Sony MEX-M72BT Mode d'emploi

Marque: Sony

Modèle: MEX-M72BT

Catégorie: Récepteurs multimédia de voiture

Taper: Mode d'emploi

MEX-M72BT

4-739-026-12(1)

FM/AM

CD Bluetooth®

Marine Audio

Operating Instructions

Mode d’emploi

Manual de instrucciones

Owner’s Record

The model and serial numbers are located on the

bottom of the unit.

Record the serial number in the space provided below.

Refer to these numbers whenever you call upon your

Sony dealer regarding this product.

Model No. MEX-M72BT

Serial No.

To cancel the demonstration (DEMO) display, see

page 23.

To switch the FM/AM tuning step, see page 10.

For the connection/installation, see page 39.

Pour annuler l’affichage de démonstration (DEMO),

reportez-vous à la page 25.

Pour commuter l’intervalle de syntonisation FM/AM,

reportez-vous à la page 9.

Pour le raccordement/l’installation, reportez-vous à

la page 43.

Para cancelar la pantalla de demostración (DEMO),

consulte la página 24.

Para cambiar el paso de sintonización de FM/AM,

consulte la página 9.

Para la conexión/instalación, consulte la página 41.

2GB

This product is classified as a Class 1 Laser

product under IEC/EN 60825-1:2007 and IEC/

EN 60825-1:2014 and Class I Laser product

under 21 CFR Part 1040.10.

 Emission Duration: Continuous

 Laser Output: Less than 55.8 W

 Wavelength: 775 nm to 800 nm

The nameplate indicating operating voltage,

etc., is located on the bottom of the chassis.

Warning

For safety, be sure to install this unit in the

dashboard of the boat as the rear side of

the unit becomes hot during use.

For details, see “Connection/Installation”

(page 39).

FOR THE CUSTOMERS IN THE USA.

NOT APPLICABLE IN CANADA,

INCLUDING IN THE PROVINCE OF

QUEBEC.

POUR LES CLIENTS AUX ÉTATS-UNIS.

NON APPLICABLE AU CANADA, Y

COMPRIS LA PROVINCE DE QUÉBEC.

This equipment has been tested and

found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the

FCC Rules.

These limits are designed to provide

reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses, and can

radiate radio frequency energy and, if not

installed and used in accordance with the

instructions, may cause harmful

interference to radio communications.

However, there is no guarantee that

interference will not occur in a particular

installation. If this equipment does cause

harmful interference to radio or television

reception, which can be determined by

turning the equipment off and on, the

user is encouraged to try to correct the

interference by one or more of the

following measures:

– Reorient or relocate the receiving

antenna.

– Increase the separation between the

equipment and receiver.

– Connect the equipment into an outlet

on a circuit different from that to which

the receiver is connected.

– Consult the dealer or an experienced

radio/TV technician for help.

You are cautioned that any changes or

modifications not expressly approved in

this manual could void your authority to

operate this equipment.

3GB

This device complies with part 15 of FCC

Rules and Innovation, Science and Economic

Development Canada’s licence-exempt

RSS(s). Operation is subject to the following

two conditions:

(1) this device may not cause harmful

interference, and

(2) this device must accept any interference

received, including interference that may

cause undesired operation.

This transmitter must not be co-located or

operated in conjunction with any other

antenna or transmitter.

Under Industry Canada regulations, this

radio transmitter may only operate using an

antenna of a type and maximum (or lesser)

gain approved for the transmitter by

Industry Canada. To reduce potential radio

interference to other users, the antenna type

and its gain should be so chosen that the

equivalent isotropically radiated power

(e.i.r.p.) is not more than that necessary for

successful communication.

This equipment complies with FCC/ISED

radiation exposure limits set forth for an

uncontrolled environment and meets the

FCC radio frequency (RF) Exposure

Guidelines and RSS-102 of the ISED radio

frequency (RF) Exposure rules. This

equipment has very low levels of RF energy

that is deemed to comply without maximum

permissive exposure evaluation (MPE).

If you have any questions about this

product:

Visit: www.sony.com/support

Contact: Sony Customer Information Service

Center at 1-800-222-7669

Write: Sony Customer Information Service

Center 12451 Gateway Blvd., Fort Myers, FL

33913

Supplier’s Declaration of Conformity

Trade Name: SONY

Model: MEX-M72BT

Responsible Party: Sony Electronics Inc.

Address: 16535 Via Esprillo, San Diego, CA

92127 U.S.A.

Telephone Number: 858-942-2230

This device complies with part 15 of the FCC

rules. Operation is subject to the following

two conditions:

(1) This device may not cause harmful

interference, and

(2) this device must accept any interference

received,

including interference that may cause

undesired operation.

CAUTION

The use of optical instruments with this

product will increase eye hazard.

For the State of California, USA only

Perchlorate Material – special handling may

apply, See

www.dtsc.ca.gov/hazardouswaste/

perchlorate

Made in Thailand

The validity of the CE marking is restricted to

only those countries where it is legally

enforced, mainly in the countries EEA

(European Economic Area) and Switzerland.

Hereby, Sony Corporation declares that this

equipment is in compliance with Directive

2014/53/EU.

The full text of the EU declaration of

conformity is available at the following

internet address:

http://www.compliance.sony.de/

Notice for customers: the following

information is only applicable to

equipment sold in countries applying

EU Directives

This product has been manufactured by or

on behalf of Sony Corporation.

EU Importer: Sony Europe B.V.

Inquiries to the EU Importer or related to

product compliance in Europe should be

sent to the manufacturer’s authorized

representative, Sony Belgium, bijkantoor

van Sony Europe B.V., Da Vincilaan 7-D1, 1930

Zaventem, Belgium.

4GB

Disposal of waste batteries

and electrical and electronic

equipment (applicable in

the European Union and

other countries with

separate collection systems)

This symbol on the product, the battery or

on the packaging indicates that the product

and the battery shall not be treated as

household waste. On certain batteries this

symbol might be used in combination with a

chemical symbol. The chemical symbol for

lead (Pb) is added if the battery contains

more than 0.004% lead. By ensuring that

these products and batteries are disposed of

correctly, you will help to prevent potentially

negative consequences for the environment

and human health which could be caused by

inappropriate waste handling. The recycling

of the materials will help to conserve natural

resources. In case of products that for safety,

performance or data integrity reasons

require a permanent connection with an

incorporated battery, this battery should be

replaced by qualified service staff only. To

ensure that the battery and the electrical

and electronic equipment will be treated

properly, hand over these products at end-

of-life to the appropriate collection point for

the recycling of electrical and electronic

equipment. For all other batteries, please

view the section on how to remove the

battery from the product safely. Hand the

battery over to the appropriate collection

point for the recycling of waste batteries. For

more detailed information about recycling of

this product or battery, please contact your

local Civic Office, your household waste

disposal service or the shop where you

purchased the product or battery.

WARNING: Do not ingest

battery, Chemical Burn Hazard.

The remote commander contains a

coin/button cell battery. If the coin/button

cell battery is swallowed, it can cause severe

internal burns in just 2 hours and can lead to

death.

Keep new and used batteries away from

children. If the battery compartment does

not close securely, stop using the product

and keep it away from children.

If you think batteries might have been

swallowed or placed inside any part of the

body, seek immediate medical attention.

Note on the lithium battery

Do not expose the battery to excessive heat

such as direct sunlight, fire or the like.

CAUTION

The following frequency 1,606.5 – 1,710 kHz

range is not allocated to sound broadcasting

in the European Common Allocations table

and cannot be used in Europe.

Disclaimer regarding services offered

by third parties

Services offered by third parties may be

changed, suspended, or terminated without

prior notice. Sony does not bear any

responsibility in these sorts of situations.

Warning if your boat’s ignition has no

ACC position

Be sure to set the AUTO OFF function

(page 23). The unit will shut off

completely and automatically in the set

time after the unit is turned off and the

clock is displayed (i.e. press and hold OFF

for 1 second), which prevents battery

drain. If you do not set the AUTO OFF

function, press and hold OFF until the

display disappears each time you turn the

ignition off.

5GB

Caution

IN NO EVENT SHALL SONY BE LIABLE FOR

ANY INCIDENTAL, INDIRECT OR

CONSEQUENTIAL DAMAGES OR OTHER

DAMAGES INCLUDING, WITHOUT

LIMITATION, LOSS OF PROFITS, LOSS OF

REVENUE, LOSS OF DATA, LOSS OF USE OF

THE PRODUCT OR ANY ASSOCIATED

EQUIPMENT, DOWNTIME, AND PURCHASER’S

TIME RELATED TO OR ARISING OUT OF THE

USE OF THIS PRODUCT, ITS HARDWARE

AND/OR ITS SOFTWARE.

Dear customer, this product includes a radio

transmitter.

According to UNECE Regulation no. 10,

vessel manufacturers may impose specific

conditions for installation of radio

transmitters into boats. Please check your

boat’s operation manual or contact the

manufacturer or your boat dealer, before

you install this product.

Emergency calls

This BLUETOOTH boat handsfree and the

electronic device connected to the

handsfree operate using radio signals,

cellular, and landline networks as well as

user-programmed function, which cannot

guarantee connection under all conditions.

Therefore do not rely solely upon any

electronic device for essential

communications (such as medical

emergencies).

On BLUETOOTH communication

 Microwaves emitting from a BLUETOOTH

device may affect the operation of

electronic medical devices. Turn off this

unit and other BLUETOOTH devices in the

following locations, as it may cause an

accident.

– where inflammable gas is present, in a

hospital, train, airplane, or petrol station

– near automatic doors or a fire alarm

 This unit supports security capabilities that

comply with the BLUETOOTH standard to

provide a secure connection when the

BLUETOOTH wireless technology is used,

but security may not be enough

depending on the setting. Be careful when

communicating using BLUETOOTH wireless

technology.

 We do not take any responsibility for the

leakage of information during BLUETOOTH

communication.

If you have any questions or problems

concerning your unit that are not covered in

this manual, consult your nearest Sony

dealer.

Important notice

6GB

Table of Contents

Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Guide to Parts and Controls. . . . . . . . . . . . . 7

Getting Started

Detaching the Front Panel . . . . . . . . . . . . . . 9

Resetting the Unit. . . . . . . . . . . . . . . . . . . . 10

Switching the FM/AM Tuning Step . . . . . . 10

Setting the Clock. . . . . . . . . . . . . . . . . . . . . 10

Checking the Battery Voltage . . . . . . . . . . 10

Preparing a BLUETOOTH Device . . . . . . . . 10

Connecting a USB Device. . . . . . . . . . . . . . 13

Connecting Other Portable Audio

Device . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Listening to the Radio

Listening to the Radio . . . . . . . . . . . . . . . . 13

Using Radio Data System (RDS). . . . . . . . . 14

Listening to the SiriusXM Radio

(US/Canada only) . . . . . . . . . . . . . . . . . 14

Playback

Playing a Disc . . . . . . . . . . . . . . . . . . . . . . . 16

Playing a USB Device . . . . . . . . . . . . . . . . . 16

Playing a BLUETOOTH Device . . . . . . . . . . 16

Searching and Playing Tracks . . . . . . . . . . 17

Listening to Pandora®

Setting up Pandora®. . . . . . . . . . . . . . . . . . 18

Streaming Pandora® . . . . . . . . . . . . . . . . . . 18

Available Operations in Pandora®. . . . . . . 18

Handsfree Calling (via

BLUETOOTH only)

Receiving a Call. . . . . . . . . . . . . . . . . . . . . . 19

Making a Call. . . . . . . . . . . . . . . . . . . . . . . . 19

Available Operations During Call . . . . . . . 20

Useful Functions

“Sony | Music Center” with iPhone/

Android™ Smartphone . . . . . . . . . . . . 21

Using Voice Recognition (Android

Smartphone only). . . . . . . . . . . . . . . . . 22

Using “Siri Eyes Free” . . . . . . . . . . . . . . . . . 22

Settings

Canceling the DEMO Mode . . . . . . . . . . . . 23

Basic Setting Operation. . . . . . . . . . . . . . . 23

General Setup (GENERAL) . . . . . . . . . . . . . 23

Sound Setup (SOUND) . . . . . . . . . . . . . . . . 24

Display Setup (DISPLAY) . . . . . . . . . . . . . . 25

BLUETOOTH Setup (BLUETOOTH) . . . . . . . 25

“Sony | Music Center” Setup

(SONY APP). . . . . . . . . . . . . . . . . . . . . . 26

Additional Information

Updating the Firmware . . . . . . . . . . . . . . . 26

Precautions. . . . . . . . . . . . . . . . . . . . . . . . . 26

Maintenance. . . . . . . . . . . . . . . . . . . . . . . . 28

Specifications . . . . . . . . . . . . . . . . . . . . . . . 28

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . 31

Messages . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Connection/Installation

Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Parts List for Installation . . . . . . . . . . . . . . 39

Connection . . . . . . . . . . . . . . . . . . . . . . . . . 40

Installation . . . . . . . . . . . . . . . . . . . . . . . . . 42

7GB

Guide to Parts and Controls

 PTY (program type)

Select PTY in RDS.

(browse) (page 15, 17, 18)

Enter the browse mode during playback.

(Not available when a USB device in

Android mode or iPod is connected.)

 Front panel release button

 SRC (source)

Turn on the power.

Change the source.

OFF

Press and hold for 1 second to turn the

source off and display the clock.

Press and hold for more than 2 seconds

to turn off the power and the display.

If the unit is turned off and the display

disappears, operation by the remote

commander is not available.

 Control dial

Rotate to adjust the volume.

PUSH ENTER

Enter the selected item.

Press SRC, rotate then press to change

the source (timeout in 2 seconds).

Open the setup menu.

VOICE (page 20, 22)

Press and hold for more than 2 seconds

to activate voice dial, voice recognition

(Android smartphone only), or the Siri

function (iPhone only).

N-Mark

Touch the control dial with Android

smartphone to make BLUETOOTH

connection.

 Disc slot

 Display window

 USB port

 (disc eject)

 / (SEEK –/+)

Tune in radio stations automatically.

Press and hold to tune manually.

/ (prev/next)

/ (fast-reverse/fast-forward)

 (back)

Return to the previous display.

MODE (page 13)

 CALL

Enter the call menu. Receive/end a call.

Press and hold for more than 2 seconds

to switch the BLUETOOTH signal.

 Receptor for the remote commander

Main unit

8GB

 Number buttons (1 to 6)

Receive stored radio stations. Press and

hold to store stations.

ALBUM /

Skip an album for audio device. Press and

hold to skip albums continuously.

(Not available when a USB device in

Android mode or iPod is connected.)

Press  to thumbs up, or  to thumbs

down in Pandora® (page 18).

(repeat)

(Not available when a USB device in

Android mode is connected.)

(shuffle)

(Not available when a USB device in

Android mode is connected.)

MIC (page 20)

 (play/pause)

 EXTRA BASS

Reinforces bass sound in synchronization

with the volume level. Press to change

the EXTRA BASS setting: [1], [2], [OFF].

 AUX input jack

 DSPL (display)

Press to change display items.

SCRL (scroll)

Press and hold to scroll a display item.

The VOL (volume) + button has a tactile dot.

 SOUND

Open the SOUND menu directly.

Press and hold to open the setup menu.

///

Select a setup item, etc.

ENTER

Enter the selected item.

Press and hold for more than 2 seconds

to establish or terminate the “Sony |

Music Center” function.

/ (prev/next)

+/– (album +/–)

 VOL (volume) +/–

Remove the insulation film before use.

RM-X232 Remote commander

9GB

 VOL (volume) +/–

 GP (group)/ALBM (album) +/–

Receive stored stations.

Detaching the Front Panel

You can detach the front panel of this unit to

prevent theft.

1 Press and hold OFF  until the unit

turns off, press the front panel

release button , then pull the panel

towards you to remove.

Caution alarm

If you turn the ignition switch to the OFF

position without detaching the front panel,

the caution alarm will sound for a few

seconds. The alarm will only sound if the

built-in amplifier is used.

Serial numbers

Make sure the serial numbers on the bottom

of the unit and the back of the front panel

are matched correctly. Otherwise you cannot

make BLUETOOTH pairing, connection and

disconnection by NFC.

RM-X11M Marine remote

commander (not supplied)

Getting Started

Attaching the front panel

10GB

Resetting the Unit

Before operating the unit for the first time,

after replacing the boat battery, or changing

the connections, you must reset the unit.

1 Press DSPL and CALL for more than

2seconds.

Note

Resetting the unit will erase the clock setting and

some stored contents.

Switching the FM/AM

Tuning Step

Set the FM/AM tuning step of your country.

This setting appears only while the source

is off and the clock is displayed.

1 Press MENU, rotate the control dial to

select [GENERAL], then press it.

2 Rotate the control dial to select [SET

TUNER-STP], then press it.

3 Rotate the control dial to select from

[SET 50K/9K], [SET 100K/10K] or [SET

200K/10K], then press it.

Setting the Clock

1 Press MENU, rotate the control dial to

select [GENERAL], then press it.

2 Rotate the control dial to select [SET

CLOCK], then press it.

3 Rotate the control dial to select

[MANUAL], then press it.

The hour indication flashes.

4 Rotate the control dial to set the hour

and minute.

To move the digital indication, press

/ (SEEK –/+).

5 After setting the minute, press MENU.

The setup is complete and the clock

starts.

To display the clock

Press DSPL.

To set the clock automatically

Select [AUTO <RDS>] in step 3.

Checking the Battery

Voltage

You can check the current battery voltage.

(Not available while the source is off and the

clock is displayed.)

1 Press DSPL repeatedly until the

battery voltage display appears.

Preparing a BLUETOOTH

Device

You can enjoy music, or perform handsfree

calling depending on the BLUETOOTH

compatible device such as a smartphone,

cellular phone and audio device (hereafter

“BLUETOOTH device” if not otherwise

specified). For details on connecting, refer to

the operating instructions supplied with the

device.

Before connecting the device, turn down the

volume of this unit; otherwise, loud sound

may result.

By touching the control dial on the unit with

an NFC* compatible smartphone, the unit is

paired and connected with the smartphone

automatically.

* NFC (Near Field Communication) is a technology

enabling short-range wireless communication

between various devices, such as mobile phones

and IC tags. Thanks to the NFC function, data

communication can be achieved easily just by

touching the relevant symbol or designated

location on NFC compatible devices.

For a smartphone with Android OS 4.0 or

lower installed, downloading the app “NFC

Easy Connect” available on Google Play is

required. The app may not be downloadable

in some countries/regions.

Connecting with a Smartphone

using One-touch connection (NFC)

11GB

1 Activate the NFC function on the

smartphone.

For details, refer to the operating

instructions supplied with the

smartphone.

2 Touch the N-Mark part of the unit

with the N-Mark part of the

smartphone.

Make sure that lights up on the display

of the unit.

To disconnect using NFC

Touch the N-Mark part of the unit with the

N-Mark part of the smartphone again.

Notes

• When making the connection, handle the

smartphone carefully to prevent scratches.

• One-touch connection is not possible when the

unit is already connected to two NFC compatible

devices. In this case, disconnect either device, and

make connection with the smartphone again.

When connecting a BLUETOOTH device for

the first time, mutual registration (called

“pairing”) is required. Pairing enables this

unit and other devices to recognize each

other. This unit can connect two BLUETOOTH

devices (two cellular phones, or a cellular

phone and an audio device).

1 Place the BLUETOOTH device within

1 m (3 ft) of this unit.

2 Press MENU, rotate the control dial to

select [BLUETOOTH], then press it.

3 Rotate the control dial to select [SET

PAIRING], then press it.

4 Rotate the control dial to select [SET

DEVICE 1]* or [SET DEVICE 2]*, then

press it.

flashes while the unit is in pairing

standby mode.

* [SET DEVICE 1] or [SET DEVICE 2] will be

changed to the paired device name after

pairing is complete.

5 Perform pairing on the BLUETOOTH

device so it detects this unit.

6 Select [MEX-M72BT] shown in the

display of the BLUETOOTH device.

If your model name does not appear,

repeat from step 2.

7 If passkey* input is required on the

BLUETOOTH device, input [0000].

* Passkey may be called “Passcode,” “PIN code,”

“PIN number” or “Password,” etc., depending

on the device.

When pairing is made, stays lit.

8 Select this unit on the BLUETOOTH

device to establish the BLUETOOTH

connection.

or lights up when the connection is

made.

Note

While connecting to a BLUETOOTH device, this unit

cannot be detected from another device. To enable

detection, enter the pairing mode and search for

this unit from another device.

To start playback

For details, see “Playing a BLUETOOTH

Device” (page 16).

Pairing and connecting with a

BLUETOOTH device

MEX-M72BT

[0000]

Input passkey

12GB

To disconnect the paired device

Perform steps 2 to 4 to disconnect after this

unit and the BLUETOOTH device are paired.

To use a paired device, connection with this

unit is required. Some paired devices will

connect automatically.

1 Press MENU, rotate the control dial to

select [BLUETOOTH], then press it.

2 Rotate the control dial to select [SET

BT SIGNL], then press it.

Make sure that lights up.

3 Activate the BLUETOOTH function on

the BLUETOOTH device.

4 Operate the BLUETOOTH device to

connect to this unit.

or lights up.

Icons in the display:

To connect the last-connected device

from this unit

Activate the BLUETOOTH function on the

BLUETOOTH device.

To connect with the audio device, press SRC

to select [BT AUDIO] and press  (play/

pause).

To connect with the cellular phone, press

CALL.

Note

While streaming BLUETOOTH audio, you cannot

connect from this unit to the cellular phone.

Connect from the cellular phone to this unit instead.

Tip

With BLUETOOTH signal on: when the ignition is

turned to on, this unit reconnects automatically to

the last-connected cellular phone.

To install the microphone

For details, see “Installing the microphone”

(page 42).

When an iPhone/iPod with iOS5 or later

installed is connected to the USB port, the

unit is paired and connected with the

iPhone/iPod automatically.

To enable BLUETOOTH Auto Pairing, make

sure [SET AUTOPAIR] in [BLUETOOTH] is set

to [ON] (page 25).

1 Activate the BLUETOOTH function on

the iPhone/iPod.

2 Connect an iPhone/iPod to the USB

port.

Make sure that lights up on the display

of the unit.

Notes

• BLUETOOTH Auto Pairing is not possible if the unit

is already connected to two BLUETOOTH devices.

In this case, disconnect either device, then

connect the iPhone/iPod again.

• If BLUETOOTH Auto Pairing is not established, see

“Preparing a BLUETOOTH Device” (page 10).

Connecting with a paired

BLUETOOTH device

Lights up when handsfree calling is

available by enabling the HFP

(Handsfree Profile).

Lights up when the audio device is

playable by enabling the A2DP

(Advanced Audio Distribution

Profile).

Connecting with an iPhone/iPod

(BLUETOOTH Auto Pairing)

13GB

Connecting a USB Device

1 Turn down the volume on the unit.

2 Connect the USB device to the unit.

To connect an iPod/iPhone, use the USB

connection cable for iPod (not supplied).

Connecting Other Portable

Audio Device

1 Turn off the portable audio device.

2 Turn down the volume on the unit.

3 Connect the portable audio device to

the AUX input jack (stereo mini jack)

on the unit with a connecting cord

(not supplied)*.

* Be sure to use a straight type plug.

4 Press SRC to select [AUX].

To match the volume level of the

connected device to other sources

Start playback of the portable audio device

at a moderate volume, and set your usual

listening volume on the unit.

Press MENU, then select [SOUND]  [SET AUX

VOL] (page 24).

Listening to the Radio

Tuning step setting is required (page 10).

To listen to the radio, press SRC to select

[TUNER].

1 Press MODE to change the band (FM1,

FM2, FM3, AM1 or AM2).

2 Press MENU, rotate the control dial to

select [GENERAL], then press it.

3 Rotate the control dial to select [SET

BTM], then press it.

The unit stores stations in order of

frequency on the number buttons.

1 Press MODE to change the band (FM1,

FM2, FM3, AM1 or AM2).

2 Perform tuning.

To tune manually

Press and hold / (SEEK –/+) to

locate the approximate frequency, then

press / (SEEK –/+) repeatedly to

finely adjust to the desired frequency.

To tune automatically

Press / (SEEK –/+).

Scanning stops when the unit receives a

station.

1 While receiving the station that you

want to store, press and hold a

number button (1 to 6) until [MEM]

appears.

1 Select the band, then press a number

button (1 to 6).

Listening to the Radio

Storing automatically (BTM)

Tuning

Storing manually

Receiving the stored stations

14GB

Using Radio Data System

(RDS)

1 Press PTY during FM reception.

2 Rotate the control dial until the

desired program type appears, then

press it.

The unit starts to search for a station

broadcasting the selected program type.

Type of programs (tuner step: 200 kHz/

10 kHz)

Type of programs (tuner step: 100 kHz/

10 kHz, 50 kHz/9 kHz)

Listening to the SiriusXM

Radio (US/Canada only)

Only SiriusXM brings you more of what you

love to listen to, all in one place. Get over

140 channels, including commercial-free

music plus the best sports, news, talk,

comedy and entertainment. Welcome to the

world of satellite radio. A SiriusXM Connect

Vehicle Tuner and Subscription are required.

For more information, visit

www.siriusxm.com

After installing your SiriusXM Connect

Vehicle Tuner and antenna, press SRC to

select [SIRIUSXM]. You should be able to

hear the SiriusXM preview channel on

Channel 1. After verifying that you can hear

the preview channel, select Channel 0 to

find the Radio ID of your tuner. In addition,

the Radio ID is located on the bottom of the

SiriusXM Connect Vehicle Tuner and its

packaging. You will need this number to

activate your subscription. Write the number

down for reference.

Note

The SiriusXM Radio ID does not include the letters I,

O, S or F.

In the USA, you can activate online or by

calling SiriusXM Listener Care:

•Online: Visit www.siriusxm.com/

activatenow

•Phone: Call 1-866-635-2349

In Canada, you can activate online or by

calling SiriusXM Listener Care:

• Online: Visit www.siriusxm.ca/activatexm

•Phone: Call 1-877-438-9677

As part of the activation process, the

SiriusXM satellites will send an activation

message to your tuner. When your radio

detects that the tuner has received the

activation message, your radio will display:

[SUBSCRIPTION UPDATED - PRESS ENT TO

CONTINUE]. Once subscribed, you can tune

to channels in your subscription plan.

Selecting program types (PTY)

NEWS (News), INFORM (Information), SPORTS

(Sports), TALK (Talk), ROCK (Rock), CLS ROCK

(Classic Rock), ADLT HIT (Adult Hits), SOFT RCK

(Soft Rock), TOP 40 (Top 40), COUNTRY

(Country), OLDIES (Oldies), SOFT (Soft),

NOSTALGA (Nostalgia), JAZZ (Jazz), CLASSICL

(Classical), R & B (Rhythm and Blues), SOFT R&B

(Soft Rhythm and Blues), LANGUAGE (Foreign

Language), REL MUSC (Religious Music), REL

TALK (Religious Talk), PERSNLTY (Personality),

PUBLIC (Public), COLLEGE (College), HABL ESP

(Spanish Talk), MUSC ESP (Spanish Music), HIP

HOP (Hip-Hop), WEATHER (Weather)

NEWS (News), AFFAIRS (Current Affairs), INFO

(Information), SPORT (Sports), EDUCATE

(Education), DRAMA (Drama), CULTURE

(Culture), SCIENCE (Science), VARIED (Varied),

POP M (Pop Music), ROCK M (Rock Music),

EASY M (Easy Listening), LIGHT M (Light

classical), CLASSICS (Serious classical), OTHER

M (Other Music), WEATHER (Weather),

FINANCE

ance), CHILDREN (Children’s program),

SOCIAL (Social Affairs), RELIGION (Religion),

PHONE IN (Phone In), TRAVEL (Travel), LEISURE

(Leisure), JAZZ (Jazz Music), COUNTRY (Country

Music), NATION M (National Music), OLDIES

(Oldies Music), FOLK M (Folk Music),

DOCUMENT (Documentary)

Activating your SiriusXM

Subscription

15GB

Notes

• The activation process usually takes 10 to 15

minutes, but may take up to an hour.

• Your radio will need to be turned on and receiving

the SiriusXM signal to receive the activation

message.

1 Press (browse).

2 Rotate the control dial to select

[CHANNEL], then press it.

3 Rotate the control dial to select the

desired channel, then press it.

To select channels with rapid browse

mode

Press and hold  or  of remote

commander more than 2 seconds after

[CHANNEL] selected, then press ENTER.

To select channels from categories

Press (browse).

2 Rotate the control dial to select [CATEGORY],

then press it.

3 Rotate the control dial to select the desired

category, then press it.

The channel list appears.

4 Rotate the control dial to select the desired

channel, then press it.

To store channels

While receiving the channel that you want to

store, press and hold a number button (1 to

6) until [MEM] appears.

To receive the stored channel, press MODE

to select the Band you want ([SX1], [SX2] or

[SX3]), then press a number button (1 to 6).

(Each Band can store up to 6 channels.)

To set a parental control

The parental control feature allows you to

limit access to SiriusXM channels with

mature content. When enabled, the parental

control feature requires you to enter a

passcode to tune to the locked channels.

Information on setting up the passcode and

locking channels can be found below.

1 Press MENU and rotate the control dial.

2 Select [GENERAL]  [SXM PARENTAL] 

[LOCK SELECT]  [LOCK-ON].

3 Enter the passcode by rotating the control

dial on the unit or pressing / on the

remote commander.

To move the entry position, press /

(SEEK –/+) on the unit or / on the remote

commander.

The initial passcode is [0000].

4 After entering the passcode, press ENTER.

To unlock the channels, select [LOCK-OFF].

To change the passcode

Press MENU and rotate the control dial.

2 Select [GENERAL]  [SXM PARENTAL] 

[CODE EDIT].

3 Enter the current passcode on the current

passcode input display, then press ENTER.

The initial passcode is [0000].

4 Enter your new 4-digit passcode on the new

passcode input display, then press ENTER.

To change display items

Press DSPL to change as follows:

Channel Number (Default)  Channel Name

 Artist Name  Song Title  Content Info 

Category Name  Clock  Battery Voltage

Selecting channels for SiriusXM

16GB

Playing a Disc

1 Insert the disc (label side up).

Playback starts automatically.

Playing a USB Device

In these Operating Instructions, “iPod” is

used as a general reference for the iPod

functions on an iPod and iPhone, unless

otherwise specified by the text or

illustrations.

For details on the compatibility of your iPod,

see “About iPod” (page 27) or visit the

support site on the back cover.

AOA (Android Open Accessory) 2.0, MSC

(Mass Storage Class) and MTP (Media

Transfer Protocol) type USB devices*

compliant with the USB standard can be

used. Depending on the USB device, the

Android mode or MSC/MTP mode can be

selected on the unit.

Some digital media players or Android

smartphones may require setting to MTP

mode.

* e.g., a USB flash drive, digital media player,

Android smartphone

Notes

• For details on the compatibility of your USB device,

visit the support site on the back cover.

• Smartphones with Android OS 4.1 or higher

installed support Android Open Accessory 2.0

(AOA 2.0). However, some smartphones may not

fully support AOA 2.0 even if Android OS 4.1 or

higher is installed.

For details on the compatibility of your Android

smartphone, visit the support site on the back

cover.

• Playback of the following files is not supported.

MP3/WMA/AAC/FLAC:

– copyright-protected files

– DRM (Digital Rights Management) files

– Multi-channel audio files

MP3/WMA/AAC:

– lossless compression files

Before making a connection, select the USB

mode (Android mode or MSC/MTP mode)

depending on the USB device (page 23).

1 Connect a USB device to the USB port

(page 13).

Playback starts.

If a device is already connected, to start

playback, press SRC to select [USB] ([IPD]

appears in the display when the iPod is

recognized).

2 Adjust the volume on this unit.

To stop playback

Press and hold OFF for 1 second.

To remove the device

Stop playback, then remove the device.

Caution for iPhone

When you connect an iPhone via USB,

phone call volume is controlled by the

iPhone, not the unit. Do not inadvertently

increase the volume on the unit during a

call, as a sudden loud sound may result

when the call ends.

Playing a BLUETOOTH Device

You can play contents on a connected

device that supports BLUETOOTH A2DP

(Advanced Audio Distribution Profile).

1 Make BLUETOOTH connection with

the audio device (page 10).

To select the audio device, press MENU,

then select [BLUETOOTH]  [SET

AUDIODEV] (page 25).

2 Press SRC to select [BT AUDIO].

3 Operate the audio device to start

playback.

Playback

17GB

4 Adjust the volume on this unit.

Notes

• Depending on the audio device, information such

as title, track number/time and playback status

may not be displayed on this unit.

• Even if the source is changed on this unit,

playback of the audio device does not stop.

• [BT AUDIO] does not appear in the display while

running the “Sony | Music Center” application via

the BLUETOOTH function.

To match the volume level of the

BLUETOOTH device to other sources

Start playback of the BLUETOOTH audio

device at a moderate volume, and set your

usual listening volume on the unit.

Press MENU, then select [SOUND]  [SET BTA

VOL] (page 24).

Searching and Playing

Tracks

Not available when a USB device in Android

mode is connected.

1 During playback, press (repeat) or

(shuffle) repeatedly to select the

desired play mode.

Playback in the selected play mode may

take time to start.

Available play modes differ depending on

the selected sound source.

Not available when a USB device in Android

mode or iPod is connected.

1 During CD or USB playback, press

(browse)* to display the list of search

categories.

When the track list appears, press

(back) repeatedly to display the desired

search category.

* During USB playback, press (browse) for

more than 2 seconds to directly return to the

beginning of the category list.

2 Rotate the control dial to select the

desired search category, then press it

to confirm.

3 Repeat step 2 to search the desired

track.

Playback starts.

To exit the “Quick-BrowZer” mode

Press (browse).

Not available when a USB device in Android

mode or iPod is connected.

1 During CD or USB playback, press

(browse).

2 Press  (SEEK +).

3 Rotate the control dial to select the

item.

The list is jumped in steps of 10% of the

total number of items.

4 Press ENTER to return to the “Quick-

BrowZer” mode.

The selected item appears.

5 Rotate the control dial to select the

desired item, then press it.

Playback starts.

Repeat play and shuffle play

Searching a track by name

(“Quick-BrowZer™”)

Searching by skipping items

(Jump mode)

18GB

Pandora® is available to stream music

through your iPhone. You can control

Pandora® on a BLUETOOTH connected

iPhone/Android smartphone from this unit.

Pandora® is only available in certain

countries. Please visit

http://www.pandora.com/legal

for more information.

Setting up Pandora®

1 Check the compatibility of your

mobile device by visiting the support

site on the back cover.

2 Download the latest version of the

Pandora® application from your

smartphone’s app store. A list of

compatible devices can be found at

www.pandora.com/everywhere/

mobile

Streaming Pandora®

1 Make BLUETOOTH connection with

the audio device (page 10).

To select the audio device, press MENU,

then select [BLUETOOTH]  [AUDIODEV]

(page 25).

2 Press SRC to select [PANDORA].

3 Launch Pandora® application on your

mobile device.

4 Press  (play/pause) to start

playback.

If the device number appears

Make sure that the same numbers are

displayed (e.g., 123456) in this unit and the

mobile device, then press ENTER on this unit

and select [Yes] on the mobile device.

When activating the BLUETOOTH

function

You can adjust the volume level.

Press MENU, then select [SOUND]  [SET BTA

VOL] (page 24).

Available Operations in

Pandora®

“Thumbs Up” or “Thumbs Down” feedback

allows you to personalize stations.

1 During playback, press  (Thumbs

Up) or  (Thumbs Down).

The station list allows you to easily select a

desired station.

1 During playback, press (browse).

2 Press  (SEEK +) to select the

sorting order [BY DATE] or [A TO Z].

3 Rotate the control dial to select the

desired station, then press it.

Playback starts.

The track currently being played can be

bookmarked and stored in your Pandora®

account.

1 During playback, press MODE.

Listening to Pandora®

“Thumbs” feedback

Using the station list

Bookmarking

19GB

To use a cellular phone, connect it with this

unit. You can connect two cellular phones to

the unit. For details, see “Preparing a

BLUETOOTH Device” (page 10).

Receiving a Call

1 Press CALL when a call is received

with a ringtone.

The phone call starts.

Note

The ringtone and talker’s voice are output from the

front speakers. To select the speakers for handsfree

calling, press MENU, then select [BLUETOOTH] 

[SET VOICE-OUT] (page 26).

To reject the call

Press and hold OFF for 1 second.

To end the call

Press CALL again.

Making a Call

You can make a call from the phonebook or

call history when a cellular phone

supporting PBAP (Phone Book Access

Profile) is connected.

When two cellular phones are connected to

the unit, select either phone.

1 Press CALL.

When two cellular phones are connected

to the unit, rotate the control dial to

select either phone, then press it.

2 Rotate the control dial to select

[PHONE BOOK], then press it.

3 Rotate the control dial to select an

initial from the initial list, then press

it.

4 Rotate the control dial to select a

name from the name list, then press

it.

5 Rotate the control dial to select a

number from the number list, then

press it.

The phone call starts.

1 Press CALL.

When two cellular phones are connected

to the unit, rotate the control dial to

select either phone, then press it.

2 Rotate the control dial to select

[RECENT CALL], then press it.

A list of the call history appears.

3 Rotate the control dial to select a

name or phone number from the call

history, then press it.

The phone call starts.

1 Press CALL.

When two cellular phones are connected

to the unit, rotate the control dial to

select either phone, then press it.

2 Rotate the control dial to select [DIAL

NUMBER], then press it.

3 Rotate the control dial to enter the

phone number, and lastly select [ ]

(space), then press ENTER*.

The phone call starts.

* To move the digital indication, press /

(SEEK –/+).

Note

[_] appears instead of [#] on the display.

Handsfree Calling (via

BLUETOOTH only)

From the phonebook

From the call history

By phone number input

20GB

1 Press CALL.

When two cellular phones are connected

to the unit, rotate the control dial to

select either phone, then press it.

2 Rotate the control dial to select

[REDIAL], then press it.

The phone call starts.

You can make a call by saying the voice tag

stored in a connected cellular phone that

has a voice dialing function.

1 Press CALL.

When two cellular phones are connected

to the unit, rotate the control dial to

select either phone, then press it.

2 Rotate the control dial to select

[VOICE DIAL], then press it.

Alternatively, press and hold VOICE for

more than 2 seconds.

3 Say the voice tag stored on the

cellular phone.

Your voice is recognized, and the call is

made.

To cancel voice dialing

Press VOICE.

Available Operations During

Call

To adjust the ringtone volume

Rotate the control dial while receiving a call.

To adjust the talker’s voice volume

Rotate the control dial during a call.

To adjust the volume for the other party

(Mic gain adjustment)

Press MIC.

Adjustable volume levels: [MIC-LOW], [MIC-

MID], [MIC-HI].

To reduce echo and noise (Echo

Canceler/Noise Canceler Mode)

Press and hold MIC.

Settable mode: [EC/NC-1], [EC/NC-2].

To switch between handsfree mode

and handheld mode

During a call, press MODE to switch the

phone call audio between the unit and

cellular phone.

Note

Depending on the cellular phone, this operation

may not be available.

By redial

By voice tags

La page charge ...

Sony MEX-M72BT Mode d'emploi

Marque: Sony

Modèle: MEX-M72BT

Catégorie: Récepteurs multimédia de voiture

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Sony MEX-M72BT Operating instructions
español: Sony MEX-M72BT Instrucciones de operación

Sony MEX-M72BT Mode d'emploi

Sony MEX-M72BT Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents