Lorex E881AP Guide de démarrage rapide

IP PTZ Dome Camera

Quick Start Guide

E881AP Series

lorex.com

EN

Thanks for your purchase of the

IP PTZ Dome Camera. Here’s how

to get started.

For full instructions, refer to the

camera's manual at lorex.com.

Welcome!

Contents

Package contents

Section

Dimensions

Safety precautions

Installation

1

2

3

4

Package contents

PTZ camera

ESD gloves

Allen key (A)

Wall mount

Waterproof tape

Allen key (B) M6x14 screws (x3) Rubber ring

Mounting anchors, mounting

screws, at washers (x4)

Waterproof connector

Power adapter

Safety chain

1

User supplied tools:

Drill Screwdriver

Dimensions

2

6.5”

165mm

10”

254mm

13”

331mm

16.5”

419mm

Weight: 5.3 kg

11.7 lb

WARNING:

Make sure to

install the camera

in a location that

can support the

combined weight of

the camera and wall

mount.

Safety precautions

3

• Make sure to disconnect the power cabling before installing the camera. Camera will begin moving

immediately when power cable is connected.

• Make sure to install the camera in a location that can support the combined weight of the camera

and wall mount (weight: 11.7lb/5.3kg).

• Make sure to secure the camera during installation by connecting the included safety chain.

• Camera is rated for outdoor use. It is recommended to install the camera in a sheltered area, such

as under the eaves on a roof.

• It is recommended to install the camera as high up as possible to get the best possible image.

• Mount the camera where the lens is away from direct and intense sunlight.

• Mount the camera in an area that is visible but out of reach.

• Ensure that the camera wiring is not exposed or easily cut.

• Plan your cable wiring so that it does not interfere with power lines or telephone lines.

• Ensure you adhere to local building codes.

Attention: A REGULATED UL / CSA APPROVED power supply is REQUIRED for use with this

camera (included). Use of a non-regulated, non-conforming power supply can damage this

product and voids the warranty.

Installation

4

Step one.

1. Attach the rubber ring to the

back of the wall mount.

2. Use the allen key (A) with the

at end to attach three M6x14

screws (see Figure 1). Do not

tighten all the way.

3. Use the wall mount to mark

holes for the mounting

anchors and cables.

4. Drill holes (drill bit size - 3/8")

to a depth of 2.8"/70mm in

the mounting surface.

5. Insert the mounting anchors.

M6x14 screws (x3)

Rubber ring

Wall mount

Figure 1

Step two.

1. Connect the safety chain between the

camera and the wall mount to protect the

camera from falling while connecting the

cables (see Figure 2).

Safety chain

Figure 2

CAUTION:

Do not hold the camera from the

cable. Hold the camera from the edge

of the dome cover (see Figure 3).

Figure 3

Step three.

1. Push the connection cables into the

wall mount (see Figure 4).

Connection

cables

Figure 4

Step four.

1. Push the camera into the wall mount

with the at surfaces aligned on the

inside. This will allow the M6x14

screws to align with the holes on

the camera.

2. Use the included allen key (A) to

tighten the M6x14 screws and

secure the camera in

(see Figure 5).

Allen key (A)

Figure 5

a. Fit the o-ring around the camera Ethernet connector.

b. Feed the Ethernet extension cable through the end cap and the barrel then connect the cable

to the camera Ethernet connector.

c. Twist the barrel securely onto the camera Ethernet connector. The o-ring becomes

compressed when the seal is properly tight.

d. Split the stopper to wrap it around the cable between the barrel and end cap as shown above.

e. Push the stopper toward the barrel until it is underneath the teeth at the end of the barrel.

f. Twist the end cap clockwise to secure it onto the barrel. The stopper becomes compressed

and will stick out of the end cap slightly when the seal is properly tight.

Figure 6

Step ve.

1. Connect the connection cables.

Camera Ethernet connector

O-ring

Stopper

Barrel

End cap

To connect the cables using the waterproof connector (see Figure 6):

Figure 7

Step six.

1. Pull the connection cables through the

wall mount and mounting surface.

2. Use the allen key (B), mounting screws,

and at washers (x4) to rmly secure

the wall mount to the mounting surface

(see Figure 7).

Allen key (B)

Mounting screws

and at washers (x4)

Note: If mounting the camera

on a drywall surface, you must

drill at least 2 of the mounting

screws through a wooden stud

to ensure a stable mount.

3. Remove the protective vinyl sheet

covering the camera lens.

Note: For full instructions on controlling the PTZ camera with the NVR, refer to the

PTZ camera's manual at lorex.com.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired

operation.

As our products are subject to continuous improvement, Lorex reserves the right to modify product design,

For up-to-date information and

support please visit:

help.lorex.com

E881AP_QSG_TRILINGUAL_R1

For information about Lorex’s warranty policy,

visit lorex.com/warranty.

Caméra Dôme PTZ IP

Guide de démarrage rapide

SérieE881AP

lorex.com

FR

Bienvenue!

Merci d’avoir acheté la caméra

dôme PTZ IP. Pour commencer

Pour des instructions détaillées,

consultez le manuel de la caméra

sur le site lorex.com.

Bienvenue!

Contenu

Contenu de l’emballage

Section

Dimensions

Mesures de sécurité

Installation

1

2

3

4

Dimensions

Mesures de sécurité

Installation

Contenu de l’emballage

CaméraPTZ

Gants ESD

Clé Allen (A)

Support mural

Ruban d’étanchéité

Clé Allen (B) Vis M6x14 (x3) Bague en

caoutchouc

Ancrages et vis de montage,

rondelles plates (x4)

Connecteur étanche

Bloc d’alimentation

Chaîne de sécurité

1

Outils à fournir par

l’utilisateur:

Perceuse Tournevis

Dimensions

2

6,5po

165mm

10po

254mm

331mm

13po

419mm

16,5po

Poids: 5,3kg

11,7lb

AVERTISSEMENT:

Assurez-vous

d’installer la caméra

dans un endroit qui

peut supporter le

poids combiné de la

caméra et du support

mural.

Mesures de sécurité

3

• S’assurer de débrancher le câblage d’alimentation avant d’installer la caméra. La caméra

commencera immédiatement à bouger lorsque le câble d’alimentation sera branché.

• Assurez-vous d’installer la caméra dans un endroit qui peut supporter le poids combiné de la

caméra et du support mural (poids: 11,7lb/5,3kg).

• Veillez à sécuriser la caméra lors de l’installation au moyen de la chaîne de sécurité fournie.

• La caméra est conçue pour être utilisée à l’extérieur. Il est recommandé d’installer la caméra dans

un endroit couvert, par exemple sous l’avant-toit.

• Il est recommandé d’installer la caméra aussi haut que possible pour obtenir la meilleure image

possible.

• Fixer la caméra à un endroit où la lentille ne sera pas exposée directement à la lumière intense du

soleil.

• Fixer la caméra dans un lieu visible, mais hors de portée.

• S’assurer que le câble de la caméra ne soit pas exposé ou coupé facilement.

• Planier l’installation des câbles pour qu’ils n’interfèrent pas avec les lignes de courant ou les

lignes téléphoniques.

• S’assurer de respecter le code du bâtiment local.

Attention: Un bloc d’alimentation STABILISÉ et CERTIFIÉUL/CSA est NÉCESSAIRE pour

l’utilisation de cette caméra (fourni). L’utilisation d’un bloc d’alimentation non régulé et non

conforme peut endommager ce produit et annuler la garantie.

Installation

4

Première étape.

1. Fixez la bague en caoutchouc

à l’arrière du support mural.

2. Utilisez l’extrémité plate de la

clé Allen (A) pour xer trois

visM6x14 (voir Figure1). Ne

serrez pas complètement.

3. Utilisez le support mural pour

marquer l’emplacement des

trous pour les ancrages de

montage et les câbles.

4. Percez les trous (mèche de

3/8po) à une profondeur de

2,8po/70mm dans la surface

de montage.

5. Insérez les ancrages de

montage.

Vis M6x14 (x3)

Bague en

caoutchouc

Support mural

Figure1

La page charge ...

Lorex E881AP Guide de démarrage rapide

Ce manuel convient également à

Lorex E881AP Guide de démarrage rapide

dans d''autres langues

Documents connexes

Autres documents