ULTIMATE SPEED Car and Motorcycle Battery Charger Manuel utilisateur

CAR & MOTORCYCLE

BATTERY CHARGER ULGD 5.0 C1

IAN 373295_2104

BATTERILADER TIL BIL

Oversættelse af den originale driftsvejledning

DK

KFZ-BATTERIELADEGERÄT

Originalbetriebsanleitung

DE AT CH

CHARGEUR DE BATTERIE POUR VOITURE

Traduction du mode d’emploi d‘origine

FR BE

VOERTUIG-ACCULADER

Vertaling van de originele bedieningshandleiding

NL BE

CAR & MOTORCYCLE BATTERY CHAR

GER

Translation of the original instructions

GB IE NI

NL BE

DK

GB IE NI

Before reading, unfold the page containing the illustrations

and familiarise yourself with all functions of the device.

DK

Før du læser, vend siden med billeder frem og bliv

bekendt med alle apparatets funktioner.

FR BE

Avant de lire le document, allez à la page avec les

illustrations et étudiez toutes les fonctions de l’appareil.

NL BE

Klap, voordat u begint te lezen, de pagina met

afbeeldingen uit en maak u aansluitend vertrouwd

met alle functies van dit apparaat.

DE AT CH

Klappen Sie vor dem Lesen die Seite mit den Abbildungen

aus und machen Sie sich anschließend

mit allen Funktionen des Gerätes vertraut.

GB / IE / NI Translation of the original instructions Page 5

DK Brugs- og sikkerhedsanvisninger Side 22

FR / BE Traduction du mode d’emploi d‘origine Page 39

NL / BE Vertaling van de originele bedieningshandleiding Pagina 58

DE / AT / CH Originalbedienungsanleitung Seite 76

A

891011

2 3 4 6 71

B

C

5

12

14

15

16

V7.5-10.5 10.5-12.8 14.1 14.4 14.4 12.8

A0.8 5.0 3.0 0.8 0.1 0.8

1 2 3 4 5 6 7

13

GB/IE/NI 5

zTable of pictograms used

Read the instruction

manual of this product

attentively and with care

before use.

220 -

240

V~

50Hz

Alternating voltage 220

– 240 V with a frequency

of 50 Hz

NOTE:

This symbol indicates

additional information

and explanations on the

product and its use.

Caution!

Possible risks!

Caution!

Explosion hazard!

Caution! Risk of electric

shock!

T3.15A

Internal fuse

Dispose of the batteries

in the speciﬁed battery

collection points.

IP65 Protected against jets of

water and dust-proof

Only for use in closed,

ventilated rooms!

Do not dispose of any

electrical devices in

domestic waste!

Packaging material –

corrugated paper

Dispose of packaging

properly. Do not dispose

of the appliance in house-

hold waste!

Table of pictograms used ............................................... Page 5

Introduction ..................................................................... Page 6

Intended use .................................................................... Page 6

Package contents .............................................................. Page 7

Equipment ....................................................................... Page 7

Technical speciﬁcations ..................................................... Page 8

Charging characteristics .................................................... Page 8

Safety instructions .......................................................... Page 8

Speciﬁc safety instructions ............................................. Page 14

Before use ........................................................................ Page 14

Using the device .............................................................. Page 15

Connection ...................................................................... Page 15

Disconnecting................................................................... Page 15

Standby / Measuring battery voltage .................................. Page 16

6 V batteries .................................................................... Page 16

12 V batteries .................................................................. Page 16

Revival ............................................................................ Page 16

Selecting programs ........................................................... Page 16

Maintenance and care .................................................... Page 18

Information about recycling and disposal .................... Page 18

EU Declaration of Conformity ........................................ Page 19

Warranty and service information ................................ Page 20

Warranty conditions.......................................................... Page 20

Warranty period and statutory claims for defects .................. Page 20

Extent of warranty ............................................................. Page 20

Processing of warranty claims ............................................ Page 20

6GB/IE/NI

Suitable for motorbikes

(Program 2) Suitable for cars

(Program 3)

Suitable for the charging

of 12-V batteries Suitable for the charging

of 6-V batteries

Direct current Made from recycled

material

6 V – Mode

(Program 1) Protection class II

Protect electrical connec-

tions from rain! Winter – AGM – Mode

(Program 4)

Do not smoke! Avoid ﬂames and sparks!

Car and motorcycle battery charger ULGD 5.0 C1

zIntroduction

Congratulations! You have purchased one of our high- quality products.

Please familiarise yourself with the product before using it for the ﬁrst

time. To do so, please read through the following operating and safety

instructions carefully.

KEEP OUT OF THE REACH OF CHILDREN!

zIntended use

The Ultimate Speed ULGD 5.0 C1 is a multi-level car and motorcycle bat-

tery charger, which is suitable for charging and trickle charging 6 V- (3

cells) or 12 V (6 cells) lead acid batteries with electrolyte solution (WET),

with electrolyte absorbing mats (AGM), with gel gel-type electrolyte (GEL)

or calcium batteries. The device is not suitable for charging lithium-ion

batteries!

You can also regenerate discharged batteries (depending on the battery

type). The car and motorcycle battery charger has a safety circuit against

sparking and overheating. Keep these instructions in a safe place. Ensure

you hand over all documentation when passing the product on to anyone

else. Any use that differs to the intended use as stated above is prohi-

bited and potentially dangerous. Damage or injury caused by misuse

or disregarding the above warning is not covered by the warranty or

any liability on the part of the manufacturer. The device is not intended

for commercial use and should only be used indoors. Commercial use

will void the guarantee. The product must only be started up initially by

people who have been trained to do so.

NOTE:

The car and motorcycle battery charger cannot charge any electrical

vehicles with integrated rechargeable battery.

GB/IE/NI 7

NOTE:

No jumpstart of 6V or 12 V batteries possible.

zPackage contents

1 Car and motorcycle battery charger

1 Operating instructions

zEquipment

To do this see Fig. A, B:

After unpacking the product, please check that all of the package con-

tents are present and that the battery charger is in perfect condition. Do

not use the device if it is defective.

1Car and motorcycle battery charger

2LED reverse polarity (red)

3Standby LED (green)

412 V / 0.8 A (Program 2)

5 12 V / 5.0 A (Program 3)

6 12 V / 5.0 A (Program 4)

7 6 V / 0.8 A (Program 1)

8Charging display

9Status display

10 Voltage display

11 Program selector button

12 Mains cable

13 Positive pole connection terminal (red)

14 Negative pole connection terminal (black)

15 Positive pole connection cable (red)

16 Negative pole connection cable (black)

NOTE:

The use of the term ‘product’ or ‘device’ in the following text refers to the

car and motorcycle battery charger named in these operating instruc-

tions.

8GB/IE/NI

zTechnical speciﬁcations

Model: ULGD 5.0 C1

Rated voltage: 220-240 V~ 50 Hz

Rated intake current: 0,8 A

Rated output DC

voltage: 6 V / 12 V

Rated output direct current: 0,8 A / 5,0 A

Ambient temperature: -20 °C to 50 °C

Housing protection type: IP 65

Appliance class: II (dual insulation)

Battery types:

6 V lead acid battery,

1.2 Ah – 14 Ah

12 V lead acid battery,

1.2 Ah – 120 Ah

zCharging characteristics

To do this see Fig. C:

1Reverse polarity and diagnosis

2Recharge / desulphation

3Start of charging with a high current strength

4Charging up to 80%

5Absorption – charging up to 100%

6Trickle charging and monitoring

7Demand recharging

Changes to technical and visual aspects of the product may be made

as part of future developments without notice. Accordingly, no warranty

is offered for the physical dimensions, information and speciﬁcations in

these operating instructions. The operating instructions cannot therefore

be used as the basis for asserting a legal claim.

zSafety instructions

PLEASE READ THROUGH THE INST-

RUCTION MANUAL CAREFULLY

BEFORE USE. THESE FORM PART OF

GB/IE/NI 9

THE PRODUCT AND MUST BE AVAILABLE

AT ALL TIMES! KEEP OUT OF THE REACH

OF CHILDREN!

 The charger is only suitable for indoor

operation!

 DANGER!

Avoid danger to life and danger of injury

from improper use!

 CAUTION!

Do not operate the device with a damaged

cable, mains cable or mains plug. Damaged

mains cables pose danger to life from electric

shock.

 In case of damage, the mains cable must only

be repaired by authorized and trained specia-

lists! Contact the service point of your country

if you need any repair!

 DANGER OF ELECTRIC SHOCK!

Ensure that the vehicle is not in operation

if the battery is installed ﬁrmly in the vehicle!

Switch off the ignition and put the vehicle into

the parking position, with the parking brake

engaged (e.g. car) or the rope attached

(e.g. boat)!

 DANGER OF ELECTRIC SHOCK!

Disconnect the car and motorcycle

battery charger from the mains before remo-

ving the connection terminals.

 Connect the connection terminal that is not

connected to the car body ﬁrst.

 Connect the other connection terminal to the

car body away from the battery and the gaso-

line line.

 Connect the car and motorcycle battery char-

ger to the supply grid only after doing this.

 Disconnect the car and motorcycle battery

charger from the supply grid after charging.

 Only then disconnect the connection terminal

from the car body. Then disconnect the con-

nection terminal from the battery.

10 GB/IE/NI

 DANGER OF ELECTRIC SHOCK!

Only touch the pole connection terminals

(„–“ and „+“) in the insulated area!

 DANGER OF ELECTRIC SHOCK!

Conduct the connection to the battery

and the socket of the mains grid completely

protected from moisture!

 DANGER OF ELECTRIC SHOCK!

Perform installation, servicing and main-

tenance of the car and motorcycle battery

charger only when the mains current is not

connected!

 DANGER OF ELECTRIC SHOCK!

First disconnect the negative pole con-

nection cable (black) of the car and motorcyc-

le battery charger from the negative pole of

the battery upon completing the charging and

trickle charging process, if the battery is

continually connected in the vehicle.

 Do not leave any toddlers or children unsuper-

vised around the car and motorcycle battery

charger!

 Children cannot assess possible dangers in

use of electrical devices. Children must be su-

pervised to ensure that they do not play with

the device.

 EXPLOSION HAZARD!

Protect yourself from highly explosive

oxyhydrogen reactions! Gaseous hydrogen

can escape during charging or maintenance

charging of the battery. Oxyhydrogen is a

potentially explosive mix of gaseous hydrogen

and oxygen. The oxyhydrogen reaction occurs

at contact with open ﬁre (ﬂames, smouldering

or sparks)! Perform charging and maintenan-

ce charging in a weather-protected space that

is ventilated well. Ensure that there are no

naked ﬂames (ﬂames, smouldering or sparks)

during charging or maintenance charging!

GB/IE/NI 11

 EXPLOSION AND FIRE HAZARDS!

Ensure that explosive or ﬂammable substan-

ces, such as gasoline or solvents cannot be

ignited when you are using the car and motor-

cycle battery charger!

 EXPLOSIVE GASES!

Avoid ﬂames and sparks!

 Ensure sufﬁcient ventilation when charging.

 Put the battery onto a well-ventilated surface

when charging. Otherwise, the device can

be damaged.

 EXPLOSION HAZARD!

Ensure that the positive pole connection

cable has no contact with a fuel line (e.g.

petrol line)!

 DANGER OF CAUSTIC BURNS!

Protect your eyes and skin from caustic burns

from the acid (sulphuric acid) when it comes

into contact with the battery!

 Use: acid-resistant safety goggles, clothing

and gloves! If your eyes or skin have come

into contract with the sulphuric acid, ﬂush the

affected body region with plenty of clear, run-

ning water and seek medical advice at once!

 Avoid electrical short circuits when connecting

the car and motorcycle battery charger to the

battery. Connect the minus pole connection

cable only to the minus pole of the battery or

the car body. Connect the plus pole connec-

tion cable only to the plus pole of the battery!

 Before connecting to the mains, verify the

mains power has the required 230 V~ 50 Hz,

a 16A fuse and an ELCB switch (earth leaka-

ge circuit breaker)! Otherwise, the device can

be damaged.

 Do not use the car and motorcycle battery

charger near any ﬁres, heat and long-term

temperatures above 50°C! For higher

temperatures, the output power of the car

and motorcycle battery charger will drop au-

tomatically.

 Only use the car and motorcycle battery char-

ger with the original parts it was

12 GB/IE/NI

delivered with!

 Do not cover the car and motorcycle battery

charger with any objects! Otherwise, the de-

vice can be damaged.

 Protect the electrical contact surfaces of the

battery from short circuit!

 Only use the car and motorcycle battery char-

ger for the charging and maintenance char-

ging of undamaged 6V-/12V-lead batteries

(with electrolyte solution or gel)! Otherwise,

property damage may be the consequence.

 Do not use the car and motorcycle battery

charger for the charging and maintenance

charging of non-rechargeable batteries. Ot-

herwise, property damage may be the conse-

quence.

 Do not use the car and motorcycle battery

charger for the charging and maintenance

charging of damaged or frozen batteries! Ot-

herwise, property damage may be the conse-

quence.

 Please refer to the original operating instruc-

tions about the maintenance of your battery

prior to connecting the car and motorcycle

battery charger! Otherwise, there is a danger

of injury and/or the risk of damage to the de-

vice.

 Before connecting the car and motorcycle

battery charger to a battery that is continually

connected to the vehicle, learn about compli-

ance with the electrical safety and maintenan-

ce in the original operating instructions of the

vehicle! Otherwise, there is a danger of injury

and/or the risk of property damage.

 Disconnect the car and motorcycle battery

charger from the mains current when it is not

is use to protect the environment as well!

Note that power is consumed in standby ope-

ration as well.

 Always pay attention and be aware of what

you are doing. Proceed reasonably and do

not put the car and motorcycle battery char-

ger into operation when you are not focused

or not feeling well.

GB/IE/NI 13

Personal safety:

 This device may be used by children aged

8years and older, and by persons with redu-

ced physical, sensory or mental capacities, or

a lack of experience and knowledge, if they

are supervised or have been instructed in how

to use the device safely and understand the

dangers that may arise when using it.

Do not allow children to play with the device.

Cleaning and day-to-day maintenance must

not be performed by children without super-

vision.

 Children must be supervised to ensure that

they do not play with the device.

 Keep the device away from people –

especially children – and household pets.

 Within the working area, the user is responsi-

ble for any damage or injury to third parties

that was caused by the use of the device.

 Do not leave the device charging unattended.

 Keep the device in a dry location and out of

the reach of children.

This helps prevent device damage

and possible personal injuries that

could result from it:

Working with the device:

 Before setup or ﬁrst use, check the device for

any damage and do not use unless in perfect

working order.

 Make sure that the mains plug and connection

terminals do not get wet. Do not expose the

device to rain or wet weather. Do not let the

device come into contact with water. Do not

immerse the device in water. There is a risk of

electric shock!

 In hot weather, do not leave the device in a

car. This could permanently damage the de-

vice.

 Do not operate the device near to ﬂammable

liquids or gases. Failure to do so risks causing

a ﬁre or explosion!

 Switch the device off and remove the mains

14 GB/IE/NI

plug from the socket in the following cases:

–When you are not using the device;

–If you are leaving the device unsupervised;

–If you are doing cleaning work;

–If the connection cable is damaged;

 Only use the accessories supplied and

recommended by the manufacturer.

 Do not disassemble or modify the car and mo-

torcycle battery charger. This device must only

be repaired by a maintenance technician.

 Do not use the device in areas with a risk of

explosion, e.g. near ﬂammable liquids, gases

or powders.

 Do not expose the device to any source of

heat.

 CAUTION: How to avoid accidents

and injuries from electric shock:

Electrical safety:

 Do not carry the device by the cable. Do not

unplug the plug from the socket by pulling on

the cable. Protect the cable from heat, oil and

sharp edges.

 If the cable is damaged, unplug the plug im-

mediately from the socket.

zSpeciﬁc safety instructions

 A slightly higher temperature during charging

is absolutely normal and not a malfunction.

 Protect the car and motorcycle battery charger

1 from moisture and high temperatures, inclu-

ding ﬁres.

 Store the car and motorcycle battery charger

1 in a dry place and protect the device from

moisture and corrosion.

 Do not drop the car and motorcycle battery

charger 1 while it is being used.

zBefore use

 Take all parts from the packaging and check whether the device or

parts show any damage. If this is the case, do not use the device.

GB/IE/NI 15

Contact the manufacturer via the indicated service address. Remove

all protective ﬁlms and other transport packaging. Check that the de-

livery is complete.

 Always pull the mains plug from the socket before you perform any

work at the car and motorcycle battery charger 1.

 Before connecting the charger please read the user instructions for

the battery.

 In addition, you must adhere to the instructions from the vehicle ma-

nufacturer where a battery is continuously connected in the vehicle.

Secure the car or motorcycle, switch the ignition off.

 Clean the battery poles. Make sure that the dirt does not come into

contact with your eyes.

 Make sure that there is sufﬁcient ventilation.

NOTE: The ambient temperature is measured in the charger. Hence, for

optimum function, make sure the battery exhibits the same temperature as

the environment.

zUsing the device

zConnection

NOTE:

Always observe the instructions from the vehicle manufacturer or the

battery manufacturer.

 Disconnect the minus pole connection cable (black) of the vehicle

from the minus pole of the battery ﬁrst before charging and mainte-

nance charging if the battery is continually connected in the vehicle.

The minus pole of your battery is usually connected to the car body

of the vehicle.

 Then disconnect the plus pole connection cable (red) of the vehicle

from the plus pole of the battery.

 Only then connect the „+“ pole quick-contact connection terminal

(red) 13 of the car and motorcycle battery charger to the „+“ pole of

the battery.

 Connect the „–“ pole quick-contact connection terminal (black) 14 to

the „–“ pole of the battery. Connect the mains cable 12 of the car

and motorcycle battery charger 1to the socket.

 If the output terminals are connected in reverse the red LED reverse

polarity 2lights up.

zDisconnecting

 Disconnect the device from the mains current.

 Disconnect the „–“ pole quick-contact connection terminal (black) 14

from the „–“ pole of the battery.

 Disconnect the „+“-pole quick contact-connection terminal (red) 13

from the „+“-pole of the battery.

 Reconnect the plus pole connection cable of the battery to the plus

pole of the battery.

 Reconnect the minus pole connection cable of the battery to the mi-

nus pole of the battery.

16 GB/IE/NI

zStandby / Measuring battery voltage

After connecting the mains supply, the device is in standby mode. The

standby display 3lights up green. When the connection terminals are

connected, the battery voltage is displayed in the LC display (voltage

display 10 ). The segments of the status display 9are empty. If the

measured voltage is below 3.8 V or above 15V, then this means the

battery is not charging. The error message

„Err“ will be shown brieﬂy in the display. The device switches to standby.

z6 V batteries

If a battery is measured in the voltage range 3.7 – 7.3 V, then you can

only select Program 1.

z12 V batteries

If a battery is identiﬁed as being in the critical voltage range from 7.3 –

10.5 V, then the device will check whether it is a fully-charged 6 V

battery or a discharged 12 V battery. Press the program selector button

11 to select a program. The device carries out a test measurement

procedure for approx. 90 seconds. The display will show:

If after approx. 90 seconds, the identiﬁed value is between 7.3 – 7.5 V,

then the 12 V battery is defective. The device switches to standby.

zRevival

If after approx. 90 seconds, the identiﬁed value is between 7.5 – 10.5 V,

then a 12 V battery is present. The charging process starts with pulse

operation for revival of the battery. The voltage display 10 ﬂashes. Once

10.5 V is reached, the device switches to further charging levels.

The revival procedure is identical for all 12 V charging programs.

zSelecting programs

Note:

If a battery is identiﬁed in the voltage range of 3.7 – 7.3V, then

programs 2-3-4 cannot be selected. The charging process continues

automatically. Depending on the program selected, the charging charac-

teristics for voltage, time and temperature are monitored. With diagnosis

program, revival mode and trickle charging.

Program max. (V) max. (A)

17.3 V 0.8 A

GB/IE/NI 17

214.4 V 0.8 A

314.4 V 5.0 A

414.7 V 5.0 A

Program 1 , „6 V“, (7.3 V / 0.8 A)

To charge 6 V batteries with a capacity less than 14 Ah.

Press the program selector button 11 to select Program 1.

The symbol 7is shown in the LC display. During the charging

process, the charging display 8ﬂashes and shows how far the charging

process has progressed (1 – 4bars). When the battery is fully charged,

the status display 9shows 4 bars. The ﬂashing stops and the device

switches to trickle charging automatically.

Program 2 , „12 V“, (14.4 V / 0.8 A)

To charge 12 V batteries with a capacity less than 14 Ah.

Press the program selector button 11 to select Program 2. The symbol

4is shown in the LC display. During the charging process, the charging

display 8ﬂashes and shows how far the charging process has progres-

sed (1 – 4 bars). When the battery is fully charged, the status display 9

shows 4 bars. The ﬂashing stops and the device switches to trickle

charging automatically.

Program 3 , „12 V“, (14.4 V / 5.0 A)

To charge 12 V batteries with a capacity of 14 Ah – 120 Ah. Press the

program selector button 11 to select Program 3. The symbol 5is

shown in the LC display. During the charging process, the charging

display 8ﬂashes and shows how far the charging process has progres-

sed (1 – 4 bars). When the battery is fully charged, the status display 9

shows 4 bars. The ﬂashing stops and the device switches to trickle

charging automatically.

Program 4 , „12 V“, (14.7 V / 5.0 A)

To charge 12 V batteries with a capacity of 14 Ah – 120 Ah under cold

conditions or to charge AGM batteries. Press the program selector button

11 to select Program 4.

NOTE:

This program starts, with a slight time delay if necessary.

The symbol 6is shown in the LC display. During the charging

process, the charging display 8ﬂashes and shows how far the charging

process has progressed (1 – 4 bars). When the battery is fully charged,

the status display 9shows 4 bars. The ﬂashing stops and the device

switches to trickle charging automatically.

18 GB/IE/NI

Trickle charging

As described in „Selecting programs“, the device has an automatic trickle

charging procedure. Depending on the drop in voltage in the batte-

ry – through self-discharge – the charger reacts with different levels of

charging current. The battery can remain connected to the charger over a

longer period of time.

Device protection function

As soon as a different situation occurs, such as a short circuit, critical

drop in voltage during the charging process, open circuit or reversed

connection of the output terminals, the battery charger 1switches off

automatically. The electronic system resets the system immediately to its

home position, in order to avoid damage. If the device should become

too hot during charging, the output power is automatically reduced. This

protects the device from damage.

zMaintenance and care

 Always pull the mains cable 12 from the socket before you perform

any work on the car and motorcycle battery charger 1.

 The device is maintenance-free. Deactivate the device. Clean the me-

tal and plastic surfaces of the device with a dry cloth.

 Never use any solvents or other aggressive cleaning agents.

zInformation about recycling and disposal

DO NOT DISPOSE OF ELECTRICAL TOOLS IN HOUSE-

HOLD WASTE!

Please return this device, accessories and packaging to your local

recycling depot. Do not dispose of the car and motorcycle battery

charger in household waste, in ﬁre or in water. Devices that are

no longer functional should be recycled wherever possible. Ask your

local stockist for advice.

As the consumer you are legally obliged (by the German Battery

Ordinance) to return any and all used batteries. Batteries

containing harmful substances are labelled with the adjacent

symbol, which indicates the prohibition on disposal in household waste.

The abbreviations for the relevant heavy metals are: Cd = cadmium,

Hg = mercury, Pb = lead.

Take used batteries to a waste management company in your city or com-

munity or return them to your dealer. This satisﬁes your legal obligations

while also making an important contribution to protecting the environ-

ment.

Note the labelling on the packaging and separate the packaging

material components for disposal if necessary. The packaging

material is labelled with abbreviations (a) and numbers (b) with

the following meanings: 1–7: Plastics, 20–22: Paper and cardboard,

80–98: Composites.

GB/IE/NI 19

zEU Declaration of Conformity

We,

C. M. C. GmbH

Responsible for documentation:

Dr Christian Weyler

Katharina-Loth-Str. 15

66386 St. Ingbert

hereby take sole responsibility for declaring that the product

Car & motorcycle battery charger

Year of manufacture: 2022/04

IAN: 373295_2104

Model: ULGD 5.0 C1

Model number: 2406

meets the basic safety requirements as speciﬁed in the European Directi-

ves

Low Voltage Directive

2014/35/EU

Electromagnetic Compatibility

2014/30/EU

RoHS Directive

2011/65/EU + 2015/863/EU

and the amendments to these Directives.

The object of the declaration described above meets the requirements of

Directive 2011/65/EU of the European Parliament and of the Council of

8 June 2011 on the restriction of the use of certain hazardous substan-

ces in electrical and electronic equipment. This conformity assessment is

based on the following harmonised standards:

EN 60335-2-29:2004/A11:2018

EN 60335-1:2012/A2:2019

EN 62233:2008

EN 55014-1:2017

EN 55014-2:2015

EN 61000-3-2:2019

EN 61000-3-3:2013+A1:2019

St. Ingbert, 01.06.2021

On behalf of Dr Christian Weyler

– Quality Assurance –

20 GB/IE/NI

zWarranty and service information

Warranty from Creative Marketing & ConsultingGmbH

Dear Customer,

The warranty for this equipment is 3 years from the date of purchase. In

the event of product defects, you have legal rights against the retailer

of this product. Your statutory rights are not affected in any way by our

warranty conditions, which are described below.

zWarranty conditions

The warranty period begins on the date of purchase. Please retain the ori-

ginal sales receipt. This document is required as your proof of purchase.

Should this product show any defect in materials or manufacture within

3 years from the date of purchase, we will repair or replace it – at our

discretion – free of charge. This warranty service requires that you retain

proof of purchase (sales receipt) for the defective device for the three

year period and that you brieﬂy explain in writing what the fault entails

and when it occurred. If the defect is covered by our warranty, we will

repair and return your product or send you a replacement. The original

warranty period is not extended when a device is repair or replaced.

zWarranty period and statutory claims for

defects

The warranty period is not extended by the guarantee. This also applies

to replaced and repaired parts. Any damages or defects detected at the

time of purchase must be reported immediately after unpacking. Any

incidental repairs after the warranty period are subject to a fee.

zExtent of warranty

This device has been manufactured according to strict quality guidelines

and carefully inspected before delivery. The warranty applies to material

and manufacturing defects only. This warranty does not extend to product

parts, which are subject to normal wear and tear and can thus be regar-

ded as consumable parts, or for damages to fragile parts, e.g. switches,

rechargeable batteries or parts made from glass. This warranty is voided

if the product becomes damaged or is improperly used or maintained.

For proper use of the product, all of the instructions given in the operating

instructions must be followed precisely. If the operating instructions advise

you or warn you against certain uses or actions, these must be avoided

in all circumstances. The product is for consumer use only and is not inten-

ded for commercial or trade use. The warranty becomes void in the event

of misuse and improper use, use of force, and any work on the device

that has not been carried out by our authorised service branch.

zProcessing of warranty claims

To ensure prompt processing of your claim, please follow the instructions

given below. Please retain proof of purchase and the article number

(e.g. IAN) for all inquiries. The product number can be found on the type

plate, an engraving, the cover page of your instructions (bottom left), or

La page charge ...

ULTIMATE SPEED Car and Motorcycle Battery Charger Manuel utilisateur

ULTIMATE SPEED Car and Motorcycle Battery Charger Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents