USER MANUAL
210914A2
TABLE OF CONTENT
01 INSIDE THE BOX, PARTS DIAGRAM
02 INSTALLATION
03 OPTIONAL ACCESSORIES, MAINTENANCE,
TROUBLESHOOTING GUIDE, SPECIFICATIONS
04 SAFETY INSTRUCTIONS, INSTRUCTIONS DE SECURITE
05 FCC STATEMENT
1
2
3
5
4
Power Cord
Intensity Tuning Knob
Screw Hook
Hanging Ring
Hanging Bracket
Color Tuning Knob
K-Link Ports
Venting Holes
Reflector-55
A
B
C
D
E
F
G
H
I
INSIDE THE BOX
A500X
(Plug type varies from
country to country)
AC Adapter Cable Power Adapter Hanging Ring Hanging Bracket x 2 Screw Hook x 2
Reflector-55 Kessil Sticker Warranty Card
PARTS DIAGRAM
A
G
H
ED FCB
I
1
Controlling Multiple A500X
Mounting
Reflector-55
Control
• Turn the Intensity Tuning Knob (B) to adjust the bright-
ness of the fixture.
• Turn the Color Tuning Knob (F) to adjust the light to the
desired color.
• A500X can be connected and controlled through Kessil
Spectral Controller X with a K-Link Cable, or through
the WiFi Dongle with iPhone or Android phone app.
• Connect two or more lights with K-Link Cables as
shown in the image.
• Multiple A500X lights can be controlled by either
manually, an external controller, or the WiFi Dongle.
• When controlling without an external controller or WiFi
Dongle, tuning controls on any light control all other
lights in chain.
• Screw the Hanging Ring (D) into the center screw hole.
• Hang the light with the two Screw Hooks (C) and the
two Hanging Brackets (E).
• To install the Hanging Brackets (E), remove the screws
on the A500X, use the same screws to secure the
fasteners with triangular rings onto the light fixture.
Power Cord
(9.2ft / 2.8m)
Power Adapter
Adapter Cable (5.9ft / 1.8m)
(Plug type varies from country to country)
(Controller X not included) (WiFi Dongle not included)
INSTALLATION
Step 1Power
Step 2
Step 3
Step 4
Step 5
Connect the A500X to the power adapter and plug it into
a wall outlet. Turn the Intensity Tuning Knob (B) to the
right to turn on the light.
The complementary Reflector-55 narrows the beam of
the light to increase the light intensity and penetration,
and to avoid overspilling.
2
CAUTION
HOT SURFACE. DO NOT TOUCH
WHEN LIGHT IS ON & WITH
REFLECTOR ACCESSORIES
Push the K-Link Cable connector or WiFi Dongle down to
make sure the connection is firm.
MAINTENANCE
OPTIONAL ACCESSORIES
1. Keep the fan and Venting Holes (H) clear of dust. To clean the fan, unplug the unit and insert the tip of a
CO2 dust blower (or similar dust blower) in one of the venting holes for the Fan. Hold and spray. You can
also gently vacuum out the dusts through the venting holes.
2. Keep the LED array and Reector-55 (I) clean. If the array lens and reector become contaminated with
water, dust, or other particles, unplug the unit and clean them with isopropyl alcohol. Wet a cotton swab or
a napkin in isopropyl alcohol, gently wipe the surface, and let it dry.
3. Keep plastic covers for K-Link Ports (G) plugged in when the ports are not in use.
Keep the ports clean all-time.
Dimensions
Weight
Ø5.23” x 3.68” (Ø13.3 cm x 9.36 cm)
1.72 Ibs (0.78 kg)
llluminator Power Adapter
Power Consumption 185W maximum Input 100-240V~ AC 50-60 Hz
Input Voltage 48V DC 5% Output 48V DC, maximum 4.2A
+
_
SPECIFICATIONS
TROUBLESHOOTING GUIDE
Problem
Make sure the fan is operating properly.
Cause / Solution
Please make sure to perform maintenance before doing any troubeshooting.
Light doesn’t turn ON
Unit is flickering
Make sure the unit is connected to the power adapter and the power adapter is plugged
into an outlet with the correct specifications.
Make sure the device is operating within the specified operating temperature range.
If unit overheats, it will automatically shut down.
Make sure the unit has not overheated by operating at a room temperature above
100°F/40°C.
Make sure the power adapter has the right specifications.
Make sure the power adapter has the right specifications.
Make sure electrical power is available to the AC outlet being used.
3
Unit Dimensions and Weight
1. Attention: Une mauvaise utilisation de cet appareil contrairement à ces instructions peut
entraîner des blessures ou endommager le produit.
2. N'UTILISEZ PAS d'adaptateur secteur en dehors des spécifications. Il s'agit d'un risque
d'incendie et peut entraîner une panne de l'unité.
3. NE PAS utiliser à l'extérieur. Cet appareil est destiné à une utilisation en intérieur uniquement.
4. N'exposez PAS l'appareil à un environnement extrêmement humide et ne l'immergez pas dans
l'eau. Cela peut entraîner une panne de l'unité.
5. NE placez PAS l'illuminateur de travail en contact étroit avec des objets. Cela peut provoquer
une surchauffe des objets et une surchauffe de l'appareil.
6. Gardez la matrices LED loin des objets pointus. Des objets tranchants peuvent briser la lentille
du réseau et entraîner une défaillance de l'unité.
7. NE PAS couvrir ni placer d'objets sur l'adaptateur secteur. L'adaptateur secteur ne doit pas être
contenu dans un espace hermétique.
8. NE PAS bloquer ou couvrir le ventilateur (entrée d'air) (H). Cela peut entraîner une surchauffe
de l'appareil et entraîner une panne.
9. ASSUREZ-VOUS que la lumière est correcte et solidement montée.
INSTRUCTIONS DE SECURITE
SAFETY INSTRUCTIONS
1. Caution: Misuse of this device contrary to these instructions may result in physical injury or
damage to the product.
2. DO NOT use a power adapter outside of the specifications. This is a fire hazard and may lead
to unit failure.
3. DO NOT use outdoors. This unit is intended for indoor use only.
4. DO NOT expose unit to an extremely humid environment or submerse unit in water. This may
lead to unit failure.
5. DO NOT place working illuminator in close contact with any objects. This may cause objects to
heat up and the unit to overheat.
6. KEEP LED array away from sharp objects. Sharp objects may break the array lens and lead to
unit failure.
7. DO NOT cover or place objects on the power adapter. Power adapter should not be contained
in an airtight space.
8. DO NOT block or cover the Venting Holes (H). This may cause the device to overheat and lead
to failure.
9. ENSURE that the light is correct and securely mounted.
4
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from thatto which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
• Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's
authority to operate this equipment.
• This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance of 8
inches (20cm) between the radiator & your body.
@kessilled
@kessil kessil.comkessil.led kessiltube
5
This is a LED light source emitting 40 % or more of total radiation power of the range 250-800 nm in the range of 400-480 nm, and
intended for coral growth.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
Kessil A500X Tuna Blue Manuel utilisateur
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
- English: Kessil A500X Tuna Blue User manual
Documents connexes
Autres documents
-
Vari-Lite VLZ WASH Manuel utilisateur
-
Zhone ZNID24xxA Le manuel du propriétaire
-
ETC Source 4WRD Installation and User Manual
-
-
-
Asus ROG Strix X570-I Gaming Manuel utilisateur
-
-
Asus ROG CROSSHAIR VIII FORMULA Manuel utilisateur
-
Samsung HW-NW700 Manuel utilisateur