Impecca IWA25-KS30 Mode d'emploi

Marque: Impecca

Modèle: IWA25-KS30

Catégorie: Climatiseurs mobiles

Taper: Mode d'emploi

Electronic Window Air Conditioner with Remote—User's Guide

Models:

IWA06-KR15, IWA08-KR15, IWA10-KR15, IWA12-KR15

IWA06-KS30, IWA08-KS30, IWA10_KS30, IWA12-KS30 [Energy Star]

www.impecca.com

v1.3

Read the following notices and information carefully to ensure proper operation of your air

conditioner unit.

This manual is solely provided for informational purposes and in no way constitutes a legally

binding document between the manufacturer, distributor, and end consumer. Exact appear-

ance of your unit may dier from the pictures and diagrams enclosed.

Lea las siguientes indicaciones cuidadosamente para asegurar el correcto funcionamiento

de su unidad de aire acondicionado.

Este manual se proporciona únicamente con fines informativos y de ninguna manera

constituye un documento jurídicamente vinculante entre el fabricante, distribuidor y

consumidor final. Apariencia exacta de su unidad puede diferir de las imágenes y esque-

mas adjuntos.

WARNING:

To avoid permanent damage to unit:

Ensure it is in the upright position for a MINIMUM of 6

hours and a RECOMMENDED time of 24 hours before pow-

ering on the first time.

ADVERTENCIA:

Para evitar daños permanentes a la

unidad:

Asegúrese de que está en la posición vertical durante

un mínimo de 6 horas y un tiempo recomendado de 24

horas antes de encender la primera vez.

Spanish version of this manual available for download on

www.impecca.com

ENGLISH

–iii–

TABLE OF CONTENTS

Introduction ..............................................................................................................................6

Getting To Know Your Air Conditioner ..................................................................................7

Using Your Air Conditioner .....................................................................................................7

Delay Start/Stop (Timer) ...................................................................................................... 11

Installation Instructions ....................................................................................................... 14

R1 Insulation Installation (for some models)................................................................... 16

Cleaning & Maintenance ...................................................................................................... 18

Troubleshooting .................................................................................................................... 19

Electrical Information ........................................................................................................... 21

Customer Support ................................................................................................................. 21

One-Year Limited Appliance Warranty (US) ...................................................................... 22

Garantía Limitada Por Un Año (US) ................................................................................... 23

Garantie Limitée D’un An (US) ............................................................................................ 24

ENGLISH

–4–

 Plug in power plug completely.

 Do not start or stop the unit by inserting or

pulling out the power plug.

 Do not damage power cord or replace

with a non-original power cord.

• Otherwise, it may cause electric shock or

fire due to potential short circuit.

• It may cause electric shock or fire.

• If the power cord is damaged, it must

be replaced by the manufacturer or an

authorized service center or a similarly

qualified person to avoid hazard.

 Do not modify power cord length.

 Do not operate with wet hands or in a

damp environment.

 Do not direct airflow directly at room

occupants.

• It may cause electric shock or fire. • It may cause electric shock. • This could be harmful to their health.

 Always ensure eective grounding/

earthing.

 Do not allow water into or onto the front of

cabinet, control panel or power cord.

 Always use dedicated power outlet and

circuit breaker.

• Incorrect or missing grounding may lead to

electric shock.

• It may cause failure of unit or electric shock. • Sharing a circuit can lead to fire.

 Unplug the unit if it emits strange sounds,

smells or smoke.

 Do not plug unit into an electrical socket

that is loose or damaged.

 Do not operate the unit while the

chassis is open or removed.

• Unit may need repair. • It may cause fire and electric shock. • It may cause electric shock.

 Ensure the power cord is kept away from

any heating sources.

 Do not disassemble or modify unit.

 Do not use the power cord near

flammable gas or combustibles, such as

gasoline, benzene, paint thinner, etc.

• It may cause fire and electric shock. • It may cause failure and electric shock. • It may cause an explosion or fire.

 Ventilate room before operating

air conditioner if there was a gas leakage.

• It may cause explosion, fire, and burns.

WARNING

READ THESE NOTICES CAREFULLY—THEY ARE IMPORTANT!

 When the air filter is removed for cleaning,

avoid touching the internal metal parts of

the unit.

 Do not clean the air conditioner with water.

 Ventilate the room well when used

together with a stove, etc.

• It may cause an personal injury and/or

damage to the unit.

• Water may enter the unit and degrade the

insulation. It may cause an electric shock.

• An oxygen shortage may occur when

using a stove in a room with closed

windows.

 When the unit is to be cleaned, power o

the unit and circuit breaker.

 Do not put a pet or house plant where it

will be exposed to direct air flow.

 Do not use for specialized purposes.

• Do not clean unit when power is on as it

may cause fire and electric shock and/or

personal injury.

• This could injure or be harmful

to your pet or plants.

• Do not use this air conditioner to

preserve precision devices, food, pets,

plants, and art objects.

• It may cause deterioration, etc.

CAUTION

ENGLISH

–5–

CAUTION

ELECTRICAL SAFETY

• Be sure your electrical wiring is adequate for the model you have chosen. This information can be found on

the rating label, a silver-colored sticker generally located on the right side of the cabinet.

• Be sure the air conditioner is properly grounded. To minimize shock and fire hazards, proper grounding is

important. The power cord is equipped with a three-prong

grounding plug for protection against shock hazards.

• Your air conditioner must be connected to a properly ground-

ed wall receptacle. If the wall receptacle you intend to use

is not adequately grounded or protected by a time delay

fuse or circuit breaker, have a qualified electrician install the proper

receptacle.

• Ensure the receptacle is accessible aer the unit installation.

 Stop operation and remove unit from

window in severe storm or hurricane.

 Hold the plug by the head of the power

plug when unplugging unit.

 Unplug the power cord when not using

the unit for extended periods of time.

• Operation during a severe storm may allow

a significant amount of water to enter the

indoors.

• Pulling from the wire can cause wire to fray

leading to electric shock or fire.

• Will prevent damage to the unit.

 Do not place obstacles around air-intake

vents or inside cool air outlet.

 If unit is equipped with an outdoor

installation bracket, periodically ensure that

it has not become damaged.

 Always insert the filters securely.

Clean filter at least once per month.

• It may cause failure of appliance.

• If bracket is damaged, the unit can fall and

cause damage, personal injury or death.

• Operation with dirty filters (or without

filters) will eect performance and may

cause damage to the unit.

 Do not use strong detergent such as

wax or paint thinner to clean the unit.

Use a damp, so cloth.

 Do not place heavy objects on the

power cord and ensure that the cord

is not pinched or stressed.

 Do not place this window-type air

conditioner through a wall.

• Appearance may deteriorate due to change

of product color or scratching of its surface.

• There is danger of fire or electric shock.

• This will block the side vents and pre-

vent the unit from cooling properly.

CAUTION

NOTE: The power supply cord with this air conditioner

contains a current detection device designed to reduce the risk

of fire. In the event that the power supply cord is damaged, it

cannot be repaired -- it must be replaced with a cord from the

Product Manufacturer.

The power supply cord contains a current device that senses damage

to the power cord and excess current draw from the unit. To test your

current device do the following:

1. Plug in the Air Conditioner.

2. Press the TEST button. You will hear a click as the RESET button

pops out within the rubber housing and the LED will turn o.

3. Press the RESET button. You will hear a click as the button

engages and the LED will illuminate.

4. The power supply cord is now supplying electricity to the unit.

Note: Your model may have the TEST and RESET buttons on the

side or the front of the plug head.

NOTES:

• Do not use the TEST and RESET buttons to turn the unit on or o.

• If the current device fails the test or the power cord becomes dam-

aged, the entire power cord must be replaced with an equivalent

power cord and current device by a licensed electrician.

Side button

version

ENGLISH

–6–

INTRODUCTION

Thank you for purchasing this quality Impecca window air conditioner unit. To ensure

the longest life and highest energy eiciency of your unit, please carefully follow these

operating instructions. Keep these instructions in a safe place and consult them as

needed. Please note that constant enhancement and improvements to our air condi-

tioning units may mean that your model will slightly dier in appearance from the mod-

el pictured in this manual, but the actual operation and installation of the unit remains

unchanged. This manual is solely provided for informational purposes and does not

constitute a binding, legal contract.

SAFETY NOTICE:

This appliance should not be used by children or mentally/physically disabled persons with-

out strict, direct supervision by a responsible adult. Never play with or around the appliance.

SAFETY INFORMATION

• Before operation, ensure your electrical installation (outlets and circuits) complies

with the power specifications found on the unit.

• Before cleaning or maintaining the air conditioner, please turn o air conditioner and

unplug the unit.

• Make sure the power cord isn’t kinked, bent, or under the weight of sharp or heavy

objects.

• Do not pull or yank the power cord to unplug the unit or move the air conditioner.

• Do not insert or unplug the power plug with wet hands.

• Only use a grounded power outlet. Make sure the grounding is functional.

• If the power cord is damaged, it must be replaced by the manufacturer or a qualified

technician in order to avoid fire and electrical hazards.

• Should abnormal operation occur (such as a burning smell), please disconnect pow-

er cord immediately and contact your local dealer.

• If nobody is present to monitor the operation of the unit, please turn it o and dis-

connect the power cord.

• Do not splash or pour water on air conditioner to avoid causing a short circuit or

damage to the unit.

• Do not put or hang dripping objects above the air conditioner.

• Ensure the ambient temperature remains well above freezing (32°F or 0°C) to avoid

cracking or damaging the unit.

• Keep heat sources away from the air conditioner.

• Ensure the unit is far away from fire, inflammable, or explosive objects.

• Never allow children or persons with reduced physical, sensory, or mental capabili-

ties to operate or play around the air conditioner without direct adult supervision.

• Never allow children to perform cleaning or other user-maintenance operations

without direct adult supervision.

• Never attempt to repair or disassemble the air conditioner by yourself.

• Never insert objects into the air conditioner.

ENGLISH

–7–

OPERATING CONDITIONS

• The air conditioner must be operated within the temperature range of 62°F to 95°F

(16°C to 35°C).

• A perimeter of 12′′(30cm) around the air conditioner should be free of all objects.

• Keep air inlet and air outlet clean and free of obstructing objects.

• During operation, close doors and windows to improve cooling eect.

• Please put the air conditioner at smooth and flat ground for operation to avoid noise

and vibration.

• Do not tilt or turn over the air conditioner. If there’s problem, please disconnect the

power supply immediately and contact your local dealer or technical support.

GETTING TO KNOW YOUR AIR CONDITIONER

1. Upper rail

2. Cool air outlet

3. Cool air direction-

al levers

4. Fresh air vent

control (some

models)

5. Filter cover grasps

6. Control Panel

7. Outside air intake

(Do not block

these vents!)

8. Warm air intake

USING YOUR AIR CONDITIONER

FRESH AIR VENT (SOME MODELS)

When cooling, always leave the vent closed (Fig A).

When operating the unit in fan only mode, you may also open the vent (Fig B.) Another

option is opening the vent and exhaust at the same time(Fig C), which is good for re-

moving odors from the room during fan mode.

Fig A.

Fig B. Fig C.

ENGLISH

–8–

OVERVIEW OF CONTROLS FUNCTIONS

Before you begin, thoroughly familiarize yourself with the control panels as shown below

and all its functions, then follow the symbol for the functions you desire. The unit can be

controlled by the unit control panel located on the front of the device or with the remote

controller.

1. Temperature/Timer Down

2. Timer (Delay start/stop)

3. Check Filter light reset

4. Clean Air/Ionization (On Some models)

5. Function selector (Auto-Cool-Dry-Fan)

6. Energy Saver

7. Temperature/Timer Up

8. Display (Temperature/Timer)

9. Sleep mode

10. Fan Speed selector

11. Infrared Remote senor window

12. On/O

13. PMTS (On Some Models)

Note that your model's control panel may dier

slightly.

POWER ON/OFF

Press the On/O button to turn the unit on or o.

CLEAN AIR (ION) FEATURE (ON SOME

MODELS)

Available on certain models, the ion generator

creates an energized field and will help to re-

move pollen and impurities from the air, trap-

ping them in the filter.

Ion

PMTS

Control Panel

Ion



ENGLISH

–9–





TEMPERATURE ADJUSTMENT

Press or hold either Down  or Up  button until the de-

sired temperature is seen on the display. This tempera-

ture will be automatically maintained anywhere between

62° F (17° C) and 86° F (30° C).

If you want the display to read the actual room tempera-

ture, refer to the note: “To Operate on Fan Only”.

FAN SPEED ADJUSTMENT

Select the Fan Speed in four steps: Auto, Low, Med or

High. Each time the button is pressed, the fan speed

mode is shied. On Dry mode, the fan speed is controlled

at Low automatically.

OPERATING MODE (FUNCTION) SELECTION

To choose operating mode, press the Mode button.

Each time you press the button, a mode is selected in a

sequence that goes from AUTO, COOL, DRY, and FAN. The

indicator light beside will be illuminated and will remain

on once the mode is selected.

USING AUTO FEATURE

When you set the air conditioner in AUTO mode, it will

automatically select cooling or fan only operation de-

pending on the current room temperature and the target

temperature you have set. The air conditioner will con-

trol room temperature automatically. In this mode, the

fan speed cannot be adjusted.

USING DRY MODE

In this mode, the air conditioner will generally operate in

the form of a dehumidifier. Since the conditioned space is a

closed or sealed area, some degree of cooling will continue.

FAN ONLY MODE

Use this function only when cooling is not desired, such

as for room air circulation or to exhaust stale air (on some

models). Remember to open the vent during this function,

but keep it closed during cooling for maximum cooling

eiciency. You can choose any fan speed you prefer.

During this function, the display will show the actual room

temperature, not the set temperature as in the cooling

mode. In Fan Only mode, the temperature is not adjusted.

Ion



Ion



ENGLISH

–10–

PMTS — FOLLOW ME (SOME MODELS)

Some models are equipped with a special feature that allows

the remote control to act as a thermostat. If your unit shows

this PMTS LED on the control panel, and you have the accom-

panying LCD remote control then your unit is equipped.

You must activate this feature through the remote control by

pressing the PMTS button. Once activated, it is important to

keep the remote aimed at the air conditioner and place it in

the center of the room for best results.

ENERGY SAVER MODE

This function is available on COOL mode. The fan will con-

tinue to run for 3 minutes aer the compressor shuts o.

The fan then cycles on for 2 minutes at 10-minute intervals

until the room temperature is above the set temperature,

at which time the compressor turns back on and Cooling

Starts. Note that due to modern energy saving regulations,

this mode is on by default and you must turn it o if you

want the fan to run constantly during cooling mode.

SLEEP MODE

In this mode the selected temperature will increase by 2°F

(or 2°C) 30 minutes aer the mode is selected. The tempera-

ture will then increase by another 2°F (or 2°C) aer an addi-

tional 30 minutes. This new temperature will be maintained

for 6 hours before it returns to the originally selected tem-

perature. This ends the Sleep mode and the unit will contin-

ue to operate as originally programmed. The Sleep mode

program can be canceled at any time during operation by

pressing the Sleep button again.

CHECK FILTER

This feature is a reminder to clean the Air Filter for more

eicient operation. The LED (light) will illuminate aer 250

hours of operation. To reset aer cleaning the filter, press

the Check Filter button and the light will go o. See section

under Cleaning and Maintenance for how to clean the filter.

Note: Your filter may need to be cleaned much more oen

in especially dusty environments and may not need to be

cleaned as oen in especially clean environments. The 250

hour indicator is just there as a reminder.

Ion



PMTS

ENGLISH

–11–

DELAY START/STOP (TIMER)

The timer buttons enable two separate functions: one to

automatically start the unit within a 24 hour period of time

and another to automatically turn o the unit within a 24 hour

period of time. These functions are called, respectively, AUTO

ON and AUTO OFF.

AUTO ON INSTRUCTIONS:

1. Press the TIMER button twice, or until the TIMER ON

LED on the air conditioner's control panel should illumi-

nate. The air conditioner's display shows the last Auto-On

setting (if any). Now you are ready to reset the Auto-On time

to START the operation.

2. Press either the  or  buttons to set desired

Auto-On time. Each time you press the  button, the time will increase in 30 minute

increments, up to 10 hours, then in 1 hour increments up to 24 hours.

3. Aer setting the TIMER ON, there will be a one-half second delay before the remote

controller transmits the signal to the air conditioner. Then, aer approximately

another 2 seconds, the time setting will disappear from the unit's display and the

set temperature will re-appear on the display window. The Timer ON LED should

remain illuminated.

AUTO OFF INSTRUCTIONS:

1. Press the TIMER button once, or until the TIMER OFF LED on the air condition-

er's control panel should illuminate. The air conditioner's display shows the last

Auto-O setting (if any). Now you are ready to reset the Auto-O time to START the

operation.

2. Press either the  or  buttons to set desired Auto-O time. Each time you press

the  button, the time will increase in 30 minute increments, up to 10 hours, then in

1 hour increments up to 24 hours.

3. Aer setting the TIMER ON, there will be a one-half second delay before the remote

controller transmits the signal to the air conditioner. Then, aer approximately

another 2 seconds, the time setting will disappear from the unit's display and the

set temperature will re-appear on the display window. The Timer OFF LED should

remain illuminated.

Notes: It is possible to set both and Auto-On and Auto-O program at the same time. All times that are set are

the time from the moment of setting. So if you were to set a delay of 5 hours to turn on and immediately aer

set a delay of 6 hours to turn o, then the unit will operate for a total of 1 hour in 5 hours time from now.

All programs are erased aer their time elapses, so they will not repeat again the next day until reprogrammed.

Important: If you use a separate timer to obtain more control (such as turning on and o at a specific time every

day), the unit will remember its previous mode. It may, however, return to energy saver mode by default. If you do

use a timer, be sure that it is a heavy -duty grounded (three-prong) timer that is rated for the appropriate amper-

age.

 



ENGLISH

–12–

1 2

8 11

Phillips Screwdriver

Level

Scissors Pencil Tape Measure

PRE-INSTALLATION INSTRUCTIONS

REQUIRED TOOLS (NOT INCLUDED)

INCLUDED PARTS & ACCESSORIES*

1. Air conditioning unit

2. Flexible window filler panels

3. Upper Rail (may already be attached)

4. Upper Rail seal (may already be at-

tached to bottom of rail)

5. Foam sash seal (no adhesive)

6. Foam seal (with adhesive)

7. Upper Rail Screws (x4)

8. Screws (x6)

9. Frame lock

10. Window security bracket

11. User’s manual and Remote Manual

*Note: The parts and appearance of parts

included with your unit may vary.

ENGLISH

–13–

WINDOW REQUIREMENTS

Your air conditioner is designed

to install in a standard double

hung windows with opening

widths of 23 to 36 inches

(584mm to 914mm).

*For 6000 and 8000 BTU models,

you need a height of 14 inches

(356mm). For 10,000 and 12,000

BTU models, you need a height

of 15½ inches (394mm).

STORM WINDOW MODIFICATIONS

If you have storm windows, the exterior window frame will be slightly higher than the

windowsill, which results in an air conditioning unit that is slanted inward and may

cause water condensation to enter the room interior. Perform these modifications to

ensure proper operation of your unit. If you have a standard window, skip this step:

1. Cut a 2” thick piece of wood to the length of the interior window width.

2. Verify that the wood is level with or up to 0.5” (1cm) higher than the exterior

storm-window frame.

3. Fasten the wood with screws to the windowsill and proceed with mounting.

Wooden Windows

INTERIOR

WALL

INNER

WINDOW SILL

EXTERIOR

WALL

OFFSET

”

Exterior Wall

Board thickness

should be as required

for proper pitch and

run along the entire

window sill. Fasten

with nails or screws.

Storm Window

or other obstruction

1½” min

(38 mm)

ENGLISH

–14–

INSTALLATION INSTRUCTIONS

 Use caution when unpacking and installing. Sharp edges can cause injury.

Appearance of unit in these diagrams is for illustrative purposes only and may not precisely

reflect your unit’s design.

STEP 1: INSTALLING THE UPPER RAIL (IF NOT ALREADY ATTACHED)

1. Your upper rail may have come with the upper rail seal already aixed to the bottom

of the rail. If it is packaged separately, peel the backing o and aix it to the bottom

of the rail ensuring that the holes in the seal match up with the screw holes in the

rail. (Fig. A)

2. Use the 4 screws (included) to attach the upper rail to the pre-drilled holes on the

top of the cabinet as shown in Figure B. Ensure that the higher part of the rail is

facing the front of the air conditioning unit.

(Fig. B)

Note: Be sure to use all four screws when attaching

the top rail.

STEP 2: MOUNTING THE FLEXIBLE FILLER PANELS

1. Note the “Le” and “Right” markings on the panels.

2. Extend the flexible part of the filler panel past the filler panel’s frame

3. Slide the T-section into the side guide rails on the le and right of the unit.

4. Gently insert the upper and lower ends of the panel frame into the upper and lower

rail channels on the air conditioning unit.

T-section

Upper Rail

Lower Rail

Fig.B

Upper Rail seal

Upper Rail

Fig. A

ENGLISH

–15–

STEP 3: FOAM SEAL ON WINDOW FRAME

• Aix the foam seal (with adhesive G ) to the bottom of

the window sash.

STEP 4: MOUNT THE UNIT IN THE WINDOW

FRAME

1. With the help of another person, center the unit on the

windowsill. The lower rail should be completely flush

with the windowsill. Gently lower the window until it

holds the upper rail in place. The chassis and frames are

configured to allow for a natural pitch towards the outside of about 3-5°.

2. Extend the window fillers to the right and le edge of the window.

3. Fasten the upper rail and top corners of the window filler panels to the window

frame with screws. Use the frame locks to attach the bottom corners to the window-

sill.

ENGLISH

–16–

STEP 5: SECURING THE WINDOW

• To keep the window from

being unintentionally opened

and risk damaging the unit or

injuring passersby, use one

type C screw to fasten the se-

curity bracket to the window.

If your window frame is plastic

(PVC), fasten the bracket to the

side of the window frame (De-

tail 1)If your window is made

of wood, fasten the bracket into the closed upper window sash (Detail 2).

STEP 6: INSULATING FOAM SASH SEAL

• Prevent warm or cold

air from entering in

between the partially

opened window and

the closed upper

window by placing the

non-adhesive foam

sash seal in between

the window sash and

the glass pane.

R1 INSULATION INSTALLATION (FOR SOME MODELS)

"R1" is the name given to special additional insulation that applies to Energy Star certi-

fied models manufactured aer a certain cut-o date. If your model fits this criterion,

you will have found a weather stripping foam and additional panels that fit over the

side curtains among the parts

included with your air condi-

tioner.

WEATHER STRIPPING

In order to minimize air

leaks between the room air

conditioner and the window

opening, trim the weath-

er stripping with a proper

length, peel o the protective

backing and plug any gaps if

needed.

ENGLISH

–17–

R1 SIDE CURTAIN COVER INSTALLATION (SOME MODELS)

1. Aer the unit is installed in the window, measure the width of each side's exposed

filler panel as shown in the diagram.

2. Cut the insulation panel to size for each side of the side curtain.

3. Slide the R1 panel into place

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

1 2 3

4 5

Measure the inner width

of the side curtain

ENGLISH

–18–

CLEANING & MAINTENANCE

SAFETY WARNING

To avoid electric shock, fire, damage, or injury while performing maintenance on your

unit:

• Always turn o and disconnect the air conditioner from electric power.

• Never submerge the unit in water or spray liquids directly on the unit.

• Never use solvents or other flammable or volatile liquids (examples: paint thinner,

acetone, gasoline, etc.) to clean the air conditioner.

PRE-COOLING SEASON UNIT CHECK

Before using your air conditioner in the warm summer months, always perform the

following verifications to ensure reliable, eicient operation:

• Check the air inlets and outlets for any foreign objects (example: leaves, sticks, small

toys, etc.)

• Check that the electrical cord and socket are not damaged, bent, or fraying.

• Check the filter and clean if necessary.

POST-COOLING SEASON UNIT CHECK

Aer using your air conditioner in the warm summer months, always perform the fol-

lowing verifications:

• Disconnect the unit electrical power.

• Clean the filter and unit casing.

• Remove dust and other objects on the unit.

• Discard any accumulated water inside the unit (see section about drainage).

LONG-TERM STORAGE

Should you place your unit in long-term storage, perform all of the post-season checks

listed above and perform the following additional steps:

• Wrap the electrical cord loosely around the unit.

• Cover the unit with a sheet or cloth to prevent dust buildup inside during storage.

• WARNING: Never store the unit up-side down or on its side. This can permanently

damage the compressor.

DISPOSAL INFORMATION

• Most unit packaging materials are recyclable. Please dispose of them according to

local recycling guidelines.

• If you wish to discard the unit, contact your local authorities for specific appliance

disposal instructions. If the unit is functional and in good repair, but you wish to dis-

pose of it, consider donating it to a local charity.

ENGLISH

–19–

CLEANING THE OUTER HOUSING AND INTAKE GRILLE

If dust has accumulated on the unit, use a so, dry dusting cloth to wipe it o. If grease

or other harder to remove substances is on the unit, use a wrung-out cloth dampened

with warm, soapy water. Use a so brush to clean o the grille.

CLEANING THE FILTER

For energy eicient operation, your filter should be cleaned at least once a month. Units

in dusty environments may require more frequent filter cleaning.

• The filter removal handles are located on both sides of the unit (see "Getting to know

your air conditioner" diagram, number F

above).

• Remove it by sliding it out.

• Use a vacuum cleaner or rinse the filter in

cold water. If the filter is particularly dirty

(such as grease buildup), wash and gently

scrub the filter in a bath of warm (not hot)

soapy water. Let the filter completely dry

in a shady place; exposing the filter to

direct sunlight can cause deformation.

• Aer the filter is clean and completely dry, re-insert the filter.

Note: To avoid deformation and fire risk, never dry the filter with a heat source, such as a

hair dryer, fireplace, or heater.

TROUBLESHOOTING

PROBLEM / POSSIBLE CAUSES

THE AIR CONDITIONER DOES NOT FUNCTION AT ALL

• Is the power cable properly inserted into a functioning, grounded outlet?

• Is there a power failure such as a blown fuse or tripped circuit breaker?

• Is the ambient temperature lower than 61°F (16°C)? A safety device prevents the unit

from cooling the room to even lower temperatures.

INSUFFICIENT COOLING

• Is the unit temperature set properly?

• Is the air filter dirty?

• Are doors or windows open?

• Is the room directly exposed to sunlight or are there other heat sources in the room?

• Are there a large number of people in the room?

ENGLISH

–20–

WATER BUILD-UP IN THE UNIT, SPLASHING NOISE

• This is not a problem. This self-evaporative unit is designed allow condensate to

build up in the rear of the unit during cooling and dry modes. The rear fan then runs

through the pool of water, splashing it upon the evaporator coils, helping to cool

them down. This makes the unit more eicient and eliminates the need to hook up a

drain hose.

THE AIR CONDITIONER UNIT STARTS AND STOPS VERY FREQUENTLY.

• Verify the rating of your electrical system and outlets. You may need a qualified elec-

trician to troubleshoot and upgrade your electrical circuits if your air conditioner unit

exceeds the rated capacity.

FOG BLOWS OUT DURING COOLING

• In warm, high humidity environments this may naturally occur. Continued cooling

will remove excess humidity from the room and the fog will disappear.

THE UNIT EMITS A STRANGE SMELL

• This may be caused by residue from cooking and cigarette smoke, etc. that remain in

the air conditioning unit. Eliminated the source of the smell and clean the filter.

THE UNIT MAKES LOUD OR UNUSUAL NOISES AND VIBRATIONS

• Ensure that the unit is installed according to the installation instructions above.

THERE IS A “SQUEALING” NOISE

• The cycling of the refrigerant inside the unit can temporarily cause this noise.

THERE IS A “PATTING” NOISE

• This is oen caused by heat expansion in the plastic parts.

CONDENSATION FORMS AT THE COOL AIR OUTLET

• High humidity environments may cause condensation at the air flow output. Wipe

the condensation o with a sponge or dry cloth.

IF ANY OF THE FOLLOWING PHENOMENA OCCUR DESPITE THE ABOVE TROU-

BLESHOOTING TECHNIQUES, PLEASE TURN OFF THE UNIT AND DISCONNECT

THE POWER CORD IMMEDIATELY AND CONTACT TECHNICAL SUPPORT OR A

QUALIFIED TECHNICIAN:

• The fuse blows or circuit breaker trips frequently.

• The power cable is abnormally hot.

• The insulation of the power cable is ripped, shred or torn.

• The unit controls do not work.

• The unit produces abnormal noises.

La page charge ...

Impecca IWA25-KS30 Mode d'emploi

Marque: Impecca

Modèle: IWA25-KS30

Catégorie: Climatiseurs mobiles

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Impecca IWA25-KS30 User guide

Impecca IWA25-KS30 Mode d'emploi

Impecca IWA25-KS30 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents