Pleasant Hearth PH50PS Series Le manuel du propriétaire

[email protected] 7077-171G • October 15, 2015 1

Questions, problems, missing parts? Before returning to your retailer,

call our customer service department at 877-447-4768 8:30 a.m – 4:30 p.m. CST,

Monday – Friday or email us at [email protected].

Owner’s Manual

Installation and Operation

Models:

PH35PS Series - Medium Pellet Stove with Pedestal

PH50PS Series - Large Pellet Stove with Pedestal and Base Pan

PH50CABPS Series - Cabinet Pellet Stove

High Efﬁ ciency Pellet Stove

SAFETY NOTICE: PLEASE READ THIS ENTIRE MANUAL BEFORE INSTALLATION AND USE OF

THIS PELLET FUEL-BURNING ROOM HEATER. FAILURE TO FOLLOW THESE INSTRUCTIONS

COULD RESULT IN PROPERTY DAMAGE, BODILY INJURY OR EVEN DEATH. CONTACT LOCAL

BUILDING OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION INSPECTION REQUIRE-

MENTS IN YOUR AREA.

SAVE THESE INSTRUCTIONS

6440 W. Howard St.

Niles, IL 60714

877-447-4768

This heater meets the U.S. Environmental Protection Agency’s

emission limits for wood heaters sold after July 1, 1990.

PH35PS PH50PS PH50CABPS

7077-171G • October 15, 2015 (877) 447- 47682

A

U

T

O

M

A

T

I

C

/

A

U

T

O

M

Á

T

I

C

O

/

A

U

T

O

M

A

T

I

Q

U

E

O

F

M

A

X

M

I

N

O

N

A

U

T

O

A

L

A

R

M

START

UP

GUIDE

4.

Check all three bafﬂ es are hooked

into slots.

*Before you plug in this appliance, follow these instructions*

3.

Verﬁ y ﬁ repot’s orientation is

correct.

5.

Plug power cord into wall

receptacle.

Wait one minute.

*Green light will start ﬂ ashing one time

per second*

7.

If the stove does not ignite follow

directions below. The LED light

should blink red four times showing

a missed ignition.

Turn the stove to off, remove and

EMPTY the ﬁ repot.

CAUTION

Overﬁ lling the ﬁ repot could cause an

unsafe ignition resulting in injury or

damage. Firepot must be emptied.

Return the ﬁ repot to the stove

correctly (step 3) and then repeat

step 6.

8.

Once a ﬁ re has been established

in the stove, leave the stove

burning on HI for 30 minutes to

allow paint to cure.

NOTE: Odors, vapors, and

smoke are released during initial

operation. Open windows or doors

for air circulation until burn off is

complete.

9.

After 30 minutes have passed, turn the dial control to OFF and then allow unit

to cool completely. Once cooled, open the door and clean the ﬁ repot according

to the cleaning instructions found on the inside of the hopper lid, in the owners

manual, or on PelProStoves.com.

*Unit is now ready to resume normal operation*

6.

To prime the feed tube, QUICKLY

turn the dial control from OFF to HI,

back to OFF, then back to HI. The

feed motor will run continuously for

2 minutes and the LED light will be

solid green.

Once primed, pellets will drop

into the ﬁ repot and the LED light

will blink green as the ignition

sequence starts.

Important: Allow up to 20 minutes

for ignition to take place.

CAUTION

Do not restart, manually add pellets,

or use any type of accelerant during

this process.

NOTE:

Priming is only required

the ﬁ rst time the appliance is lit,

or after the hopper has run

completely out of pellets.

1.

Turn Dial Control to OFF.

All material needs to be removed

from the door glass and ﬁ rebox

before operation.

Follow all instructions and warn-

ings for safe start up of stove.

Failure to follow instructions

could result in injury or damage.

2.

Add pellets to hopper and close lid.

Back

Hole for Igniter

V

EL

Front

of

ﬁ repot

has

the lip

A

U

T

O

M

A

T

I

C

/

A

U

T

O

M

Á

T

I

C

O

/

A

U

T

O

M

A

T

I

Q

U

E

O

F

M

A

X

M

I

N

O

N

A

U

T

O

A

L

A

R

M

[email protected] 7077-171G • October 15, 2015 3

TABLE OF CONTENTS

Safety Alert Key:

• DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.

• WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.

• CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

• NOTICE: Indicates practices which may cause damage to the appliance or to property.

Section 1: Listing and Code Approvals

A. Appliance Certiﬁ cation ...............................5

B. Mobile Home Approved .............................5

C. Glass Speciﬁ cations...................................5

D. Electrical Rating .........................................5

E. BTU & Efﬁ ciency Speciﬁ cations .................5

Section 2: User Guide: General Information

A. Fire Safety .................................................6

B. Combustible/Non-Combustible

Materials ....................................................6

C. Fuel Material & Fuel Storage .....................6

D. Before Your First Fire ................................6

Section 3: User Guide: General Operating Information

A. User Dial Control ........................................7

B. Filling the Hopper .......................................7

C. Priming the Feed Tube ..............................7

D. Firepot Purge Cycle ...................................8

E. Shutdown ...................................................8

F. Starting Your First Fire ...............................8

G. Fire Characteristics ....................................8

H. Your Pellet Appliance.................................9

I. LED Color Coding Chart & Explanation .....10

J. Ignition Cycles............................................11

K. Running in Minimum or Maximum .............11

L. Running in the Automatic Mode .................11

M. Clear Space ...............................................11

N. Trim Adjustments .......................................11

Section 4: Maintaining & Servicing Your Appliance

A. Proper Shutdown Procedure......................12

B. Quick Reference Maintenance Chart .........12

C. General Maintenance .................................12

D. High Ash Fuel Content Maintenance..........16

E. Frequently Asked Questions .....................17

Section 5: Replacement Parts

A. Convection Blower Replacement ...............18

B. Exhaust Blower Replacement ....................18

C. Snap Disc Replacement ............................19

D. Igniter Replacement ...................................19

E. Bafﬂ e Removal & Replacement .................19

F. Glass Replacement....................................20

G. Control Board Replacement.......................20

H. Fuse Replacement .....................................20

I. Feed Motor Replacement ..........................20

J. Feed Spring Replacement .........................20

Section 6: Getting Started

A. Design, Installation & Location

Considerations...........................................21

B. Draft ...........................................................21

C. Negative Pressure .....................................21

D. Locating Your Appliance & Chimney .........22

E. Inspect Appliance & Components .............22

F. Tools & Supplies Needed ..........................22

Section 7: Dimensions and Clearances

A. Appliance Dimension: PH35PS .................23

B. Appliance Dimension: PH50PS .................23

C. Appliance Dimension: PH50CAB ..............24

D. Clearances to Combustibles (UL & ULC) ..24

E. Hearth Pad Requirements (UL & ULC) .....25

Section 8: Vent Information

A. Chimney & Exhaust Connection ................26

B. Venting Termination Requirements ...........26

C. Pellet Venting Charts .................................27

Section 9: Venting Systems

A. Vertical- Interior- Typical Installation ..........28

B. Through the Wall & Vertical .......................28

C. Vertical into Existing Class A Chimney ......28

D. Masonry .....................................................29

E. Alternate Masonry ......................................29

F. Through the Wall........................................30

Section 10: Mobile Home .....................................31

Section 11: Appliance Set-Up..............................32

Section 12: Troubleshooting ...............................33

Section 13: Reference Materials

A. Component Functions ...............................36

B. Wiring Harness ..........................................37

C. Replacement Parts ....................................38

D. 5 Year Warranty ........................................39

Contact Information ...................................40

French Manual.....................................................41

Spanish Manual...................................................81

7077-171G • October 15, 2015 (877) 447- 47684

CAUTION

After reading these instructions, if you have any doubt

about your ability to complete your installation in a pro-

fessional manner you should obtain the services of an

installer versed in all aspects as to the correct and safe

installation. Do not use temporary makeshift compro-

mises during installation.

BEFORE INSTALLATION OF YOUR APPLIANCE

1. Check with the building inspector’s ofﬁ ce for

compliance with local codes; a permit may be

required.

2. Use 3” or 4” (76-102mm) diameter type “L” or

“PL” venting system. It can be vented vertically or

horizontally. Approved adaptors can be used to

connect the “L” or” PL” to approved wood stove

venting such as single wall or double wall venting

previously used to vent a wood burning appliance.

INSTALL VENT AT CLEARANCES SPECIFIED BY

THE VENT MANUFACTURE.

3. Always connect this unit to an approved chimney

system and NEVER vent to another room or inside

a building.

4. DO NOT INSTALL A FLUE DAMPER IN THE

EXHAUST VENTING SYSTEM OF THIS UNIT.

5. DO NOT CONNECT THIS UNIT TO A CHIMNEY

FLUE SERVING ANOTHER APPLIANCE.

6. The connector pipe and chimney should be

inspected periodically and cleaned if necessary.

Review additional information located in the mainte-

nance section of this Owner’s Manual.

7. Remember the clearance distances when you

place furniture or other objects within the area.

This includes heat sensitive materials such as

candles, seasonal decorations or draperies. DO

NOT STORE WOOD, FLAMMABLE LIQUIDS OR

OTHER COMBUSTIBLE MATERIALS TOO CLOSE

TO THE UNIT.

8. Be aware of the required clearances when locat-

ing the unit. Refer to the label on the rear of the

unit for required clearances.

9. Contact your local municipal or provincial ﬁ re

authority for information of how to handle a chim-

ney ﬁ re. Have a clear understood plan to handle a

chimney ﬁ re. In the event of a chimney ﬁ re, CALL

THE FIRE DEPARTMENT.

10. Prior to burning the unit for the ﬁ rst time make

sure the hardware kit has been removed from the

ﬁ rebox.

IMPORTANT

It is highly recommended that the pellet heater

and chimney be installed by a qualiﬁ ed installer. A

qualiﬁ ed installer is a person or entity who regularly

installs solid burning fuel products and chimneys in

the course of their ordinary business.

If the information in these

instructions is not followed

exactly, a ﬁ re may result causing

property damage, personal injury,

or death.

• Do not store or use gasoline or other ﬂ am-

mable vapors and liquids in the vicinity of

this or any other appliance.

• Do not over ﬁ re - If heater or chimney con-

nector glows, you are over ﬁ ring. Over ﬁ ring

will void your warranty.

• Comply with all minimum clearances to

combustibles as speciﬁ ed. Failure to

comply may cause house ﬁ re.

WARNING

Hot glass will cause burns.

• Do not touch glass until it is cooled

• NEVER allow children to touch glass

• Keep children away

• CAREFULLY SUPERVISE children in same room as

ﬁ replace.

• Alert children and adults to hazards of high

temperatures.

High temperatures may ignite clothing or other

ﬂ ammable materials.

• Keep clothing, furniture, draperies and other ﬂ ammable

materials away.

HOT SURFACES!

Glass and other surfaces are hot

during operation AND cool down.

WARNING

Fire Risk.

Tested and approved for wood

pellets. Burning of any over type

of fuel will void your warranty.

WARNING

[email protected] 7077-171G • October 15, 2015 5

A. Appliance Certiﬁ cation

This appliance is equipped with 5mm ceramic glass.

Replace glass only with 5mm ceramic glass. Please contact

GHP for replacement glass.

C. Mobile Home Approved

NOTE: This installation must conform with local codes.

In the absence of local codes you must comply with the

ASTM E1509-04, ULC S627-00, (UM) 84-HUD,

Series: PH35PS, PH50PS, PH50CABPS

Laboratory: Intertek

Report No. 10072262PRT-001

Type: Solid Fuel Room Heater/Pellet

Fuel Burning Type

Standard: ASTM E1509-04 and ULC S627-

00, Room Heater Pellet Fuel

Burning type and (UM) 84-HUD,

Mobile Home Approved.

• This appliance is approved for mobile home

installations when not installed in a sleeping room and

when an outside combustion air inlet is provided.

• The structural integrity of the mobile home ﬂ oor,

ceiling, and walls must be maintained.

• The appliance must be properly grounded to the frame

of the mobile home with #8 copper ground wire, and

use only listed double-wall connector pipe.

• Outside Air Kit provided with each unit must be

installed in a mobile home installation.

WARNING! Risk of Fire! GHP disclaims any responsibility

for, and the warranty and agency listing will be voided by the

below actions.

DO NOT:

• Install or operate damaged appliance

• Modify appliance

• Install other than as instructed by the manufacturer.

• Operate the appliance without fully assembling all

components

• Over ﬁ re

• Install any component not approved by the

manufacturer

• Install parts or components not Listed or approved

• Disable safety switches

Improper installation, adjustment, alteration, service or

maintenance can cause injury or property damage.

For assistance or additional information, consult a qualiﬁ ed

installer, service agency or your dealer.

PH35PS Series:

115 VAC, 60 Hz, Start 2.6 Amps,

Run 0.9 Amps

PH50PS Series: 115 VAC, 60 Hz, Start 2.6 Amps,

Run 0.9 Amps

PH50CABPS Series: 115 VAC, 60 Hz, Start 2.6 Amps,

Run 0.9 Amps

D. Glass Speciﬁ cations

E. Electrical Rating (On High)

The Quadra-Fire Pleasant Hearth Pellet Heater meets the

U.S. Environmental Protection Agency’s emission limits for

pellet heaters sold after May 15, 2015.

This pellet heater needs periodic inspection and repair for

proper operation. It is against federal regulations to operate

this pellet heater in a manner inconsistent with operating

instructions in this manual.

PH35 PH50

PH50CAB

EPA Certiﬁ cation #: 907 904

EPA Certiﬁ ed Emissions: 0.3 0.7 grams/hour

*LHV Tested Efﬁ ciency: N/A N/A %

**HHV Tested Efﬁ ciency: 83.8 84.4 %

***EPA BTU Output: 9,600

to

25,000

9,300 to

32,400

per hr.

****BTU Input: 12,900

to

34,400

12,500 to

43,900

per hr.

Vent Size: 3 or 4 inches, “L” or “PL”

Hopper Capacity: 40 80/120 lbs.

Fuel Wood Pellets

* Weighted average LHV efﬁ ciency using data collected during

EPA emissions test.

**Weighted average HHV efﬁ ciency using data collected during

EPA emissions test.

***A range of BTU outputs based on EPA Default Efﬁ ciency and

the burn rates from the low and high EPA tests.

****Based on the maximum feed rate per hour multiplied by

approximately 8600 BTU’s which is the average BTU’s from a

pound of pellets.

B. BTU & Efﬁ ciency Speciﬁ cations

1

Listing and Code Approvals

7077-171G • October 15, 2015 (877) 447- 47686

A. Fire Safety

To provide reasonable ﬁ re safety, the following should be

given serious consideration:

• Install at least one smoke detector on each ﬂ oor of your

home.

• Install at least one carbon monoxide detector on each ﬂ oor

of your home.

• Locate smoke detector away from the heating appliance

and close to the sleeping areas.

• Follow the smoke detector manufacturer’s placement and

installation instructions and maintain regularly.

• Follow the carbon monoxide manufacturer’s placement and

installation instructions and maintain regularly.

• Conveniently locate a Class A ﬁ re extinguisher to contend

with small ﬁ res.

• In the event of a hopper ﬁ re:

• Evacute the house immediately.

• Notify ﬁ re department.

B. Combustible/Non-Combustible Materials

• Combustible Material

Material made of or surfaced with wood, compressed

paper, plant ﬁ bers, plastics, or any material capable

of igniting and burning, whether ﬂ ame-proofed or not,

plastered or unplastered.

• Non-combustible Material

Material which will not ignite and burn. Such materials are

those consisting entirely of steel, iron, brick, tile, slate,

glass or plasters, or any combination thereof.

• Non-combustible Sealant Material

Sealants which will not ignite and burn: Rutland, Inc.

Fireplace Mortar #63, Rutland 76R, Nuﬂ ex 304, GE

RTV106 or GE RTB116 (or equivalent).

C. Fuel Material and Fuel Storage (Cont’d)

Lower Ash Content Material

• Most softwoods

• Fuels with low mineral content

• Most premium grade pellets

Clinkers

Minerals and other non-combustible materials such as sand

will turn into a hard, glass-like substance called a clinker when

heated in the ﬁ repot.

Trees from different areas will vary in mineral content. That

is why some fuels produce more clinkers than others.

Moisture

Always burn dry fuel. Burning fuel with high moisture content

takes heat from the fuel and tends to cool the appliance,

robbing heat from your home. Damp pellet fuel can clog the

feed system.

Size

•

Pellets are either 1/4 inch or 5/16 inch (6-8mm) in diameter

• Length should be no more that 1-1/2 inches (38mm)

• Pellet lengths can vary from lot to lot from the same

manufacturer

• Due to length variations, the feed rate may need adjusting

occasionally

Performance

• Higher ash content requires the ﬁ repot and the ash drawer

to be emptied more frequently

• Hardwoods require more air to burn properly

• Premium wood pellets produce the highest heat output

• Burning pellets longer than 1-1/2 inches (38mm) can cause

an inconsistent fuel feed rate and/or missed ignitions of

feed jams.

Storage

• Wood pellets should be left in their original sealed bag until

using to prevent moisture absorption

• Do not store any pellet fuel within the clearance requirements

or in an area that would hinder routine cleaning and

maintenance

C. Fuel Material and Fuel Storage

Pellet fuel quality can greatly ﬂ uctuate. We recommend that

you buy fuel in multi-ton lots whenever possible. However,

we do recommend trying various brands before purchasing

multi-ton lots to ensure your satisfaction.

Fuel Material

• Made from sawdust or wood by-products

• Depending on the source material it may have a high or

low ash content.

Higher Ash Content Material

• Hardwoods with a high mineral content

• Fuel that contains bark

• Standard grade pellets or high ash pellets

D. Before Your First Fire

1. First, make sure your appliance has been properly

installed and that all safety requirements have been met.

Pay particular attention to the ﬁ re protection and venting.

2. Double check that the ﬁ rebox is empty and the ﬁ repot is

in place!

3. Close and latch the door.

2

User Guide: General Information

[email protected] 7077-171G • October 15, 2015 7

A. User Dial Control

The appliance has one dial control located on the side of

the unit used for daily operation. There are four primary

settings on this dial.

1) Off : When the dial indicator is in the off position

the unit will go into a shut down and remain off

until the dial is turned to one of the other three

settings. The LED will ﬂ ash green once per

second when in the off position.

2) MIN : When the dial indicator is directed to the

MIN setting (small ﬂ ame on the label) the unit

will burn on low until the hopper runs out of

pellets or the dial control is turned to a different

setting. When in this setting the LED will be

amber in color and continuously on. When

burning in this mode, the unit should be turned

off at least once daily for cleaning. If lower

quality fuels are used, additional daily shut

downs may be required for cleaning.

3: MAX : Similar to the MIN mode, the unit will

run continuously at the high burn rate until the

unit has run out of fuel or the dial is turned to a

different setting. To operate in this mode, turn the

dial clockwise until it stops. The dial

indicator will point to the large ﬂ ame. When in

this setting the LED will be amber in color and

continuously on. Follow the daily cleaning

recommendations when operating in this mode. If

lower quality fuels are used, additional daily shut

downs may be required for cleaning.

4: AUTO : To burn in the Automatic mode, turn

the dial control clockwise to the desired comfort

level. When operating in the automatic mode, the

unit changes the burn setting based on the

difference between the room temperature and the

desired set point. In other words, the unit will

burn on High if the difference between the

desired and room temperature is greater than 8

degrees Fahrenheit. As the room heats up and

the gap closes, the unit will automatically reduce

the burn rate. When the room temperature is close

to the set point th elight will stop ﬂ ashing stay solid

green. at this time the stove will be burning on the

lowest burn rate. When the desired temperature is

achieved the unit will shut down. As the room cools,

the unit will restart automatically. When burning

in this mode the LED will be blinking green. The

number of green ﬂ ashes corresponds to the current

burn rate.

B. Filling the Hopper

Slowly open the hopper lid by lifting the handle. The

medium and large units have a locking latch that will

engage when the hopper lid is fully opened. The hopper

lid for the cabinet will open past ninety degrees and

stay open automatically. Fill the hopper with fuel. FOR

USE WITH ONLY WOOD PELLET FUEL. Slowly close

the hopper lid. See ﬁ gure below for releasing the latch.

NOTE: The unit will not feed with the hopper lid open. If

left open, the ﬁ re will go out.

0

-

1

-

2

-

3

-

4

+

1

+

2

+

3

+

4

A

U

T

O

M

A

T

I

C

/

A

U

T

O

M

Á

T

I

C

O

/

A

U

T

O

M

A

T

I

Q

U

E

O

F

M

A

X

M

I

N

O

N

A

U

T

O

A

L

A

R

M

Push Bottom of Latch

Inward to Release

C. Priming the Feed Tube

Only if the hopper is being ﬁ lled for the ﬁ rst time or the

unit had previously run out of pellets, the feed tube may

need to be primed. To do this, turn the dial control from

the OFF position to the MAX position two times. This

will run the feed motor continuously for two minutes

without turning the igniter on. When the auger is running

continuously, the LED will be a continuous green color.

The system will run the auger for 2 minutes. When pel-

lets start to drop into the ﬁ repot, the feed tube is primed;

turn the dial control to the desired position and the stove

will begin its ignition sequence (The green LED will ﬂ ash

rapidly).

CAUTION

Do not restart or manually add pellets or any type

of fuel to the burn pot during this process.

3

User Guide: General Operating Information

7077-171G • October 15, 2015 (877) 447- 47688

F. Starting Your First Fire

1) Turn the dial control to “OFF”.

2) Make sure the ﬁ repot is clean, inplace, and free of

debris.

3) Plug the unit into the wall and ﬁ ll the hopper with

wood pellets. Shut the hopper lid.

4) Turn the dial control to the desired burn setting.

The unit will go into the ignition sequence followed by

start up (The green LED will ﬂ ash rapidly). The igni-

tion sequence involves the exhaust blower turning on,

the igniter turning on, and the feed motor running in two

stages. The ﬁ rst stage involves the feed motor running

continuously for about a minute to preload pellets into the

ﬁ repot. Following the preload and a delay, the feed motor

will begin cycling on and off. When the pellets are warming

up and on the verge of igniting, it is not uncommon for the

ﬁ rebox to ﬁ ll with smoke. Once ignition actually happens,

the smoke should evacuate quickly. During this stage as

well as any part during the burn process, the front door

should not be opened. This cycle continues until the unit

senses ignition by a rise in the exhaust temperature or the

unit times out. Following the ignition cycle the unit begins

to feed additional pellets gradually for a few minutes to

build up the ﬁ re. This is important to have a controlled start

up to keep the unit in balance.

G. Fire Characteristics

The overall height of the ﬂ ame will vary throughout the burn

for a couple of reasons. First is that the ﬂ ame will vary

based on type of fuel or even batch of fuel. Sencondly,

the unit adjusts the burn rate according to the how far

away the room temperature is from the set temperature.

This should not cause alarm. The third characteristic that

affects the ﬁ re relates to general maintenance and clean-

ing. Infrequent or poor general maintenance will result is

poorer performance. Indicators of the need for additional

maintenance activities include a lazy ﬂ ame, black sooted

glass, pellets not igniting, or pellets falling to the side of the

ﬁ repot. See the maintenance section for additional infor-

mation.

Odors and vapors released during initial operation.

• Curing of high temperature paint.

• Open windows for air circulation.

Odors may be irritating to sensitive individuals.

CAUTION

D. Firepot Burn Down

A feature of these pellet stoves is the ﬁ repot burn down

cycle. The frequency of the cycle is once every hour the

unit is burning. During this event, the feed is reduced to

the lowest setting and the exhaust blower ramps up to

the highest setting. The purpose of the burn down cycle

is to help remove debris from the ﬁ repot and help the unit

burn as efﬁ cient as possible. The cycle lasts 99 seconds.

Please be aware that the burn down does not replace daily

cleaning activities but makes them easier.

E. Shutdown

T

o shut the appliance down, turn the dial control counter

clockwise to the OFF position. During the shutdown pro-

cess, the LED will ﬂ ash green rapidly just like the ignition

sequence. The ﬁ repot burn down cycle will begin but with-

out the feed motor running. The feed will be terminated

during this shutdown process. The exhaust and convection

blowers will remain on during the shutdown process until

the exhaust has cooled.

C. Priming the Feed Tube (Cont’d)

A FIREPOT THAT IS MORE THAN HALF FULL IS OVER-

FILLED AND CAN BE DANGEROUS. DO NOT OVERFILL

FIREPOT FOR IGNITION.

If the stove does not ignite follow directions below. The

LED light should blink red four times showing a missed

ignition.

Turn the stove to off and remove and EMPTY the ﬁ repot.

CAUTION

Overﬁ lling the ﬁ repot could cause an unsafe

ignition resulting in injury or damage. Firepot must

be emptied.

Return the ﬁ repot to the stove correctly (step 3) and then

repeat step 6.

MAXIMUM

PELLET LEVEL

If maintenance or daily cleaning is going to be conducted

immediately following a shutdown, please use caution as

components especially those inside the ﬁ rebox may still be

hot.

Please note that if the dial control is turned to the off

position and back on even if by mistake, the unit will

go through the shutdown sequence.

3

User Guide: General Operating Information

[email protected] 7077-171G • October 15, 2015 9

H. Your Pellet Appliance - General Operating Parts

WARNING

Hot glass will cause burns.

• DO NOT touch glass until it is cooled

• NEVER allow children to touch glass

• Keep children away

• CAREFULLY SUPERVISE children in same room as appliance.

• Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other ﬂ ammable materials.

• Keep clothing, furniture, draperies and other ﬂ ammable materials away.

HOT SURFACES!

Glass and other surfaces are hot during operation AND cool down.

NOTICE: If you expect that children may come into contact with this appliance, we recom-

mend a barrier such as a decorative screen. See your retailer for suggestions.

Baffles (3)

Firepot

Drop Tube

Hopper Lid Switch Dial Control

3

User Guide: General Operating Information

7077-171G • October 15, 2015 (877) 447- 476810

LED

Color

Number of

Flashes between

pauses

Description Notes

Green Steady ON while

priming feed tube

(max time 2 min-

utes)

Feed Motor is running continuously.

(This primes the feed tube).

When priming the feed system and ﬁ lling

the ﬁ repot, DO NOT OVERFILL FIREPOT

FOR IGNITION. The unit will automatically

go into start up following the prime function.

Green Steady ON while

burning

Room temperature is close to set

point and burning on lowest burnt

rate.

Green 1x Unit is off and ready.

To start appliance, follow start up sequence.

Green 3x Appliance is in the start up/ignition

sequence or in shutdown.

During shut down, the blowers will shut off

when the exhaust temperature has cooled.

Green Varies

When in the automatic mode, the

number of ﬂ ashes between pauses

indicates the burn rate (1 for low up to

5 for high).

Adjust the dial control to change the desired

room temperature.

Amber Steady ON

Appliance is set and running at either

the minimum or maximum power

levels.

The unit will shut off only when the hopper

runs out of fuel, the user changes the

dial control to a different state, or the unit

senses an error.

Red

1x

Empty Hopper Alarm

This alarm is caused by the ﬁ re going out

from lack of fuel. See troubleshooting sec-

tion for more information.

Red 2x Exhaust Probe Alarm Failed component error. See troubleshoot-

ing section for more information.

Red 3x Ambient Probe Alarm Failed component error. See troubleshoot-

ing section for more information.

Red 4x Missed Ignition

There are a total of 2 tries per ignition

sequence. If after 2 tries there is no rise in

exhaust temperature this error will occur.

See the troubleshooting section for addi-

tional information and correction.

Red 8x Exhaust Gas Over Temperature Alarm The exhaust temperature exceed the allow-

able limit. See the troubleshooting section

for more information and correction.

I. LED Color Coding Chart and Explanation

WARNING

Fire Risk

Do NOT operate appliance:

• With appliance door open.

• Firepot ﬂ oor open.

Do NOT store fuel:

• Closer than required clearances to com-

bustibles to appliance

• Within space required for loading or ash

removal.

3

User Guide: General Operating Information

[email protected] 7077-171G • October 15, 2015 11

N. Trim Adjustment

The small dial located below the main dial control is used

to adjust the amount of combustion air for the ﬁ re. You

may need to adjust the combustion air to the ﬁ re for:

Elevation

Venting/Installation Conﬁ gurations

Fuel Quality

If your ﬁ re is too large, lazy, or producing black soot, you

need MORE air. To increase the amount of combus-

tion air, rotate counterclockwise one level at a time and

allow 15 minutes for stabilization prior to making another

adjustment. If your ﬁ re is too small and sometimes goes

out when there are pellets in the hopper, you may have

too much air (too lean). To decrease the amount of

combustion air, rotate clockwise one level at a time and

allow 15 minutes for stabilization prior to making another

adjustment.

J. Ignition Cycles

1. At the beginning of each ignition cycle, it is normal to see

some smoke in the ﬁ rebox. The smoke will stop once

the ﬁ re starts.

2. The convection blower will automatically turn on after

your appliance has been burning for approximately 10

minutes.

This blower transfers heat from your appliance into the

room, and will continue to run even after the unit has

shutdown. It will turn off after the exhaust temperature

has cooled.

3. Occasionally the appliance may run out of fuel and shut

itself down. When this happens the empty hopper alarm

will be triggered.

WARNING! RISK OF FIRE! Keep combustible materials,

gasoline and other ﬂ ammable vapors and liquids clear of

appliance.

• Do NOT

store ﬂ ammable materials in the appliance’s

vicinity.

• Do NOT use gasoline, lantern fuel, kerosene, charcoal

lighter ﬂ uid or similar liquids to start or “freshen up” a ﬁ re

in this heater.

Keep all such liquids well away from the heater while it is in

use as combustible materials may ignite.

M. Clear Space

WARNING! RISK OF FIRE! Do NOT place combustible

objects in front or to the sides of the appliance. High tem-

peratures may ignite clothing, furniture or draperies.

NOTICE: Clearances may only be reduced by means ap-

proved by the regulatory authority having jurisdiction.

Mantel:

Avoid placing candles and other heat-sensitive

objects on mantel or hearth. Heat may damage these

objects.

K. Running in Minimum or Maximum

When the dial control is set to run on the minimum or

maximum setting, the appliance will continue to run

without regard to the actual temperature in the room.

The appliance will shut off only if the dial control is set to

a different setting or there is an error such as an empty

hopper.

When running on minimum or maximum it is important to

follow the daily cleaning activities especially cleaning the

ﬁ repot. Failure to do so will reduce the performance of the

appliance.

L. Running in the Automatic Mode

When the dial control is set to run in the automatic mode

the unit will adjust the actual burn rate based on the

difference between the room temperature as sensed by

the probe located in the rear of the unit and the desired

comfort level as set on the dial control.

The comfort level range is from 65 degrees Fahrenheit to

82 degress Fahrenheit.

Once the desired comfort level is achieved the appliance

will automatically shut down and turn off. When the

temperature in the room drops 3 degrees below the

desired comfort level, the appliance will automatically

restart.

3

User Guide: General Operating Information

7077-171G • October 15, 2015 (877) 447- 476812

C. General Maintenance

1. Types of Fuel

The type of fuel you are burning will dictate how often you

have to clean your ﬁ repot.

If the fuel you are burning has a high dirt or ash content, it may

be necessary to clean the ﬁ repot more than once a day.

Poor quality fuel will cause clinkers to form in the ﬁ repot. A

clinker is formed when dirt, ash or a non-burnable substance

is heated to 2000°F (1093°C) and becomes glass-like. See

section D following for more details on fuels with high ash

content.

Shock and Smoke Hazard

• Turn dial control to OFF, let appliance complete-

ly cool and exhaust blower must be off. Now

you can unplug appliance before servicing.

• Smoke spillage into room can occur if appliance

is not cool before unplugging.

• Risk of shock if appliance not unplugged before

servicing appliance.

CAUTION

A. Proper Shutdown Procedure

Cleaning or Inspection

Frequency Daily Weekly Monthly Yearly

Firepot Every 3 bags of fuel OR X

Ash Removal from Firebox Every 5 bags of fuel or more

frequently depending on ash

build-up

OR X

Glass When clear view of ﬁ repot

becomes obscure

OR X

Hopper Every 25 bags of fuel OR X

Exhaust Path, Drop Tube and Behind

Bafﬂ es

Every 25 bags or more fre-

quently depending on ash

build-up

OR X

Door Handle & Gasket Inspection Prior to heating season OR X

Blower, Convection Every 25 bags or more fre-

quently depending on operat-

ing environment.

OR X

Blower, Exhaust More frequently depending on

the fuel type

OR X

Firebox - Prepare for Non-Burn Season At end of heating season OR X

Venting System Every 3 tons or more fre-

quently depending on the fuel

type

OR X

B. Quick Reference Maintenance Chart

Follow the detailed instructions found in this

section for each step listed as referenced in

the chart below.

NOTICE: These are recommendations. Clean more frequently if you encounter heavy build-up of

ash at the recommended interval or you see soot coming from the vent. Not properly

cleaning your appliance on a regular basis will void your warranty.

4

Maintaining & Servicing Your Appliance

[email protected] 7077-171G • October 15, 2015 13

2. Cleaning Firepot with the Firepot Clean-Out Tool;

• Frequency: Daily or more often as needed

• By: Homeowner

3. Ash Removal from Firebox

• Frequency: Weekly or more frequently depending on

ash build-up.

• By: Homeowner

a. The appliance must be in complete shutdown and cool

and the exhaust blower off. If you are just cleaning the

ﬁ repot, there is no need to unplug the appliance.

b. Open the front door of the appliance and lift out the

firepot. Use the firepot cleaning tool to break up

deposits inside the ﬁ repot and dispose in an approved

container. Depending on the quality of fuel used, the

fornt of the ﬁ repot may need to be removed for better

access for cleaning.

c. Use the narrow end of the ﬁ repot cleaning tool to clean

the holes.

d. With the ﬁ repot out clean the area below the ﬁ repot.

e. Reassemble the ﬁ repot and place back inside the ﬁ repot

riser. Make sure the ﬁ repot is in the correct direction

with the slanted lip in the rear. Failure to install the

ﬁ repot correctly may result in missed ignitions.

a. There must not be any hot ashes in the ﬁ rebox during

cleaning so allow the appliance to completely cool. The

ﬁ rebox ash should be removed every time the exhaust

path is cleaned. Frequent cleaning of the ash in the

ﬁ rebox will help slow down the build-up of ash in the

exhaust blower and vent system.

b. Vacuum out the ﬁ rebox thoroughly on both sides of the

ﬁ rebox and the ﬂ oor and ceiling. Remember to place

the ash and debris into a metal or non-combustible

container.

See Disposal of Ashes.

Disposal of Ashes

WARNING

• Ashes should be placed in metal container

with tight ﬁ tting lid.

• Ashes should be retained in closed container

until all cinders have thoroughly cooled.

4. Disposal of Ashes

• Frequency: As needed

• By: Homeowner

Ashes should be placed in a metal container with a

tight-ﬁ tting lid. The closed container of ashes should

be placed on a non-combustible ﬂ oor or on the ground,

well away from all combustible materials, pending ﬁ nal

disposal.

If the ashes are disposed of by burial in soil or otherwise

locally dispersed, they should be retained in the

closed container until all cinders have been thoroughly

cooled.

4

Maintaining & Servicing Your Appliance

7077-171G • October 15, 2015 (877) 447- 476814

8. Cleaning the Exhaust Path, Bafﬂ es & Drop Tube

• Frequency: Monthly or every 25 bags or more fre-

quently depending on ash build-up.

• By: Homeowner

a. Appliance must be completely cool.

b. Open the door and remove the center bafﬂ e ﬁ rst and

then the right and left bafﬂ es. Thoroughly vacuum the

exhaust path and drop tube and continue throughout

the rest of the ﬁ rebox. Also vacuum the front and

back of the bafﬂ es.

c. Using a small brush, brush the inner walls of the

exhaust outlet from the access hole inside the ﬁ rebox.

The access hole will be visible following the removal

of the left side bafﬂ e. After loosening up debris on

the inner walls of the outlet, vacuum out.

This is important as the exhaust temperature

probe is attached to the right side of the outlet.

If this is not maintained on a regular basis, the

appliance will experience nuisance shut downs

and/or missed ignitions.

d. Replace the right and left bafﬂ es and then the center

bafﬂ e and close and latch the door.

7. Cleaning the Hopper

• Frequency: Monthly or after burning 25 bags of fuel

• By: Homeowner

After burning approximately 25 bags of fuel you will

need to clean the hopper to prevent sawdust build-up.

A combination of sawdust and pellets on the bottom

end of the auger reduces the amount of fuel supply to

the ﬁ repot. This can result in nuisance shutdowns and

mis-starts.

a. The appliance must be in complete shutdown.

Allow the appliance to completely run out of pellets

and cool down.

b. Empty the hopper of any remaining pellets.

c. Vacuum the hopper and feed tube. To access the

feed tube remove the four screws from the auger

cover located inside of the hopper.

6. Cleaning the Glass

• Frequency: When clear view of the ﬁ repot becomes

obscure

• By: Homeowner

a. Appliance must be completely cool before cleaning

glass.

b. Vacuum ﬂ y ash from glass and door rope.

c. Use a damp paper towel or any non-abrasive glass

cleaner. Wipe off with dry towel.

Handle glass assembly with care.

When cleaning glass:

• Avoid striking, scratching or

slamming glass.

• Do NOT clean glass when hot.

CAUTION

• Do NOT use abrasive cleaners.

• Refer to maintenance instructions.

• Do NOT operate with glass cracked,

broken or scratched.

9. Door Handle Inspection

• Frequency: Monthly or prior to heating season

• By: Homeowner

The gasketing between the glass and ﬁ rebox should be

inspected periodically to make sure there is a good seal.

NOTE: GHP recommends using a

heavy duty vacuum

cleaner speciﬁ cally designed for solid fuel appli-

ance cleaning.

1

2

3

4

Maintaining & Servicing Your Appliance

[email protected] 7077-171G • October 15, 2015 15

13. Soot and Fly Ash: Formation & Need for Removal

in Exhaust Venting System.

• Frequency: Yearly or more frequently depending on

ash build-up.

• By: Qualiﬁ ed Service Technician/Homeowner

Be sure the appliance is allowed to cool, has been unplugged

and the exhaust blower is off.

The products of combustion will contain small particles of ﬂ y

ash. The ﬂ y ash will collect in the exhaust venting system

and restrict the ﬂ ow of the ﬂ ue gases.

At start-up if there is incomplete combustion, or if there is a

shutdown or incorrect operation of the appliance it will lead

to some soot formation. This will collect in the exhaust vent-

ing system.

The venting (chimney) system may need to be cleaned at

least once a year or more often depending upon the qual-

ity of your fuel or if there are any horizontal pipe sections.

Ash will build up more quickly in the horizontal sections and

elbows.

11. Cleaning Exhaust Blower - Requires No

Lubrication

• Frequency: Yearly or more frequently depending on

ash build-up

• By: Homeowner or Qualiﬁ ed Service Technician

10. Cleaning Convection Blower - Requires No

Lubrication

• Frequency: Monthly depending on Dust/Dirt build-up

• By: Homeowner or Qualiﬁ ed Service Technician

12. Preparing Firebox for Non-Burn Season

• Frequency: Yearly

• By: Homeowner

a. Be sure the appliance is allowed to cool, has been

unplugged and the exhaust blower is off.

b.

Remove all ash from the ﬁ rebox and vacuum thorough-

ly.

c. Paint all exposed steel, including cast-iron.

• Purchase high termperature paint from your local

retailer.

• Must use a high-temperature paint made speciﬁ -

cally for heating appliances.

a. Be sure the appliance is allowed to cool, has been

unplugged and the exhaust blower is off.

b. Remove the left side panel.

c. Remove the six screws holding the exhaust blower

motor to the housing and remove the motor. Using

caution as to not damage the gasket when removing

the blower. If damage occurs, install a new gasket

available as a replacement part.

d. Vacuum the blower’s impellers. Use care not to bend

or damage the blower ﬁ ns.

e. Using a brush or vacuum attachment, clean the inside

of the exhaust outlet.

f. Reattach the motor. Make sure the wires are attached

to the terminals on the the blower.

a. Be sure the appliance is allowed to cool and has been

unplugged.

b. Remove the right side panel.

c. Sweep or vacuum out any build-up on the impellers.

Use a brush or compressed air to loosen dirt if needed.

Avoid damaging the impellers.

4

Maintaining & Servicing Your Appliance

7077-171G • October 15, 2015 (877) 447- 476816

D. High Ash Fuel Content Maintenance

• Frequency: As needed

• By: Homeowner

Poor quality pellet fuel, lack of maintenance, or if the small

dial control is set to a less than optimum setting, poor com-

bustion conditions that make the ﬁ repot ﬁ ll quickly with ashes

and clinkers.

This condition makes the appliance susceptible to overﬁ lling

the ﬁ repot with pellets which may result in smoking, soot-

ing and possible hopper ﬁ res. The ﬁ gure below shows an

example where the ﬁ repot overﬁ lls, pellets back up into the

feed tube and ash has accumulated in the ﬁ rebox.

An inefﬁ cient and non-economical method of burning of fuel

caused by poor quality pellet fuel

is shown below.

If the ash buildup exceeds the half way point in the ﬁ repot

IMMEDIATE ATTENTION AND CLEANING IS REQUIRED.

Incorrect Flame Height

Tall, Lazy Flame

Orange in Color

Pellets Back-up in Feed Tube

Ash build-up in Firebox

Firepot Overfills

4

Maintaining & Servicing Your Appliance

[email protected] 7077-171G • October 15, 2015 17

E. Frequently Asked Questions

What causes my glass to become dirty?

If the glass has white ash build up it is normal and the

glass should be cleaned. If it is a black soot build up

airﬂ ow through the unit may be restricted. The most

often cause is overdue maintenance and cleaning. See

“Maintaining and Servicing Appliance” in the owner’s

manual and/or make adjustments to the trim control.

How can I get more heat out of the appliance?

The most often cause of diminished heat output is

overdue maintenance and cleaning . See “Maintaining

and Servicing Appliance” in the owner’s manual.

What should I do if I smell smoke or there is ash/

soot coming from the appliance?

While there will always be some smoke smell from

wood burning appliances (including pellet) you should

investigate all venting to make sure it is sealed prop-

erly. Most venting requires silicone to seal the seams.

In addition most homes are built very tight today and

with exhaust systems can create negative pressure

in the home. See “Negative Pressure” under “Getting

Started” in the owner’s manual if you have checked the

venting but still have smoke coming from the appli-

ance. For ash or soot check the above and the exhaust

blower housing and seals.

Why would my appliance run ﬁ ne last winter but

not start this fall?

It is possible that the stove was not properly prepared

for the Non-burn season. See “Troubleshooting” in the

owner’s manual.

Why would the metal on the inside of the appliance

begin to ﬂ ake?

There are some pellet mills that get their raw materials

from lumber mills that purchase logs that are trans-

ported in sea water. These pellets can have a higher

salt content and cause the metals in the unit to corrode

prematurely and deteriorate. If you are seeing any

components inside the ﬁ rebox deteriorate it is recom-

mended to change pellet brands immediately.

Is there a place to lubricate the blowers to quiet

them down?

The most often cause of noisy blowers is from the

impellers becoming dirty over time. See “General Main-

tenance & Cleaning” under “Maintaining & Servicing

Appliance” in the owner’s manual. No form of lubrica-

tion should ever need applied to the blowers.

What is the metal object with the bend in it for that

came inside the plastic bag?

It is a clean-out tool used to help clean the ﬁ repot and

remove any jams in the rare event they occur in the

feed tube.

Why is there a black residue building up on the

outside of my home?

Wind can cause this to happen. If the appliance is

operating correctly very little soot should ever exit the

termination cap. Also check to be sure the venting is

installed per the owner’s manual and local codes.

Do I need an outside air kit?

Outside air is required for mobile home installs and in

some jurisdictions. Refer to “Listing & Code Approv-

als”,“ Mobile Home Installation” and “ Appliance Set-up”

owner’s manual. Also refer to local building codes.

I am seeing sparks coming out of my pipe (termina-

tion cap) outside is this safe?

This is normal. As long as clearances to combustibles

were followed this is safe.

I have no power to anything. Does this unit have a

circuit breaker or fuse or a reset button?

This unit has one serviceable fuse on the control board

and a resetable snap switch mounted to the feed tube.

Can I burn corn in my unit?

NO, corn is not an approved fuel.

Where is the serial # of my unit is located?

The serial # is located on the back of the stove.

4

Maintaining & Servicing Your Appliance

7077-171G • October 15, 2015 (877) 447- 476818

1. Turn the dial control to the off position. Unplug the power

to the unit.

2. The convection blower is located in the rear of the unit.

3. Using #2 Phillips screwdriver, loosen the bolts on the

rear of the unit holding on the side panels. You do not

need to remove the screws. Remove side panels by

lifting up and out.

4. Unplug the wires from the convection blower motor from

the right side of the unit.

5. Remove the two screws holding the convection blower

housing to the sheet metal plenum. Using a slight

twisting motion, rotate the blower back and it will release.

A. Convection Blower Replacement

B. Exhaust Blower Replacement

1. Turn the dial control to the off position. Unplug the power

to the unit.

2.

Remove the left side panel by loosening the two or three

bolts in the rear of the unit.

3. Disconnect 2 white wires from the white and blue wires of

the exhaust blower.

4. Remove the blower motor attached to a removable plate

on the exhaust blower. Depending on the model, use

a 1/4 inch socket, or 1/4 inch Nut Driver or #2 Phillips

Head screw driver to loosen the 6 screws in the keyhole

shaped holes and rotate the plate. It is only necessary to

loosen screws.

5. Remove the exhaust blower and gasket.

6. Check for degradation on the gasket and replace if

necessary using the gasket included in the kit.

7. Re-install in reverse order.

Loosen Screws,

Do Not Remove

5

Replacement Parts

[email protected] 7077-171G • October 15, 2015 19

Power - Manual Reset

1. Turn the dial control to the off position. Unplug the power

to the unit.

2. Using #2 Phillips screwdriver, loosen the bolts on the rear

of the unit holding on the left side panel. You do not need

to remove the screws. Remove side panels by lifting up

and out.

3. Locate the snap disk on the top side of the feed tube

where it meets the hopper. Disconnect the wire leads

from the snap disk.

4. Using a #1 Phillips screwdriver, remove two 6-32 fasten-

ers retaining the snap disk onto the side of the feed tube.

5. Using the same fasteners, attach the new snap disk.

Attach the wire leads.

6. Restore power.

C. Snap Disc Replacement

D. Igniter Replacement

1. Turn the dial control to the off position. Unplug the

power to the unit.

2. Unplug the wire leads to the igniter.

3. Remove the screw in the side of the igniter chamber.

Pinch the ends of the bracket together and pull the

igniter straight out of the igniter chamber.

4. If there is difﬁ culty in removing the igniter from the

chamber, the chamber can be removed from the rear

of the ﬁ rebox by removing the the 1/4-20 bolt.

5. Re-install the new igniter into the chamber using the

bracket.

6. Inspect the igniter from the front of the unit by removing

the ﬁ repot and looking into the end of the chamber.

MAKE SURE THE IGNITER IS CENTERED IN THE

CHAMBER.

E. Bafﬂ e Removal & Replacement

1. Turn the dial control to the off position. Make sure the

unit is cool.

2. Remove the center bafﬂ e ﬁ rst by using the handle at

the top of the bafﬂ e and pull up and then towards you.

The hooks on the bafﬂ e will slide out of the slots in the

bracket.

3

. Remove the left bafﬂ e and then the right bafﬂ e by pulling

up and then towards you. The left and right bafﬂ es have

similar hooks and slots.

5

Replacement Parts

7077-171G • October 15, 2015 (877) 447- 476820

F. Glass Replacement

• Glass is 5mm thick high temperature heat-

resistant ceramic glass.

• DO NOT REPLACE with any other material.

• Alternate material may shatter and cause

injury.

WARNING

1. Open the door from the appliance by lifting door off of

hinge pins and lay on a ﬂ at surface face down.

2. Using a Phillips Head screw driver, remove the 3

brackets and set aside.

3. Remove old glass and replace with the new glass.

4. Re-install the brackets using the same screws.

G. Control Board Replacement

1. Turn the dial control to the off position. Unplug the

power to the unit.

2. Unplug the wires from the control board. The connectors

are locking connectors. Pinch the release tab on each

connector and gently tug and rock loose.

3. Pinch the 4 plastic pins from the rear of the unit to

release the control board connectors.

4. Install new board following the steps in reverse.

H. Fuse Replacement

1. Turn the dial control to the off position. Unplug the

power to the unit.

2. Pull the plastic fuse holder cover off the control board.

3. Replace fuse with 5AMP 120VAC fuse only.

4. Replace the cover on the fuse holder and restart unit.

I. Feed Motor Replacement

1. Turn the dial control to the off position and unplug the

unit. Remove the right side panel and feed motor cover

plate in the rear of the unit.

2. Unplug the connector from the feed motor.

3. Using pliers, remove the cotter pin.

4. Remove the feed motor from the feed shaft.

5. Reinstall the new feed motor by aligning the clearance

hole in the feed motor shaft with the auger spring shaft.

6. Plug the feed motor leads back in and restore power.

J. Feed Spring Replacement

1. Empty the hopper of all pellets. then follow the steps to

remove the feed motor above.

2. Remove the four screws holding the feed motor bracket

on.

3. Slide the auger assembly out from the bottom in the

rear of the unit.

4. Inspect the bronze bearings, replace if needed.

5. Install new spring assembly following reverse steps

including reattaching the feed motor.

5

Replacement Parts

La page charge ...

Pleasant Hearth PH50PS Series Le manuel du propriétaire

Ce manuel convient également à

Pleasant Hearth PH50PS Series Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents