Transition Networks Switch CERTXFX01(SM) Manuel utilisateur

Marque: Transition Networks

Modèle: Switch CERTXFX01(SM)

Taper: Manuel utilisateur

Ce manuel convient également à

COMPLIANCE INFORMATION

UL Listed

C-UL Listed (Canada)

CISPR/EN55022 Class A

FCC Regulations

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant

to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference, in which case the user will be

required to correct the interference at the user’s own expense.

Canadian Regulations

This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on

the radio interference regulations of the Canadian Department of Communications.

Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables

aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique

édicté par le ministère des Communications du Canada.

European Regulations

Warning

This is a Class A product. In a domestic environment this product may cause radio interference in which

case the user may be required to take adequate measures.

Achtung !

Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können bei Betrieb dieses Gerätes

Rundfunkstörungen auftreten, in weichen Fällen der Benutzer für entsprechende Gegenmaßnahmen

werantwortlich ist.

Attention !

Ceci est un produit de Classe A. Dans un environment domestique, ce produit risque de créer des

interférences radioélectriques, il appartiendra alors à l’utilsateur de prende les measures spécifiques

appropriées

Trademark Notice

All registered trademarks and trademarks are the property of their respective owners.

graphic, electronic, or mechanical – without written permission from TRANSITION Networks.

Printed in the U.S.A. 33113.A

Designed to be installed in the TRANSITION Networks E-MCC-1600 Media

Converter Chassis, C/E-R-TX-FX-01 series redundant Fast Ethernet

™ media converters

connect 100BASE-TX unshielded twisted pair copper to 1300 nm 100BASE-FX

multimode OR to 1300 nm 100BASE-FX singlemode fiber. In the event of a failure

in the primary copper or fiber connection, a fully redundant secondary connection

is made available to the failed copper or fiber connection. Also, the copper and

fiber media converter interfaces operate independently, so that a failure on one

interface will not force a failure on the other interface.

Switches at the side of the media converter allow selection of auto-negotiation and

of full/half-duplex. Also, a port select timer (PST) switch* allows the network

administrator to set different timer values (used when a primary connection is lost

and a secondary connection is made) at each end of the copper/fiber interface.

(*See note on page 5.)

Minneapolis, MN 55344 USA

Redundant Fast Ethernet

™

100BASE-TX/100BASE-FX 1300 Nanometer

Slide-In-Module Media Converters

C/E-R-TX-FX-01, C/E-R-TX-FX-01(SC), C/E-R-TX-FX-01(SM)

USER’S GUIDE

C/E-R-TX-FX-01

Provides two (2) RJ-45 twisted pair

100BASE-TX connectors and two (2)

sets of RX (receive) and TX (transmit)

ST 100BASE-FX connectors to 1300

nm multimode fiber-optic cable.

C/E-R-TX-FX-01(SC)

Provides two (2) RJ-45 twisted pair

100BASE-TX connectors and two (2)

sets of RX (receive) and TX (transmit)

SC 100BASE-FX connectors to 1300

nm multimode fiber-optic cable.

C/E-R-TX-FX-01(SM)

Provides two (2) RJ-45 twisted pair

100BASE-TX connectors and two (2)

sets of RX (receive) and TX (transmit)

SC 100BASE-FX connectors to 1300

nm singlemode fiber-optic cable.

Power Modules

Media

Conversion

Center

Power

In Use

Power

In Use

Management

Module

Power

Link

CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO THE

PUBLIC TELEPHONE NETWORK. Failure to observe this caution could result in

damage to the public telephone network.

Der Anschluss dieses Gerätes an ein öffentlickes Telekommunikationsnetz in den EG-Mitgliedstaaten

verstösst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der Richtlinie 91/263/EWG zur

Angleichung der Rechtsvorschriften der Mitgliedstaaten über Telekommunikationsendeinrichtungen

einschliesslich der gegenseitigen Anerkennung ihrer Konformität.

C/E-R-TX-FX-01 in the Network . . . . . .2

Installation . . . . . . . . . . . . . . . . . . . .3

Operation . . . . . . . . . . . . . . . . . . . . .4

Fault Isolation and Correction . . . . .5

Cable Specifications . . . . . . . . . . . . .6

Technical Specifications . . . . . . . . . .7

Compliance Information . . . . . . . . . .8

C/E-R-TX-FX-01 IN THE NETWORK

Recessed switches located on each side of the media converter are used to

configure the media converter for the network.

NOTE: Switch labels are located

AT TOP of C/E-R-TX-FX-01 media converter.

MDI/MDI-X SWITCHES

(One for each RJ-45 port - located one on each side of media

converter) Allows straight-through twisted-pair cable to be

used for crossover 100BASE-TX connections.

4-POSITION SWITCH (3rd switch not used)

Auto-negotiation (UP) Detects and adapts to line speed and

operating mode of attached device.

Full/Half-duplex (UP) Allows an attached full-duplex station to

transmit and receive simultaneously. (DOWN) Allows an

attached station to transmit and receive sequentially.

Port Select Timer (UP) Selects timer duration of eleven (11) seconds.

(DOWN) Selects timer duration of five (5) seconds.

TECHNICAL SPECIFICATIONS

Standards IEEE 802.3

Case Dimensions 5.7" x 3.0" x 1.8" (145mm x 76mm x 46mm)

Shipping Weight 3 pounds (1.4 kilograms)

Delay 400nsec round trip

Environment Temperature: 0-50°C (32° to 122° F )

Humidity 10-90%, non condensing

Altitude 0-10,000 feet

Power Supply Requirements Replace power supply with only the equivalent

input rating (see below) and output rating (unregulated 9-24VDC, 5.5W).

TN PN Requirement Location

3507 240 volts, 50 hertz United Kingdom

3342 230 volts, 50 hertz Europe

3340 120 volts, 60 hertz USA/Canada/Mexico

3346 100 volts, 50-60 hertz Japan

3511 240 volts, 50 hertz Australia

3537 (with power cord: 3522) South Africa

Warranty Lifetime

NOTE: Media Converter Slide-in-Modules can be installed in any

installation slot, in any order.

DECLARATION OF CONFORMITY

Name of Mfg: Transition Networks

6475 City West Parkway, Minneapolis MN 55344 USA

Model: Redundant Fast Ethernet

™

Media Converters

Part Number: C/E-R-TX-FX-01

Regulation: EMC Directive 89/336/EEC

Purpose: To declare that the C/E-R-TX-FX-01 to which this declaration refers is

in conformity with the following standards.

EMC-CISPR 22: 1985 Class A; EN 55022: 1988 Class A; EN 50082-1:1992;

EN 60950 A4:1997; IEC 801.2, IEC 801.3, and IEC 801.4; IEC 950

I, the undersigned, hereby declare that the equipment specified above conforms to the

above Directive(s) and Standard(s).

_May 1, 1999_____

Stephen Anderson, Vice-President of Engineering Date

2 kilometers - multimode

20 kilometers - singlemode

100 meters

MDI switch setting

PST (DOWN) switch setting

MDI switch setting

PST (UP) switch setting

SWITCH

Do NOT connect media

converters between hubs.

Install no more than two (2)

media converters in series.

CABLE SPECIFICATIONS

The physical characteristics of the media cable must meet or exceed IEEE 802.3

specifications.

Fiber Cable

MULTIMODE

Fiber Optic Cable Recommended: 62.5 / 125 µm multimode fiber

Optional: 100 / 140 µm multimode fiber

85 / 125 µm multimode fiber

50 / 125 µm multimode fiber

Fiber Optic Transmitter Power: min: -19.0 dBm max: -14.0 dBm

Fiber Optic Receiver Sensitivity: min: -32.5 dBm max: -14.0 dBm

Wavelength : 850nM

Bit error rate: ≤10-9

Maximum Cable Distance: 2 kilometers

SINGLEMODE

Fiber Optic Cable Recommended: 9 µm singlemode fiber

Wavelength: 1300nM

Bit error rate: ≤10-9

Fiber-optic Transmitter Power: min: -15.0 dBm max: -8.0 dBm

Fiber-optic Receiver Sensitivity: min: -32.5 dBm max: -8.0 dBm

Maximum Cable Distance: 20 kilometers

Copper Cable

Category 5 twisted-pair copper wire is required. Either shielded twisted-

pair (STP) or unshielded twisted-pair (UTP) can be used. DO NOT USE

FLAT OR SILVER SATIN WIRE.

CATEGORY 5:

Gauge 24 to 22 AWG

Attenuation 20 dB/1000’ @ 10 MHz

Differential Characteristic Impedance 100 Ω ±10% @ 10 MHz

Maximum Cable Distance: 100 meters

INSTALLATION

Set Switches

Use small flatblade screwdriver or similar device to set recessed switches

according to site installation.

• Set EACH MDI/MDI-X switch to MDI for cable connection between switch

and media converter OR to MDI-X for cable connection between media

converter and terminal, transceiver or network interface card (NIC).

• Referring to drawing on page 2, set four-position switch according to

network configuration.

NOTE: If connecting two (2) media converters in series, set the PST (#4)

switch on one media converter to the UP position AND set the PST (#4)

switch on the other media converter to the DOWN position.

Install Slide-In-Module in E-MCC-1600 Chassis

• Remove Media Converter Slide-in-Module protective plate from

selected installation slot by removing two (2) screw that secures plate to

front of E-MCC-1600.

• Carefully slide Media Converter Slide-in-Module into installation slot,

aligning Media Converter Slide-in-Module with installation guides.

NOTE: Ensure that the Media Converter Slide-in-Module is firmly seated

against backplane.

• Secure Slide-in-Module by installing panel fastener screw attached to

Slide-in-Module.

Install Cable

COPPER

NOTE: KEEP TWISTED PAIR RUNS AS SHORT AS POSSIBLE.

• Locate or build 802.3 compliant cables with straight through

configuration and male RJ-45 plug connectors.

• Connect male RJ-45 plug connector at one end of cable to media

converter RJ-45 jack connector.

• Connect male RJ-45 plug connector at other end of cable to DTE

terminal RJ-45 jack connector (with MDI switch set to MDI-X) or to

switch RJ-45 jack connector (with MDI switch set to MDI).

FIBER

• Locate or build 802.3 compliant fiber cable with male two-stranded TX to

RX connectors appropriate to the media converter installed at both ends.

• Connect male TX and RX cable connectors at one end of cable to TX

and RX female connectors, respectively, on media converter.

• Connect male TX and RX cable connectors at other end of cable to RX

and TX connectors of 802.3 compliant fiber device.

(continued on next page)

The two active pairs in a 100BASE-TX

network are pins 1 & 2 and pins 3 & 6. Use

only dedicated wire pairs (such as

blue/white & white/blue, orange/white &

white/orange) for the active pins.

Twisted

Pair #1

Twisted

Pair #2

Straight Through Cable

INSTALLATION

(continued)

Connect to Power

• Install Power Adapter cord at back of media converter.

• Connect Power Adapter 3-prong plug to AC power.

• Verify that media converter is powered by observing illuminated LED(s).

OPERATION

After installation, the media converter should function without operator

intervention.

Status LEDs:

Use the status LEDs to monitor media converter operation in the network.

NOTE: lluminated PRI(mary) and/or SEC(ondary)

LEDs indicate media converter connection to

external power.

PRI Copper Primary Port - Steady green

LED indicates primary copper port is

being selected

by internal

control logic

SEC Copper

Secondary Port -

Steady green

LED indicates

secondary

copper port is

being selected

by internal control logic

RXC Receive Copper Port - Steady green

LED indicates valid data is being

detected on copper interface

SDC Signal Detect Copper - Steady green LED indicates Link

established on copper port selected

PRI: Fiber Primary Port - Steady green LED indicates primary fiber

port is being selected by internal control logic

SEC Fiber Secondary Port - Steady green LED indicates secondary

fiber port is being selected by internal control logic

SDF Signal Detect Fiber - Steady green LED indicates optical signal

present on fiber port selected

RXF Receive Fiber Port - Steady green LED indicates non-IDLE

symbols are being detected on fiber interface

FAULT ISOLATION and CORRECTION

If the media converter fails, isolate and correct the failure by determining the

answers to the following questions and then taking the indicated action:

1. Are the PRI(mary)/SEC(ondary) LEDs on the media converter

illuminated or alternating between between primary and

secondary ports?

• Is the power adapter the proper type of voltage and cycle frequency

for AC outlet?

NOTE: Refer to the “Power Supply Requirements” on page 7.

• Is the power adapter properly installed in the media converter and

in the outlet?

• *Are PST switch settings on two media converters installed in series

in the network set to different values?

• Contact Technical Support at (800) 260-1312/ (800) LAN-WANS.

YES

• Proceed to step 2.

2. Is the 100BASE-TX SDC (Signal Detect/Copper) LED

illuminated?

• Check UTP cables for proper connection.

• Verify MDI/MDI-X switch position.

• Contact Technical Support at (800) 260-1312/ (800) LAN-WANS.

YES

• Proceed to step 3.

3. Is the 100BASE-FX SDF (Signal Detect/Fiber) LED illuminated?

• Check fiber cables for proper connection.

• Verify that TX and RX cables on media converter are connected to

RX and TX ports, respectively, on the other 100BASE-FX device.

• Refer to Tech Tips available at: http://www.transition.com

• Contact Technical Support at (800) 260-1312/ (800) LAN-WANS.

YES

• Contact Technical Support at (800) 260-1312/ (800) LAN-WANS.

*NOTE: Setting PST switch settings on two media converters installed in series

in the network to different values (11 seconds and 5 seconds) ensures, in the

event of common power failure or similar incident, a sufficient delay in the time

required to establish each link so that communication between the media

converters is guaranteed.

PrimaryPrimary

100BASE-TX100BASE-TX

PrimaryPrimary

100BASE-FX100BASE-FX

SecondarySecondary

100BASE-TX100BASE-TX

SecondarySecondary

100BASE-FX100BASE-FX

RXC

RXF

SDF

SDC

PRI

SEC

PRI

SEC

RXC

SDC

PRI

SEC

RXF

SDF

SEC

PRI

Transition Networks Switch CERTXFX01(SM) Manuel utilisateur

Marque: Transition Networks

Modèle: Switch CERTXFX01(SM)

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Transition Networks Switch CERTXFX01(SM) User manual

Transition Networks Switch CERTXFX01(SM) Manuel utilisateur

Ce manuel convient également à

Transition Networks Switch CERTXFX01(SM) Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents