Sony MEX-N5300BT Le manuel du propriétaire

4-738-937-31(1)

MEX-N5300BT/MEX-N4300BT

FM/MW/LW

CD Bluetooth®

Car Audio

Operating Instructions

GB

Bedienungsanleitung

DE

Mode d’emploi

FR

Istruzioni per l’uso

IT

Manual de

instrucciones

ES

To cancel the demonstration (DEMO) display, see

page 18.

For the connection/installation, see page 33.

Zum Deaktivieren der Demo-Anzeige (DEMO)

schlagen Sie bitte auf Seite 23 nach.

Informationen zum Anschluss und zur Installation

finden Sie auf Seite 39.

Pour annuler la démonstration (DEMO), reportez-

vous à la page 22.

Pour le raccordement/l’installation, reportez-vous à

la page 38.

Per annullare la dimostrazione (DEMO), vedere

pagina 22.

Per l’installazione e i collegamenti, consultare

pagina 38.

Para cancelar la pantalla de demostración (DEMO),

consulte la página 22.

Para la conexión/instalación, consulte la página 38.

2GB

Made in Thailand

This product is classified as a Class 1 Laser

product under IEC/EN 60825-1:2007 and IEC/

EN 60825-1:2014.

 Emission Duration: Continuous

 Laser Output: Less than 55.8 W

 Wavelength: 775 nm to 800 nm

The nameplate indicating operating voltage,

etc., is located on the bottom of the chassis.

The validity of the CE marking is restricted to

only those countries where it is legally

enforced, mainly in the countries EEA

(European Economic Area) and Switzerland.

Hereby, Sony Corporation declares that this

equipment is in compliance with Directive

2014/53/EU.

The full text of the EU declaration of

conformity is available at the following

internet address:

http://www.compliance.sony.de/

Notice for customers: the following

information is only applicable to

equipment sold in countries applying

EU Directives

This product has been manufactured by or

on behalf of Sony Corporation.

EU Importer: Sony Europe Limited.

Inquiries to the EU Importer or related to

product compliance in Europe should be

sent to the manufacturer’s authorized

representative, Sony Belgium, bijkantoor

van Sony Europe Limited, Da Vincilaan 7-D1,

1935 Zaventem, Belgium.

Disposal of waste batteries

and electrical and electronic

equipment (applicable in

the European Union and

other countries with

separate collection systems)

This symbol on the product, the battery or

on the packaging indicates that the product

and the battery shall not be treated as

household waste. On certain batteries this

symbol might be used in combination with a

chemical symbol. The chemical symbol for

lead (Pb) is added if the battery contains

more than 0.004% lead. By ensuring that

these products and batteries are disposed of

correctly, you will help to prevent potentially

negative consequences for the environment

and human health which could be caused by

inappropriate waste handling. The recycling

of the materials will help to conserve natural

resources. In case of products that for safety,

performance or data integrity reasons

require a permanent connection with an

incorporated battery, this battery should be

replaced by qualified service staff only. To

ensure that the battery and the electrical

and electronic equipment will be treated

properly, hand over these products at end-

of-life to the appropriate collection point for

the recycling of electrical and electronic

equipment. For all other batteries, please

view the section on how to remove the

battery from the product safely. Hand the

battery over to the appropriate collection

point for the recycling of waste batteries. For

more detailed information about recycling of

this product or battery, please contact your

local Civic Office, your household waste

disposal service or the shop where you

purchased the product or battery.

CAUTION

The following frequency 65 – 74 MHz range

is not allocated to sound broadcasting in the

European Common Allocations table and

cannot be used in Europe.

For safety, be sure to install this unit in the

dashboard of the car as the rear side of

the unit becomes hot during use.

For details, see “Connection/Installation”

(page 33).

3GB

Disclaimer regarding services offered

by third parties

Services offered by third parties may be

changed, suspended, or terminated without

prior notice. Sony does not bear any

responsibility in these sorts of situations.

About the NFC function

The model supporting the NFC function

described in this manual is as follows:

–MEX-N5300BT

Caution

IN NO EVENT SHALL SONY BE LIABLE FOR

ANY INCIDENTAL, INDIRECT OR

CONSEQUENTIAL DAMAGES OR OTHER

DAMAGES INCLUDING, WITHOUT

LIMITATION, LOSS OF PROFITS, LOSS OF

REVENUE, LOSS OF DATA, LOSS OF USE OF

THE PRODUCT OR ANY ASSOCIATED

EQUIPMENT, DOWNTIME, AND PURCHASER’S

TIME RELATED TO OR ARISING OUT OF THE

USE OF THIS PRODUCT, ITS HARDWARE

AND/OR ITS SOFTWARE.

Dear customer, this product includes a radio

transmitter.

According to UNECE Regulation no. 10, a

vehicle manufacturers may impose specific

conditions for installation of radio

transmitters into vehicles.

Please check your vehicle operation manual

or contact the manufacturer of your vehicle

or your vehicle dealer, before you install this

product into your vehicle.

Emergency calls

This BLUETOOTH car handsfree and the

electronic device connected to the

handsfree operate using radio signals,

cellular, and landline networks as well as

user-programmed function, which cannot

guarantee connection under all conditions.

Therefore do not rely solely upon any

electronic device for essential

communications (such as medical

emergencies).

On BLUETOOTH communication

 Microwaves emitting from a BLUETOOTH

device may affect the operation of

electronic medical devices. Turn off this

unit and other BLUETOOTH devices in the

following locations, as it may cause an

accident.

– where inflammable gas is present, in a

hospital, train, airplane, or petrol station

– near automatic doors or a fire alarm

 This unit supports security capabilities that

comply with the BLUETOOTH standard to

provide a secure connection when the

BLUETOOTH wireless technology is used,

but security may not be enough

depending on the setting. Be careful when

communicating using BLUETOOTH wireless

technology.

 We do not take any responsibility for the

leakage of information during BLUETOOTH

communication.

If you have any questions or problems

concerning your unit that are not covered in

this manual, consult your nearest Sony

dealer.

Warning if your car’s ignition has no

ACC position

Be sure to set the AUTO OFF function

(page 19). The unit will shut off completely

and automatically in the set time after the

unit is turned off and the clock is

displayed (i.e. press and hold OFF for 1

second), which prevents battery drain. If

you do not set the AUTO OFF function,

press and hold OFF until the display

disappears each time you turn the

ignition off.

Important notice

4GB

Table of Contents

Guide to Parts and Controls. . . . . . . . . . . . . 5

Getting Started

Detaching the Front Panel . . . . . . . . . . . . . . 7

Resetting the Unit. . . . . . . . . . . . . . . . . . . . . 7

Setting the Clock. . . . . . . . . . . . . . . . . . . . . . 7

Checking the Battery Voltage . . . . . . . . . . . 8

Preparing a BLUETOOTH Device . . . . . . . . . 8

Connecting a USB Device. . . . . . . . . . . . . . 10

Connecting Other Portable Audio

Device . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Listening to the Radio

Listening to the Radio . . . . . . . . . . . . . . . . . 11

Using Radio Data System (RDS). . . . . . . . . . 11

Playback

Playing a Disc . . . . . . . . . . . . . . . . . . . . . . . 12

Playing a USB Device . . . . . . . . . . . . . . . . . 12

Playing a BLUETOOTH Device . . . . . . . . . . 13

Searching and Playing Tracks . . . . . . . . . . 13

Handsfree Calling (via

BLUETOOTH only)

Receiving a Call. . . . . . . . . . . . . . . . . . . . . . 14

Making a Call. . . . . . . . . . . . . . . . . . . . . . . . 14

Available Operations During Call . . . . . . . 15

Useful Functions

“Sony | Music Center” with iPhone/

Android™ Smartphone . . . . . . . . . . . . 16

Using Voice Recognition (Android

Smartphone only). . . . . . . . . . . . . . . . . 17

Using “Siri Eyes Free” . . . . . . . . . . . . . . . . . 17

Settings

Canceling the DEMO Mode . . . . . . . . . . . . 18

Basic Setting Operation. . . . . . . . . . . . . . . 18

General Setup (GENERAL) . . . . . . . . . . . . . 19

Sound Setup (SOUND) . . . . . . . . . . . . . . . . 20

Display Setup (DISPLAY) . . . . . . . . . . . . . . 20

BLUETOOTH Setup (BLUETOOTH) . . . . . . . . 21

“Sony | Music Center” Setup

(SONY APP) . . . . . . . . . . . . . . . . . . . . . . 22

Additional Information

Updating the Firmware . . . . . . . . . . . . . . . 22

Precautions. . . . . . . . . . . . . . . . . . . . . . . . . 22

Maintenance. . . . . . . . . . . . . . . . . . . . . . . . 24

Specifications . . . . . . . . . . . . . . . . . . . . . . . 24

Troubleshooting. . . . . . . . . . . . . . . . . . . . . 27

Messages . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Connection/Installation

Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Parts List for Installation . . . . . . . . . . . . . . 33

Connection (For MEX-N5300BT) . . . . . . . . 34

Connection (For MEX-N4300BT) . . . . . . . . 35

Installation . . . . . . . . . . . . . . . . . . . . . . . . . 38

5GB

Guide to Parts and Controls

 PTY (program type)

Select PTY in RDS.

(browse) (page 13, 14)

Enter the browse mode during playback.

(Not available when a USB device in

Android mode or iPod is connected.)

 Front panel release button

 SRC (source)

Turn on the power.

Change the source.

OFF

Press and hold for 1 second to turn the

source off and display the clock.

Press and hold for more than 2 seconds

to turn off the power and the display.

 Control dial

Rotate to adjust the volume.

PUSH ENTER

Enter the selected item.

Press SRC, rotate then press to change

the source (timeout in 2 seconds).

MENU

Open the setup menu.

VOICE (page 15, 17, 18)

Press and hold for more than 2 seconds

to activate voice dial, voice recognition

(Android smartphone only), or the Siri

function (iPhone only).

N-Mark (MEX-N5300BT only)

Touch the control dial with Android

smartphone to make BLUETOOTH

connection.

 Disc slot

 Display window

 USB port

 (disc eject)

 / (SEEK –/+)

Tune in radio stations automatically.

Press and hold to tune manually.

/ (prev/next)

/ (fast-reverse/fast-forward)

 (back)

Return to the previous display.

MODE (page 11)

 CALL

Enter the call menu. Receive/end a call.

Press and hold for more than 2 seconds

to switch the BLUETOOTH signal.

 Receptor for the remote commander

Main unit

6GB

 Number buttons (1 to 6)

Receive stored radio stations. Press and

hold to store stations.

ALBUM /

Skip an album for audio device. Press and

hold to skip albums continuously.

(Not available when a USB device in

Android mode or iPod is connected.)

(repeat)

(Not available when a USB device in

Android mode is connected.)

(shuffle)

(Not available when a USB device in

Android mode is connected.)

MIC (page 15)

 (play/pause)

 EXTRA BASS

Reinforces bass sound in synchronization

with the volume level. Press to change

the EXTRA BASS setting: [1], [2], [OFF].

 AUX input jack

 DSPL (display)

Press to change display items.

SCRL (scroll)

Press and hold to scroll a display item.

7GB

Detaching the Front Panel

You can detach the front panel of this unit to

prevent theft.

1 Press and hold OFF  until the unit

turns off, press the front panel

release button , then pull the panel

towards you to remove.

Caution alarm

If you turn the ignition switch to the OFF

position without detaching the front panel,

the caution alarm will sound for a few

seconds. The alarm will only sound if the

built-in amplifier is used.

Serial numbers (MEX-N5300BT only)

Make sure the serial numbers on the bottom

of the unit and the back of the front panel

are matched correctly. Otherwise you cannot

make BLUETOOTH pairing, connection and

disconnection by NFC.

Resetting the Unit

Before operating the unit for the first time,

after replacing the car battery, or changing

the connections, you must reset the unit.

1 Press DSPL and CALL for more than

2seconds.

Note

Resetting the unit will erase the clock setting and

some stored contents.

Setting the area/region

After resetting the unit, the area/region

setting display appears.

1 Press ENTER while [SET AREA] is

displayed.

The area/region currently set appears.

2 Rotate the control dial to select

[EUROPE] or [RUSSIA], then press it.

3 Rotate the control dial to select [YES]

or [NO], then press it.

If the setting area/region is changed, the

unit is reset, then the clock is displayed.

This setting can be configured in the general

setup menu (page 19).

Setting the Clock

1 Press MENU, rotate the control dial to

select [GENERAL], then press it.

2 Rotate the control dial to select [SET

CLOCK], then press it.

3 Rotate the control dial to select

[MANUAL], then press it.

The hour indication flashes.

4 Rotate the control dial to set the hour

and minute.

To move the digital indication, press

/ (SEEK –/+).

5 After setting the minute, press MENU.

The setup is complete and the clock

starts.

To display the clock

Press DSPL.

To set the clock automatically

Select [AUTO <RDS>] in step 3.

Getting Started

Attaching the front panel

8GB

Checking the Battery

Voltage

You can check the current battery voltage.

(Not available while the source is off and the

clock is displayed.)

1 Press DSPL repeatedly until the

battery voltage display appears.

Preparing a BLUETOOTH

Device

You can enjoy music, or perform handsfree

calling depending on the BLUETOOTH

compatible device such as a smartphone,

cellular phone and audio device (hereafter

“BLUETOOTH device” if not otherwise

specified). For details on connecting, refer to

the operating instructions supplied with the

device.

Before connecting the device, turn down the

volume of this unit; otherwise, loud sound

may result.

By touching the control dial on the unit with

an NFC* compatible smartphone, the unit is

paired and connected with the smartphone

automatically.

* NFC (Near Field Communication) is a technology

enabling short-range wireless communication

between various devices, such as mobile phones

and IC tags. Thanks to the NFC function, data

communication can be achieved easily just by

touching the relevant symbol or designated

location on NFC compatible devices.

For a smartphone with Android OS 4.0 or

lower installed, downloading the app “NFC

Easy Connect” available on Google Play is

required. The app may not be downloadable

in some countries/regions.

1 Activate the NFC function on the

smartphone.

For details, refer to the operating

instructions supplied with the

smartphone.

2 Touch the N-Mark part of the unit

with the N-Mark part of the

smartphone.

Make sure that lights up on the display

of the unit.

To disconnect using NFC

Touch the N-Mark part of the unit with the

N-Mark part of the smartphone again.

Notes

• When making the connection, handle the

smartphone carefully to prevent scratches.

• One-touch connection is not possible when the

unit is already connected to two NFC compatible

devices. In this case, disconnect either device, and

make connection with the smartphone again.

When connecting a BLUETOOTH device for

the first time, mutual registration (called

“pairing”) is required. Pairing enables this

unit and other devices to recognize each

other. This unit can connect two BLUETOOTH

devices (two cellular phones, or a cellular

phone and an audio device).

1 Place the BLUETOOTH device within

1 m (3 ft) of this unit.

2 Press MENU, rotate the control dial to

select [BLUETOOTH], then press it.

3 Rotate the control dial to select [SET

PAIRING], then press it.

Connecting with a Smartphone

using One-touch connection (NFC)

(MEX-N5300BT only)

Pairing and connecting with a

BLUETOOTH device

9GB

4 Rotate the control dial to select [SET

DEVICE 1]* or [SET DEVICE 2]*, then

press it.

flashes while the unit is in pairing

standby mode.

* [SET DEVICE 1] or [SET DEVICE 2] will be

changed to the paired device name after

pairing is complete.

5 Perform pairing on the BLUETOOTH

device so it detects this unit.

6 Select [MEX-xxxxx] (your model

name) shown in the display of the

BLUETOOTH device.

If your model name does not appear,

repeat from step 2.

7 If passkey* input is required on the

BLUETOOTH device, input [0000].

* Passkey may be called “Passcode,” “PIN code,”

“PIN number” or “Password,” etc., depending

on the device.

When pairing is made, stays lit.

8 Select this unit on the BLUETOOTH

device to establish the BLUETOOTH

connection.

or lights up when the connection is

made.

Note

While connecting to a BLUETOOTH device, this unit

cannot be detected from another device. To enable

detection, enter the pairing mode and search for

this unit from another device.

To start playback

For details, see “Playing a BLUETOOTH

Device” (page 13).

To disconnect the paired device

Perform steps 2 to 4 to disconnect after this

unit and the BLUETOOTH device are paired.

To use a paired device, connection with this

unit is required. Some paired devices will

connect automatically.

1 Press MENU, rotate the control dial to

select [BLUETOOTH], then press it.

2 Rotate the control dial to select [SET

BT SIGNL], then press it.

Make sure that lights up.

3 Activate the BLUETOOTH function on

the BLUETOOTH device.

4 Operate the BLUETOOTH device to

connect to this unit.

or lights up.

Icons in the display:

To connect the last-connected device

from this unit

Activate the BLUETOOTH function on the

BLUETOOTH device.

To connect with the audio device, press SRC

to select [BT AUDIO] and press  (play/

pause).

To connect with the cellular phone, press

CALL.

Note

While streaming BLUETOOTH audio, you cannot

connect from this unit to the cellular phone.

Connect from the cellular phone to this unit instead.

[0000]

Input passkey

Connecting with a paired

BLUETOOTH device

Lights up when handsfree calling is

available by enabling the HFP

(Handsfree Profile).

Lights up when the audio device is

playable by enabling the A2DP

(Advanced Audio Distribution

Profile).

10GB

Tip

With BLUETOOTH signal on: when the ignition is

turned to on, this unit reconnects automatically to

the last-connected cellular phone.

To install the microphone

For details, see “Installing the microphone

(MEX-N5300BT only)” (page 37).

When an iPhone/iPod with iOS5 or later

installed is connected to the USB port, the

unit is paired and connected with the

iPhone/iPod automatically.

To enable BLUETOOTH Auto Pairing, make

sure [SET AUTOPAIR] in [BLUETOOTH] is set

to [ON] (page 21).

1 Activate the BLUETOOTH function on

the iPhone/iPod.

2 Connect an iPhone/iPod to the USB

port.

Make sure that lights up on the display

of the unit.

Notes

• BLUETOOTH Auto Pairing is not possible if the unit

is already connected to two BLUETOOTH devices.

In this case, disconnect either device, then

connect the iPhone/iPod again.

• If BLUETOOTH Auto Pairing is not established, see

“Preparing a BLUETOOTH Device” (page 8).

Connecting a USB Device

1 Turn down the volume on the unit.

2 Connect the USB device to the unit.

To connect an iPod/iPhone, use the USB

connection cable for iPod (not supplied).

Connecting Other Portable

Audio Device

1 Turn off the portable audio device.

2 Turn down the volume on the unit.

3 Connect the portable audio device to

the AUX input jack (stereo mini jack)

on the unit with a connecting cord

(not supplied)*.

* Be sure to use a straight type plug.

4 Press SRC to select [AUX].

To match the volume level of the

connected device to other sources

Start playback of the portable audio device

at a moderate volume, and set your usual

listening volume on the unit.

Press MENU, then select [SOUND]  [SET AUX

VOL] (page 20).

Connecting with an iPhone/iPod

(BLUETOOTH Auto Pairing)

11GB

Listening to the Radio

To listen to the radio, press SRC to select

[TUNER].

1 Press MODE to change the band (FM1,

FM2, FM3 or MW/LW).

2 Press MENU, rotate the control dial to

select [GENERAL], then press it.

3 Rotate the control dial to select [SET

BTM], then press it.

The unit stores stations in order of

frequency on the number buttons.

1 Press MODE to change the band (FM1,

FM2, FM3 or MW/LW).

2 Perform tuning.

To tune manually

Press and hold / (SEEK –/+) to

locate the approximate frequency, then

press / (SEEK –/+) repeatedly to

fine adjust to the desired frequency.

To tune automatically

Press / (SEEK –/+).

Scanning stops when the unit receives a

station.

1 While receiving the station that you

want to store, press and hold a

number button (1 to 6) until [MEM]

appears.

1 Select the band, then press a number

button (1 to 6).

Using Radio Data System

(RDS)

AF continuously retunes the station to the

strongest signal in a network, and TA

provides current traffic information or traffic

programs (TP) if received.

1 Press MENU, rotate the control dial to

select [GENERAL], then press it.

2 Rotate the control dial to select [SET

AF/TA], then press it.

3 Rotate the control dial to select [SET

AF-ON], [SET TA-ON], [SET AF/TA-ON]

or [SET AF/TA-OFF], then press it.

To store RDS stations with the AF and

TA setting

You can preset RDS stations along with an

AF/TA setting. Set AF/TA, then store the

station with BTM or manually. If you preset

manually, you can also preset non-RDS

stations.

To receive emergency announcements

With AF or TA on, emergency

announcements will automatically interrupt

the currently selected source.

To adjust the volume level during a

traffic announcement

Level will be stored into memory for

subsequent traffic announcements,

independently from the regular volume

level.

Listening to the Radio

Storing automatically (BTM)

Tuning

Storing manually

Receiving the stored stations

Setting alternative frequencies

(AF) and traffic announcement

(TA)

12GB

To stay with one regional program

(REGIONAL)

When the AF and REGIONAL functions are

on, you will not be switched to another

regional station with a stronger frequency. If

you leave this regional program’s reception

area, set [SET REGIONAL] in [GENERAL] to

[SET REG-OFF] during FM reception

(page 19).

This function does not work in the UK and

some other areas.

Local Link function (UK only)

This function enables you to select other

local stations in the area, even if they are not

stored on your number buttons.

During FM reception, press a number button

(1 to 6) on which a local station is stored.

Within 5 seconds, press again a number

button of the local station. Repeat this

procedure until the local station is received.

1 Press PTY during FM reception.

2 Rotate the control dial until the

desired program type appears, then

press it.

The unit starts to search for a station

broadcasting the selected program type.

Type of programs

Playing a Disc

1 Insert the disc (label side up).

Playback starts automatically.

Playing a USB Device

In these Operating Instructions, “iPod” is

used as a general reference for the iPod

functions on an iPod and iPhone, unless

otherwise specified by the text or

illustrations.

For details on the compatibility of your iPod,

see “About iPod” (page 23) or visit the

support site on the back cover.

AOA (Android Open Accessory) 2.0, MSC

(Mass Storage Class) and MTP (Media

Transfer Protocol) type USB devices*

compliant with the USB standard can be

used. Depending on the USB device, the

Android mode or MSC/MTP mode can be

selected on the unit.

Some digital media players or Android

smartphones may require setting to MTP

mode.

* e.g., a USB flash drive, digital media player,

Android smartphone

Notes

• For details on the compatibility of your USB device,

visit the support site on the back cover.

• Smartphones with Android OS 4.1 or higher

installed support Android Open Accessory 2.0

(AOA 2.0). However, some smartphones may not

fully support AOA 2.0 even if Android OS 4.1 or

higher is installed.

For details on the compatibility of your Android

smartphone, visit the support site on the back

cover.

Selecting program types (PTY)

NEWS (News), AFFAIRS (Current Affairs), INFO

(Information), SPORT (Sports), EDUCATE

(Education), DRAMA (Drama), CULTURE

(Culture), SCIENCE (Science), VARIED (Varied),

POP M (Pop Music), ROCK M (Rock Music),

EASY M (Easy Listening), LIGHT M (Light

classical), CLASSICS (Serious classical), OTHER

M (Other Music), WEATHER (Weather), FINANCE

(Finance), CHILDREN (Children’s program),

SOCIAL (Social Affairs), RELIGION (Religion),

PHONE IN (Phone In), TRAVEL (Travel), LEISURE

(Leisure), JAZZ (Jazz Music), COUNTRY (Country

Music), NATION M (National Music), OLDIES

(Oldies Music), FOLK M (Folk Music),

DOCUMENT (Documentary)

Playback

13GB

• Playback of the following files is not supported.

MP3/WMA/AAC/FLAC:

–copyright-protected files

– DRM (Digital Rights Management) files

– Multi-channel audio files

MP3/WMA/AAC:

– lossless compression files

Before making a connection, select the USB

mode (Android mode or MSC/MTP mode)

depending on the USB device (page 19).

1 Connect a USB device to the USB port

(page 10).

Playback starts.

If a device is already connected, to start

playback, press SRC to select [USB] ([IPD]

appears in the display when the iPod is

recognized).

2 Adjust the volume on this unit.

To stop playback

Press and hold OFF for 1 second.

To remove the device

Stop playback, then remove the device.

Caution for iPhone

When you connect an iPhone via USB,

phone call volume is controlled by the

iPhone, not the unit. Do not inadvertently

increase the volume on the unit during a

call, as a sudden loud sound may result

when the call ends.

Playing a BLUETOOTH Device

You can play contents on a connected

device that supports BLUETOOTH A2DP

(Advanced Audio Distribution Profile).

1 Make BLUETOOTH connection with

the audio device (page 8).

To select the audio device, press MENU,

then select [BLUETOOTH]  [SET

AUDIODEV] (page 21).

2 Press SRC to select [BT AUDIO].

3 Operate the audio device to start

playback.

4 Adjust the volume on this unit.

Notes

• Depending on the audio device, information such

as title, track number/time and playback status

may not be displayed on this unit.

• Even if the source is changed on this unit,

playback of the audio device does not stop.

• [BT AUDIO] does not appear in the display while

running the “Sony | Music Center” application via

the BLUETOOTH function.

To match the volume level of the

BLUETOOTH device to other sources

Start playback of the BLUETOOTH audio

device at a moderate volume, and set your

usual listening volume on the unit.

Press MENU, then select [SOUND]  [SET BTA

VOL] (page 20).

Searching and Playing

Tracks

Not available when a USB device in Android

mode is connected.

1 During playback, press (repeat) or

(shuffle) repeatedly to select the

desired play mode.

Playback in the selected play mode may

take time to start.

Available play modes differ depending on

the selected sound source.

Not available when a USB device in Android

mode or iPod is connected.

1 During CD or USB playback, press

(browse)* to display the list of search

categories.

When the track list appears, press

(back) repeatedly to display the desired

search category.

* During USB playback, press (browse) for

more than 2 seconds to directly return to the

beginning of the category list.

Repeat play and shuffle play

Searching a track by name

(“Quick-BrowZer™”)

14GB

2 Rotate the control dial to select the

desired search category, then press it

to confirm.

3 Repeat step 2 to search the desired

track.

Playback starts.

To exit the “Quick-BrowZer” mode

Press (browse).

Not available when a USB device in Android

mode or iPod is connected.

1 During CD or USB playback, press

(browse).

2 Press  (SEEK +).

3 Rotate the control dial to select the

item.

The list is jumped in steps of 10% of the

total number of items.

4 Press ENTER to return to the “Quick-

BrowZer” mode.

The selected item appears.

5 Rotate the control dial to select the

desired item, then press it.

Playback starts.

To use a cellular phone, connect it with this

unit. You can connect two cellular phones to

the unit. For details, see “Preparing a

BLUETOOTH Device” (page 8).

Receiving a Call

1 Press CALL when a call is received

with a ringtone.

The phone call starts.

Note

The ringtone and talker’s voice are output from the

front speakers. To select the speakers for handsfree

calling, press MENU, then select [BLUETOOTH] 

[SET VOICE-OUT] (page 21).

To reject the call

Press and hold OFF for 1 second.

To end the call

Press CALL again.

Making a Call

You can make a call from the phonebook or

call history when a cellular phone

supporting PBAP (Phone Book Access

Profile) is connected.

When two cellular phones are connected to

the unit, select either phone.

1 Press CALL.

When two cellular phones are connected

to the unit, rotate the control dial to

select either phone, then press it.

2 Rotate the control dial to select

[PHONE BOOK], then press it.

Searching by skipping items

(Jump mode)

Handsfree Calling (via

BLUETOOTH only)

From the phonebook

15GB

3 Rotate the control dial to select an

initial from the initial list, then press

it.

4 Rotate the control dial to select a

name from the name list, then press

it.

5 Rotate the control dial to select a

number from the number list, then

press it.

The phone call starts.

1 Press CALL.

When two cellular phones are connected

to the unit, rotate the control dial to

select either phone, then press it.

2 Rotate the control dial to select

[RECENT CALL], then press it.

A list of the call history appears.

3 Rotate the control dial to select a

name or phone number from the call

history, then press it.

The phone call starts.

1 Press CALL.

When two cellular phones are connected

to the unit, rotate the control dial to

select either phone, then press it.

2 Rotate the control dial to select [DIAL

NUMBER], then press it.

3 Rotate the control dial to enter the

phone number, and lastly select [ ]

(space), then press ENTER*.

The phone call starts.

* To move the digital indication, press /

(SEEK –/+).

Note

[_] appears instead of [#] on the display.

1 Press CALL.

When two cellular phones are connected

to the unit, rotate the control dial to

select either phone, then press it.

2 Rotate the control dial to select

[REDIAL], then press it.

The phone call starts.

You can make a call by saying the voice tag

stored in a connected cellular phone that

has a voice dialing function.

1 Press CALL.

When two cellular phones are connected

to the unit, rotate the control dial to

select either phone, then press it.

2 Rotate the control dial to select

[VOICE DIAL], then press it.

Alternatively, press and hold VOICE for

more than 2 seconds.

3 Say the voice tag stored on the

cellular phone.

Your voice is recognized, and the call is

made.

To cancel voice dialing

Press VOICE.

Available Operations During

Call

To adjust the ringtone volume

Rotate the control dial while receiving a call.

To adjust the talker’s voice volume

Rotate the control dial during a call.

To adjust the volume for the other party

(Mic gain adjustment)

Press MIC.

Adjustable volume levels: [MIC-LOW], [MIC-

MID], [MIC-HI].

From the call history

By phone number input

By redial

By voice tags

16GB

To reduce echo and noise (Echo

Canceler/Noise Canceler Mode)

Press and hold MIC.

Settable mode: [EC/NC-1], [EC/NC-2].

To switch between handsfree mode

and handheld mode

During a call, press MODE to switch the

phone call audio between the unit and

cellular phone.

Note

Depending on the cellular phone, this operation

may not be available.

“Sony | Music Center” with

iPhone/Android™

Smartphone

Downloading the latest version of “Sony |

Music Center” application is required from

the App Store for iPhone or from available

on Google Play for Android smartphone.

Notes

• For your safety, follow your local traffic laws and

regulations, and do not operate the application

while driving.

• “Sony | Music Center” is an app for controlling

Sony audio devices which are compatible with

“Sony | Music Center”, by your iPhone/Android

smartphone.

• What you can control with “Sony | Music Center”

varies depending on the connected device.

• To make use of “Sony | Music Center” features, see

the details on your iPhone/Android smartphone.

• For further details on “Sony | Music Center,” visit

the following URL: http://www.sony.net/smcqa/

• Visit the website below and check the compatible

iPhone/Android smartphone models.

For iPhone: visit the App Store

For Android smartphone: visit Google Play

1 Make the BLUETOOTH connection

with iPhone/Android smartphone

(page 8).

To select the audio device, press MENU,

then select [BLUETOOTH]  [SET

AUDIODEV] (page 21).

2 Launch the “Sony | Music Center”

application.

3 Press MENU, rotate the control dial to

select [SONY APP], then press it.

Connection to iPhone/Android

smartphone starts.

For details on the operations on iPhone/

Android smartphone, see the help of the

application.

Useful Functions

Establishing the “Sony | Music

Center” connection

17GB

If the device number appears

Make sure that the number is displayed

(e.g., 123456), then select [Yes] on the

iPhone/Android smartphone.

To terminate connection

Press MENU, rotate the control dial to select

[SONY APP], then press it.

Selecting the source or application

You can operate to select the desired source

or application on iPhone/Android

smartphone.

To select the source

Press SRC repeatedly. Alternatively, press

SRC, rotate the control dial to select the

desired source, then press ENTER.

To display the source list

Press SRC.

Announcement of SMS by voice

guide (Android smartphone only)

Messages of SMS are automatically read out

through the car speakers when they are

received.

For details on settings, refer to the help of

the application.

Replying a message of SMS

(Android smartphone only)

You can reply a message by touching the

reply icon.

1 Activate the “Sony | Music Center”

application, then touch the [Reply] (reply)

icon.

The message input display appears on the

“Sony | Music Center” application.

2 Input a reply message by voice recognition.

The list of message candidates appears on the

“Sony | Music Center” application.

3 Rotate the control dial to select the desired

message, then press it.

The message is sent out.

Making sound and display settings

You can adjust the settings relating to sound

and display via iPhone/Android

smartphone.

For details on settings, refer to the help of

the application.

Using Voice Recognition

(Android Smartphone only)

1 Press and hold VOICE to activate

voice recognition.

2 Say the desired voice command into

the microphone.

To deactivate voice recognition

Press VOICE.

Notes

• Voice recognition may not be available in some

cases.

• Voice recognition may not work properly

depending on the performance of the connected

Android smartphone.

• Operate under conditions where noise such as

engine sound is minimized during voice

recognition.

Using “Siri Eyes Free”

“Siri Eyes Free” allows you to use an iPhone

handsfree by simply speaking into the

microphone. This function requires you to

connect an iPhone to the unit via

BLUETOOTH. Availability is limited to iPhone

4s or later. Make sure that your iPhone is

running the latest iOS version.

You must complete BLUETOOTH registration

and connection configurations for the

iPhone with the unit in advance. For details,

see “Preparing a BLUETOOTH Device”

(page 8). To select the iPhone, press MENU,

then select [BLUETOOTH]  [SET AUDIODEV]

(page 21).

18GB

1 Activate the Siri function on the

iPhone.

For details, refer to the operating

instructions supplied with the iPhone.

2 Press and hold VOICE for more than

2 seconds.

The voice command display appears.

3 After the iPhone beeps, speak into

the microphone.

The iPhone beeps again, then Siri starts

responding.

To deactivate “Siri Eyes Free”

Press VOICE.

Notes

• The iPhone may not recognize your voice

depending on usage conditions. (For example, if

you are in a moving car.)

• “Siri Eyes Free” may not function properly, or the

response time may lag in locations where iPhone

signals are difficult to receive.

• Depending on the iPhone’s operating condition,

“Siri Eyes Free” may not function properly, or may

quit.

• If you play a track with an iPhone using the

BLUETOOTH audio connection, when the track

starts playback via BLUETOOTH, “Siri Eyes Free”

automatically quits and the unit switches to the

BLUETOOTH audio source.

• When “Siri Eyes Free” is activated during audio

playback, the unit may switch to the BLUETOOTH

audio source even if you do not specify a track to

play.

• When connecting the iPhone to the USB port, “Siri

Eyes Free” may not function properly, or may quit.

• When connecting the iPhone to the unit via USB,

do not activate Siri with the iPhone. “Siri Eyes Free”

may not function properly, or may quit.

• There is no audio sound while “Siri Eyes Free” is

activated.

Canceling the DEMO Mode

You can cancel the demonstration display

which appears when the source is off and

the clock is displayed.

1 Press MENU, rotate the control dial to

select [GENERAL], then press it.

2 Rotate the control dial to select [SET

DEMO], then press it.

3 Rotate the control dial to select [SET

DEMO-OFF], then press it.

The setting is complete.

4 Press (back) twice.

The display returns to normal reception/

play mode.

Basic Setting Operation

You can set items in the following setup

categories:

General setup (GENERAL), Sound setup

(SOUND), Display setup (DISPLAY),

BLUETOOTH setup (BLUETOOTH), “Sony |

Music Center” setup (SONY APP)

1 Press MENU.

2 Rotate the control dial to select the

setup category, then press it.

The items that can be set differ

depending on the source and settings.

3 Rotate the control dial to select the

options, then press it.

To return to the previous display

Press (back).

Settings

19GB

General Setup (GENERAL)

AREA (area)

Specifies the area/region to use this unit:

[EUROPE], [RUSSIA].

If the area/region currently set is

changed, this unit is reset, then the clock

is displayed.

(Available only while the source is off and

the clock is displayed.)

DEMO (demonstration)

Activates the demonstration: [ON], [OFF].

CLOCK (clock) (page 7)

Sets the clock: [AUTO <RDS>], [MANUAL].

CAUT ALM (caution alarm)

Activates the caution alarm: [ON], [OFF]

(page 7).

(Available only while the source is off and

the clock is displayed.)

BEEP (beep)

Activates the beep sound: [ON], [OFF].

AUTO OFF (auto off)

Shuts off automatically after a certain

time when the unit is turned off and the

clock is displayed (i.e. press and hold OFF

for 1 second): [ON] (30 minutes), [OFF].

STEERING (steering)

Registers/resets the setting of the

steering wheel remote control.

(Available only while the source is off and

the clock is displayed.)

STR CONTROL (steering control)

Selects the input mode of the connected

remote control. To prevent a malfunction,

be sure to match the input mode with the

connected remote control before use.

CUSTOM (custom)

Input mode for the steering wheel

remote control

PRESET (preset)

Input mode for the wired remote

control excluding the steering wheel

remote control

(Automatically selected when [RESET

CUSTOM] is performed.)

EDIT CUSTOM (edit custom)

Registers the functions (SOURCE, ATT,

VOL +/–, SEEK +/–, VOICE, ON HOOK, OFF

HOOK) to the steering wheel remote

control:

 Rotate the control dial to select the

function you want to assign to the

steering wheel remote control, then

press it.

 While [REGISTER] is blinking, press and

hold the button on the steering wheel

remote control you want to assign the

function to. When registration is

complete, [REGISTERED] is displayed.

 To register other functions, repeat

steps  and .

(Available only when [STR CONTROL] is

set to [CUSTOM].)

RESET CUSTOM (reset custom)

Resets the registered functions of the

steering wheel remote control: [YES],

[NO].

(Available only when [STR CONTROL] is

set to [CUSTOM].)

Notes

• While making settings, only button operation

on the unit is available. For safety, park your car

before making this setting.

• If an error occurs while registering, all the

previously-registered information remains.

Restart registration from the function where

the error occurred.

• This function may not be available on some

vehicles. For details on the compatibility of

your vehicle, visit the support site on the back

cover.

USB MODE (USB mode)

Changes the USB mode: [ANDROID],

[MSC/MTP].

(Available only when the USB source is

selected.)

AF/TA (alternative frequencies/traffic

announcement)

Selects the alternative frequencies (AF)

and traffic announcement (TA) setting:

[AF-ON], [TA-ON], [AF/TA-ON], [AF/TA-

OFF].

(Available when any source is selected.)

REGIONAL (regional)

Restricts reception to a specific region:

[ON], [OFF].

(Available only when FM is received.)

20GB

BTM (best tuning memory) (page 11)

(Available only when the tuner is

selected.)

FIRMWARE (firmware)

(Available only while the source is off and

the clock is displayed.)

Checks/updates the firmware version. For

details, visit the support site on the back

cover.

FW VERSION (firmware version)

Displays current firmware version.

FW UPDATE (firmware update)

Enters firmware update process: [YES],

[NO].

Updating the firmware takes a few

minutes to complete. During the update,

do not turn the ignition to the OFF

position, nor remove the USB device.

Sound Setup (SOUND)

This setup menu is not available when the

source is off and the clock is displayed.

EQ10 PRESET (EQ10 preset)

Selects an equalizer curve from 10

equalizer curves or off:

[OFF], [R&B], [ROCK], [POP], [HIP-HOP],

[EDM], [JAZZ], [SOUL], [COUNTRY],

[KARAOKE]*, [CUSTOM].

The equalizer curve setting can be

memorized for each source.

* [KARAOKE] reduces the vocal sound but

cannot fully remove it during playback. Also,

using a microphone is not supported.

EQ10 CUSTOM (EQ10 custom)

Sets [CUSTOM] of EQ10.

Setting the equalizer curve: [BAND1] –

[BAND10] (32 Hz, 63 Hz, 125 Hz, 250 Hz,

500 Hz, 1 kHz, 2 kHz, 4 kHz, 8 kHz, 16 kHz).

The volume level is adjustable in 1 dB

steps, from -6 dB to +6 dB.

BALANCE (balance)

Adjusts the sound balance: [RIGHT-15] –

[CENTER] – [LEFT-15].

FADER (fader)

Adjusts the relative level: [FRONT-15] –

[CENTER] – [REAR-15].

S.WOOFER (subwoofer)

SW LEVEL (subwoofer level)

Adjusts the subwoofer volume level:

[+6 dB] – [0 dB] – [-6 dB].

([ATT] is displayed at the lowest setting.)

SW PHASE (subwoofer phase)

Selects the subwoofer phase: [SUB

NORM], [SUB REV].

LPF FREQ (low pass filter frequency)

Selects the subwoofer cut-off frequency:

[80Hz], [100Hz], [120Hz].

HPF FREQ (high pass filter frequency)

Selects the front/rear speaker cut-off

frequency: [OFF], [80Hz], [100Hz], [120Hz].

AUX VOL (AUX volume)

Adjusts the volume level for each

connected auxiliary device:

[+18 dB] – [0 dB] – [-8 dB].

This setting negates the need to adjust

the volume level between sources.

(Available only when the AUX is selected.)

BTA VOL (BLUETOOTH audio volume)

Adjusts the volume level for each

connected BLUETOOTH device: [+6 dB] –

[0 dB] – [-6 dB].

This setting negates the need to adjust

the volume level between sources.

(Available only when the BT audio or

application is selected.)

Display Setup (DISPLAY)

DIMMER (dimmer)

Change the display brightness:

For MEX-N5300BT:

[OFF], [ON], [AT] (auto), [CLK] (clock).

([AT] is available only when the

illumination control lead is connected,

and the head light is turned on.)

For MEX-N4300BT:

[OFF], [ON], [CLK] (clock).

To set this function to be active only

during a fixed period, select [CLK], then

set the start and end times.

– To set the brightness when the dimmer

function is activated:

Set [DIMMER] to [ON], then adjust

[BRIGHTNESS].

La page charge ...

Sony MEX-N5300BT Le manuel du propriétaire

Ce manuel convient également à

Sony MEX-N5300BT Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents