Wacker Neuson E3000 Manuel utilisateur

Operator’s Manual

Notice d'emploi

Hydronic Surface Heater

Réchauffeur hydronique de surface

E3000

Type E3000

Document 5100024483

Date

0719

Version

05

Language EN-FR

5100024483

Copyright notice

All rights, including copying and distribution rights, are reserved.

This publication may be photocopied by the original purchaser of the

machine. Any other type of reproduction is prohibited without express

written permission from Wacker Neuson Production Americas LLC.

Any type of reproduction or distribution not authorized by Wacker

Neuson Production Americas LLC represents an infringement of valid

copyrights. Violators will be prosecuted.

Trademarks

All trademarks referenced in this manual are the property of their

respective owners.

Manufacturer

Wacker Neuson Production Americas LLC

N92W15000 Anthony Avenue

Menomonee Falls, WI 53051 U.S.A.

Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957

www.wackerneuson.com

Original instructions

This Operator’s Manual presents the original instructions. The original

language of this Operator’s Manual is American English.

wc_tx004643en.fm 3

CALIFORNIA Proposition 65 Warning

WARNING

The engine exhaust from this product contains chemicals known to the State of

California to cause cancer, birth defects, or other reproductive harm.

WARNING

Diesel engine exhaust and some of its constituents are known to the State of

California to cause cancer, birth defects, and other reproductive harm.

WARNING

Cancer and Reproductive Harm -

www.P65Warnings.ca.gov.

WARNING

Batteries, battery posts, terminals and related accessories contain lead and lead

compounds, and other chemicals known to the State of California to cause cancer

and birth defects or other reproductive harm. WASH HANDS AFTER HANDLING.

CALIFORNIA Proposition 65 Warning Proposition 65 Warning

4 wc_tx004643en.fm

This page is intentionally left blank.

wc_tx004220gb_FM10.fm

5

E3000 Foreword

Foreword

This heater is designed and approved for use as a construction heater in

accordance with Standard ANSI Z83.7–CSGA 2.14. CHECK WITH YOUR LOCAL

FIRE SAFETY AUTHORITY IF YOU HAVE QUESTIONS ABOUT APPLICATIONS.

Other standards govern the use of fuel gases and heat producing products in

specific applications. Your local authority can advise you about these.

THE INSTALLATION OF THE UNIT SHALL BE IN ACCORDANCE WITH THE

REGULATIONS OF THE AUTHORITIES HAVING JURISDICTION.

WARNING

Risk of personal injury or machine damage from improper use.

► Before using the machine, read and understand all instructions and follow them

carefully.

► The manufacturer is not responsible for damages to goods or persons due to

improper use of this machine.

WARNING

Failure to comply with the precautions and instructions provided with this machine

can result in death, serious injury, and property loss or damage from fire, explosion,

burns, asphyxiation, carbon monoxide poisoning, and/or electric shock.

► Before using the machine, read and understand all precautions and instructions

that have been provided. Follow them carefully.

► Only persons who can understand and follow the precautions and instructions

should use or service this machine.

► Contact the manufacturer if you need assistance with operating the machine or

need replacement manuals or labels.

WARNING

Work site fire, burn, inhalation, and explosion hazards.

► This machine is not designed to be used in explosion-proof applications. Keep

solid combustibles, such as building materials, paper, or cardboard at a safe

distance away from the machine.

► Never use this machine in applications which do or may contain volatile or

airborne combustibles (e.g natural gas fumes), or products such as gasoline,

solvents, paint thinner, dust particles, or unknown chemicals.

wc_tx004220gb_FM10.fm

6

Foreword E3000

SAVE THESE INSTRUCTIONS—This manual contains important instructions for

the machine models below. These instructions have been written expressly by

Wacker Neuson Production Americas LLC and must be followed during installation,

operation, and maintenance of the machines.

Machine

documentation

■ From this point forward in this documentation, Wacker Neuson Production

Americas LLC will be referred to as Wacker Neuson.

■ Keep a copy of the Operator’s Manual with the machine at all times.

■ For spare parts information, please see your Wacker Neuson Dealer, or visit the

Wacker Neuson website at http://www.wackerneuson.com/.

■ When ordering parts or requesting service information, be prepared to provide

the machine model number, item number, revision number, and serial number.

Expectations

for

information in

this manual

■ This manual provides information and procedures to safely operate and

maintain the above Wacker Neuson model(s). For your own safety and to

reduce the risk of injury, carefully read, understand, and observe all instructions

described in this manual.

■ Wacker Neuson expressly reserves the right to make technical modifications,

even without notice, which improve the performance or safety standards of its

machines.

■ The information contained in this manual is based on machines manufactured

up until the time of publication. Wacker Neuson reserves the right to change any

portion of this information without notice.

■ The illustrations, parts, and procedures in this manual refer to Wacker Neuson

factory-installed components. Your machine may vary depending on the

requirements of your specific region.

WARNING

Not for use in homes or recreational vehicles. Installing this machine in a home or

RV may result in fire, explosion, property damage, personal injury, or death.

► Operate the machine only as specified in the topic Machine Description and

Intended Use.

Machine

(G = Generator, LB = Lift Bail, TC = Trans

Canada Tank)

Item Number Revision

E3000 LB 5000620678 225 and higher

E3000G (3KW), TC 5100017807 100 and higher

E3000G (3KW), LB, TC 5100017809 100 and higher

E3000G (6KW), LB, TC 5100025046 001 and higher

wc_tx004220gb_FM10.fm

7

E3000 Foreword

CALIFORNIA

Proposition

65 Warning

Combustion exhaust, some of its constituents, and certain vehicle components

contain or emit chemicals known to the State of California to cause cancer and

birth defects or other reproductive harm.

Laws

pertaining to

spark

arresters

NOTICE: State Health Safety Codes and Public Resources Codes specify that in

certain locations spark arresters be used on internal combustion engines that use

hydrocarbon fuels. A spark arrester is a device designed to prevent accidental

discharge of sparks or flames from the engine exhaust. Spark arresters are

qualified and rated by the United States Forest Service for this purpose. In order to

comply with local laws regarding spark arresters, consult the engine distributor or

the local Health and Safety Administrator.

Manufacturer’s

approval

This manual contains references to approved parts, attachments, and

modifications. The following definitions apply:

■ Approved parts or attachments are those either manufactured or provided by

Wacker Neuson.

■ Approved modifications are those performed by an authorized Wacker

Neuson service center according to written instructions published by Wacker

Neuson.

■ Unapproved parts, attachments, and modifications are those that do not

meet the approved criteria.

Unapproved parts, attachments, or modifications may have the following

consequences:

■ Serious injury hazards to the operator and persons in the work area

■ Permanent damage to the machine which will not be covered under warranty

Contact your Wacker Neuson dealer immediately if you have questions about

approved or unapproved parts, attachments, or modifications.

wc_tx004220gb_FM10.fm

8

Foreword E3000

This page is intentionally left blank.

Table of Contents

E3000

wc_bo5100024480_05TOC.fm

9

CALIFORNIA Proposition 65 Warning 3

Foreword 5

1 Safety Information 13

1.1 Signal Words Used in this Manual ..................................................... 13

1.2 Machine Description and Intended Use ............................................. 14

1.3 Safety Guidelines for Operating the Machine ..................................... 15

1.4 Safety Guidelines for Lifting the Machine ........................................... 16

1.5 Safety Guidelines for Operating Combustion Burners ....................... 17

1.6 Safety Guidelines for Operating Generators ...................................... 18

1.7 Service Safety .................................................................................... 20

1.8 Safety Guidelines for Towing the Machine ......................................... 22

1.9 Reporting Safety Defects ................................................................... 23

2 Labels 24

2.1 Label Locations .................................................................................. 24

2.2 Label Meanings .................................................................................. 26

3 Lifting and Transporting 35

3.1 Lifting the Machine ............................................................................. 35

3.2 Preparing the Machine for Transport on a Truck or Trailer ................ 36

3.3 Transporting the Machine on a Truck or Trailer ................................. 37

3.4 Before Towing Checklist ..................................................................... 39

3.5 Towing the Machine ........................................................................... 40

3.6 Testing the Breakaway System—Electric Brakes .............................. 41

3.7 Hazardous Materials Placards ........................................................... 43

4 Operation 44

4.1 External Components ......................................................................... 44

4.2 Internal Components .......................................................................... 45

4.3 Rear Components .............................................................................. 46

4.4 Pumps, Gauges, and Valves .............................................................. 47

4.5 Control Panel ...................................................................................... 48

4.6 Control Panel Components ................................................................ 49

4.7 Preparing the Machine for First Use ................................................... 50

4.8 Breaking in the Generator .................................................................. 50

4.9 General Sequence of Operation ......................................................... 51

Table of Contents

E3000

wc_bo5100024480_05TOC.fm

10

4.10 Checking the HTF Level ......................................................................52

4.11 Recommended Fuels and Fuel Blending Guide ..................................53

4.12 Refueling the Machine .........................................................................54

4.13 Positioning the Machine ......................................................................55

4.14 Before Starting Checks .......................................................................57

4.15 Starting, Operating, and Stopping—Machines with Generators ..........60

4.16 Starting, Operating, and Stopping—Machines without Generators .....65

4.17 Preheating the HTF .............................................................................68

4.18 Initiating HTF Flow ..............................................................................69

4.19 Setting the Operating Temperature .....................................................70

4.20 Unwinding and Positioning the Hoses .................................................71

4.21 Hose Spacing Guidelines ....................................................................72

4.22 Monitoring the Operating Parameters .................................................73

4.23 Rewinding the Hoses ..........................................................................74

4.24 Resetting a Low HTF Fault ..................................................................76

4.25 Quick-Connect Coupling Usage and Care ..........................................79

4.26 Operating States of the Beckett Burner Controller ..............................80

5 Accessories 86

5.1 Available Accessories .........................................................................86

5.2 Expanding the Surface Heating Capacity ............................................87

5.3 Expanded Operation Using One HHS3002 and One DPP ..................88

5.4 Expanded Operation Using Two HHS3002 and Two DPP ..................90

5.5 Mounting and Connecting the Auxiliary Pump Panel ..........................93

5.6 Using Heat Exchangers to Heat Air .....................................................95

5.7 Connecting Six HX50 Heat Exchangers ..............................................96

5.8 Connecting Five HX50 Heat Exchangers ............................................98

5.9 Connecting Four HX50 Heat Exchangers .........................................100

5.10 Connecting Three HX50 Heat Exchangers .......................................102

5.11 Connecting Two HX50 Heat Exchangers ..........................................104

5.12 Connecting One HX50 Heat Exchanger ............................................106

5.13 Connecting Three HX100 Heat Exchangers .....................................108

5.14 Connecting Two HX100 Heat Exchangers ........................................110

5.15 Connecting One HX100 Heat Exchanger ..........................................112

5.16 Connecting Two HX200 Heat Exchangers ........................................114

5.17 Connecting One HX200 Heat Exchanger ..........................................116

6 Burner Setup—Oil 117

6.1 Factory Settings ................................................................................117

6.2 Setting up the Burner ........................................................................117

Table of Contents

E3000

wc_bo5100024480_05TOC.fm

11

6.3 Setting and Checking the Electrodes ............................................... 120

6.4 Replacing the Burner Nozzle ............................................................ 122

6.5 Setting the “Z” Distance .................................................................... 124

6.6 Adjusting the Air Settings ................................................................. 126

6.7 Adjusting the Fuel Pressure ............................................................. 127

7 Burner Setup—Gas 128

7.1 Factory Settings ............................................................................... 128

7.2 Restrictions for Connecting the Gas Supply ..................................... 129

7.3 Setting up the Burner ....................................................................... 130

7.4 Removing and Installing the Combustion Head ............................... 132

7.5 Adjusting the Ionization Probe and the Electrode ............................ 134

7.6 Changing the Burner Orifice ............................................................. 135

7.7 Changing the Burner Diaphragm ...................................................... 136

7.8 Checking and Adjusting the Air Damper (Gate) Setting ................... 137

7.9 Adjusting the Combustion Head ....................................................... 138

7.10 Checking the Supply Gas Pressure ................................................. 139

7.11 Checking and Adjusting the Burner Gas Pressure ........................... 141

8 Maintenance 143

8.1 Periodic Maintenance Schedule ....................................................... 143

8.2 Inspecting the HTF System and the Fuel System ............................ 144

8.3 Repairing a Hose .............................................................................. 145

8.4 Inspecting the Electrical Components .............................................. 147

8.5 Filling the HTF Expansion Tank ....................................................... 149

8.6 Cleaning the HTF Strainer ................................................................ 151

8.7 Replacing the Fuel Filter .................................................................. 153

8.8 Lubricating the Hose Reel System ................................................... 154

8.9 Cleaning the Turbulators and the Exhaust Ducting .......................... 155

8.10 Inspecting and Replacing the Rope Gasket ..................................... 157

8.11 Removing the Oil Burner .................................................................. 158

8.12 Installing the Burner ......................................................................... 159

8.13 Storing the Machine ......................................................................... 160

8.14 Storing the Generator ....................................................................... 161

8.15 Preparing the Machine for Seasonal Operation ............................... 162

8.16 Connecting and Maintaining the Battery .......................................... 163

9 Generator Maintenance 164

9.1 Generator Load Banking Procedure ................................................. 166

Table of Contents

E3000

wc_bo5100024480_05TOC.fm

12

10 Troubleshooting 168

10.1 Troubleshooting the Machine ............................................................168

10.2 Troubleshooting the Oil Burner .........................................................169

10.3 Troubleshooting the Gas Burner .......................................................170

10.4 Troubleshooting the Generator .........................................................171

11 Technical Data 175

11.1 Machine .............................................................................................175

11.2 Trailer ................................................................................................176

11.3 Dimensions ........................................................................................176

12 MSDS: Dowfrost HD 50 177

13 Fuji Temperature Controller 184

14 Tire Safety Information 187

15 Schematics 199

15.1 Composite Schematic—Machine with Oil Burner ..............................199

15.2 Composite Schematic—Machine with Gas Burner ...........................200

15.3 Electrical Schematic Components .....................................................201

15.4 Circulation System Circuit .................................................................204

15.5 Rewind System Circuit ......................................................................205

15.6 3kW Generator—AC Schematic ........................................................206

15.7 3kW Generator—AC Schematic Components ..................................207

15.8 6kW Generator—AC Schematic ........................................................208

15.9 6kW Generator—AC Schematic Components ..................................209

15.10 Generator—DC Schematic: 6kW ......................................................210

15.11 Generator—DC Schematic Components: 6kW .................................211

15.12 Generator—DC Schematic: 3kW ......................................................212

15.13 Generator—DC Schematic: 3kW ......................................................213

15.14 Gas Train Schematic .........................................................................214

15.15 Trailer Plug—Wiring Diagram ............................................................215

15.16 Trailer Lights and Brakes—Wiring Diagram ......................................216

15.17 Trailer Lights and Brakes—Components ..........................................217

15.18 Trailer Junction Box—Wiring Diagram ..............................................217

wc_si000579gb_FM10.fm

13

E3000 Safety Information

1 Safety Information

1.1 Signal Words Used in this Manual

This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE

signal words which must be followed to reduce the possibility of personal injury,

damage to the equipment, or improper service.

NOTICE: Used without the safety alert symbol, NOTICE indicates a situation

which, if not avoided, could result in property damage.

Note: A Note contains additional information important to a procedure.

This is the safety alert symbol. It is used to alert you to potential personal hazards.

► Obey all safety messages that follow this symbol.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

► To avoid death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

► To avoid possible death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

► To avoid possible minor or moderate injury from this type of hazard, obey all

safety messages that follow this signal word.

wc_si000579gb_FM10.fm

14

Safety Information E3000

1.2 Machine Description and Intended Use

This machine is a hydronic surface heater. The Wacker Neuson Hydronic Surface

Heaters consist of a trailer-mounted enclosure that houses an optional diesel

generator, a hydronic heater, electric motors, fixed pump(s) and plumbing, a diesel

(or gas) burner, a fuel tank, and a hose handling system.

The hydronic heating system utilizes a burner that indirectly warms the Heat

Transfer Fluid (HTF). The warmed HTF is continuously circulated through a

vented, closed loop hose system. A positive displacement pump pushes the

warmed HTF through the hose system, thereby radiating and transferring the heat

to the required application area.

An insulated blanket may be laid over the hoses to increase efficiency. The low

HTF level protection device shuts down the machine if the HTF level drops below

minimum operational capacity.

This machine is intended to be used as a surface heater in order to thaw frozen

ground, to cure concrete, or to prevent frost and freezing. In addition, when used

with other Wacker Neuson accessories, this machine can be used to heat air.

This machine has been designed and built strictly for the intended use(s) described

above. Using the machine for any other purpose could permanently damage the

machine or seriously injure the operator or other persons in the area. Machine

damage caused by misuse is not covered under warranty.

The following are some examples of misuse:

■ Using the machine to heat anything other than what is stated above

■ Using the machine to pump anything other than the factory recommended Heat

Transfer Fluid

■ Using the generator (if equipped) to power anything other than the machine

itself or Wacker Neuson accessory machines, as instructed in the Operator's

Manual

■ Using the machine as a ladder, support, or work surface

■ Using the machine to carry or transport passengers or equipment

■ Using the machine to tow other machines

■ Operating the generator (if equipped) in a manner that is inconsistent with all

federal, state, and local codes and regulations

■ Operating the machine outside of factory specifications

■ Operating the machine in a manner inconsistent with all warnings found on the

machine and in the Operator’s Manual

This machine has been designed and built in accordance with the latest global

safety standards. It has been carefully engineered to eliminate hazards as far as

practicable and to increase operator safety through protective guards and labeling.

However, some risks may remain even after protective measures have been taken.

They are called residual risks. On this machine, they may include exposure to:

■ Heat, noise, and exhaust from the engine or hydronic heater

■ Burns from the HTF or radiant heat from the hoses

wc_si000579gb_FM10.fm

15

E3000 Safety Information

■ Fire hazards from improper refueling techniques

■ Fuel and its fumes

■ Personal injury from improper lifting of the trailer tongue

■ Tripping hazards from the hoses

To protect yourself and others, make sure you thoroughly read and understand the

safety information presented in this manual before operating the machine.

1.3 Safety Guidelines for Operating the Machine

Operator

training

Before operating the machine:

■ Read and understand the operating instructions contained in all manuals

delivered with the machine.

■ Familiarize yourself with the location and proper use of all controls and safety

devices.

■ Contact Wacker Neuson for additional instruction and training if necessary.

When operating this machine:

■ Do not allow improperly trained people to operate the machine. People

operating the machine must be familiar with the potential risks and hazards

associated with it.

Operator

qualifications

Only trained personnel are permitted to start, operate, and shut down the machine.

They also must meet the following qualifications:

■ Have received instruction on how to properly use the machine

■ Are familiar with required safety devices

The machine must not be accessed or operated by:

■Children

■ People impaired by alcohol, drugs, or prescription drugs

Machine

condition

Only operate the machine when:

■ All safety devices and guards are in place and in working order.

■ All controls operate correctly.

■ The machine is set up correctly according to the instructions in the Operator’s

Manual.

■ The machine is clean, free of debris and combustible materials.

■ The machine’s labels are legible.

When operating the machine:

■ Do not modify or defeat the safety devices.

■ Do not use worn electrical cords.

■ Do not use faulty fuel supplies.

wc_si000579gb_FM10.fm

16

Safety Information E3000

Safe

operating

practices

When operating this machine:

■ Remain aware of the machine’s moving parts. Keep hands, feet, and loose

clothing away from the machine’s moving parts.

■ Do not operate a machine in need of repair.

Personal

protective

equipment

(PPE)

Wear the following personal protective equipment (PPE) while operating this

machine:

■ Close-fitting work clothes that do not hinder movement

■ Safety glasses with side shields

■ Hearing protection

■ Safety-toed footwear

Work space

When operating the machine:

■ Position the machine on a firm, noncombustible, level surface, and chock the

wheels.

■ Position the machine on the job site so that neither it nor the operator are

standing in water.

■ Keep the area immediately surrounding and underneath the machine clean,

neat, and free of debris and combustible materials.

■ Keep the area above the machine clear of debris that could fall on the machine.

■ Store the machine properly when it is not being used.

■ Keep unauthorized personnel, children, and pets away from the machine.

When operating the machine:

■ Never operate the machine in areas that contain flammable objects, fuels, or

products that produce flammable vapors.

1.4 Safety Guidelines for Lifting the Machine

When lifting the machine:

■ Make sure slings, chains, hooks, ramps, jacks, forklifts, cranes, hoists, and any

other type of lifting device used is attached securely and has enough weight-

bearing capacity to lift or hold the machine safely. See the Technical Data

chapter for machine weight.

■ Remain aware of the location of other people when lifting the machine.

■ Only use the lifting points and tie-downs described in the Operator’s Manual.

■ Make sure the transporting vehicle has sufficient load capacity and platform size

to safely transport the machine.

To reduce the possibility of injury:

■ Do not stand under the machine while it is being lifted or moved.

■ Do not get onto the machine while it is being lifted or moved.

wc_si000579gb_FM10.fm

17

E3000 Safety Information

1.5 Safety Guidelines for Operating Combustion Burners

When using the machine:

■ Clean up any spilled fuel immediately.

■ Replace the fuel tank cap after refueling the machine.

■ Refill the fuel tank in a well-ventilated area.

■ Shut down the generator, if equipped, when refueling.

When using the machine:

When refueling the machine:

■ Do not fill or drain the fuel tank near an open flame or while the machine is

running.

■ Do not smoke when refueling the machine.

■ Do not use gasoline, crankcase oil, or any oil containing gasoline.

DANGER

Exhaust gas from the burner contains carbon monoxide, a deadly poison. Exposure

to carbon monoxide can kill you in minutes.

► NEVER operate the machine inside an enclosed area, such as a tunnel, inside

a building or holding tank unless adequate ventilation is provided through items

such as exhaust fans or hoses.

wc_si000579gb_FM10.fm

18

Safety Information E3000

1.6 Safety Guidelines for Operating Generators

This machine is built with user safety in mind; however, like any electrical device it

can present serious hazards if improperly operated and serviced. Follow

instructions carefully. Should questions arise during operation or service of this

equipment, contact your Wacker Neuson dealer.

General

precautions

■ Keep a multi-class, type ABC or equivalent fire extinguisher at hand when using

the generator. Refer to NFPA No. 10 for further information regarding fire

extinguishers.

■ Do not use evaporative starting fluids. They are highly explosive.

■ Do not store items such as excess oil, oil rags, tools within the generator

compartment. Items stored within the generator compartment are a fire hazard

and can restrict cooling air.

■ Wash skin thoroughly after exposure to used engine oil.

DANGER

Carbon monoxide. Using a generator indoors CAN KILL YOU IN MINUTES.

Generator exhaust contains carbon monoxide (CO). This is a poison you cannot

see or smell. If you can smell the generator exhaust, you are breathing CO. But

even if you cannot smell the exhaust, you could be breathing CO.

WARNING

Electrocution hazard. Generators present special hazards during operation and

servicing. These include the risk of electrocution or severe electrical shock. Failure

to follow the safety information below can result in severe injury or death.

► Read and follow the safety instructions in this Operator’s Manual.

► Contact the generator manufacturer for additional information regarding the

generator.

WARNING

Internal combustion engines present special hazards during operation and fueling.

Failure to follow the warnings and safety instructions could result in severe injury or

death.

► Read and follow the safety instructions in this Operator’s Manual.

► Contact the generator manufacturer for additional information regarding the

generator.

WARNING

Most used oil contains small amounts of materials that can cause cancer and other

health problems if inhaled, ingested, or left in contact with skin for prolonged

periods of time.

► Take steps to avoid inhaling or ingesting used engine oil.

► Wash skin thoroughly after exposure to used engine oil.

wc_si000579gb_FM10.fm

19

E3000 Safety Information

Before

operating the

generator

■ Know how to start, operate, and stop the generator before starting it.

■ Obtain the proper training for operating the generator. Do not allow untrained

personnel to operate or service the generator.

■ Check the fuel lines and the fuel tank for leaks and cracks before starting the

engine.

■ Clean the generator of any spilled fuel.

Running the

generator

■ Do not start the engine if fuel has spilled or a fuel odor is present.

■ Keep the area around the exhaust pipe free of flammable materials.

■ Do not smoke while operating the generator.

■ Keep sparks, flames, electrical arcs, and other sources of ignition far away from

the generator.

■ Do not touch the engine or muffler while the engine is running or immediately

after it has been turned off.

■ Do not overload the generator. The total amperage of the tools and equipment

attached to the generator must not exceed the load rating of the generator.

■ Do not operate the generator with wet hands.

■ Do not remove the radiator cap when the generator is running or is hot.

Refueling

safety

When adding fuel to the fuel tank:

■ Do not smoke.

■ Do not refuel a hot or running engine.

When adding fuel to the fuel tank:

■ Keep sparks, flames, electrical arcs, and other sources of ignition far away from

the generator.

■ Refill the fuel tank only in a well-ventilated area.

■ Re-install the fuel tank cap after refueling.

Maintenance

safety

■ Only a trained technician should attempt to repair the generator.

■ Test procedures which require that the generator be running must be performed

using extreme caution.

■ Make sure clothing and shoes are dry, stand on a dry wooden platform or rubber

insulating mat, and use tools with insulated handles when servicing the

generator.

■ Engine antifreeze is toxic to humans and animals. Clean up spills and dispose

of used engine antifreeze in accordance with local environmental regulations.

■ Make sure all fasteners are secure and torqued properly.

wc_si000579gb_FM10.fm

20

Safety Information E3000

1.7 Service Safety

Service

training

Before servicing or maintaining the machine:

■ Read and understand the instructions contained in all manuals delivered with

the machine.

■ Familiarize yourself with the location and proper use of all controls and

protective devices.

■ Only trained personnel shall troubleshoot or repair problems occurring with the

machine.

■ Contact Wacker Neuson for additional training if necessary.

When servicing or maintaining this machine:

■ Do not allow untrained or improperly trained people to service or maintain the

machine. Personnel servicing or maintaining the machine must be familiar with

the associated potential risks and hazards.

Precautions

When servicing or maintaining the machine:

■ Read and understand the service procedures before performing any service to

the machine.

■ All adjustments and repairs must be completed before operating the machine.

Do not operate the machine with a known problem or deficiency.

■ All repairs and adjustments shall be completed by a qualified technician.

■ Turn off the machine before performing maintenance or making repairs.

■ Remain aware of the machine’s moving parts. Keep hands, feet, and loose

clothing away from the machine’s moving parts.

■ Reinstall the safety devices and guards after repair and maintenance

procedures are complete.

Machine

modifications

When servicing or maintaining the machine:

■ Use only accessories/attachments that are approved by Wacker Neuson.

■ Do not defeat safety devices.

■ Do not modify the machine without the express written approval of Wacker

Neuson.

Replacing

parts and

labels

■ Replace worn or damaged components.

■ Replace all missing and hard-to-read labels.

■ When replacing electrical components, use components that are identical in

rating and performance to the original components.

■ When replacement parts are required for this machine, use only Wacker

Neuson replacement parts or those parts equivalent to the original in all types of

specifications, such as physical dimensions, type, strength, and material.

Cleaning

When cleaning and servicing the machine:

■ Keep machine clean and free of debris such as leaves, paper, cartons, etc.

■ Keep labels legible.

La page charge ...

Wacker Neuson E3000 Manuel utilisateur

Wacker Neuson E3000 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents