Transition Networks J/FE-CF-04 SMLC Manuel utilisateur

Catégorie
Convertisseurs de média réseau
Taper
Manuel utilisateur
USER’S GUIDE
J/FE-CF-04 Stand-Alone Media
Converter
Fast Ethernet™
Copper to Fiber
100Base-TX to 100Base-FX
USB Port
Transition Networks J/FE-CF-04 Fast
Ethernet™ media converter connects 100
Mb/s twisted-pair copper cable to a duplex
100 Mb/s fiber-optic cable.
Use the J/FE-CF-04 series media
converters to extend over fiber, the distance between two 100BASE-TX devices (hub,
switch, workstation, etc.).
Part Number Port One - Copper Port Two - Duplex Fiber-Optic
J/FE-CF-04 RJ-45, 100Base-TX
100 m (328 ft)*
ST, 100Base-FX, 1300 nm multimode
2 km (1.2 miles)*
J/FE-CF-04(SC) RJ-45, 100Base-TX
100 m (328 ft)*
SC , 100Base-FX, 1300 nm multimode
2 km (1.2 miles)*
J/FE-CF-04(LC) RJ-45, 100Base-TX
100 m (328 ft)*
LC, 100Base-FX, 1300 nm multimode
2 km (1.2 miles)*
J/FE-CF-04(SM) RJ-45, 100Base-TX
100 m (328 ft)*
SC, 100Base-FX, 1310 nm single mode
20 km (12.4 miles)*
J/FE-CF-04(SMLC) RJ-45, 100Base-TX
100 m (328 ft)*
LC, 100Base-FX, 1310 nm single mode
20 km (12.4 miles)*
J/FE-CF-04(LH) RJ-45, 100Base-TX
100 m (328 ft)*
SC, 100Base-FX, 1310 nm single mode
40 km (24.9 miles)*
*Typical maximum cable distance. Actual distance is dependent upon the physical
characteristics of the network installation.
Installation . . . . . . . . . . . . . . . . . . . . .3
Operation . . . . . . . . . . . . . . . . . . . . . .6
Cable Specifications . . . . . . . . . . . . .7
Technical Specifications . . . . . . . . . .8
Troubleshooting . . . . . . . . . . . . . . . .9
Contact Us . . . . . . . . . . . . . . . . . . . .10
Compliance Information . . . . . . . . .11
2
J/FE-CF-04-xxx
24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
Part Number Description
WMBD Optional Din-Rail Mount
Length: 4.9 in. (124.46 mm) Fits converter length: 3.9 in. (99 mm)
WMDB-FS Optional Din-Rail Mount
Width: 3.1 in. (78.7 mm) Fits converter width: 3.0 in (78 mm)
WMBS Optional Wall Mount Brackets
Length: 3.2 in. (81 mm), Fits converter length: 3.9 in. (99 mm)
SPS-1872-SA Optional External Power Supply; 18-72VDC Stand-Alone Wide-
Input; Output: 12.6VDC, 1.0 A
SPS-1872-CC Optional External Power Supply; 18-72VDC Piggy-Back Wide-Input;
Output: 12.6VDC, 1.0 A
Options Accessories (sold separately)
Part Number Port One - Copper Port Two - Duplex Fiber-Optic
J/FE-CF-04-100 RJ-45, 100Base-TX
100 m (328 ft)*
SC, 1310 mn TX/1550 nm RX, 20 km
(12.4 miles)*
J/FE-CF-04-101 RJ-45, 100Base-TX
100 m (328 ft)*
SC, 1550 mn TX/1310 nm RX, 20 km
(12.4 miles)*
Note: Install the J/FE-CF-04-100 and the J/FE-CF-04-101 in the same network as
local and remote peers.
Single Fiber Optic (install in pairs)
*Typical maximum cable distance. Actual distance is dependent upon the physical
characteristics of the network installation.
3
[email protected] -- Click the “Transition Now” link for a live Web chat.
Installation
Installing the Cable
Fiber
1. Locate a 100Base-FX compliant, two-strand fiber cable with the appropriate
male connectors installed on both ends.
2. Connect the fiber cable to the J/FE-CF-04 media converter and to its mating
device as shown below.
Connect fiber cable
to media converter
as shown.
Connect fiber cable
to other device
(media converter,
hub, etc.) as shown
RX
TX
RX
TX
Connect fiber cable
to the J/FE-CF-100
media converter
Connect fiber cable
other end to the
J/FE-CF-101
media converter
RX
TX
RX
TX
100 101
Installing single-fiber cable to matched pair converters
1. Locate a 10Base FX compliant, single-strand fiber cable with the appropriate
male connectors installed on both ends.
2. Connect the single fiber cable to the matched pair converters as shown below.
4
J/FE-CF-04-xxx
24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
Setting the two-position DIP switch
A two-position DIP switch (located on the back of the media converter) supports
selecting Auto-Negotiation and Full- or Half-Duplex. Typically, most installation
will work with both switches in the UP position. Use a small, flat-blade screwdriver
(or a similar device) to set the switches according to the site requirements; see the
illustration and explanation below.
Auto-Negotiation:
UP Enable Auto-Negotiation
DOWN Disable Auto-Negotiation
Full/Half Duplex (functions only when Auto-Negotiation is enabled.)
UP Full Duplex -- Advertises 100 Mb/s full-duplex only during Auto-
Negotiation.
DOWN Half Duplex -- Used primarily when connecting to a hub. Operates at
100 Mb/s in duplex mode of the attached device.
Note: The configuration of the DIP switches should match that of the RJ-45 port
configuration of the connecting device
Full/Half Duplex - UP=Full
Auto-Negotiation - UP=Enable
Installation -- Continued
Copper
1. Locate or build 100Base-TX compliant copper cable with male, RJ-45
connectors installed at both ends.
2. Connect one end of the RJ-45 cable to the J/FE-CF-04 media converter and
the other end to its mating device as shown below.
RJ-45 port
on the other device
(switch, work station, etc.)
RJ-45 port
on the media
converter
5
[email protected] -- Click the “Transition Now” link for a live Web chat.
Installation -- Continued
Powering the media converter
DC power adapter:
1. Insert the power adapter barrel into the barrel connector located on the back of
the media converter, shown above.
2. Connect the power adapter plug into AC power.
3. Observe that the power ON LED is lit.
USB port power:
Use a USB 2.0 Type A to B male-to-male cable to enable powering the media
converter via an active USB port.
Note: When using the USB port to power the media converter, make sure that the
output USB port is turned ON (some laptops and PCs can turn OFF the
USB port).
The media converter can also be powered via the USB port. When powering the
media converter with the power adapter and through the USB power, the media
converter has redundant power (no load balancing which means the device draws
operating current from higher voltage source, adapter or USB). If the power
adapter is removed, the media converter will be powered via the active USB port.
Note: The USB port provides power to the device only; it is not used to transfer
data.
Rear Panel
Male Input Power Port
Barrel Connector
USB Port
DIP
Switches
6
J/FE-CF-04-xxx
24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
Fiber
TX RX
Copper
Pwr
Front Panel
100Base-FX 100Base-TX
Operation
Using status LEDs
Use the status LEDs to monitor the media converter operation in the network.
Power LED ON indicates connection to adapter power or USB power.
Fiber LED ON indicates fiber link connection.
Copper LED ON indicates copper link connection.
LED FLASHING indicates activity.
Auto-Negotiation
The Auto-Negotiation feature allows the media converter to be used with
10/100Base-TX ports. When using Auto-Negotiation, the media converter brings up
the copper link to the highest speed and best duplex mode possible for all attached
network devices.
Full-Duplex network
In a full-duplex network, maximum cable lengths are determined by the type of
cables that are used. (The 512-Bit Rule does not apply in a full-duplex network.) See
front cover for available J/FE-CF-04 models.
Half-Duplex network (512-Bit Rule)
In a half-duplex network, the maximum cable lengths are determined by the round
trip delay limitations of each Fast Ethernet collision domain. (A collision domain is
the longest path between any two terminal devices, e.g., a terminal, switch, router,
etc.)
The 512-Bit Rule determines the maximum length of cable permitted by calculating
the round-trip delay in bit-times (BT) of a particular collision domain. If the result
is less than or equal to 512 BT, the path is good.
For more information on the 512-Bit Rule, see the white paper titled “Collision
Domains” on the Transition Networks website at:
http://www.transition.com/learning/white papers
Cable Specifications
The physical characteristics must meet or exceed IEEE 802.3™ specifications.
Fiber cable
Bit Error Rate: <10-9
Singlemode fiber (recommended): 9 μm
Multimode fiber (recommended): 62.5/125 μm
Multimode fiber (optional): 100/140, 85/140, 50/125 μm
J/FE-CF-04 1300 nm multimode
Fiber Optic Transmitter Power: min: -19.0 dBm max: -14.0 dBm
Fiber Optic Receiver Sensitivity: min: -30.0 dBm max: -14.0 dBm
Link Budget: 11.0 dB
J/FE-CF-04(SC) 1300 nm multimode
Fiber Optic Transmitter Power: min: -19.0 dBm max: -14.0 dBm
Fiber Optic Receiver Sensitivity: min: -30.0 dBm max: -14.0 dBm
Link Budget: 11.0 dB
J/FE-CF-04(LC) 1300 nm multimode
Fiber Optic Transmitter Power: min: -19.0 dBm max: -14.0 dBm
Fiber Optic Receiver Sensitivity: min: -30.0 dBm max: -14.0 dBm
Link Budget: 11.0 dB
J/FE-CF-04(SM) 1310 nm single mode
Fiber Optic Transmitter Power: min: -15.0 dBm max: -8.0 dBm
Fiber Optic Receiver Sensitivity: min: -31.0 dBm max: -8.0 dBm
Link Budget: 16.0 dB
J/FE-CF-04(SMLC) 1310 nm single mode
Fiber Optic Transmitter Power: min: -15.2 dBm max: -8.0 dBm
Fiber Optic Receiver Sensitivity: min: -32.5 dBm max: -3.0 dBm
Link Budget: 17.3 dB
J/FE-CF-04(LH) 1310 nm single mode
Fiber-optic Transmitter Power: min: -8.0 dBm max: -2.0 dBm
Fiber-optic Receiver Sensitivity: min: -34.0 dBm max: -7.0 dBm
Link Budget: 26.0 dB
J/FE-CF-04-100 1310 nm (TX)/1550 nm (RX) simplex
J/FE-CF-04-101 1550 nm (TX)/1310 nm (RX) simplex
Fiber-optic Transmitter Power: min: -13.0 dBm max: -6.0 dBm
Fiber-optic Receiver Sensitivity: min: -32.0 dBm max: -3.0 dBm
Link Budget: 19.0 dB
7
[email protected] -- Click the “Transition Now” link for a live Web chat.
Operation -- continued
AutoCross™
The AutoCross feature allows the use of straight-through MDI or crossover MDI-X
cables for connecting to10Base-T or 100Base-TX devices. AutoCross determines
the characteristics of the connection and automatically configures the unit to link
up, regardless of the cable configuration: MDI or MDI-X. This feature is
permanently enabled.
Copper cable
Category 5:
Gauge: 24 to 22 AWG
Attenuation: 22.0 dB/100m @ 100 MHz
Maximum Cable Distance: 100 meters
Straight-Through or Crossover cable may be used.
• Shielded Twisted-Pair (STP) or Unshielded Twisted-Pair (UTP) may be used.
• Pins 1&2 and 3&6 are the two active pairs in an Ethernet™ network .
• Use only dedicated wire pairs for the active pins:
(e.g., blue/white & white/blue, orange/white & white/orange, etc.)
• Do not use flat or silver satin wire.
8
J/FE-CF-04-xxx
24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
Technical Specifications
For use with Transition Networks Model J/FE-CF-04 or equivalent
Product is certified by the manufacturer to comply with DHHS Rule 21/CFR,
Subchapter J applicable at the date of manufacture.
Standards: IEEE 802.3™
Data Rate: 100 Mb/s
Case Dimensions: 3.9" x 3.0" x 1.0" (100mm x 76mm x 25mm)
Shipping Weight: 2 pounds (0.9 kilograms)
Power Consumption: 2.4 watts, 200 mA @ 12 VDC
Input Voltage:
• AC/DC Adapter: 12 VDC, 0.5 A output
minimum output regulation: 5% connector:
2.1mm barrel, center pin positive
• USB 2.0 Port: 5 VDC, 0.5A
MTBF* 48,135 hours
(MIL217F2 V5.0) (MIL-HDBK-217F)
128,553 hours (Bellcore7 V5.0)
Environment:
Tmra**: 0 to 60°C (32 to 140°F)
Storage Temp: -20 to 85°C (-4 to 185°F)
Humidity: 5-95%, non-condensing
Altitude: 0-10,000 feet
Warranty: Lifetime
*MTBF is estimated using the predictability method. This method is based on MIL-
217F at 25°C ambient temperature, typical enclosure heat rise of 10°C, and nominal
operating conditions and parameters. Installation and configuration specific MTBF
estimates are available upon request. Contact Technical Support.
**Manufacturer’s rated ambient temperature.
9
[email protected] -- Click the “Transition Now” link for a live Web chat.
Troubleshooting
If the media converter fails, isolate and correct the failure by determining the answers
to the following questions and then taking the indicated action:
1. Is the Power LED on the media converter illuminated?
NO
Is the power adapter the proper type of voltage and cycle frequency for
the AC outlet?
Is the power adapter properly installed in the media converter and in the
outlet?
Is the external power source active and at the proper voltage level?
If powering the device via the USB port, make sure that the USB cable is
properly connected at both ends and that the USB port is powered up.
Contact Technical Support at (800) 260-1312.
YES
Proceed to step 2.
2. Is the Copper LED illuminated?
NO
Check the copper cable for proper connection.
Contact Technical Support at (800) 260-1312.
YES
Proceed to step 3.
3. Is the Fiber LED illuminated?
NO
Check the fiber cables for proper connection.
Verify that the TX and RX cables on the media converter are connected to
the RX and TX ports, respectively, on the other 100BASE-FX device.
Contact Technical Support at (800) 260-1312.
YES
Contact Technical Support at (800) 260-1312.
Technical Specifications -- continued
WARNING: Visible and invisible laser radiation when open. Do not stare into the
beam or view the beam directly with optical instruments. Failure to observe this
warning could result in an eye injury or blindness.
WARNING:
Use of controls, adjustments or the performance of procedures other
than those specified herein may result in hazardous radiation exposure.
CAUTION:
Copper based media ports, e.g., Twisted Pair (TP) Ethernet, USB,
RS232, RS422, RS485, DS1, DS3, Video Coax, etc., are intended to be connected to
intra-building (inside plant) link segments that are not subject to lightening transients
or power faults. Copper based media ports, e.g., Twisted Pair (TP) Ethernet, USB,
RS232, RS422, RS485, DS1, DS3, Video Coax, etc., are NOT to be connected to
inter-building (outside plant) link segments that are subject to lightening transients or
power faults. Failure to observe this caution could result in damage to equipment.
10
J/FE-CF-04-xxx
24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
Declaration Of Conformity
Name of Mfg: Transition Networks
6475 City West Parkway, Minneapolis MN 55344 U.S.A.
Model: J/FE-CF-04 Series Media Converters
Part Number(s): J/FE-CF-04; J/FE-CF-04(SC); J/FE-CF-04(LC); J/FE-CF-04(SC),
J/FE-CF-04(LC); J/FE-CF-04(LH); J/FE-CF-04-100,
J/FE-CF-04-101
Regulation: EMC Directive 89/336/EEC
Purpose: To declare that the J/FE-CF-04-xxx to which this declaration refers
is in conformity with the following standards.
EN 55022:1994; EN 55024:1998; FCC Part 15 Class A;
A4:1997; 21 CFR subpart J
I, the undersigned, hereby declare that the equipment specified above conforms to the
above Directive(s) and Standard(s).
July, 2007_____
Stephen Anderson, Vice-President of Engineering Date
Contact Us
Technical support
Technical support is available 24 hours a day.
US and Canada: 1-800-260-1312
International: 00-1-952-941-7600
Transition NOW
Chat live via the Web with Transition Networks Technical Support.
Log onto www.transition.com and click the Transition Now link.
Web-Based seminars
Transition Networks provides seminars via live web-based training.
Log onto www.transition.com and click the Learning Center link.
E-Mail
Ask a question anytime by sending an e-mail to our technical support staff.
Address
Transition Networks
6475 City West Parkway
Minneapolis, MN 55344, U.S.A.
telephone: 952-941-7600
toll free: 800-526-9267
fax: 952-941-2322
11
[email protected] -- Click the “Transition Now” link for a live Web chat.
Compliance Information
Power Supply UL Listed
Power Supply C-UL Listed (Canada)
CE Mark
FCC Regulations
This equipment has been tested and found to comply with the limits for a class A digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference, in which
case the user will be required to correct the interference at the user's own expense.
Canadian Regulations
This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out
on the radio interference regulations of the Canadian Department of Communications.
Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables
aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage
radioélectrique édicté par le ministère des Communications du Canada.
European Regulations
Warning
This is a Class A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.
Achtung !
Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können bei Betrieb dieses
Gerätes Rundfunkstörungen auftreten, in weichen Fällen der Benutzer für entsprechende
Gegenmaßnahmen werantwortlich ist.
Attention !
Ceci est un produit de Classe A. Dans un environment domestique, ce produit risque de créer des
interférences radioélectriques, il appartiendra alors à l'utilsateur de prende les measures spécifiques
appropriées.
In accordance with European Union Directive 2002/96/EC of the European Parliament
and of the Council of 27 January 2003, Transition Networks will accept post usage
returns of this product for proper disposal. The contact information for this activity can
be found in the 'Contact Us' portion of this document.
CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO THE
PUBLIC TELEPHONE NETWORK. Failure to observe this caution could result in
damage to the public telephone network.
Der Anschluss dieses Gerätes an ein öffentlickes Telekommunikationsnetz in den EG-
Mitgliedstaaten verstösst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der
Richtlinie 91/263/EWG zur Angleichung der Rechtsvorschriften der Mitgliedstaaten über
Telekommunikationsendeinrichtungen einschliesslich der gegenseitigen Anerkennung ihrer
Konformität.
12
Trademark Notice
All trademarks and registered trademarks are the property of their respective owners.
Copyright Restrictions
© 2003 Transition Networks.
All rights reserved. No part of this work may be reproduced or used in any form or by any means -
graphic, electronic, or mechanical - without written permission from Transition Networks.
Printed in the U.S.A. 33372.B
J/FE-CF-04-xxx
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

Transition Networks J/FE-CF-04 SMLC Manuel utilisateur

Catégorie
Convertisseurs de média réseau
Taper
Manuel utilisateur

dans d''autres langues