NewAge Products 65467 Guide d'installation

1

STOP

Use two or more people to move, assemble, or

install cabinets to avoid back injury. Do not

leave children unattended near cabinets. High

risk of tipping if cabinets are installed

incorrectly: securely attach cabinets to the

wall to avoid serious injury. For assistance, call

1.877.306.8930; for U.K 0800.031.4069: e-mail at

info@newageproducts.com.

ATTENTION: Is your cabinet damaged?

Need help or spare parts? For fastest service,

contact NewAge Products at 1-877-306-8930;

or suppor[email protected]om.

Do not return to the retailer.

Warning: Excessive weight

hazard!

65400-Series Cabinets

Outdoor Kitchen Aluminum

Coastal Gray Series Cabinets

32”- 2 Door

32”- Sink

32”- 3 Drawer

28”- Kamado

32”- Bar

32”- Wall

45 Degree 90 Degree

33” Insert Grill Cabinet

40” Insert Grill Cabinet

2

Weight

Capacity

200 lbs.

115 lbs.

32" - 2 Door Cabinet

200

lbs.

Max 630 lbs.

Weight

Capacity

100 lbs.

75 lbs.

200 lbs.

32" - Sink Cabinet

Max 375 lbs.

Weight

Capacity

75

lbs.

75

lbs.

32” - 3 Drawer Cabinet

200 lbs.

Max 425 lbs.

75

lbs.

75

lbs.

200 lbs.

32" - SS Bar Cabinet

Max 350 lbs.

Weight

Capacity

Weight

Capacity

100 lbs.

50 lbs.

100 lbs.

Max 300 lbs.

Weight

Capacity

100 lbs.

50lbs.

50 lbs.

90˚ Corner Shelf

Max 200 lbs.

Weight

Capacity

200

lbs.

115

200

33” - BBQ SS

Max 515 lbs.

BBQ

Weight

Capacity

200

lbs.

115

200

40” - BBQ SS

Max 515 lbs.

BBQ

Weight

Capacity

100 lbs.

300 lbs.

28” - KAMADO Cabinet

75

lbs.

Max 475 lbs.

Weight

Capacity

50lbs.

75

lbs.

75

lbs.

32" - Wall Cabinet

Max2 00 lbs.

3

56” Worktop. Fits over 1 Cabinet

& Fridge nook.

88” Worktop. Fits over 2 Cabinets

& Fridge nook.

64” Worktop. Fits over 2 Cabinets

Worktops

96” Worktop. Fits over 3 Cabinets

16”

Unpacking

• Begin by placing the package on a protected at

surface.

• Remove all cardboard, foam packaging material and

clear plastic bags.

• Dispose / recycle all packaging materials.

• Verify all the contents in the box and gather the re-

quired tools. See “Parts” and “Tools Needed” in the

list below.

4

Limited Warranty:

All products must be installed, operated, and maintained in accordance with the instructions included with

the products. If a product is properly installed, operated, and maintained fails to meet the below limited

warranty, NewAge Products, Inc (“NewAge”) will replace the defective product or parts.

Subject to the limitations and disclaimers set forth below or in other product documentation, NewAge

warrants to the initial customer that (1) product nishes will be free from defects for three years following

purchase, (2) drawer slides will be free from defects for two years following purchase, and (3) the overall

structural integrity of the product (not including nishes or drawer slides) will be free from defects for ten

years following purchase.

Customer must pay for shipping costs associated with any replacement product or parts. This limited

warranty is limited to product replacement only. In no event will NewAge be liable for special, indirect, or

consequential damages.

This limited warranty is available to the initial purchaser only and is not transferable. Proof of purchase and

additional information regarding the defect may be required at NewAge’s discretion. The warranty is made

only to products sold in the continental United States, Canada, and the United Kingdom.

ALL OTHER WARRANTIES DISCLAIMED:

ALL OTHER WARRANTIES ARE DISCLAIMED TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW.

WITHOUT LIMITING THE GENERALITY OF THE FORGOING, NEWAGE EXPRESSLY DISCLAIMS ANY IMPLIED

WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

NEWAGE PRODUCTS INC. WILL NOT PAY FOR:

1. Service calls or labor costs.

2. Products damaged by accident, misuse, abuse, re, ood, improper installation, acts of God, neglect,

corrosion, improper maintenance or cleaning, modication, mishandling or not following

care instructions.

3. Products damaged by improperly loading beyond the specied maximum weight capacity outlined

in the instructions provided with the product.

4. Defects results from use in excess of normal residential use.

5. Cosmetic damage that occurs after customer purchasing the product, including scratches, dings,

dents, corrosion, or stains in the material that does not aect the structural or functional capability

of the product.

6. Loss of product contents.

5

4 x Handle Bolts

(M4 x 30mm)

4 x Hex Nuts

(M5)

Parts Supplied

4 x Height-Adjustable

Levelers

Stainless Steel Handles

2 x Garbage Bins

4 x Hex Bolts

(M6 X 2mm)

8 x Shelf Clips

Full Width

Adjustable

Shelves

4 x Hex Bolts

(M5 x 50mm)

1 x Ice Tray

4 x

Utility Trays

1 x Wine Rack

Pair of

Grill Mounting

Brackets

Pair of

Inside Grill

Mounting Brackets

2” Filler 1 1/2”” Filler

1” Filler

6 x

Filler Brackets Left and

Right Side

34 x Pan Head Bolts

(M4x .7 x 10mm)

1 x Drilling Template

2 x Anti Tipping

Brackets

6 x Tapcon

Screws

6 x Wood

Screws

Type Hardware

32"‐2

DoorBase

32"Sink

Cabinet

32"‐3

Drawer

32"‐Bar 33"Grill 40"Grill

28"

Kamado

45

Degree

90

Degree

Wall

Cabinet

HandleBolts(M4x25) 4 4 6 6 4 4 2 4 0 2

HexBolt(M6x50mm) 4 4 4 4 4 4 4 8 8 8

HexBolt(M6x12mm) 0 0 0 0 0 4 0 0 0 0

PanHeadBolt(M4x.7x10MM) 0 0 0 0 0 0 0 0 34 0

HexNuts(M6) 4 4 4 4 4 4 4 0 8 8

FlatWasher(M6) 0 0 0 0 0 0 0 0 8 0

TapconScrews 0 0 0 0 0 0 6 0 0 0

WoodScrews(4.2x16) 0 0 0 0 0 0 6 0 0 0

DrillingTemplate 0 0 0 0 0 0 1 0 0 0

ShelfClips 8 4 0 4 0 0 4 0 0 4

20 16 14 18 12 16 27 12 58 22

PlasticHoleCaps 8 8 8 8 8 8 8 0 0 8

Height‐AdjustableLevelers 4 4 4 4 4 4 4 8 4 4

12 12 12 12 12 12 12 8 4 12

IceTray 0 0 0 1 0 0 0 0 0 0

WineRack 0 0 0 1 0 0 0 0 0 0

UtilityTrays 4 0 0 4 4 4 0 0 0 0

DrawerPartitions 1 0 4 4 0 0 0 0 0 0

StainlessSteelHandles 2 2 3 3 2 2 1 2 0 0

GarbageBin 0 0 0 2 0 0 0 0 0 0

AdjustableShelves 2 1 0 0 0 0 0 0 0 1

SinkDryingRack 0 1 0 0 0 1 0 0 0 0

9 4 7156 7 1 201

GraniteInstalationRails 0 0 0 0 0 0 0 0 2 0

FillerBrackets 0 0 0 0 6 6 0 0 0 0

GrillInsideBracket 0 0 0 0 0 2 0 0 0 0

GrillMountingBracket 0 0 0 0 2 2 0 0 0 0

AntiTippingBracket 0 0 0 0 0 0 2 0 0 0

0 0 0 0810 2 020

IncludedBrackets

IncludedComponents

HardwarePack

AdditionalHardware

6

OTHER NOTES TO CONSUMER:

Discoloration due to the high heat, for example beside a grill, is a trait of stainless steel and is not covered.

Surface rust resulting from acid rain or environmental chemicals are not covered. (Please see maintenance

information to combat surface rust). NewAge outdoor powder coated nishes are designed to withstand

weathering and are UV stable.

The 304 stainless steel material used in the construction of NewAge Outdoor Kitchen Cabinets is highly rust

resistant, however, chlorine in the air from swimming pools or the salt from sea air may cause surface rust

to appear and even create some pitting corrosion if left on the product. We strongly recommend a suitable

maintenance tested product. We suggest cleaning all stainless steel surfaces at least every two weeks to

keep your cabinets in prime condition. The chemical reaction from salt is easy to prevent however it is more

dicult when left on the surface.

Additional product information is available at

http://www.newageproducts.com/outdoor-kitchen-limited-warranty

Tools Needed

1 x #2 Phillips Bit

1 x Tape Measure

1 x Flashlight

1 x 24” Level

1 x 10mm socket 1 x Socket wrench

1 x Cordless Power Drill

1 x Adjustable wrench

1 x 10mm Open end wrench

1 x #2 Phillips head

screwdriver

7

Installing the Handles

Parts Needed.

Align handle to holes on doors

Handle

or drawers.

Handle Bolt

M4 x 25mm

3

Screw in bolts.

8

Raise Height

Lower Height

Adjusting the Levelers

1

Flip ver Cabinet to reveal bottom.

2

Stand cabinet upright. Level Cabinet.

Open cabinet, remove any shelves

or loose items.

Repeat step 3 for each corner.

5

4

Parts Needed.

4 X Adjustable

Levelers

Rotate Leveler counter clockwise

to raise height.

3

Lower Height

Raise Height

9

Installing the Casters (Sold Separately)

1

Remove8- M4 x 25mm bolts in locations

with phillips screw driver accessed

through holes in kick.

2

Rotate cabinet until all 4 casters are resting

on the ground..

Open cabinet, remove any shelves

or loose items.

1

2

3

4

5

6

7

8

Place caster plate over 4 rivet nuts in 4 cor-

ner locations install/ tighten 16 x 1/4” x 1/2”

bolts. Can be installed with socket or Phillips

drive.

5

4

Parts Needed.

Remove Kick and store with hardware

for future conguration considerations.

3

4 X Casters

16 X Hex

Bolts

10

Fastening Cabinets(to each other)

Align bolts, tighten lightly.

Level cabinets and tighten all bolts.

X4

1

2

X8

Remove plastic caps from cabinets.

3

4

Parts Needed.

4 X Hex Bolt

(M5 x 50mm”)

4 X Hex Nut(M5)

11

Mounting the Worktop

1

Place worktop over cabinets.

2

Insert the worktop bolt heads

into the keyhole shape slots.

Tighten screws to secure cabi-

nets.

Stand cabinet upright.

3

Push worktop in to lock.

4

Optional: Repeat steps 2-5 for mounting

larger worktops.

5

12

Inserting Cabinet Shelves

1

Insert and position above shelf clips.

Lower shelf down onto shelf clips.

2

Begin with shelf being level.

Install remaining shelves.

Open cabinet doors. Attach

shelf clips to desired height.

4

3

5

13

Adjusting The Door Hinges

1

A

Using a Philips screwdriver, the doors can be adjusted:

Left, right, forwards and backwards.

To adjust the doors left or right, turn the screw (A) clockwise or counterclockwise.

To adjust the gap between the doors and frame, turn the screw (B)

clockwise or counterclockwise.

2

Thank you for purchasing a NewAge Product!

Please give us a call or visit online if you have any questions.

Call 1.877.306.8930; for UK 0800.031.4069; e-mail at info@newageproducts.com

B

14

Installing the Drawers Removing Drawers.

1

Inserting Drawers.

Right Side

Left Side

Slide In

Slide Ou t

Align R ails

Inserting Drawers.

3 Drawer Specic Instructions

15

Floor

Drill Floor in marked positions

with appropriate drill for substrate.

1 X Measuring Tape

1

Parts Needed.

1 X Pencil

Hammer drill and bit

6 X Wood Screws

6 X Tapcon Screws

2 X Hold down Brackets

1 x Marking Template

2

Place Marking template on your

indicating where to place your cabinet.

Mark 6 drill locations using

Step 1

template to place brackets

Floor

Wall Or Structure

Fasten Floor Brackets with

3 Tapcons(concrete) 3 wood

screws (wood)

Move cabinet glides into

brackets to secure cabinet

3 Drawer Specic Instructions

16

ing the anti tip brackets

1

Determine the location of your cabinet

Drill with appropriate

2

4

Once both brackets are attached to the

the back to engage brackets with the levelers

3

using the appropriate driver bit

3

Both Levelers should now be

captured by bracket

6

Next step install Kamado into cabinet

5

Front of Kamado

Kamado Specic Instructions

17

Kamado Specic Instructions

ing the

5

Protect surface with cloth or cardboard

into cabinet

Rotate handle until it is parallel with

front of cabinet

1

Measure From Base of Kamado to

bottom of lid bracket at rear of unit.

GROUND

0 in.1 2 345678910 11 12

23456789 10 11 12

23

4

56

7

8910

11

12 2

3

456789

10

11

12

1230 cm.456789101112131415161718192021222324252627282930

5678

9

10 11 12 13 14

15

16 17 18 19 20

21

22 23 24 25 26

27

28 29

6

30

578 9 10 11 12 13 14 15

16 17 18 19 20 21 22 23 24 25 26 27 28 29 630 5 7 8910 11 12 13 14 15 16 17 18 19

20 21 22 23 24 25 26 27 28 29

30

Adjust shelf height to dimension from

2

18”

16”

gnidrocca gnir retemaid eht tceleS

3

to Kamado size and test from step 2

16” Kamado

3

18” Kamado

21” Kamado

18

1

Wine Rack, Ice Tray

and Garbage Bin Installation

Set rack on top of 4 clips at the same

2

level height. Store beverage bottles.

Remove and install Garbage bins

Remove and install beverage chilling

tray with formed metal edge.

3

Open Doors. Set rack clips in the

desired slot locations on the

upright posts.

Slide beverage chilling tray into/out of

pullout frame. Push in frame to dock.

4

Slide Garbage bins into/out of pullout

frame. Push in frame to dock.

5

6

Bar Specic Instructions

19

Plumbing Installation

Locate the 3 pre slotted holes in the back of the cabinet.

Using tin snips cut small webs to release the knockouts.

Locate the 3 pre slotted holes in the bottom

of the cabinet.

Using tin snips cut small webs to release the knockouts.

123

Back View of Sink Cabinet.

Bottom View of Sink Cabinet.

1 1/2”NPT

pipe

male drain

perform installation

Connect the drain trap adapter to

a p-trap and drainage tubing.

3/8” COMP Female hose end

Connect the braided water inlet

lines hot and cold to the supply

lines.

3/8” COMP male valve end

10mm

Elbow/ P- Trap

Sink Specic Instructions

20

Push down to lock

Push to unlock

Installing the BBQ

1

Place BBQ so that the rails touch

to hold it in place.

You may or may not need the

adapter brackets depending on

the model BBQ you choose.

Parts Needed.

Silicone

2 X Adapter Brackets

Turn Wing nut bolt until tank ring

clamp engages with bottom tank ring

4

Once tank tray it pushed to the back

of the cabinet, lock the tank tray by

pushing down on the lock button.

Push the release button to unlock.

Grills and Side Burner Specic Instructions

La page est en cours de chargement...

NewAge Products 65467 Guide d'installation

Ce manuel convient également à

NewAge Products 65467 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents