Espressif ESP32­-C3­-Mini-1U General-Purpose Wi-Fi and Bluetooth LE Module Manuel utilisateur

Catégorie
Antennes réseau
Taper
Manuel utilisateur

Ce manuel convient également à

ESP32C3MINI1U/
CBL-WCT-C3
User Manual
Pre-release v0.1
Espressif Systems
Copyright © 2022
www.espressif.com
About This Document
This user manual shows how to get started with the ESP32-C3-MINI-1U module.
Document Updates
Please always refer to the latest version on https://www.espressif.com/en/support/download/documents.
Revision History
For revision history of this document, please refer to the last page.
Documentation Change Notification
Espressif provides email notifications to keep you updated on changes to technical documentation. Please sub-
scribe at www.espressif.com/en/subscribe.
Certification
Download certificates for Espressif products from www.espressif.com/en/certificates.
Contents
Contents
1 Overview 4
1.1 Module Overview 4
1.2 Pin Description 5
2 Get Started on ESP32C3MINI1U 7
2.1 What You Need 7
2.2 Hardware Connection 7
2.3 Set up Development Environment 8
2.3.1 Install Prerequisites 8
2.3.2 Get ESP-IDF 8
2.3.3 Set up Tools 9
2.3.4 Set up Environment Variables 9
2.4 Create Your First Project 9
2.4.1 Start a Project 9
2.4.2 Connect Your Device 9
2.4.3 Configure 9
2.4.4 Build the Project 10
2.4.5 Flash onto the Device 11
2.4.6 Monitor 12
3 U.S. FCC Statement 14
4 IC Statement 18
5 Learning Resources 21
5.1 Must-Read Documents 21
5.2 Important Resources 21
Revision History 22
Espressif Systems 3 ESP32-C3-MINI-1U User Manual v0.1
1 Overview
1 Overview
1.1 Module Overview
ESP32-C3-MINI-1U is a general-purpose Wi-Fi and Bluetooth LE module. The rich set of peripherals and a small
size make this module an ideal choice for smart homes, industrial automation, health care, consumer electronics,
etc.
Table 1: ESP32C3MINI1U Specifications
Categories Parameters Specifications
Wi-Fi Protocols 802.11 b/g/n (up to 150 Mbps)
Frequency range 2412 ~2462 MHz
Bluetooth®Protocols Bluetooth®LE: Bluetooth 5 and Bluetooth mesh
Radio Class-1, class-2 and class-3 transmitter
Hardware
Module interfaces
GPIO, SPI, UART, I2C, I2S, remote control peripheral,
LED PWM controller, general DMA controller, TWAI®
controller (compatible with ISO 11898-1), temperature
sensor, SAR ADC
Integrated crystal 40 MHz crystal
Operating voltage/Power supply 3.0 V ~3.6 V
Operating current Average: 80 mA
Minimum current delivered by power
supply 500 mA
Ambient temperature –40 °C ~+105 °C
Moisture sensitivity level (MSL) Level 3
Espressif Systems 4 ESP32-C3-MINI-1U User Manual v0.1
1 Overview
1.2 Pin Description
Pin 49
GND
GND GND GND
GNDGND
GND GND GND
Pin 1
Pin 2
Pin 3
Pin 4
Pin 6
Pin 5
Pin 7
Pin 8
Pin 9
Pin 10
Pin 11
Pin 53
GND
Pin 52
GND
Pin 12
Pin 13
Pin 14
Pin 15
Pin 16
Pin 17
Pin 18
Pin 19
Pin 20
Pin 21
Pin 22
Pin 23
Pin 24
Pin 25
Pin 51
GND
Pin 26
Pin 27
Pin 28
Pin 29
Pin 30
Pin 31
Pin 32
Pin 33
Pin 34
Pin 35
Pin 50
GND
Pin 36
Pin 37
Pin 38
Pin 39
Pin 40
Pin 41
Pin 42
Pin 43
Pin 44
Pin 45
Pin 46
Pin 47
Pin 48
GND
GND
3V3
NC
IO2
IO3
NC
EN
NC
NC
GND
IO0
IO1
GND
NC
IO10
NC
IO4
IO5
IO6
IO7
IO8
IO9
NC
NC
IO18
IO19
NC
NC
RXD0
TXD0
NC
NC
NC
NC
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
Keepout Zone
Figure 1: Pin Layout (Top View)
The module has 53 pins. See pin definitions in Table 2.
For peripheral pin configurations, please refer to ESP32-C3 Series Datasheet .
Table 2: Pin Definitions
Name No. Type Function
GND 1, 2, 11, 14, 36-53 P Ground
3V3 3 P Power supply
NC 4 — NC
IO2 5 I/O/T GPIO2, ADC1_CH2, FSPIQ
IO3 6 I/O/T GPIO3, ADC1_CH3
NC 7 — NC
EN 8 I
High: on, enables the chip.
Low: off, the chip powers off.
Note: Do not leave the EN pin floating.
NC 9 — NC
NC 10 — NC
Cont’d on next page
Espressif Systems 5 ESP32-C3-MINI-1U User Manual v0.1
1 Overview
Table 2 – cont’d from previous page
Name No. Type Function
IO0 12 I/O/T GPIO0, ADC1_CH0, XTAL_32K_P
IO1 13 I/O/T GPIO1, ADC1_CH1, XTAL_32K_N
NC 15 — NC
IO10 16 I/O/T GPIO10, FSPICS0
NC 17 — NC
IO4 18 I/O/T GPIO4, ADC1_CH4, FSPIHD, MTMS
IO5 19 I/O/T GPIO5, ADC2_CH0, FSPIWP, MTDI
IO6 20 I/O/T GPIO6, FSPICLK, MTCK
IO7 21 I/O/T GPIO7, FSPID, MTDO
IO8 22 I/O/T GPIO8
IO9 23 I/O/T GPIO9
NC 24 — NC
NC 25 — NC
IO18 26 I/O/T GPIO18
IO19 27 I/O/T GPIO19
NC 28 — NC
NC 29 — NC
RXD0 30 I/O/T GPIO20, U0RXD,
TXD0 31 I/O/T GPIO21, U0TXD
NC 32 — NC
NC 33 — NC
NC 34 — NC
NC 35 — NC
Espressif Systems 6 ESP32-C3-MINI-1U User Manual v0.1
2 Get Started on ESP32-C3-MINI-1U
2 Get Started on ESP32C3MINI1U
2.1 What You Need
To develop applications for ESP32-C3-MINI-1U module you need:
1 x ESP32-C3-MINI-1U module
1 x Espressif RF testing board
1 x USB-to-Serial board
1 x Micro-USB cable
1 x PC running Linux
In this user guide, we take Linux operating system as an example. For more information about the configuration
on Windows and macOS, please refer to ESP-IDF Programming Guide.
2.2 Hardware Connection
1. Solder the ESP32-C3-MINI-1U module to the RF testing board as shown in Figure 2.
Figure 2: Hardware Connection
2. Connect the RF testing board to the USB-to-Serial board via TXD, RXD, and GND.
3. Connect the USB-to-Serial board to the PC.
4. Connect the RF testing board to the PC or a power adapter to enable 5 V power supply, via the Micro-USB
cable.
5. During download, connect IO0 to GND via a jumper. Then, turn ”ON” the testing board.
6. Download firmware into flash. For details, see the sections below.
Espressif Systems 7 ESP32-C3-MINI-1U User Manual v0.1
2 Get Started on ESP32-C3-MINI-1U
7. After download, remove the jumper on IO0 and GND.
8. Power up the RF testing board again. ESP32-C3-MINI-1U will switch to working mode. The chip will read
programs from flash upon initialization.
Note:
IO0 is internally logic high. If IO0 is set to pull-up, the Boot mode is selected. If this pin is pull-down or left floating, the
Download mode is selected. For more information on ESP32-C3-MINI-1U, please refer to
ESP32-C3-MINI-1 & ESP32-C3-MINI-1U Datasheet .
2.3 Set up Development Environment
The Espressif IoT Development Framework (ESP-IDF for short) is a framework for developing applications based on
the Espressif chips. Users can develop applications with ESP chips in Windows/Linux/macOS based on ESP-IDF.
Here we take Linux operating system as an example.
2.3.1 Install Prerequisites
To compile with ESP-IDF you need to get the following packages:
CentOS 7:
1sudo yum install git wget flex bison gperf python cmake ninja-build ccache dfu-
util
Ubuntu and Debian (one command breaks into two lines):
1sudo apt-get install git wget flex bison gperf python python-pip python-
setuptools cmake
2ninja-build ccache libffi-dev libssl-dev dfu-util
• Arch:
1sudo pacman -S --needed gcc git make flex bison gperf python-pip cmake ninja
ccache dfu-util
Note:
This guide uses the directory ~/esp on Linux as an installation folder for ESP-IDF.
Keep in mind that ESP-IDF does not support spaces in paths.
2.3.2 Get ESPIDF
To build applications for ESP32-C3-MINI-1U module, you need the software libraries provided by Espressif in
ESP-IDF repository.
To get ESP-IDF, create an installation directory (~/esp) to download ESP-IDF to and clone the repository with ‘git
clone’:
1mkdir -p ~/esp
2cd ~/esp
3git clone --recursive https://github.com/espressif/esp-idf.git
Espressif Systems 8 ESP32-C3-MINI-1U User Manual v0.1
2 Get Started on ESP32-C3-MINI-1U
ESP-IDF will be downloaded into ~/esp/esp-idf. Consult ESP-IDF Versions for information about which ESP-IDF
version to use in a given situation.
2.3.3 Set up Tools
Aside from the ESP-IDF, you also need to install the tools used by ESP-IDF, such as the compiler, debugger, Python
packages, etc. ESP-IDF provides a script named ’install.sh’ to help set up the tools in one go.
1cd ~/esp/esp-idf
2./install.sh
2.3.4 Set up Environment Variables
The installed tools are not yet added to the PATH environment variable. To make the tools usable from the command
line, some environment variables must be set. ESP-IDF provides another script ’export.sh’ which does that. In the
terminal where you are going to use ESP-IDF, run:
1. $HOME/esp/esp-idf/export.sh
Now everything is ready, you can build your first project on ESP32-C3-MINI-1U module.
2.4 Create Your First Project
2.4.1 Start a Project
Now you are ready to prepare your application for ESP32-C3-MINI-1U module. You can start with get-started/hello_world
project from examples directory in ESP-IDF.
Copy get-started/hello_world to ~/esp directory:
1cd ~/esp
2cp -r $IDF_PATH/examples/get-started/hello_world .
There is a range of example projects in the examples directory in ESP-IDF. You can copy any project in the same
way as presented above and run it. It is also possible to build examples in-place, without copying them first.
2.4.2 Connect Your Device
Now connect your ESP32-C3-MINI-1U module to the computer and check under what serial port the module is
visible. Serial ports in Linux start with ‘/dev/tty’ in their names. Run the command below two times, first with the
board unplugged, then with plugged in. The port which appears the second time is the one you need:
1ls /dev/tty*
Note:
Keep the port name handy as you will need it in the next steps.
2.4.3 Configure
Navigate to your ‘hello_world’ directory from Step 2.4.1. Start a Project, set ESP32-C3 as the target and run the
project configuration utility ‘menuconfig’.
Espressif Systems 9 ESP32-C3-MINI-1U User Manual v0.1
2 Get Started on ESP32-C3-MINI-1U
1cd ~/esp/hello_world
2idf.py set-target esp32c3
3idf.py menuconfig
Setting the target with ‘idf.py set-target esp32c3’ should be done once, after opening a new project. If the project
contains some existing builds and configuration, they will be cleared and initialized. The target may be saved in
environment variable to skip this step at all. See Selecting the Target for additional information.
If the previous steps have been done correctly, the following menu appears:
Figure 3: Project Configuration  Home Window
The colors of the menu could be different in your terminal. You can change the appearance with the option ‘-�-style’�.
Please run ‘idf.py menuconfig -�-help’�for further information.
2.4.4 Build the Project
Build the project by running:
1idf.py build
This command will compile the application and all ESP-IDF components, then it will generate the bootloader,
partition table, and application binaries.
1$ idf.py build
2Running cmake in directory /path/to/hello_world/build
3Executing ”cmake -G Ninja --warn-uninitialized /path/to/hello_world”...
4Warn about uninitialized values.
5-- Found Git: /usr/bin/git (found version ”2.17.0”)
6-- Building empty aws_iot component due to configuration
7-- Component names: ...
8-- Component paths: ...
9
10 ... (more lines of build system output)
11
Espressif Systems 10 ESP32-C3-MINI-1U User Manual v0.1
2 Get Started on ESP32-C3-MINI-1U
12 [527/527] Generating hello-world.bin
13 esptool.py v2.3.1
14
15 Project build complete. To flash, run this command:
16 ../../../components/esptool_py/esptool/esptool.py -p (PORT) -b 921600 write_flash --flash_
mode dio
17 --flash_size detect --flash_freq 40m 0x10000 build/hello-world.bin build 0x1000
18 build/bootloader/bootloader.bin 0x8000 build/partition_table/partition-table.bin
19 or run ’idf.py -p PORT flash’
If there are no errors, the build will finish by generating the firmware binary .bin file.
2.4.5 Flash onto the Device
Flash the binaries that you just built onto your ESP32-C3-MINI-1U module by running:
1idf.py -p PORT [-b BAUD] flash
Replace PORT with your module‘s serial port name from Step: Connect Your Device.
You can also change the flasher baud rate by replacing BAUD with the baud rate you need. The default baud rate
is 460800.
For more information on idf.py arguments, see idf.py.
Note:
The option ‘flash‘ automatically builds and flashes the project, so running ‘idf.py build‘ is not necessary.
1...
2esptool.py --chip esp32c3 -p /dev/ttyUSB0 -b 460800 --before=default_reset --after
=hard_reset write_flash --flash_mode dio --flash_freq 80m --flash_size 2MB 0x
8000 partition_table/partition-table.bin 0x0 bootloader/bootloader.bin 0x10000
hello-world.bin
3esptool.py v3.0
4Serial port /dev/ttyUSB0
5Connecting....
6Chip is ESP32-C3
7Features: Wi-Fi
8Crystal is 40MHz
9MAC: 7c:df:a1:40:02:a4
10 Uploading stub...
11 Running stub...
12 Stub running...
13 Changing baud rate to 460800
14 Changed.
15 Configuring flash size...
16 Compressed 3072 bytes to 103...
17 Writing at 0x00008000... (100 %)
18 Wrote 3072 bytes (103 compressed) at 0x00008000 in 0.0 seconds (effective 4238.1
kbit/s)...
19 Hash of data verified.
Espressif Systems 11 ESP32-C3-MINI-1U User Manual v0.1
2 Get Started on ESP32-C3-MINI-1U
20 Compressed 18960 bytes to 11311...
21 Writing at 0x00000000... (100 %)
22 Wrote 18960 bytes (11311 compressed) at 0x00000000 in 0.3 seconds (effective 584.9
kbit/s)...
23 Hash of data verified.
24 Compressed 145520 bytes to 71984...
25 Writing at 0x00010000... (20 %)
26 Writing at 0x00014000... (40 %)
27 Writing at 0x00018000... (60 %)
28 Writing at 0x0001c000... (80 %)
29 Writing at 0x00020000... (100 %)
30 Wrote 145520 bytes (71984 compressed) at 0x00010000 in 2.3 seconds (effective
504.4 kbit/s)...
31 Hash of data verified.
32
33 Leaving...
34 Hard resetting via RTS pin...
35 Done
If everything goes well, the “hello_world” application starts running after you remove the jumper on IO0 and GND,
and re-power up the testing board.
2.4.6 Monitor
To check if “hello_world” is indeed running, type ‘idf.py -p PORT monitor‘ (Do not forget to replace PORT with your
serial port name).
This command launches the IDF Monitor application:
1$ idf.py -p /dev/ttyUSB0 monitor
2Running idf_monitor in directory [...]/esp/hello_world/build
3Executing ”python [...]/esp-idf/tools/idf_monitor.py -b 115200 [...]/esp/hello_world/build
/hello-world.elf”...
4--- idf_monitor on /dev/ttyUSB0 115200 ---
5--- Quit: Ctrl+] | Menu: Ctrl+T | Help: Ctrl+T followed by Ctrl+H ---
6ets Jun 8 2016 00:22:57
7
8rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
9ets Jun 8 2016 00:22:57
10 ...
After startup and diagnostic logs scroll up, you should see “Hello world!” printed out by the application.
1...
2Hello world!
3Restarting in 10 seconds...
4This is esp32c3 chip with 1 CPU core, WiFi/BLE, 4MB external flash
5Restarting in 9 seconds...
6Restarting in 8 seconds...
7Restarting in 7 seconds...
To exit IDF monitor use the shortcut Ctrl+].
Espressif Systems 12 ESP32-C3-MINI-1U User Manual v0.1
2 Get Started on ESP32-C3-MINI-1U
That’s all what you need to get started with ESP32-C3-MINI-1U module! Now you are ready to try some other
examples in ESP-IDF, or go right to developing your own applications.
Espressif Systems 13 ESP32-C3-MINI-1U User Manual v0.1
3 U.S. FCC Statement
3 U.S. FCC Statement
The device complies with KDB 996369 D03 OEM Manual v01. Below are integration instructions for host product
manufacturers according to the KDB 996369 D03 OEM Manual v01.
List of Applicable FCC Rules
FCC Part 15 Subpart C 15.247 & 15.209
Specific Operational Use Conditions
The module has WiFi, BR, EDR, and BLE functions.
Operation Frequency:
WiFi: 2412 ~2462 MHz
Bluetooth: 2402 ~2480 MHz
Number of Channel:
WiFi: 12
Bluetooth: 40
• Modulation:
WiFi: DSSS; OFDM
Bluetooth: GFSK; π/4 DQPSK; 8 DPSK
Type: External antenna connector
Gain: 2.33 dBi Max
The module can be used for IoT applications with a maximum 2.33 dBi antenna. The host manufacturer installing
this module into their product must ensure that the final composit product complies with the FCC requirements by
a technical assessment or evaluation to the FCC rules, including the transmitter operation. The host manufacturer
has to be aware not to provide information to the end user regarding how to install or remove this RF module in
the user’s manual of the end product which integrates this module. The end user manual shall include all required
regulatory information/warning as show in this manual.
Limited Module Procedures
Not applicable. The module is a single module and complies with the requirement of FCC Part 15.212.
Trace Antenna Designs
Not applicable. The module has its own antenna, and does not need a host’s printed board microstrip trace
antenna, etc.
RF Exposure Considerations
The module must be installed in the host equipment such that at least 20cm is maintained between the antenna
and users’ body; and if RF exposure statement or module layout is changed, then the host product manufacturer
Espressif Systems 14 ESP32-C3-MINI-1U User Manual v0.1
3 U.S. FCC Statement
required to take responsibility of the module through a change in FCC ID or new application. The FCC ID of the
module cannot be used on the final product. In these circumstances, the host manufacturer will be responsible
for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.
Antennas
Antenna specification are as follows:
Type: External antenna connector
Gain: 2.33 dBi
This device is intended only for host manufacturers under the following conditions:
The transmitter module may not be co-located with any other transmitter or antenna.
The module shall be only used with the external antenna(s) that has been originally tested and certified with
this module.
The antenna must be either permanently attached or employ a ‘unique’ antenna coupler.
As long as the conditions above are met, further transmitter test will not be required. However, the host manufac-
turer is still responsible for testing their end-product for any additional compliance requirements required with this
module installed (for example, digital device emissions, PC peripheral requirements, etc.).
Label and Compliance Information
Host product manufacturers need to provide a physical or e-label stating “Contains FCC ID: 2AARRSF13569-1
with their finished product.
Information on test modes and additional testing requirements
Operation Frequency:
WiFi: 2412 ~2462 MHz
Bluetooth: 2402 ~2480 MHz
Number of Channel:
WiFi: 12
Bluetooth: 40
• Modulation:
WiFi: DSSS; OFDM
Bluetooth: GFSK; π/4 DQPSK; 8 DPSK
Host manufacturer must perform test of radiated and conducted emission and spurious emission, etc., according
to the actual test modes for a stand-alone modular transmitter in a host, as well as for multiple simultaneously
transmitting modules or other transmitters in a host product. Only when all the test results of test modes comply
with FCC requirements, then the end product can be sold legally.
Espressif Systems 15 ESP32-C3-MINI-1U User Manual v0.1
3 U.S. FCC Statement
Additional testing, Part 15 Subpart B compliant
The modular transmitter is only FCC authorized for FCC Part 15 Subpart C 15.247 & 15.209 and that the host
product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered
by the modular transmitter grant of certification. If the grantee markets their product as being Part 15 Subpart
B compliant (when it also contains unintentional-radiator digital circuity), then the grantee shall provide a notice
stating that the final host product still requires Part 15 Subpart B compliance testing with the modular transmitter
installed.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired opera-
tion.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This
device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.
The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all
persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
OEM Integration Instructions
This device is intended only for OEM integrators under the following conditions:
The transmitter module may not be co-located with any other transmitter or antenna.
The module shall be only used with the external antenna(s) that has been originally tested and certified with
this module.
As long as the conditions above are met, further transmitter test will not be required. However, the OEM integrator is
still responsible for testing their end-product for any additional compliance requirements required with this module
installed (for example, digital device emissions, PC peripheral requirements, etc.).
Espressif Systems 16 ESP32-C3-MINI-1U User Manual v0.1
3 U.S. FCC Statement
Validity of Using the Module Certification
In the event that these conditions cannot be met (for example certain laptop configurations or co-location with
another transmitter), then the FCC authorization for this module in combination with the host equipment is no
longer considered valid and the FCC ID of the module cannot be used on the final product. In these circumstances,
the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a
separate FCC authorization.
End Product Labeling
The final end product must be labeled in a visible area with the following: “Contains Transmitter Module FCC ID:
2AARRSF13569-1”.
Espressif Systems 17 ESP32-C3-MINI-1U User Manual v0.1
4 IC Statement
4 IC Statement
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two
conditions:
This device may not cause interference; and
This device must accept any interference, including interference that may cause undesired operation of the
device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes:
l’appareil ne doit pas produire de brouillage, et
l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est suscep-
tible d’en compromettre le fonctionnement.
Radiation Exposure Statement
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance 20 cm between the radiator and your body.
Déclaration d’exposition aux radiations:
Cet équipement est conforme aux limites d’exposition aux rayonnements ISED établies pour un environnement
non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source
de rayonnement et votre corps.
RSS247 Section 6.4 (5)
The device could automatically discontinue transmission in case of absence of information to transmit, or opera-
tional failure. Note that this is not intended to prohibit transmission of control or signaling information or the use of
repetitive codes where required by the technology.
L’appareil peut interrompre automatiquement la transmission en cas d’absence d’informations à transmettre ou
de panne opérationnelle. Notez que ceci n’est pas destiné à interdire la transmission d’informations de contrôle
ou de signalisation ou l’utilisation de codes répétitifs lorsque cela est requis par la technologie.
This device is intended only for OEM integrators under the following conditions (For module device use):
The antenna must be installed such that 20 cm is maintained between the antenna and users, and
The transmitter module may not be co-located with any other transmitter or antenna.
As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is
still responsible for testing their end-product for any additional compliance requirements required with this module
installed.
Espressif Systems 18 ESP32-C3-MINI-1U User Manual v0.1
4 IC Statement
Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes (Pour utilisa
tion de dispositif module):
L’antenne doit être installée de telle sorte qu’une distance de 20 cm est respectée entre l’antenne et les
utilisateurs, et
Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne.
Tant que les 2 conditions ci-dessus sont remplies, des essais supplémentaires sur l’émetteur ne seront pas néces-
saires. Toutefois, l’intégrateur OEM est toujours responsable des essais sur son produit final pour toutes exigences
de conformité supplémentaires requis pour ce module installé.
IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations or colocation with
another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on
the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate Canada authorization.
NOTE IMPORTANTE:
Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines configurations d’ordinateur
portable ou de certaines co-localisation avec un autre émetteur), l’autorisation du Canada n’est plus consid-
éré comme valide et l’ID IC ne peut pas être utilisé sur le produit final. Dans ces circonstances, l’intégrateur
OEM sera chargé de réévaluer le produit final (y compris l’émetteur) et l’obtention d’une autorisation distincte au
Canada.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm
may be maintained between the antenna and users. The final end product must be labeled in a visible area with
the following: “Contains IC: 21098-ESPC3MINII”.
Plaque signalétique du produit final
Ce module émetteur est autorisé uniquement pour une utilisation dans un dispositif où l’antenne peut être installée
de telle sorte qu’une distance de 20cm peut être maintenue entre l’antenne et les utilisateurs. Le produit final doit
être étiqueté dans un endroit visible avec l’inscription suivante: ”Contient des IC: 21098-ESPC3MINII”.
Manual Information to the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove
this RF module in the user’s manual of the end product which integrates this module. The end user manual shall
include all required regulatory information/warning as show in this manual.
Manuel d’information à l’utilisateur final
L’intégrateur OEM doit être conscient de ne pas fournir des informations à l’utilisateur final quant à la façon d’installer
ou de supprimer ce module RF dans le manuel de l’utilisateur du produit final qui intègre ce module. Le manuel
Espressif Systems 19 ESP32-C3-MINI-1U User Manual v0.1
4 IC Statement
de l’utilisateur final doit inclure toutes les informations réglementaires requises et avertissements comme indiqué
dans ce manuel.
Espressif Systems 20 ESP32-C3-MINI-1U User Manual v0.1
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23

Espressif ESP32­-C3­-Mini-1U General-Purpose Wi-Fi and Bluetooth LE Module Manuel utilisateur

Catégorie
Antennes réseau
Taper
Manuel utilisateur
Ce manuel convient également à