Tele Radio CL-TR600-1 Manuel utilisateur

Marque
Tele Radio
Modèle
CL-TR600-1
Taper
Manuel utilisateur
CL-TR600-1, D00005-15, D5-15 User Manual
General
Power supply: The radio module use two LDO N5 and N1 to provide power for radio chip.
Transmit: The CC2520 features a Direct Conversion Transceiver operating in the 2.4Ghz band. During the
transmit stage, the CPU of mainboard send the data to the CC2520 through the SPI interface. When the
CC2520 get emission instruction from CPU, it will go into transmit mode and modulate data up to radio
band, after the modulation stage the modulated RF signal is sent to the PA of CC2592, the PA fulfil the
power amplification, finally the RF signal radiate out through the antenna.
Receive: During the receive stage, the CC2520 get a receipt instruction from CPU, it will go into receive
mode. The RF signal is received from antenna, it go into LNA of CC2592, the LNA amplifies the recieveed
RF signal, after that the RF signal go into the CC2520, the demodulator of CC2520 is responsible for
retrieving the sent data from the received signal, after demodulated the data will send to CPU through SPI
interface.
Frequency range: 2405-2480MHz
Modulation: O-QPSK
Max EIRP: 21.46dBm
Antenna port: Antenna 1 & 2 share the same RF port and are switched by a RF switch. The 3 antennas
cannot transmit at the same time
The compliance of KDB 996369 D02 Module Q&A v01 Question 11:
The external omni antenna is connected directly to the module by IPEX cable without passing through
other peripheral circuits, so this requirement is not applicable to the product.
The requirement for KDB 996369 D03:
1 List of applicable FCC rules
FCC Part 15. 247
2 Summarize the specific operational use conditions
None.
3 Limited module procedures
The module is a single module, so this requirement is not applicable to the product.
4 Trace antenna designs
The external omni antenna is connected directly to the module by IPEX cable, so this requirement is not
applicable to the product.
5 RF exposure considerations
The host device manufacturer should confirm that a separation distance of 20 cm or more should be
maintained between the antenna of this host device and persons during the host device operation.
6 Antennas
For 2.4G Band:
Ant1: Internal chip antenna, 4dBi;
Ant2: External omni antenna, 3dBi;
Ant3: Internal chip antenna, 4dBi
7 Label and compliance information
If this certified module is installed inside the host device, then the outside of the host must be labeled
with “Contains FCC ID: ONFC1602A and IC: 4807A-C1602A”.
8 Information on test modes and additional testing requirements
The host manufacturer can use software to make the transmit continuously.
9 Additional testing, Part 15 Subpart B disclaimer
The module only complies with the FCC Part 15.247. If the module is installed in the host device, the host
manufacturer is responsible for the compliance to any other FCC rules that apply to the host not covered
by the modular transmitter grant of certification. For example, if the host manufacturer markets their
product as being Part 15 Subpart B compliant (when it also contains unintentional-radiator digital
circuity), then the host manufacturer shall provide a notice stating that the final host product still requires
Part 15 Subpart B compliance testing with the modular transmitter installed.
FCC & IC application:
This device complies with Part 15 of the FCC Rules / Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause harmful interference,
and (2) this device mustaccept any interference received, including interference that may cause undesired
operation.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de
brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
Changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
MPE caution
To satisfy FCC&IC RF exposure requirements, a separation distance of 20 cm or more should be
maintained between the antenna of this device and persons during device operation.
To ensure compliance, operations at closer than this distance is not recommended.
Les antennes installées doivent être situées de facon à ce que la population ne puisse y être exposée à
une distance de moin de 20 cm. Installer les antennes de facon à ce que le personnel ne puisse approcher
à 20 cm ou moins de la position centrale de l’ antenne.
Information for the OEM Integrators
This device is intended for OEM integrators only. Please see the full grant of equipment document for
restrictions.
Label Information to the End User by the OEM or Integrators
If the FCC ID of this module is not visible when it is installed inside another device, then the outside of the
device into which the module is installed must be label with “Contains FCC ID: ONFC1602A and IC: 4807A-
C1602A”.
Antenna caution
This radio module IC: 4807A-C1602A has been approved by Innovation, Science and Economic
Development Canada to operate with the antenna types listed below, with the maximum permissible gain
indicated. Antenna types not included in this list that have a gain greater than the maximum gain
indicated for any type listed are strictly prohibited for use with this device.
Gain of antenna: 4dBi max for Chip antenna, 3dBi max for External omni antenna.
Type of antenna: 50ohm, Chip antenna, External omni antenna.
Le présent émetteur radio IC: 4807A-C1602A a été approuvé par Innovation, Sciences et Développement
économique Canada pour fonctionner avec les types d'antenne énumérés ci dessous et ayant un gain
admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est supérieur au gain
maximal indiqué pour tout type figurant sur la liste, sont strictement interdits pour l'exploitation de
l'émetteur.Gain d'antenne: 4dBi maximal
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Tele Radio CL-TR600-1 Manuel utilisateur

Marque
Tele Radio
Modèle
CL-TR600-1
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Autres documents