Transition Networks TN-CWDM-SFP-1290 Manuel utilisateur

Marque: Transition Networks

Modèle: TN-CWDM-SFP-1290

Catégorie: Convertisseurs de média réseau

Taper: Manuel utilisateur

*Unless otherwise indicated, the distances listed are the typical maximum cable

distance. The actual maximum cable distances are dependent upon the physical

characteristics of the network installation.

**Transition Networks' SFP modules fully comply with the Multi-Sourcing Agreement

(MSA). This compliance allows our SFP modules to be used in other MSA compliant

SFP platforms without problems. In

addition, TN SFP modules specified in

this manual are also compatible with all

Cisco SFP-based routers and switches, as

well as its IOS software. TN SFP

modules ARE NOT

Cisco OEM brand

modules.

User’s Guide

TN-GLC-xx-xx and TN-CWDM-SFP-1xx0 Cisco

CompatibleSmall Form Factor Pluggable (SFP)

Transceiver Modules**

The Transition Networks TN-GLC-xx-xx and TN-CWDM-

SFP-1xx0 series small form factor pluggable (SFP) transceiver

modules are designed to install in any SFP port, allowing for1000Base-T, 1000Base-SX

or 1000Base-LX interfaces to the network through the SFP connector. The TN-GLC-xxx

and TN-CWDM-SFP-1xx0 transceivers are designed for bi-directional serial-optical data

communications such as Gigabit Ethernet or fiber channel at speeds up to 2.125 Gbps.

Installation . . . . . . . . . . . . . . . . . . . . . . . . .3

Cable Specifications . . . . . . . . . . . . . . . . .5

Technical Specifications . . . . . . . . . . . . . .8

Compliance Information . . . . . . . . . . . . .11

Part Number Port Description

TN-GLC-T

1000Base-T , RJ-45

100m (328 ft)*

TN-GLC-SX-MM

1000Base-SX, duplex LC, 850 nm,

220 m (722 ft)* on 62.5/125 µm fiber

550 m (1840 ft)* on 50/125 µm fiber

TN-GLC-SX-MM-2K

1000Base-SX, duplex LC 1300 nm, extended multimode

up to 2 km (1.2 miles)*

TN-GLC-LH-SM

1000Base-LX, 1310 nm, single mode

10 km (6.2 miles)*

TN-GLC-BX-U

1000Base-BX, Simplex LC 1310 nm Tx/1490 nm Rx nm,

single mode, single fiber 10 km (6.2 miles)*

TN-GLC-BX-D

1000Base-BX, Simplex LC 1490 nm Tx/1310 nm Rx nm,

single mode, single fiber 10 km (6.2 miles)*

TN-GLC-SX-MM

TN-CWDM-SFP-1xx0

TN-GLC-BX-0

TN-GLC-T

TN-GLC-xx-xx SFPs

Tech Support: 1-800-260-1312 -- International: 00-1-952-941-7600—24 hours

Part Number Port Description

TN-GLC-BX-U

1000Base-BX, Simplex LC 1310 nm Tx/1490 nm Rx,

single mode, single fiber 10 km (6.2 miles)*

TN-GLC-BX-D

1000Base-BX, Simplex LC 1490 nm Tx/1310 nm Rx,

single mode, single fiber 10 km (6.2 miles)*

TN-GLC-BX-U-40

1000Base-BX, Simplex LC 1310 nm Tx/1490 nm Rx,

single mode, single fiber 40 km (24.9 miles)*

TN-GLC-BX-D-40

1000Base-BX, Simplex LC 1490 nm Tx/1310 nm Rx,

single mode, single fiber 40 km (24.9 miles)*

TN-GLC-BX-U-60

1000Base-BX, Simplex LC 1310 nm Tx/1490 nm Rx,

single mode, single fiber 60 km (37.3 miles)*

TN-GLC-BX-D-60

1000Base-BX, Simplex LC 1490 nm Tx/1310 nm Rx,

single mode, single fiber 60 km (37.3 miles)*

TN-GLC-FE-100BX-U

100Base-BX, Simplex LC 1310 nm Tx/1550 nm Rx,

single mode, single fiber 20 km (12.4 miles)*

TN-GLC-FE-100BX-D

100Base-BX, Simplex LC 1550 nm Tx/1310 nm Rx ,

single mode, single fiber 20 km (12.4 miles)*

TN-GLC-FE-100FX

100Base-BX, Duplex LC 1300 nm, multimode

2 km (1.2 miles)*

TN-GLC-FE-100LX

100Base-BX, Duplex LC 1310 nm, single mode

20 km (12.4 miles)*

TN-GLC-GE-100FX***

100Base-BX, Duplex LC 1300 nm, multimode

2 km (1.2 miles)*

TN-GLC-ZX-SM

1000Base-LX, 1550 nm, single mode

80 km (49.7 miles)*

TN-CWDM-SFP-1xx0

1000Base-LX, single mode

80 km (49.7 miles)*

27 =1270nm 39 = 1390nm 53 = 1530nm

29 = 1290nm 41 = 1410nm 55 = 1550nm

31 = 1310nm 43 = 1430nm 57 = 1570nm

33 = 1330nm 47 = 1470nm 59 = 1590nm

35 = 1350nm 49 = 1490nm 61 = 1610nm

37 = 1370nm 51 = 1510nm

xx = center wavelength (λ

) (See technical specifications for more details.)

*Unless otherwise indicated, the distances listed are the typical maximum cable

distance. The actual maximum cable distances are dependent upon the physical

characteristics of the network installation.

**Transition Networks' SFP modules fully comply with the Multi-Sourcing

Agreement (MSA). This compliance allows our SFP modules to be used in other

MSA compliant SFP platforms without problems. In addition, TN SFP modules

are also compatible with all Cisco SFP-based routers and switches, as well as its

IOS software. TN SFP modules ARE NOT

Cisco OEM brand modules.

[email protected] -- Click the “Transition Now” link for a live Web chat.

Installation

Installing the SFP transceiver

To install the SFP module into a network switches media converter, do the

following:

1. Position the module at the installation slot so that the label faces up.

2. Carefully slide the module into the installation slot, aligning it with the internal

installation guides.

Installing copper cables

1. Locate or build 1000Base-T compliant copper cables with male, RJ-45

connectors installed at both ends.

2. Connect the RJ-45 connector at one end of the cable to the RJ-45 port on the

media converter.

3. Connect the RJ-45 connector at the other end of the cable to the RJ-45 port on

the other device.

RJ-45 port

on the other device

(switch, work station, etc

RJ-45 port

on the media

converter

***Provide 100Base-FX interface when plugged into a gigabit SFP slot on Cisco

catalyst 3750, 3560, and 2970 series switches.

Note: Install simplex or single fiber SFP models in pairs in the same network where

one is the local SFP and the other is the remote SFP.

TN-GLC-xx-xx SFPs

Tech Support: 1-800-260-1312 -- International: 00-1-952-941-7600 -- (24 hours)

Connect fiber cable

to media converter

as shown.

Connect fiber cable

to other device

(media converter,

hub, etc.) as shown

Installing the fiber cables

1. Locate or build 1000Base-SX-compliant or 1000Base-LX-compliant fiber

cable with male TX to RX connectors installed at both ends.

2. Install the fiber cable as shown below.

[email protected] -- Click the “Transition Now” link for a live Web chat.

Cable Specification

Copper cable (Category 5 -- minimum requirement)

• Gauge = 24 to 22 AWG; Attenuation = 22.0 dB /100m @ 100 MHz

• Straight-through OR crossover cable may be used.

• Shielded twisted-pair (STP) OR unshielded twisted-pair (UTP) may be used

• All pin pairs (1&2, 3&6, 4&5, 7&8) are active in a gigabit network.

• Use only dedicated wire pairs for the active pins; e.g., blue/white &

white/blue,

orange/white & white/orange, etc.

• Do not use flat or silver satin wire.

Crossover Cable

Straight-Through Cable

wisted Pair #1

Twisted Pair #1

Twisted Pair #2

wisted Pair #2

TN-GLC-xx-xx SFPs

Tech Support: 1-800-260-1312 -- International: 00-1-952-941-7600 -- (24 hours)

Fiber cable

The physical characteristics must meet or exceed IEEE 802.3z™ specifications.

Singlemode fiber (recommended): 9 µm

Multimode fiber (recommended): 62.5/125 µm

Multimode fiber (optional): 100/140, 85/140, 50/125 µm

TN-GLC-SX-MM 850 nm multimode

Fiber Optic Transmitter Power: min: -9.5 dBm max: -3.5 dBm

Fiber Optic Receiver Sensitivity: min: -18.0 dBm max: -1.0 dBm

Link Budget: 8.5 dB

TN-GLC-SX-MM-2k 1300 nm multimode

Fiber Optic Transmitter Power: min: -9.0 dBm max: -1.0dBm

Fiber Optic Receiver Sensitivity: min: -19.0 dBm max: -1.0 dBm

Link Budget: 18.0 dB

TN-GLC-LH-SM 1310 nm singlemode

Fiber Optic Transmitter Power: min: -9.5 dBm max: -3.0 dBm

Fiber Optic Receiver Sensitivity: min: -20.0 dBm max: -3.0 dBm

Link Budget: 10.5 dB

TN-GLC-BX-U 1310 nm Tx/1490 nm Rx single mode

TN-GLC-BX-D 1490 nm Tx/1310 nm Rx single mode

Fiber Optic Transmitter Power: min: -9.0 dBm max: -1.0 dBm

Fiber Optic Receiver Sensitivity: min: -21.0 dBm max: -1.0 dBm

Link Budget: 12.0 dB

TN-GLC-BX-U-40 1310 nm Tx/1490 nm Rx single mode

TN-GLC-BX-D-40 1490 nm Tx/1310 nm Rx single mode

Fiber Optic Transmitter Power: min: -3.0 dBm max: +2.0 dBm

Fiber Optic Receiver Sensitivity: min: -23.0 dBm max: -1.0 dBm

Link Budget: 20.0 dB

TN-GLC-BX-U-60 1310 nm Tx/1490 nm Rx single mode

TN-GLC-BX-D-60 1490 nm Tx/1310 nm Rx single mode

Fiber Optic Transmitter Power: min: -2.0 dBm max: +4.0 dBm

Fiber Optic Receiver Sensitivity: min: -25.0 dBm max: -1.0 dBm

Link Budget: 23.0 dB

TN-GLC-FE-100BX-U 1310 nm Tx/1550 nm Rx single mode

TN-GLC-FE-100BX-D 1550 nm Tx/1310 nm Rx single mode

Fiber Optic Transmitter Power: min: -14.0 dBm max: -8.0 dBm

Fiber Optic Receiver Sensitivity: min: -32.0 dBm max: -0.0 dBm

Link Budget: 18.0 dB

Fiber cable -- continued

TN-GLC-FE-100FX 1300 nm multimode

TN-GLC-GE-100FX 1300 nm multimode

Fiber Optic Transmitter Power: min: -23.5 dBm max: -14.0 dBm

Fiber Optic Receiver Sensitivity: min: -32.0 dBm max: -8.0 dBm

Link Budget: 8.5 dB

TN-GLC-FE-100LX 1310 nm single mode

Fiber Optic Transmitter Power: min: -15.0 dBm max: -8.0 dBm

Fiber Optic Receiver Sensitivity: min: -34.0 dBm max: -0.0 dBm

Link Budget: 19.0 dB

TN-GLC-ZX-SM 1550 nm single mode

Fiber Optic Transmitter Power: min: 0.0 dBm max: +5.0 dBm

Fiber Optic Receiver Sensitivity: min: -24.0 dBm max: -3.0 dBm

Link Budget: 24 dB

TN-CWDM-SFP-1xx0 1270nm -1610nm single mode

Fiber Optic Transmitter Power: min: 0.0 dBm max: +5.0 dBm

Fiber Optic Receiver Sensitivity: min: -25.0 dBm max: -3.0 dBm

Link Budget: 25 dB

For the most up-to-date information on the TN-GLC-xx-xx transceiver module, view

the user’s guide on-line at: www.transition.com.

Product is certified by the manufacturer to comply with DHHS Rule 21/CFR,

Subchapter J applicable at the date of manufacture.

WARNING:

Visible and invisible laser radiation when open. Do not stare into beam

or view directly with optical instruments. Failure to observe this warning could result

damage to your eyes or blindness.

WARNING:

Use of controls, adjustments or the performance of procedures other than

those specified herein could result in hazardous radiation exposure.

The fiber optic transmitters on this device meet Class I Laser safety requirements per

IEC-825/CDRH standards and comply with 21 CFR1040.10 and 21CFR1040.11.

[email protected] -- Click the “Transition Now” link for a live Web chat.

TN-GLC-xx-xx SFPs

Tech Support: 1-800-260-1312 -- International: 00-1-952-941-7600 -- (24 hours)

Technical Specification

For use with Transition Networks Model TN-GLC-xxx or equivalent.

Standard: IEEE 802.3 2003; ANSI X3.297-1997

TN-GLC-FE-xxx

and TN-GLC-GE-xxx: Compiant with

IEEE 802.3 100Base-Fx; IEEE802.3ah 100Base-Bx;

Intermediate - Reach Sonet OC-3/SDH STM-1 (s-1-1)

TN-GLC-xx-xx and TN-CWDM-SFP-1xx0 modules:

Compliant with IEEE 802.3z Gigabit Ethernet; FC-1x/2x SM-LC-L FC-PI.

TN-GLC-T modules: Compliant with IEEE 802.32 Gigabit

Ethernet (1000Base-T)

Output wavelength -6.0 <

λc < +7.5 nm

Dimensions: 0.52 x 2.18 x 0.33’’ (13.4 x 55.5 x 8.5 mm, Fiber)

0.95 x 2.8 x 0.54” (14-0 x 71.1 13.7 mm, Copper)

Weight: 1 oz. (28 g) approximately

Power: 3.3V, Fiber 0.66 W; Copper 1.0 W

Operating Temp: 0°C to 70°C (32°F to 158° F )

Storage Temp: -40°C to 85°C (-40° to 185°F)

Humidity: 5% to 95%, non-condensing

Altitude: 0 to 10,000 feet

Warranty: Lifetime

Note: Transition Networks' SFP modules fully comply with the Multi-Sourcing

Agreement (MSA). This compliance allows our SFP modules to be used in

other MSA compliant SFP platforms without problems. In addition, TN SFP

modules are also compatible with all Cisco SFP-based routers and switches, as

well as its IOS software and SMARTnet. TN SFP modules ARE NOT

Cisco

OEM brand modules.

[email protected] -- Click the “Transition Now” link for a live Web chat.

Technical support

Technical support is available 24 hours a day.

U.S.A. and Canada: 1-800-260-1312

International: 00-1-952-941-7600

Transition now

Chat live via the Web with Transition Networks Technical Support.

Log onto www.transition.com and click the Transition Now link.

Web-Based seminars

Transition Networks provides seminars via live web-based training.

Log onto www.transition.com and click the Learning Center link.

E-Mail

Ask a question anytime by sending an e-mail to our technical support staff.

[email protected]

Address

Transition Networks

10900 Red Circle Drive

Minnetonka, MN 55343, U.S.A.

telephone: 952-941-7600

toll free: 800-526-9267

fax: 952-941-2322

TN-GLC-xx-xx SFPs

Tech Support: 1-800-260-1312 -- International: 00-1-952-941-7600 -- (24 hours)

Declaration of Conformity

Name of Mfg: Transition Networks

10900 Red Circle Drive, Minnetonka MN 55343 U.S.A.

Model: TN-GLC-xx-xx Series Transceiver Modules

Part Number(s): TN-GLC-T, TN-GLC-SX-MM, N-GLC-SX-MM-2k,

TN-GLC-LH-SM, TN-GLC-BX-U, TN-GLC-BX-D,

TN-GLC-BX-U-40, TN-GLC-BX-D-40, TN-GLC-BX-U-60,

TN-GLC-BX-D-60, TN-GLC-FE-100BX-U,

TN-GLC-FE-100BX-D, TN-GLC-FE-100FX,

TN-GLC-FE-100LX, TN-GLC-GE-100LX, TN-GLC-ZX-SM,

TN-CWDM-SFP-1xx0

Regulation: EMC Directive 89/336/EEC

Purpose: To declare that the TN-GLC-xxx to which this declaration refers

is in conformity with the following standards:

IEC 60825-1; IEC60825-2; FC1X/2X SM-LC-L FC-PI; IEEE 802.3z 2003; ANSI X3.297

1997; Class A; FDA 21; CFR1040.10; CFR1040.11

I, the undersigned, hereby declare that the equipment specified above conforms to the above

Directive(s) and Standard(s).

October 2008____

Stephen Anderson, Vice-President of Engineering Date

[email protected] -- Click the Transition Now link for a live Web chat.

Compliance Information

CE Mark: IEC-60825; FDA 21; CFR 1040.10 and 1040.11

FCC regulations

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference, in which

case the user will be required to correct the interference at the user's own expense.

Canadian regulations

This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out

on the radio interference regulations of the Canadian Department of Communications.

Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites

applicables aux appareils numériques de la Class A prescrites dans le Règlement sur le brouillage

radioélectrique édicté par le ministère des Communications du Canada.

European regulations

Warning

This is a Class A product. In a domestic environment this product may cause radio interference in

which case the user may be required to take adequate measures.

Achtung !

Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können bei Betrieb dieses

Gerätes Rundfunkstörungen auftreten. In diesem Fäll ist der Benutzer für Gegenmaßnahmen

verantwortlich.

Attention !

Ceci est un produit de Classe A. Dans un environment domestique, ce produit risque de créer des

interférences radioélectriques, il appartiendra alors à l'utilsateur de prende les measures spécifiques

appropriées.

In accordance with European Union Directive 2002/96/EC of the European Parliament

and of the Council of 27 January 2003, Transition Networks will accept post usage

returns of this product for proper disposal. The contact information for this activity can

be found in the 'Contact Us' portion of this document.

CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO THE

PUBLIC TELEPHONE NETWORK. Failure to observe this caution could result in

damage to the public telephone network.

Der Anschluss dieses Gerätes an ein öffentlickes Telekommunikationsnetz in den EG-

Mitgliedstaaten verstösst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der

Richtlinie 91/263/EWG zur Angleichung der Rechtsvorschriften der Mitgliedstaaten über

Telekommunikationsendeinrichtungen einschliesslich der gegenseitigen Anerkennung ihrer

Konformität.

Trademark notice

All trademarks and registered trademarks are the property of their respective owners.

be reproduced or used in any form or means (graphic, electronic, mechanical) without written

permission from Transition Networks.

33389.D

Printed in the U.S.A.

TN-GLC-xx-xx SFPs

Transition Networks TN-CWDM-SFP-1290 Manuel utilisateur

Marque: Transition Networks

Modèle: TN-CWDM-SFP-1290

Catégorie: Convertisseurs de média réseau

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Transition Networks TN-CWDM-SFP-1290 User manual

Transition Networks TN-CWDM-SFP-1290 Manuel utilisateur

Transition Networks TN-CWDM-SFP-1290 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents