Cisco Systems Network Hardware 15454 Manuel utilisateur

Cisco Systems
Marque
Cisco Systems
Modèle
Network Hardware 15454
Taper
Manuel utilisateur

Ce manuel convient également à

xxxv
Cisco ONS 15454 SDH Reference Manual, R8.0
August 2012
About this Manual
Note The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms
do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring configuration.
Rather, these terms, as well as "Path Protected Mesh Network" and "PPMN," refer generally to Cisco's
path protection feature, which may be used in any topological network configuration. Cisco does not
recommend using its path protection feature in any particular topological network configuration.
This section explains the objectives, intended audience, and organization of this publication and
describes the conventions that convey instructions and other information.
This section provides the following information:
• Revision History
• Document Objectives
• Audience
• Related Documentation
• Document Conventions
• Obtaining Optical Networking Information
• Obtaining Documentation and Submitting a Service Request
Revision History
Date Notes
March 2007 Added the Revision History table.
April 2007
• Changed fuse rating and power consumption specifications in Appendix A.
• Added note to indicate the support for LO circuits in SNCP in XC-VXC-10G
card in the “Common Control Cards” chapter.
May 2007 Added OC48 IR/STM16 SH AS 1310 card information in the “Optical Cards”
chapter and Appendix A.
August 2007 Updated the note in the SNCP Circuits section of the Circuits and Tunnels chapter.
xxxvi
Cisco ONS 15454 SDH Reference Manual, R8.0
August 2012
October 2007 • Added a table with Border Error Rates and a corresponding Note in the
Performance Monitoring chapter.
• Updated Table Footnote 4 under Section STM-1 Card Performance
Monitoring Parameters in Chapter 15- Performance Monitoring.
• Added the Section 1.10.3 Pilot Fuse.
• Added the Sub-section 11.20.1 VCAT Circuit Routing over Server Trails.
• Updated About this Manual chapter.
January 2008 Updated cabling details for ONS-SE-ZE-EL SFP
March 2008 Removed SFP ONS-SI-622-I1-MM= and added SFPs ONS-SI-155-SR-MM= and
ONS-SI-622-SR-MM= in the following:
• Optical Cards chapter
• Hardware Specifications apendix
April 2008
• Corrected the Transmitter Output Power Min/Max for ONS-SI-155-SR-MM=
and ONS-SI-622-SR-MM=.
• Added a Note in the “User Password, Login, and Access Policies” section of
the Security chapter.
• Added a Caution in the “Single and Dual Rolls” section of the Circuits and
Tunnels chapter.
• Updated note on protection switching in “Link Capacity Adjustment” section
of Chapter 11, Circuits and Tunnels.
May 2008 Added power-level LED information for TCC2 and TCC2P cards in Chapter 2,
Common Control Cards.
July 2008
• Updated the section “15454_MRC-12 Port-Level Indicators” in the Optical
Cards chapter, to show the correct number and status of the Rx indicator.
• Updated the section “MRC-2.5G-12Port-Level Indicators” in the Optical
Cards chapter, to show the correct number and status of the Rx indicator.
• Added a note in section 10.1 “Timing Parameters” of Chapter 10, Timing.
August 2008 Updated the RPR details for the ML-MR-10 card in section 5.8 ML-MR-10 Card
of Chapter 5, Ethernet Cards.
September 2008
• Added a note in Card Default Settings and Node Default Settings section of
Appendix C, Network Element Defaults.
• Added a Warning for all optical cards in Chapter 4, Optical Cards.
• Updated the maximum current rating and fusing in section “A.1.9 System
Power” of Appendix A, Hardware Specifications.
• Updated FC_MR-4 Statistics Parameters table in the chapter, Performance
Monitoring.
• Updated “Table 4-17 Line Rate Configurations Per 15454_MRC-12 Port,
Based on Available Bandwidth” in Chapter 4, Optical Cards.
• Updated the Software and Hardware Compatibility section.
• Updated “Table 11-4 DCC Tunnel” in Chapte 11, Circuits and Tunnels.
Date Notes
xxxvii
Cisco ONS 15454 SDH Reference Manual, R8.0
August 2012
October 2008 Updated the section “4.15.2 Ports and Line Rates” and “Table 4-17 Line Rate
Configurations Per 15454_MRC-12 Port, Based on Available Bandwidth” in
Chapter 4, Optical Cards.
November 2008
• Updated the list of PM parameters for MRC-12 and MRC-4 cards in Chapter
16, Performance Monitoring.
• Updated Server Trail section in Chapter 11, Circuits and Tunnels.
• Updated the section “Compatibility by Card” in the chapter, “Optical Cards”.
January 2009 Updated the SFP and XFP Card Compatibility table in Chapter 4, Optical Cards.
March 2009
• Added a note in section “5.11 CE-MR-10 Card” of Chapter 5, Ethernet Cards.
• Updated the SFP and XFP Specifications table in Appendix A.
April 2009
• Updated Figure 7-1 in Chapter 7, Card Protection.
• Updated the "TCC2P Card Specifications" section in Appendix A.
• Updated the Cisco ONS 15454 SDH bandwidth specifications section in
“A.1.1 Bandwidth” of Appendix A, Hardware Specifications.
• Updated Table 11-13 and Table 11-14 in Chapter 11, Circuits and Tunnels.
May 2009
• Updated the section “User Password, Login, and Access Policies” in Chapter
9, Security.
June 2009
• Updated “STM-N Speed Upgrades” in Chapter 12, SDH Topologies and
Upgrades.
July 2009
• Updated the table “PM Parameters for the STM-1 and STM1 SH 1310-8
Cards” in Chapter 15, Performance Monitoring.
• Updated the section “CE-1000-4 Card” in Chapter 5, Ethernet Cards.
• Added a new section, Comparison of the Protection Schemes in the chapter,
SDH Topologies and Upgrades.
November 2009
• Updated the table “Line Rate Configurations Per 15454_MRC-12 Port, Based
on Available Bandwidth” in the chapter, “Optical Cards”.
January 2010 Updated the section “STM-N Speed Upgrades” in the chapter SDH Topologies
and Upgrades.
February 2010
• Changed the BIEC parameter to BIT-EC in Chapter 15, “Performance
Monitoring”.
• Updated the SFP/XFP Card Compatibility table for ADM-10G card in
chapter Transponder and Muxponder Cards.
April 2010
• Updated the section “SNMP Overview” in the chaper “SNMP”.
August 2010
• Updated the section “Bridge and Roll” in the chapter “Circuits and Tunnels”.
• Removed the reference to G1000 card support in the chapters “Shelf and
FMEC Hardware”, “Network Element Defaults”, “Performance Monitoring”,
and “Ethernet Cards”.
November 2010 Updated the figure “ML1000-2 Faceplate and Block Diagram” under the section
“ML1000-2 Card” in the chapter “Ethernet Cards”.
Date Notes
xxxviii
Cisco ONS 15454 SDH Reference Manual, R8.0
August 2012
Document Objectives
This manual provides reference information for the Cisco ONS 15454 SDH.
Audience
To use this publication, you should be familiar with Cisco or equivalent optical transmission hardware
and cabling, telecommunications hardware and cabling, electronic circuitry and wiring practices, and
preferably have experience as a telecommunications technician.
Related Documentation
Use the Cisco ONS 15454 SDH Reference Manual with the following referenced publications:
• Cisco ONS 15454 SDH Procedure Guide, Release 8.0
Provides procedures to install, turn up, provision, and maintain a Cisco ONS 15454 SDH node and
network.
• Cisco ONS 15454 SDH Troubleshooting Guide, Release 8.0
Provides general troubleshooting procedures, alarm description and troubleshooting procedures,
error messages, and transient conditions.
• Cisco ONS 15454 SDH and Cisco ONS 15600 SDH TL1 Command Guide, Release 8.0
Provides a full TL1 command and autonomous message set including parameters, AIDs, conditions
and modifiers for the Cisco ONS 15454 SDH and Cisco ONS 15600 SDH.
• Cisco ONS 15454 SDH and Cisco ONS 15600 SDH TL1 Reference Guide, Release 8.0
Provides general information, procedures, and errors for TL1 in the Cisco ONS 15454 SDH and
Cisco ONS 15600 SDH.
• Cisco ONS 15454 and Cisco ONS 15454 SDH Ethernet Card Software Feature and Configuration
G uide, Release 8.0
Provides software features for all Ethernet cards and configuration information for Cisco IOS on
Ethernet cards.
• Release Notes for the Cisco ONS 15454 SDH Release 8.0
Provides caveats, closed issues, and new feature and functionality information.
May 2011
• Updated the sections “Link Capacity Adjustment” and “VCAT Circuit Size”
in the chapter “Circuits and Tunnels”.
• Updated the tables “ONS 15454 Card VCAT Circuit Rates and Members” and
“ONS 15454 VCAT Card Capabilities” in the chapter “Circuits and Tunnels”.
June 2011 Updated the section “AIC-I Card” in the chapter “Common Control Cards”.
January 2012 Updated the privileges for the Download/Cancel operations in the table, "ONS
15454 SDH Security Levels—Network View " in the chapter, “Security”.
February 2012 Updated the table “SFP and XFP Card Compatibility” in the chapter “Optical
Cards”.
August 2012 The full length book-PDF was generated.
Date Notes
xxxix
Cisco ONS 15454 SDH Reference Manual, R8.0
August 2012
For an update on End-of-Life and End-of-Sale notices, refer to
http://www.cisco.com/en/US/products/hw/optical/ps2006/prod_eol_notices_list.html.
Document Conventions
This publication uses the following conventions:
Note Means reader take note. Notes contain helpful suggestions or references to material not covered in the
document.
Caution Means reader be careful. In this situation, the user might do something that could result in equipment
damage or loss of data.
Convention Application
boldface Commands and keywords in body text.
italic Command input that is supplied by the user.
[ ] Keywords or arguments that appear within square brackets are optional.
{ x | x | x } A choice of keywords (represented by x) appears in braces separated by
vertical bars. The user must select one.
Ctrl The control key. For example, where Ctrl + D is written, hold down the
Control key while pressing the D key.
screen font Examples of information displayed on the screen.
boldface screen font Examples of information that the user must enter.
< > Command parameters that must be replaced by module-specific codes.
xl
Cisco ONS 15454 SDH Reference Manual, R8.0
August 2012
Warning
IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar
with standard practices for preventing accidents. Use the statement number provided at the end of
each warning to locate its translation in the translated safety warnings that accompanied this
device.
Statement 1071
SAVE THESE INSTRUCTIONS
Waarschuwing
BELANGRIJKE VEILIGHEIDSINSTRUCTIES
Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan
veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij
elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard
praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de
waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt
raadplegen.
BEWAAR DEZE INSTRUCTIES
Varoitus
TÄRKEITÄ TURVALLISUUSOHJEITA
Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin
käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu
onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen
mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien
lausuntonumeroiden avulla.
SÄILYTÄ NÄMÄ OHJEET
Attention
IMPORTANTES INFORMATIONS DE SÉCURITÉ
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant
entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez
conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures
couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des
avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil,
référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.
CONSERVEZ CES INFORMATIONS
Warnung
WICHTIGE SICHERHEITSHINWEISE
Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen
kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und
den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder
Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten
Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.
BEWAHREN SIE DIESE HINWEISE GUT AUF.
xli
Cisco ONS 15454 SDH Reference Manual, R8.0
August 2012
Avvertenza
IMPORTANTI ISTRUZIONI SULLA SICUREZZA
Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle
persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli
relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti.
Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le
traduzioni delle avvertenze riportate in questo documento.
CONSERVARE QUESTE ISTRUZIONI
Advarsel
VIKTIGE SIKKERHETSINSTRUKSJONER
Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du
begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med
elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten
av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne
enheten.
TA VARE PÅ DISSE INSTRUKSJONENE
Aviso
INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de
lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos
perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de
prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para
localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.
GUARDE ESTAS INSTRUÇÕES
¡Advertencia!
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular
cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los
procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el
número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña
a este dispositivo.
GUARDE ESTAS INSTRUCCIONES
Varning!
VIKTIGA SÄKERHETSANVISNINGAR
Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada.
Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och
känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av
varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna
anordning.
SPARA DESSA ANVISNINGAR
xlii
Cisco ONS 15454 SDH Reference Manual, R8.0
August 2012
xliii
Cisco ONS 15454 SDH Reference Manual, R8.0
August 2012
Aviso
INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões
corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os
circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o
número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de
segurança traduzidos que acompanham o dispositivo.
GUARDE ESTAS INSTRUÇÕES
Advarsel
VIGTIGE SIKKERHEDSANVISNINGER
Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for
legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de
involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til
undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de
oversatte advarsler, der fulgte med denne enhed.
GEM DISSE ANVISNINGER
xliv
Cisco ONS 15454 SDH Reference Manual, R8.0
August 2012
xlv
Cisco ONS 15454 SDH Reference Manual, R8.0
August 2012
Obtaining Optical Networking Information
This section contains information that is specific to optical networking products. For information that
pertains to all of Cisco, refer to the Obtaining Documentation and Submitting a Service Request section.
Where to Find Safety and Warning Information
For safety and warning information, refer to the Cisco Optical Transport Products Safety and
Compliance Information document that accompanied the product. This publication describes the
international agency compliance and safety information for the Cisco ONS 15454 system. It also
includes translations of the safety warnings that appear in the ONS 15454 system documentation.
Cisco Optical Networking Product Documentation CD-ROM
Optical networking-related documentation, including Cisco ONS 15xxx product documentation, is
available in a CD-ROM package that ships with your product. The Optical Networking Product
Documentation CD-ROM is updated periodically and may be more current than printed documentation.
Obtaining Documentation and Submitting a Service Request
For information on obtaining documentation, submitting a service request, and gathering additional
information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and
revised Cisco technical documentation, at:
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html
Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS)
feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds
are a free service and Cisco currently supports RSS version 2.0.
xlvi
Cisco ONS 15454 SDH Reference Manual, R8.0
August 2012
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Cisco Systems Network Hardware 15454 Manuel utilisateur

Cisco Systems
Marque
Cisco Systems
Modèle
Network Hardware 15454
Taper
Manuel utilisateur
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents