear Nut

Headgear Adjustment Knob

Segmental Positioning Plate

Sweatband

Block Nut

V1.0 Solar Auto-Darkening Welding Helmet 8819864

With Blue Lens Technology

Visit www.princessauto.com for more information 15

APPENDIX A

8819864 Solar Auto-Darkening Welding Helmet V1.0

With Blue Lens Technology

16 For technical questions call 1-800-665-8685

V1,0 8819864

Vous devez lire et comprendre toutes les instructions avant d'utiliser

l'appareil. Conservez ce manuel afin de pouvoir le consulter plus tard.

CASQUE DE SOUDEUR À

ASSOMBRISSEMENT AUTOMATIQUE

SOLAIRE AVEC LA TECHNOLOGIE

DE LENTILLES BLEUES

MANUEL D'UTILISATEUR

8819864 Casque de soudeur à assombrissement automatique solaire V1,0

avec la technologie de lentilles bleues

2 En cas de questions techniques, appelez le 1-800-665-8685

SPÉCIFICATION

Zone de visibilité 100 x 83 mm (3,94 x 2,36 po)

Niveau de teinte légère Teinte DIN 4

Teinte variable DIN 5 à 9 / 9 à 13

Temps de réaction 0,04 millisecondes (1/25 000 secondes)

Commande temporisée

(de sombre à éclairé)

0,1 à 0,9 secondes (réglable)

Sensibilité Basse à haute (Réglable)

Protection UV/IR Jusqu’à un indice de teinte DIN 15 en tout

temps.

Capteurs d'arc 4

Alimentation en marche/arrêt

(ON/OFF)

Entièrement automatique

Source d'énergie

Piles solaires et piles au lithium CR2450

remplaçables

Durée utile de batterie

1 000 h

Mode de meulage

Oui

Température de

fonctionnement -10° à 65°C (14° à 149°F)

Température d'entreposage

-20° à 85°C (-4° à 185°F)

Conformité

ANSI Z87 W4/5-13 et CSA Z94,3 W4/5-13

Commandes du filtre à

assombrissement automatique

Intérieur – numérique

Matériau

Polyamide

Bandeau

Type à cliquet réglable

Fonction de mémorisation

Oui

CASQUE DE SOUDEUR À

ASSOMBRISSEMENT AUTOMATIQUE

SOLAIRE AVEC LA TECHNOLOGIE

DE LENTILLES BLEUES

V1,0 Casque de soudeur à assombrissement automatique solaire 8819864

avec la technologie de lentilles bleues

Visitez www.princessauto.com pour plus d'informations 3

INTRODUCTION

Le casque de soudeur à assombrissement automatique solaire

avec la technologie de lentilles bleues permet au soudeur de voir

clairement le spectre des couleurs complet lorsqu’allumé. Des

commandes numériques permettent au soudeur de régler le

numéro de teinte DIN, le mode de soudure/meulage, la durée du

délai et la sensibilité. L’utilisateur peut sauvegarder jusqu’à trois

réglages en mémoire.

SÉCURITÉ

AVERTISSEMENT ! Veuillez lire et comprendre toutes les

instructions avant d'utiliser cet outil. L'utilisateur doit respecter

les précautions de base lorsqu'il utilise cet outil afin de réduire

le risque de blessure ou de dommage à l'équipement.

Conservez ce manuel qui contient les avertissements de

sécurité, les précautions, les instructions de fonctionnement ou

d'inspection et d'entretien.

DÉFINITIONS DE DANGER

Veuillez-vous familiariser avec les avis de danger qui sont

présentés dans ce manuel. Un avis est une alerte indiquant qu'il

existe un risque de dommage à la propriété, de blessure ou de

décès si on ne respecte pas certaines instructions.

DANGER ! Cet avis indique un risque immédiat et

particulier qui entraînera des blessures

corporelles graves ou même la mort si on

omet de prendre les précautions nécessaires.

AVERTISSEMENT ! Cet avis indique un risque particulier ou une

pratique non sécuritaire qui pourrait

entraîner des blessures corporelles graves

ou même la mort si on omet de prendre les

précautions nécessaires.

8819864 Casque de soudeur à assombrissement automatique solaire V1,0

avec la technologie de lentilles bleues

4 En cas de questions techniques, appelez le 1-800-665-8685

ATTENTION ! Cet avis indique une situation possiblement

dangereuse qui peut entraîner des blessures

mineures ou modérées si on ne procède pas

de la façon recommandée.

AVIS ! Cet avis indique un risque particulier ou une

pratique non sécuritaire qui entraînera des

dommages au niveau de l'équipement ou des

biens, mais non des blessures corporelles.

AIRE DE TRAVAIL

1. Travaillez dans un environnement de travail sécuritaire.

Gardez votre aire de travail propre, bien éclairée et

exempte de toute distraction.

2. Assurez-vous que les personnes qui ne portent pas

l'équipement de sécurité approprié ne se trouvent pas à

proximité de l'aire de travail.

3. Rangez les outils correctement dans un lieu sécurisé et sec.

Gardez les outils hors de la portée des enfants.

SÉCURITÉ PERSONNELLE

AVERTISSEMENT ! Portez de l'équipement de protection

personnelle homologué par l'Association canadienne de

normalisation (CSA) ou l'American National Standards Institute

(ANSI).Personal Protective Equipment

1. Portez toujours des lunettes antiprojections qui offrent une

protection frontale et latérale pour les yeux.

2. Portez des gants qui protègent en fonction des matériaux de

travail et pour réduire les effets des vibrations de l’outil.

3. Portez des vêtements de protection conçus pour

l’environnement de travail et pour l’outil.

4. Gardez le contrôle de l’outil, de vos mouvements et de

l’environnement de travail pour éviter les blessures ou le

bris de l’outil.

La page est en cours de chargement...

PROPOINT 8819864 Le manuel du propriétaire

Marque: PROPOINT

Modèle: 8819864

Catégorie: Système de soudage

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: PROPOINT 8819864 Owner's manual

PROPOINT 8819864 Le manuel du propriétaire

PROPOINT 8819864 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents