ATEN KH2516A Manuel utilisateur

KVM Switch

KH2508A / KH2516A

User Manual

www.aten.com

KH2508A / KH2516A User Manual

ii

EMC Information

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE

STATEMENT: This equipment has been tested and found to comply with the

limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in

a residential area is likely to cause harmful interference in which case the user

will be required to correct the interference at his own expense.

The device complies with Part 15 of the FCC Rules. Operation is subject to

the following two conditions: (1) this device may not cause harmful interfer

-

ence, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority to operate this

equipment.

Warning: Operation of this equipment in a residential environment could

cause radio interference.

Achtung: Der Gebrauch dieses Geräts in Wohnumgebung kann Funkstörun-

gen verursachen.

Suggestion: Shielded twisted pair (STP) cables must be used with the unit to

ensure compliance with FCC & CE standards.

KCC Statement

RoHS

This product is RoHS compliant.

KH2508A / KH2516A User Manual

iii

User Information

Online Registration

Be sure to register your product at our online support center:

Telephone Support

For telephone support, call this number:

User Notice

All information, documentation, and specifications contained in this manual

are subject to change without prior notification by the manufacturer. The

manufacturer makes no representations or warranties, either expressed or

implied, with respect to the contents hereof and specifically disclaims any

warranties as to merchantability or fitness for any particular purpose. Any of

the manufacturer's software described in this manual is sold or licensed as is.

Should the programs prove defective following their purchase, the buyer (and

not the manufacturer, its distributor, or its dealer), assumes the entire cost of all

necessary servicing, repair and any incidental or consequential damages

resulting from any defect in the software.

The manufacturer of this system is not responsible for any radio and/or TV

interference caused by unauthorized modifications to this device. It is the

responsibility of the user to correct such interference.

The manufacturer is not responsible for any damage incurred in the operation

of this system if the correct operational voltage setting was not selected prior

to operation. PLEASE VERIFY THAT THE VOLTAGE SETTING IS

CORRECT BEFORE USE.

International http://eservice.aten.com

International 886-2-8692-6959

China 86-400-810-0-810

Japan 81-3-5615-5811

Korea 82-2-467-6789

North America 1-888-999-ATEN ext 4988

1-949-428-1111

KH2508A / KH2516A User Manual

iv

Package Contents

The KH2508A / KH2516A package consists of:

1 KH2508A or KH2516A Cat 5 High-Density KVM Switch

1 Firmware Upgrade Cable

1Power Cord

1 Rack Mount Kit

1 Foot Pad Set (4 pcs.)

1 User Instructions*

Check to make sure that all of the components are present and in good order.

If anything is missing, or was damaged in shipping, contact your dealer.

Read this manual thoroughly and follow the installation and operation

procedures carefully to prevent any damage to the switch or to any other

devices on the KH2508A / KH2516A installation.

* Features may have been added to the KH2508A / KH2516A since this

manual was published. Please visit our web site to download the most up-to-

date version of the manual.

Manual Date:2020-11-26

All other brand names and trademarks are the registered property of their respective owners.

KH2508A / KH2516A User Manual

v

Contents

EMC Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

RoHS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

Online Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

Telephone Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

User Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viii

Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix

Product Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix

Chapter 1.

Introduction

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Consoles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Computers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

KVM Adapter Cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Operating Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

KH2508A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

KH2516A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

KH2508A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

KH2516A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Chapter 2.

Hardware Setup

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Before you Begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Stacking and Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Stacking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Single Station Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Daisy Chaining . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Chapter 3.

Basic Operation

Port Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

OSD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Hotkey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Hot Plugging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

KH2508A / KH2516A User Manual

vi

Hot Plugging Stations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Hot Plugging KVM Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Hot Plugging Console Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Powering Off and Restarting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Port ID Numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Chapter 4.

OSD Operation

OSD Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

OSD Hotkey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

OSD Login. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Manufacturing Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

OSD Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

OSD Main Screen Headings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

OSD Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

F1: GOTO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

F2: LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

F3: SET. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

F4: ADM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

F5: SKP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

F6: BRC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

F7: SCAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

F8: LOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Chapter 5.

Hotkey Operation

Hotkey Port Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Invoking Hotkey Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Number Lock and Minus Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Control and F12 Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Hotkey Mode Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Exiting Hotkey Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Selecting the Active Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Auto Scan Mode Switching. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Setting the Scan Interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Invoking Auto Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Exiting Auto Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Skip Mode Switching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Entering Skip Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Exiting Skip Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Computer Keyboard / Mouse Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Setting the Hotkey Beeper ON/OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Setting the Hotkey key combination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Setting the OSD Hotkey combination . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Setting the Port Operating System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Restore the Default Values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Hotkey Summary Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

KH2508A / KH2516A User Manual

vii

Chapter 6.

Keyboard Emulation

Mac Keyboard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Sun Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50

Chapter 7.

The Firmware Upgrade Utility

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Performing the Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Starting the Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Upgrade Succeeded . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Upgrade Failed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57

Firmware Upgrade Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Main Board and OSD Firmware Upgrade Recovery . . . . . . . . . . . 57

Adapter Cable Firmware Upgrade Recovery. . . . . . . . . . . . . . . . .58

OSD Configuration Backup/Restore . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59

Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59

Restore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60

Appendix

Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63

Consignes de sécurité. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Général . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Montage sur bâti . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

International. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

North America . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Connection Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71

KH2508A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

KH2516A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Compatible Products. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

OSD Factory Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Administrator Login Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

KH2508A / KH2516A User Manual

viii

About This Manual

This User Manual is provided to help you get the most from your KH2508A /

KH2516A system. It covers all aspects of installation, configuration and

operation. An overview of the information found in the manual is provided

below.

Chapter 1, Introduction, introduces you to the KH2508A / KH2516A

system. Its purpose, features and benefits are presented, and its front and back

panel components are described.

Chapter 2, Hardware Setup, describes how to set up your installation. The

necessary steps – from a basic single stage hookup to a complete daisy-chained

operation are provided.

Chapter 3, Basic Operation, explains the fundamental concepts involved

in operating the KH2508A / KH2516A.

Chapter 4, OSD Operation, provides a complete description of the

KH2508A / KH2516A's OSD (On Screen Display), and how to work with it.

Chapter 5, Hotkey Operation, details all of the concepts and procedures

involved in the keyboard hotkey operation of your KH2508A / KH2516A

installation.

Chapter 6, Keyboard Emulation, provides tables that list the PC to Mac

and PC to Sun keyboard emulation mappings.

Chapter 7, The Firmware Upgrade Utility, explains how to upgrade the

KH2508A / KH2516A's firmware with the latest available versions.

An Appendix, provides specifications and other technical information

regarding the KH2508A / KH2516A.

KH2508A / KH2516A User Manual

ix

Conventions

This manual uses the following conventions:

Product Information

For information about all ALTUSEN products and how they can help you

connect without limits, visit ALTUSEN on the Web or contact an ALTUSEN

Authorized Reseller. Visit ALTUSEN on the Web for a list of locations and

telephone numbers:

Monospaced Indicates text that you should key in.

[ ] Indicates keys you should press. For example, [Enter]

means to press the Enter key. If keys need to be chorded,

they appear together in the same bracket with a plus sign

between them: [Ctrl+Alt].

1. Numbered lists represent procedures with sequential steps.

♦ Bullet lists provide information, but do not involve sequential

steps.

→ Indicates selecting the option (on a menu or dialog box, for

example), that comes next. For example, Start → Run means

to open the Start menu, and then select Run.

Indicates critical information.

International http://www.aten.com

North America http://www.aten-usa.com

KH2508A / KH2516A User Manual

x

This Page Intentionally Left Blank

1

Chapter 1

Introduction

Overview

The KH2508A and KH2516A KVM switches are control units that allows IT

administrators to access and control multiple computers from two PS/2 or USB

KVM consoles (2 bus). Operators working at up to two consoles can

independently and simultaneously take control of up to 8 (KH2508A), or 16

(KH2516A) computers. By daisy chaining up to 15 additional switches, as

many as 256 computers can be controlled from the original KVM consoles.

These switches have been designed with unique and powerful features that

enable administrators to manage their entire server room and data center

devices easily and conveniently.

For example, the advanced Adapter ID feature stores the Adapter Cable's

configuration information - such as its ID, port name, OS, keyboard language,

etc. This feature allows administrators to relocate servers to different ports

without having to reconfigure the adapters . Other advances found with these

switches includes enhanced video quality - extending the distance to the

servers to up to 50 m* at a resolution of 1280 x 1024.

Compact, high-density, RJ-45 connectors and CAT 5e/6 cable make for a

compact, efficient, wiring configuration, while the use of PS/2 and USB KVM

Adapter Cables to link to the computers, permits any combination of PCs,

Macs, Sun computers, and serial devices to coexist on the installation.

Setting up the KH2508A / KH2516A is fast and easy – plugging cables into

their appropriate ports is all that is entailed. Because the KH2508A / KH2516A

intercepts keyboard and mouse input directly, there is no software to configure

and no complex installation routines.

Access to any computer on the installation is easily accomplished – either by

pressing front panel port selection pushbuttons; entering hotkey combinations

from the keyboard; or by means of a powerful OSD (On Screen Display) menu

system. A convenient Auto Scan function also permits automatic scanning and

one-by-one monitoring of the activities of selected computers.

Your KH2508A / KH2516A investment is protected through firmware

upgrades. You can download firmware update files from our website, and use

the Firmware Upgrade function to quickly and conveniently install them.

KH2508A / KH2516A User Manual

2

A KH2508A or KH2516A installation provides one of the best, and most

economical, solutions ATEN offers to the SMB market. There is no better way

to save time, space, and money than with a KH2508A or KH2516A KVM

switch.

Note: With KVM Adapter Cable KA7000 series. Please see KVM Adapter

Cables, page 5, for details.

Chapter 1. Introduction

3

Features

 Two KVM consoles independently and simultaneously control up to 8 or

16 directly connected computers

 Space-Saving RJ-45 connectors and Cat 5e/6 cabling

 By daisy chaining up to 15 additional KH2508A / KH2516A switches, as

many as 256 computers can be controlled from the original KVM consoles

 Console conversion – any type of KVM console can control any type of

computer; mixed combinations (PS/2&USB) supported on both the KVM

console and computer sides

 Superior Video Quality – Supports video resolutions up to 1920 x 1200 @

60 Hz up to 30 meters, 1600 x 1200 @ 60 Hz up to 40 meters, and 1280 x

1024 @ 75 Hz up to 50 meters*

 Configure port access rights for users on a port-by-port basis

 Diversified port operation mode enables flexible computer management –

Occupy, Exclusive and share modes

 Three port selection methods – Manual (via front panel pushbuttons),

Hotkey, and multi-language OSD (On Screen Display)

 Multiplatform support – PC, Mac, Sun, and serial

 Multiple User Accounts – Supports up to 10 user and 1 administrator

accounts

 Two-Level Password Security – Supports one administrator and ten user

profiles. Strong password Password protection prevents unauthorized

accessing to the installation

 Auto Scan mode enables continuous monitoring of user-selected

computers

 Broadcast Mode sends commands from the console to all computers –

allowing you to perform operations (such as software installation,

upgrades, shutdowns, etc.), on them simultaneously

 Adapter ID

 Firmware Upgradeable

Note: With the KVM adapter cable KA7000 series. Please see KVM Adapter

Cables, page 5, for details.

KH2508A / KH2516A User Manual

4

Requirements

Consoles

 A VGA, SVGA, or multisync monitor capable of the highest resolution

that you will be using on any computer in the installation

 A PS/2 or USB mouse

 A PS/2 or USB keyboard

Computers

The following equipment must be installed on the computers that connect to the

KH2508A or KH2516A KVM ports:

 A VGA, SVGA or multisync port

 A Type A USB port and USB host controller (for USB KVM adapter cable

connection, see following section)

- or -

6-pin Mini-DIN keyboard and mouse ports (for PS/2 KVM adapter cable

connection, see following section)

Chapter 1. Introduction

5

KVM Adapter Cables



Cat 5e/6 cable is required to connect the KH2508A / KH2516A to one of the

KVM adapter cables.



The following KVM adapter cables are required for use with the KH2508A /

KH2516A:

Note: 1. KVM adapter cables are referred to as I/O Modules in some dialog boxes.

2. The following cable models support the Adapter Cable ID function:

KA7166 / KA7168 / KA7169 / KA7920 / KA7970 / KA7520 / KA7570

/ KA7120 / KA7170 / KA7130

Operating Systems

Supported operating systems are shown in the table below:

1

Does not support USB.

2

Kernels below 2.6 do not support USB 2.0

Function Module

Connect to devices with PS/2 ports KA7920 / KA7520 / KA7120

KA9520 / KA9120

Connect to devices with USB ports KA7166 / KA7168 / KA7169

KA7970 / KA7570 / KA7170

KA9570 / KA9170

Connect to Sun Legacy systems (with 13W3 port) KA9130 / KA7130

Connect to Sun USB systems KA9170 / KA7170

Connect to serial based devices KA9140

OS Version

Windows

NT

1

, 2000, XP, 2003 Server, 2008 Server, Vista

Linux

2

RedHat 9.0, Fedora or later, RHEL AS 4, RHEL 5

SuSE 10 or later, OpenSUSE 10.2; SLES 10 SP1

Debian 3.1, 4.0

Ubuntu 7.04, 7.10

UNIX IBM AIX4.3, 5L (V5.2,V5.3), V6 (V6.1)

FreeBSD 5.5, 6.1, 6.2

Novell Netware 5.0 or later

Sun Solaris 8, 9, 10

Mac 9.0, 9.1, 10.1, 10.2, 10.3, 10.4 , 10.5

DOS

6.2 or later

1

KH2508A / KH2516A User Manual

6

Components

Front View

KH2508A

KH2516A

No. Component Description

1 Port Selection

Pushbuttons



Press a pushbutton to give the KVM focus to the computer

attached to its corresponding port.



Simultaneously pressing Pushbuttons 1 and 2 for 3 seconds

performs a keyboard and mouse reset.



Simultaneously pressing Pushbuttons 7 and 8 of the

KH2508

A

or Buttons 15 and 16 of the KH2516

A

starts Auto

Scan mode (see F7: SCAN, page 36, for auto scan details).

543 6

1&2

78

543 6

1&2

78

Chapter 1. Introduction

7

2 Port LEDs The Port LEDs are built into the Port Selection Pushbuttons.

The left ones are the On Line LEDs; the right ones are the

Selected Port LEDs:



An On Line LED lights GREEN to indicate that the computer

attached to its corresponding port is up and running. A

flashing LED indicates that the Port is being used for

cascading to another switch.



A Selected LED lights ORANGE to indicate that the computer

attached to its corresponding port is the one that has the

KVM focus. The LED is steady under normal conditions, but

flashes when its port is accessed under Auto Scan mode

(see F7: SCAN, page 36, for auto scan details).

3 Reset Switch Pressing this switch in performs a system reset.

Note: The switch is recessed and must be pushed with a small

object, such as the end of a paper clip, or a ballpoint pen.

4 Console

Selection

Pushbuttons

Press a pushbutton to select a console for manual port

selection. When you press one of the manual port selection

pushbuttons the selected console will be connected to that port.

The LED next to the pushbutton indicates which console is

selected.

5 Firmware

Upgrade

Recovery

Switch

During normal operation and while performing a firmware

upgrade, this switch should be in the NORMAL position. If a

firmware upgrade operation does not complete successfully,

this switch is used to perform a firmware upgrade recovery.

See Firmware Upgrade Recovery, page 57 for details.

6 Firmware

Upgrade Port

The Firmware Upgrade Cable that transfers the firmware

upgrade data from the administrator's computer to the

KH2508A / KH2516A (see page 51), plugs into this RJ-11

connector.

7 Power LED Lights to indicate that the KH2508A / KH2516A is powered and

ready to operate.

8 Station ID

LED

The KH2508A / KH2516A's Station ID is displayed here. If this

is a single station installation (see page 12), or the first station

on a daisy chained installation (see page 15), the KH2508A /

KH2516A has a station ID of 01.

On a daisy chained installation, the KH2508A / KH2516A auto-

senses its position and displays the station ID that corresponds

to its place in the chain. (see Port ID Numbering, page 21, for

details).

No. Component Description

KH2508A / KH2516A User Manual

8

Rear View

KH2508A

KH2516A

No. Component Description

1 Power Socket The power cord to the AC source plugs in here.

2 Power Switch This is a standard rocker switch that powers the KH2508A /

KH2516A on and off.

3 Daisy Chain

Ports

When daisy chaining units (see KVM Adapter Cable

Installation Diagrams cont., page 15), the daisy chain cables

plug in here. The port on the left is the Chain In port; the port

on the right is the Chain Out port.

4 Grounding

Terminal

The wire used to ground the unit connects here.

5 Console 1

Ports

The KH2508A / KH2516A supports two independent

consoles. If this is a single station installation, or if this is the

first station of a daisy chained installation, the keyboard,

monitor, and mouse that make up Local Console 1 plug into

section no. 5 and Local Console 2 plugs into section no. 6.

You can use any combination of PS/2 and USB keyboards

and mice for the console.

6 Console 2

Ports

7KVM Port

Section

The Cat 5e/6 cables that link to the KVM adapter cables

(which link to the computers) plug in here.

12

745 6

3

12

745 6

3

9

Chapter 2

Hardware Setup

Overview

For convenience and flexibility that allows mixing the PS/2, USB and serial

interfaces, the KH2508A / KH2516A’s design utilizes KVM adapter cables

that serve as intermediaries between the KVM switch and the connected

devices:

A separate KVM adapter cable is required for each computer or device

connection. The KVM adapter cables are listed in the KVM Adapter Cables

section on page 5. Consult your dealer to find out which KVM adapter cables

best fit your needs.

Before you Begin

1. Important safety information regard

ing the placement of this

device is provided on page 61. Please review it before proceeding.

2.

Make sure that the power to any device that you connect to the

installation has been turned off. You m

ust unplug the power cords

of any computers that have the Keyboard Power On function.

KH2508A / KH2516A User Manual

10

Stacking and Rack Mounting

The KH2508A / KH2516A can be stacked on the desktop or rack mounted at

the front or rear of the rack. The following sections take you through the

procedures for each method.

Note: 1. Allow at least 5.1 cm on each side for adequate ventilation and

12.7 cm at the rear for power cord and cable clearance.

2. The standard rack mount kit does not include rack mount screws or

cage nuts. If you need additional rack mount screws or cage nuts,

contact your rack dealer.

Stacking

The KH2508A / KH2516A can be placed on any appropriate level surface that

can safely support its weight plus the weight of its attached cables. To place the

KH2508A / KH2516A, or to stack units if you are daisy chaining them, remove

the backing material from the bottom of the rubber feet that came with this

package, and stick them onto the switch’s bottom panel at the corners, as

shown in the diagram, below:

La page charge ...

ATEN KH2516A Manuel utilisateur

Ce manuel convient également à

ATEN KH2516A Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents