ULTIMATE SPEED Car and Motorcycle Battery Charger Manuel utilisateur

Catégorie
Chargeurs de batterie
Taper
Manuel utilisateur
CAR & MOTORCYCLE
BATTERY CHARGER ULGD 5.0 C1
IAN 373295_2104
BATTERILADER TIL BIL
Oversættelse af den originale driftsvejledning
DK
KFZ-BATTERIELADEGERÄT
Originalbetriebsanleitung
DE AT CH
CHARGEUR DE BATTERIE POUR VOITURE
Traduction du mode d’emploi d‘origine
FR BE
VOERTUIG-ACCULADER
Vertaling van de originele bedieningshandleiding
NL BE
CAR & MOTORCYCLE BATTERY CHAR
GER
Translation of the original instructions
GB IE NI
NL BE
DK
GB IE NI
Before reading, unfold the page containing the illustrations
and familiarise yourself with all functions of the device.
DK
Før du læser, vend siden med billeder frem og bliv
bekendt med alle apparatets funktioner.
FR BE
Avant de lire le document, allez à la page avec les
illustrations et étudiez toutes les fonctions de l’appareil.
NL BE
Klap, voordat u begint te lezen, de pagina met
afbeeldingen uit en maak u aansluitend vertrouwd
met alle functies van dit apparaat.
DE AT CH
Klappen Sie vor dem Lesen die Seite mit den Abbildungen
aus und machen Sie sich anschließend
mit allen Funktionen des Gerätes vertraut.
GB / IE / NI Translation of the original instructions Page 5
DK Brugs- og sikkerhedsanvisninger Side 22
FR / BE Traduction du mode d’emploi d‘origine Page 39
NL / BE Vertaling van de originele bedieningshandleiding Pagina 58
DE / AT / CH Originalbedienungsanleitung Seite 76
A
891011
2 3 4 6 71
B
C
5
12
14
15
16
V7.5-10.5 10.5-12.8 14.1 14.4 14.4 12.8
A0.8 5.0 3.0 0.8 0.1 0.8
1 2 3 4 5 6 7
13
GB/IE/NI 5
zTable of pictograms used
Read the instruction
manual of this product
attentively and with care
before use.
220 -
240
V~
50Hz
Alternating voltage 220
– 240 V with a frequency
of 50 Hz
NOTE:
This symbol indicates
additional information
and explanations on the
product and its use.
Caution!
Possible risks!
Caution!
Explosion hazard!
Caution! Risk of electric
shock!
T3.15A
Internal fuse
Dispose of the batteries
in the specified battery
collection points.
IP65 Protected against jets of
water and dust-proof
Only for use in closed,
ventilated rooms!
Do not dispose of any
electrical devices in
domestic waste!
Packaging material –
corrugated paper
Dispose of packaging
properly. Do not dispose
of the appliance in house-
hold waste!
Table of pictograms used ............................................... Page 5
Introduction ..................................................................... Page 6
Intended use .................................................................... Page 6
Package contents .............................................................. Page 7
Equipment ....................................................................... Page 7
Technical specifications ..................................................... Page 8
Charging characteristics .................................................... Page 8
Safety instructions .......................................................... Page 8
Specific safety instructions ............................................. Page 14
Before use ........................................................................ Page 14
Using the device .............................................................. Page 15
Connection ...................................................................... Page 15
Disconnecting................................................................... Page 15
Standby / Measuring battery voltage .................................. Page 16
6 V batteries .................................................................... Page 16
12 V batteries .................................................................. Page 16
Revival ............................................................................ Page 16
Selecting programs ........................................................... Page 16
Maintenance and care .................................................... Page 18
Information about recycling and disposal .................... Page 18
EU Declaration of Conformity ........................................ Page 19
Warranty and service information ................................ Page 20
Warranty conditions.......................................................... Page 20
Warranty period and statutory claims for defects .................. Page 20
Extent of warranty ............................................................. Page 20
Processing of warranty claims ............................................ Page 20
6GB/IE/NI
Suitable for motorbikes
(Program 2) Suitable for cars
(Program 3)
Suitable for the charging
of 12-V batteries Suitable for the charging
of 6-V batteries
Direct current Made from recycled
material
6 V – Mode
(Program 1) Protection class II
Protect electrical connec-
tions from rain! Winter – AGM – Mode
(Program 4)
Do not smoke! Avoid flames and sparks!
Car and motorcycle battery charger ULGD 5.0 C1
zIntroduction
Congratulations! You have purchased one of our high- quality products.
Please familiarise yourself with the product before using it for the first
time. To do so, please read through the following operating and safety
instructions carefully.
KEEP OUT OF THE REACH OF CHILDREN!
zIntended use
The Ultimate Speed ULGD 5.0 C1 is a multi-level car and motorcycle bat-
tery charger, which is suitable for charging and trickle charging 6 V- (3
cells) or 12 V (6 cells) lead acid batteries with electrolyte solution (WET),
with electrolyte absorbing mats (AGM), with gel gel-type electrolyte (GEL)
or calcium batteries. The device is not suitable for charging lithium-ion
batteries!
You can also regenerate discharged batteries (depending on the battery
type). The car and motorcycle battery charger has a safety circuit against
sparking and overheating. Keep these instructions in a safe place. Ensure
you hand over all documentation when passing the product on to anyone
else. Any use that differs to the intended use as stated above is prohi-
bited and potentially dangerous. Damage or injury caused by misuse
or disregarding the above warning is not covered by the warranty or
any liability on the part of the manufacturer. The device is not intended
for commercial use and should only be used indoors. Commercial use
will void the guarantee. The product must only be started up initially by
people who have been trained to do so.
NOTE:
The car and motorcycle battery charger cannot charge any electrical
vehicles with integrated rechargeable battery.
GB/IE/NI 7
NOTE:
No jumpstart of 6V or 12 V batteries possible.
zPackage contents
1 Car and motorcycle battery charger
1 Operating instructions
zEquipment
To do this see Fig. A, B:
After unpacking the product, please check that all of the package con-
tents are present and that the battery charger is in perfect condition. Do
not use the device if it is defective.
1Car and motorcycle battery charger
2LED reverse polarity (red)
3Standby LED (green)
412 V / 0.8 A (Program 2)
5 12 V / 5.0 A (Program 3)
6 12 V / 5.0 A (Program 4)
7 6 V / 0.8 A (Program 1)
8Charging display
9Status display
10 Voltage display
11 Program selector button
12 Mains cable
13 Positive pole connection terminal (red)
14 Negative pole connection terminal (black)
15 Positive pole connection cable (red)
16 Negative pole connection cable (black)
NOTE:
The use of the term ‘product’ or device’ in the following text refers to the
car and motorcycle battery charger named in these operating instruc-
tions.
8GB/IE/NI
zTechnical specifications
Model: ULGD 5.0 C1
Rated voltage: 220-240 V~ 50 Hz
Rated intake current: 0,8 A
Rated output DC
voltage: 6 V / 12 V
Rated output direct current: 0,8 A / 5,0 A
Ambient temperature: -20 °C to 50 °C
Housing protection type: IP 65
Appliance class: II (dual insulation)
Battery types:
6 V lead acid battery,
1.2 Ah – 14 Ah
12 V lead acid battery,
1.2 Ah – 120 Ah
zCharging characteristics
To do this see Fig. C:
1Reverse polarity and diagnosis
2Recharge / desulphation
3Start of charging with a high current strength
4Charging up to 80%
5Absorption – charging up to 100%
6Trickle charging and monitoring
7Demand recharging
Changes to technical and visual aspects of the product may be made
as part of future developments without notice. Accordingly, no warranty
is offered for the physical dimensions, information and specifications in
these operating instructions. The operating instructions cannot therefore
be used as the basis for asserting a legal claim.
zSafety instructions
PLEASE READ THROUGH THE INST-
RUCTION MANUAL CAREFULLY
BEFORE USE. THESE FORM PART OF
GB/IE/NI 9
THE PRODUCT AND MUST BE AVAILABLE
AT ALL TIMES! KEEP OUT OF THE REACH
OF CHILDREN!
The charger is only suitable for indoor
operation!
DANGER!
Avoid danger to life and danger of injury
from improper use!
CAUTION!
Do not operate the device with a damaged
cable, mains cable or mains plug. Damaged
mains cables pose danger to life from electric
shock.
In case of damage, the mains cable must only
be repaired by authorized and trained specia-
lists! Contact the service point of your country
if you need any repair!
DANGER OF ELECTRIC SHOCK!
Ensure that the vehicle is not in operation
if the battery is installed firmly in the vehicle!
Switch off the ignition and put the vehicle into
the parking position, with the parking brake
engaged (e.g. car) or the rope attached
(e.g. boat)!
DANGER OF ELECTRIC SHOCK!
Disconnect the car and motorcycle
battery charger from the mains before remo-
ving the connection terminals.
Connect the connection terminal that is not
connected to the car body first.
Connect the other connection terminal to the
car body away from the battery and the gaso-
line line.
Connect the car and motorcycle battery char-
ger to the supply grid only after doing this.
Disconnect the car and motorcycle battery
charger from the supply grid after charging.
Only then disconnect the connection terminal
from the car body. Then disconnect the con-
nection terminal from the battery.
10 GB/IE/NI
DANGER OF ELECTRIC SHOCK!
Only touch the pole connection terminals
(„–“ and „+“) in the insulated area!
DANGER OF ELECTRIC SHOCK!
Conduct the connection to the battery
and the socket of the mains grid completely
protected from moisture!
DANGER OF ELECTRIC SHOCK!
Perform installation, servicing and main-
tenance of the car and motorcycle battery
charger only when the mains current is not
connected!
DANGER OF ELECTRIC SHOCK!
First disconnect the negative pole con-
nection cable (black) of the car and motorcyc-
le battery charger from the negative pole of
the battery upon completing the charging and
trickle charging process, if the battery is
continually connected in the vehicle.
Do not leave any toddlers or children unsuper-
vised around the car and motorcycle battery
charger!
Children cannot assess possible dangers in
use of electrical devices. Children must be su-
pervised to ensure that they do not play with
the device.
EXPLOSION HAZARD!
Protect yourself from highly explosive
oxyhydrogen reactions! Gaseous hydrogen
can escape during charging or maintenance
charging of the battery. Oxyhydrogen is a
potentially explosive mix of gaseous hydrogen
and oxygen. The oxyhydrogen reaction occurs
at contact with open fire (flames, smouldering
or sparks)! Perform charging and maintenan-
ce charging in a weather-protected space that
is ventilated well. Ensure that there are no
naked flames (flames, smouldering or sparks)
during charging or maintenance charging!
GB/IE/NI 11
EXPLOSION AND FIRE HAZARDS!
Ensure that explosive or flammable substan-
ces, such as gasoline or solvents cannot be
ignited when you are using the car and motor-
cycle battery charger!
EXPLOSIVE GASES!
Avoid flames and sparks!
Ensure sufficient ventilation when charging.
Put the battery onto a well-ventilated surface
when charging. Otherwise, the device can
be damaged.
EXPLOSION HAZARD!
Ensure that the positive pole connection
cable has no contact with a fuel line (e.g.
petrol line)!
DANGER OF CAUSTIC BURNS!
Protect your eyes and skin from caustic burns
from the acid (sulphuric acid) when it comes
into contact with the battery!
Use: acid-resistant safety goggles, clothing
and gloves! If your eyes or skin have come
into contract with the sulphuric acid, flush the
affected body region with plenty of clear, run-
ning water and seek medical advice at once!
Avoid electrical short circuits when connecting
the car and motorcycle battery charger to the
battery. Connect the minus pole connection
cable only to the minus pole of the battery or
the car body. Connect the plus pole connec-
tion cable only to the plus pole of the battery!
Before connecting to the mains, verify the
mains power has the required 230 V~ 50 Hz,
a 16A fuse and an ELCB switch (earth leaka-
ge circuit breaker)! Otherwise, the device can
be damaged.
Do not use the car and motorcycle battery
charger near any fires, heat and long-term
temperatures above 50°C! For higher
temperatures, the output power of the car
and motorcycle battery charger will drop au-
tomatically.
Only use the car and motorcycle battery char-
ger with the original parts it was
12 GB/IE/NI
delivered with!
Do not cover the car and motorcycle battery
charger with any objects! Otherwise, the de-
vice can be damaged.
Protect the electrical contact surfaces of the
battery from short circuit!
Only use the car and motorcycle battery char-
ger for the charging and maintenance char-
ging of undamaged 6V-/12V-lead batteries
(with electrolyte solution or gel)! Otherwise,
property damage may be the consequence.
Do not use the car and motorcycle battery
charger for the charging and maintenance
charging of non-rechargeable batteries. Ot-
herwise, property damage may be the conse-
quence.
Do not use the car and motorcycle battery
charger for the charging and maintenance
charging of damaged or frozen batteries! Ot-
herwise, property damage may be the conse-
quence.
Please refer to the original operating instruc-
tions about the maintenance of your battery
prior to connecting the car and motorcycle
battery charger! Otherwise, there is a danger
of injury and/or the risk of damage to the de-
vice.
Before connecting the car and motorcycle
battery charger to a battery that is continually
connected to the vehicle, learn about compli-
ance with the electrical safety and maintenan-
ce in the original operating instructions of the
vehicle! Otherwise, there is a danger of injury
and/or the risk of property damage.
Disconnect the car and motorcycle battery
charger from the mains current when it is not
is use to protect the environment as well!
Note that power is consumed in standby ope-
ration as well.
Always pay attention and be aware of what
you are doing. Proceed reasonably and do
not put the car and motorcycle battery char-
ger into operation when you are not focused
or not feeling well.
GB/IE/NI 13
Personal safety:
This device may be used by children aged
8years and older, and by persons with redu-
ced physical, sensory or mental capacities, or
a lack of experience and knowledge, if they
are supervised or have been instructed in how
to use the device safely and understand the
dangers that may arise when using it.
Do not allow children to play with the device.
Cleaning and day-to-day maintenance must
not be performed by children without super-
vision.
Children must be supervised to ensure that
they do not play with the device.
Keep the device away from people –
especially children – and household pets.
Within the working area, the user is responsi-
ble for any damage or injury to third parties
that was caused by the use of the device.
Do not leave the device charging unattended.
Keep the device in a dry location and out of
the reach of children.
This helps prevent device damage
and possible personal injuries that
could result from it:
Working with the device:
Before setup or first use, check the device for
any damage and do not use unless in perfect
working order.
Make sure that the mains plug and connection
terminals do not get wet. Do not expose the
device to rain or wet weather. Do not let the
device come into contact with water. Do not
immerse the device in water. There is a risk of
electric shock!
In hot weather, do not leave the device in a
car. This could permanently damage the de-
vice.
Do not operate the device near to flammable
liquids or gases. Failure to do so risks causing
a fire or explosion!
Switch the device off and remove the mains
14 GB/IE/NI
plug from the socket in the following cases:
When you are not using the device;
If you are leaving the device unsupervised;
If you are doing cleaning work;
If the connection cable is damaged;
Only use the accessories supplied and
recommended by the manufacturer.
Do not disassemble or modify the car and mo-
torcycle battery charger. This device must only
be repaired by a maintenance technician.
Do not use the device in areas with a risk of
explosion, e.g. near flammable liquids, gases
or powders.
Do not expose the device to any source of
heat.
CAUTION: How to avoid accidents
and injuries from electric shock:
Electrical safety:
Do not carry the device by the cable. Do not
unplug the plug from the socket by pulling on
the cable. Protect the cable from heat, oil and
sharp edges.
If the cable is damaged, unplug the plug im-
mediately from the socket.
zSpecific safety instructions
A slightly higher temperature during charging
is absolutely normal and not a malfunction.
Protect the car and motorcycle battery charger
1 from moisture and high temperatures, inclu-
ding fires.
Store the car and motorcycle battery charger
1 in a dry place and protect the device from
moisture and corrosion.
Do not drop the car and motorcycle battery
charger 1 while it is being used.
zBefore use
Take all parts from the packaging and check whether the device or
parts show any damage. If this is the case, do not use the device.
GB/IE/NI 15
Contact the manufacturer via the indicated service address. Remove
all protective films and other transport packaging. Check that the de-
livery is complete.
Always pull the mains plug from the socket before you perform any
work at the car and motorcycle battery charger 1.
Before connecting the charger please read the user instructions for
the battery.
In addition, you must adhere to the instructions from the vehicle ma-
nufacturer where a battery is continuously connected in the vehicle.
Secure the car or motorcycle, switch the ignition off.
Clean the battery poles. Make sure that the dirt does not come into
contact with your eyes.
Make sure that there is sufficient ventilation.
NOTE: The ambient temperature is measured in the charger. Hence, for
optimum function, make sure the battery exhibits the same temperature as
the environment.
zUsing the device
zConnection
NOTE:
Always observe the instructions from the vehicle manufacturer or the
battery manufacturer.
Disconnect the minus pole connection cable (black) of the vehicle
from the minus pole of the battery first before charging and mainte-
nance charging if the battery is continually connected in the vehicle.
The minus pole of your battery is usually connected to the car body
of the vehicle.
Then disconnect the plus pole connection cable (red) of the vehicle
from the plus pole of the battery.
Only then connect the „+“ pole quick-contact connection terminal
(red) 13 of the car and motorcycle battery charger to the „+“ pole of
the battery.
Connect the „–“ pole quick-contact connection terminal (black) 14 to
the „–“ pole of the battery. Connect the mains cable 12 of the car
and motorcycle battery charger 1to the socket.
If the output terminals are connected in reverse the red LED reverse
polarity 2lights up.
zDisconnecting
Disconnect the device from the mains current.
Disconnect the „–“ pole quick-contact connection terminal (black) 14
from the „–“ pole of the battery.
Disconnect the „+“-pole quick contact-connection terminal (red) 13
from the „+“-pole of the battery.
Reconnect the plus pole connection cable of the battery to the plus
pole of the battery.
Reconnect the minus pole connection cable of the battery to the mi-
nus pole of the battery.
16 GB/IE/NI
zStandby / Measuring battery voltage
After connecting the mains supply, the device is in standby mode. The
standby display 3lights up green. When the connection terminals are
connected, the battery voltage is displayed in the LC display (voltage
display 10 ). The segments of the status display 9are empty. If the
measured voltage is below 3.8 V or above 15V, then this means the
battery is not charging. The error message
„Err“ will be shown briefly in the display. The device switches to standby.
z6 V batteries
If a battery is measured in the voltage range 3.7 – 7.3 V, then you can
only select Program 1.
z12 V batteries
If a battery is identified as being in the critical voltage range from 7.3 –
10.5 V, then the device will check whether it is a fully-charged 6 V
battery or a discharged 12 V battery. Press the program selector button
11 to select a program. The device carries out a test measurement
procedure for approx. 90 seconds. The display will show:
If after approx. 90 seconds, the identified value is between 7.3 – 7.5 V,
then the 12 V battery is defective. The device switches to standby.
zRevival
If after approx. 90 seconds, the identified value is between 7.5 – 10.5 V,
then a 12 V battery is present. The charging process starts with pulse
operation for revival of the battery. The voltage display 10 flashes. Once
10.5 V is reached, the device switches to further charging levels.
The revival procedure is identical for all 12 V charging programs.
zSelecting programs
Note:
If a battery is identified in the voltage range of 3.7 – 7.3V, then
programs 2-3-4 cannot be selected. The charging process continues
automatically. Depending on the program selected, the charging charac-
teristics for voltage, time and temperature are monitored. With diagnosis
program, revival mode and trickle charging.
Program max. (V) max. (A)
17.3 V 0.8 A
GB/IE/NI 17
214.4 V 0.8 A
314.4 V 5.0 A
414.7 V 5.0 A
Program 1 , „6 V“, (7.3 V / 0.8 A)
To charge 6 V batteries with a capacity less than 14 Ah.
Press the program selector button 11 to select Program 1.
The symbol 7is shown in the LC display. During the charging
process, the charging display 8flashes and shows how far the charging
process has progressed (1 – 4bars). When the battery is fully charged,
the status display 9shows 4 bars. The flashing stops and the device
switches to trickle charging automatically.
Program 2 , „12 V“, (14.4 V / 0.8 A)
To charge 12 V batteries with a capacity less than 14 Ah.
Press the program selector button 11 to select Program 2. The symbol
4is shown in the LC display. During the charging process, the charging
display 8flashes and shows how far the charging process has progres-
sed (1 – 4 bars). When the battery is fully charged, the status display 9
shows 4 bars. The flashing stops and the device switches to trickle
charging automatically.
Program 3 , „12 V“, (14.4 V / 5.0 A)
To charge 12 V batteries with a capacity of 14 Ah – 120 Ah. Press the
program selector button 11 to select Program 3. The symbol 5is
shown in the LC display. During the charging process, the charging
display 8flashes and shows how far the charging process has progres-
sed (1 – 4 bars). When the battery is fully charged, the status display 9
shows 4 bars. The flashing stops and the device switches to trickle
charging automatically.
Program 4 , „12 V“, (14.7 V / 5.0 A)
To charge 12 V batteries with a capacity of 14 Ah – 120 Ah under cold
conditions or to charge AGM batteries. Press the program selector button
11 to select Program 4.
NOTE:
This program starts, with a slight time delay if necessary.
The symbol 6is shown in the LC display. During the charging
process, the charging display 8flashes and shows how far the charging
process has progressed (1 – 4 bars). When the battery is fully charged,
the status display 9shows 4 bars. The flashing stops and the device
switches to trickle charging automatically.
18 GB/IE/NI
Trickle charging
As described in „Selecting programs“, the device has an automatic trickle
charging procedure. Depending on the drop in voltage in the batte-
ry – through self-discharge – the charger reacts with different levels of
charging current. The battery can remain connected to the charger over a
longer period of time.
Device protection function
As soon as a different situation occurs, such as a short circuit, critical
drop in voltage during the charging process, open circuit or reversed
connection of the output terminals, the battery charger 1switches off
automatically. The electronic system resets the system immediately to its
home position, in order to avoid damage. If the device should become
too hot during charging, the output power is automatically reduced. This
protects the device from damage.
zMaintenance and care
Always pull the mains cable 12 from the socket before you perform
any work on the car and motorcycle battery charger 1.
The device is maintenance-free. Deactivate the device. Clean the me-
tal and plastic surfaces of the device with a dry cloth.
Never use any solvents or other aggressive cleaning agents.
zInformation about recycling and disposal
DO NOT DISPOSE OF ELECTRICAL TOOLS IN HOUSE-
HOLD WASTE!
Please return this device, accessories and packaging to your local
recycling depot. Do not dispose of the car and motorcycle battery
charger in household waste, in fire or in water. Devices that are
no longer functional should be recycled wherever possible. Ask your
local stockist for advice.
As the consumer you are legally obliged (by the German Battery
Ordinance) to return any and all used batteries. Batteries
containing harmful substances are labelled with the adjacent
symbol, which indicates the prohibition on disposal in household waste.
The abbreviations for the relevant heavy metals are: Cd = cadmium,
Hg = mercury, Pb = lead.
Take used batteries to a waste management company in your city or com-
munity or return them to your dealer. This satisfies your legal obligations
while also making an important contribution to protecting the environ-
ment.
Note the labelling on the packaging and separate the packaging
material components for disposal if necessary. The packaging
material is labelled with abbreviations (a) and numbers (b) with
the following meanings: 1–7: Plastics, 20–22: Paper and cardboard,
80–98: Composites.
GB/IE/NI 19
zEU Declaration of Conformity
We,
C. M. C. GmbH
Responsible for documentation:
Dr Christian Weyler
Katharina-Loth-Str. 15
66386 St. Ingbert
hereby take sole responsibility for declaring that the product
Car & motorcycle battery charger
Year of manufacture: 2022/04
IAN: 373295_2104
Model: ULGD 5.0 C1
Model number: 2406
meets the basic safety requirements as specified in the European Directi-
ves
Low Voltage Directive
2014/35/EU
Electromagnetic Compatibility
2014/30/EU
RoHS Directive
2011/65/EU + 2015/863/EU
and the amendments to these Directives.
The object of the declaration described above meets the requirements of
Directive 2011/65/EU of the European Parliament and of the Council of
8 June 2011 on the restriction of the use of certain hazardous substan-
ces in electrical and electronic equipment. This conformity assessment is
based on the following harmonised standards:
EN 60335-2-29:2004/A11:2018
EN 60335-1:2012/A2:2019
EN 62233:2008
EN 55014-1:2017
EN 55014-2:2015
EN 61000-3-2:2019
EN 61000-3-3:2013+A1:2019
St. Ingbert, 01.06.2021
On behalf of Dr Christian Weyler
– Quality Assurance –
20 GB/IE/NI
zWarranty and service information
Warranty from Creative Marketing & ConsultingGmbH
Dear Customer,
The warranty for this equipment is 3 years from the date of purchase. In
the event of product defects, you have legal rights against the retailer
of this product. Your statutory rights are not affected in any way by our
warranty conditions, which are described below.
zWarranty conditions
The warranty period begins on the date of purchase. Please retain the ori-
ginal sales receipt. This document is required as your proof of purchase.
Should this product show any defect in materials or manufacture within
3 years from the date of purchase, we will repair or replace it – at our
discretion – free of charge. This warranty service requires that you retain
proof of purchase (sales receipt) for the defective device for the three
year period and that you briefly explain in writing what the fault entails
and when it occurred. If the defect is covered by our warranty, we will
repair and return your product or send you a replacement. The original
warranty period is not extended when a device is repair or replaced.
zWarranty period and statutory claims for
defects
The warranty period is not extended by the guarantee. This also applies
to replaced and repaired parts. Any damages or defects detected at the
time of purchase must be reported immediately after unpacking. Any
incidental repairs after the warranty period are subject to a fee.
zExtent of warranty
This device has been manufactured according to strict quality guidelines
and carefully inspected before delivery. The warranty applies to material
and manufacturing defects only. This warranty does not extend to product
parts, which are subject to normal wear and tear and can thus be regar-
ded as consumable parts, or for damages to fragile parts, e.g. switches,
rechargeable batteries or parts made from glass. This warranty is voided
if the product becomes damaged or is improperly used or maintained.
For proper use of the product, all of the instructions given in the operating
instructions must be followed precisely. If the operating instructions advise
you or warn you against certain uses or actions, these must be avoided
in all circumstances. The product is for consumer use only and is not inten-
ded for commercial or trade use. The warranty becomes void in the event
of misuse and improper use, use of force, and any work on the device
that has not been carried out by our authorised service branch.
zProcessing of warranty claims
To ensure prompt processing of your claim, please follow the instructions
given below. Please retain proof of purchase and the article number
(e.g. IAN) for all inquiries. The product number can be found on the type
plate, an engraving, the cover page of your instructions (bottom left), or
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94

ULTIMATE SPEED Car and Motorcycle Battery Charger Manuel utilisateur

Catégorie
Chargeurs de batterie
Taper
Manuel utilisateur