Sony STR-DA3200ES Mode d'emploi

2-681-805-12(2)

Multi Channel

AV Receiver

Operating Instructions ________________________

Mode d’emploi ______________________________

Owner’s Record

The model and serial numbers are located on the rear of the unit. Record the

serial number in the space provided below. Refer to them whenever you call

upon your Sony dealer regarding this product.

Model No.

Serial No.

STR-DA3200ES

FR

GB

2

GB

To reduce the risk of fire or electric

shock, do not expose this apparatus to

rain or moisture.

Don’t throw away the battery with

general house waste, dispose of it

correctly as chemical waste.

For customers in the United

States

This symbol is intended to alert the

user to the presence of uninsulated

“dangerous voltage” within the

product’s enclosure that may be of

sufficient magnitude to constitute a

risk of electric shock to persons.

This symbol is intended to alert the

user to the presence of important

operating and maintenance

(servicing) instructions in the

literature accompanying the

appliance.

WARNING

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used

in accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference will

not occur in a particular installation. If this

equipment does cause harmful interference to radio

or television reception, which can be determined by

turning the equipment off and on, the user is

encouraged to try to correct the interference by one

or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment

and receiver.

– Connect the equipment into an outlet on a circuit

different from that to which the receiver is

connected.

– Consult the dealer or an experienced radio/TV

technician for help.

CAUTION

You are cautioned that any changes or modification

not expressly approved in this manual could void

your authority to operate this equipment.

Note to CATV system installer:

This reminder is provided to call CATV system

installer’s attention to Article 820-40 of the NEC

that provides guidelines for proper grounding and, in

particular, specifies that the cable ground shall be

connected to the grounding system of the building,

as close to the point of cable entry as practical.

WARNING

3

GB

About This Manual

• The instructions in this manual are for model STR-

DA3200ES. Check your model number by looking

at the lower right corner of the front panel.

• The instructions in this manual describe the

controls on the supplied remote. You can also use

the controls on the receiver if they have the same

or similar names as those on the remote.

This receiver incorporates Dolby* Digital and Pro

Logic Surround and the DTS** Digital Surround

System.

* Manufactured under license from Dolby

Laboratories.

“Dolby”, “Pro Logic”, “Surround EX”, and the

double-D symbol are trademarks of Dolby

Laboratories.

** Manufactured under license from Digital

Theater Systems, Inc. U.S. Pat.

No’s. 5,451,942; 5,956,674; 5,974,380;

5,978,762; 6,226,616; 6,487,535 and other U.S.

and world-wide patents issued and pending.

“DTS”, “DTS-ES”, “Neo:6”, and “DTS 96/24”

are trademarks of Digital Theater Systems, Inc.

This receiver incorporates High-Definition

Multimedia Interface (HDMI™) technology.

HDMI, the HDMI logo and High-Definition

Multimedia Interface are trademarks or registered

trademarks of HDMI Licensing LLC.

XM is a registered trademark of XM Satellite Radio

Inc.

This product is manufactured under license from

Neural Audio Corporation.

Sony Corporation hereby grants the user a non-

exclusive, non-transferable, limited license right to

use this product under the US and foreign patents

pending and other related technology owned by

Neural Audio Corporation.

“Neural” and “Neural Audio” and “Neural

Surround” are trademarks of Neural Audio

Corporation.

GB

4

GB

Table of Contents

Getting Started

Description and location of parts ..................6

1: Installing speakers ..................................18

2: Connecting speakers ...............................19

3a: Connecting the audio components ........21

3b: Connecting the video components .......26

4: Connecting the antennas (aerials) ...........38

5: Preparing the receiver and the remote ....39

6: Setting the speakers ................................41

7: Calibrating the appropriate settings

automatically

(AUTO CALIBRATION) ......................43

Playback

Selecting a component ................................50

Listening to a Super Audio CD/CD ............52

Watching a DVD .........................................53

Enjoying video games ................................54

Watching video ...........................................55

Amplifier Operations

Navigating through menus ..........................56

Adjusting the level

(Level Settings menu) ............................60

Adjusting the equalizer

(EQ Settings menu) ...............................61

Settings for the surround sound

(Sur Settings menu) ...............................63

Settings for the tuner

(Tuner Settings menu) ...........................65

Settings for the audio

(Audio Settings menu) ...........................66

Settings for the video

(Video Settings menu) ...........................67

Settings for the speakers

(Speaker Settings menu) ........................68

Settings for the system

(System Settings menu) .........................72

Calibrating the appropriate settings

automatically

(Auto Calibration menu) ....................... 73

Enjoying Surround Sound

Enjoying Dolby Digital and DTS surround

sound (A.F.D. mode) ............................. 74

Selecting a pre-programmed sound field

(DCS) .................................................... 76

Using only the front speakers

(2CH STEREO) .................................... 78

Enjoying the surround effect at low volume

levels (NIGHT MODE) ........................ 78

Listening to the sound without any adjustment

(ANALOG DIRECT) ............................ 79

Adjusting the speaker levels and balance

(TEST TONE) ....................................... 80

Resetting sound fields

to the initial settings .............................. 81

Tuner Operations

Listening to FM/AM radio ......................... 82

Presetting radio stations ............................. 83

Listening to the XM Radio ........................ 85

Presetting XM Radio stations .................... 89

Other Operations

Displaying menus of the receiver on the TV

screen .................................................... 91

Naming inputs ............................................ 92

Switching between digital and analog audio

(INPUT MODE) ................................... 93

Listening to digital sound from other inputs

(DIGITAL ASSIGN) ............................ 94

Watching HDMI images from other inputs

(HDMI VIDEO ASSIGN) .................... 95

Watching component images from other

inputs

(COMPONENT VIDEO ASSIGN) ...... 96

5

GB

Changing the display .................................. 97

Using the Sleep Timer ................................ 98

Recording using the receiver ...................... 98

Custom install mode ................................... 99

Listening to the sound in another zone

(Zone 2 operations) ............................. 101

Using a bi-amplifier connection ............... 104

Using the CONTROL S Control

System ................................................. 105

Using the Remote

Operating each component using the

remote ................................................. 107

Programming the remote .......................... 108

Performing several commands in sequence

automatically (Macro Play) ................. 111

Setting remote control codes that are not

stored in the commander ..................... 113

Clearing all the contents of the remote’s

memory ............................................... 115

Changing button assignments

(RM-AAU008 only) ............................ 115

Additional Information

Glossary ................................................... 117

Precautions ............................................... 119

Troubleshooting ....................................... 120

Specifications ........................................... 124

Index ......................................................... 127

6

GB

Description and location of parts

To remove the cover

Press PUSH.

When you remove the cover, keep it out of

reach from children.

Getting Started

Front panel

Name Function

A POWER Press to turn the

receiver on or off (page

39, 52, 53, 54, 55, 81).

B AUTO CAL MIC

jack

Connects to the

supplied optimizer

microphone for the

Digital Cinema Auto

Calibration function

(page 43).

7

GB

Getting Started

C TONE MODE Adjusts FRONT BASS

and FRONT TREBLE.

Press TONE MODE

repeatedly to select

BASS or TREBLE,

then turn TONE to

adjust the level (page

61).

TONE

D Remote sensor Receives signals from

remote commander.

E MEMORY/

ENTER

Press to operate a tuner

(FM/AM/XM) (page

82, 87).

TUNING MODE

TUNING

F CATEGORY

MODE

Used when listening to

XM Radio (page 85).

CATEGORY

+/–

G Display

window

The current status of

the selected component

or a list of selectable

items appears here

(page 8).

H 2CH Press to select sound

field (page 74).

A.F.D.

MOVIE

MUSIC

I POWER Press POWER (ZONE)

to enable operations in

zone 2. Then press

SELECT, then INPUT

SELECTOR

(qh) to

select a source input

into zone 2 (page 101).

SELECT

J MULTI CH IN Press to select the audio

input signal from the

component connected

to the MULTI

CHANNEL INPUT

jack (page 50).

Name Function

K HDMI Press to select input

source from the

component connected

to the HDMI IN jack

(page 27).

L PHONES jack Connects to

headphones (page 77).

M SPEAKERS

(OFF/A/B/A+B)

Press to select A, B,

A+B, OFF of the front

speakers (page 42).

N VIDEO 3 IN/

PORTABLE AV

IN jack

Connect to a portable

audio/video component

such as a camcorder or

video game (page 34,

54).

O MULTI

CHANNEL

DECODING

lamp

Lights up when multi-

channel audio signals

are decoded (page 53).

P INPUT

SELECTOR

Turn to select the input

source to play back

(page 50, 52, 53, 54,

55, 92, 93, 99).

Q MASTER

VOLUME

Turn to adjust the

volume level of all

speakers at the same

time (page 50, 52, 53,

54, 55).

Name Function

8

GB

About the indicators on the display

Name Function

A SW Lights up when sub woofer

selection is set to “YES”

and the audio signal is

output from the SUB

WOOFER jack (page 68).

While this indicator lights

up, the receiver creates a

sub woofer signal based on

the L.F.E. signal in the disc

being played back or the

low frequency components

of the front channels.

B Playback

channel

indicators

L

R

C

SL

SR

S

SBL

SBR

SB

The letters (L, C, R, etc.)

indicate the channels being

played back. The boxes

around the letters vary to

show how the receiver

downmixes the source

sound (based on the speaker

settings).

Front Left

Front Right

Center (monaural)

Surround Left

Surround Right

Surround (monaural or the

surround components

obtained by Pro Logic

processing)

Surround Back Left

Surround Back Right

Surround Back (the

surround back components

obtained by 6.1 channel

decoding)

Example:

Recording format (Front/

Surround): 3/2.1

Output channel: Surround

speakers are set to “NO.”

Sound Field: A.F.D. AUTO

Name Function

LSW

SL

SR

CR

9

GB

Getting Started

C ;DIGITAL

(EX)

Lights up when the receiver

is decoding Dolby Digital

Surround signals. When the

receiver is decoding Dolby

Digital Surround EX

signals, “;DIGITAL EX”

also lights up. When

playing a Dolby Digital

format disc, be sure that you

have made digital

connections and that

INPUT MODE is not set to

“ANALOG” (page 93).

D INPUT Lights up constantly. One of

the input indicators also

lights up according to the

current input.

E AUTO Lights up when INPUT

MODE is set to “AUTO”

(page 93).

F HDMI 1 2 Lights up when the receiver

recognizes a component

connected via an HDMI IN

jack (page 27).

G DTS (-ES) Lights up when the receiver

is decoding DTS signals.

When the receiver is

decoding DTS-ES signals,

“DTS-ES” also lights up.

When playing a DTS

format disc, be sure that you

have made digital

connections and that

INPUT MODE is not set to

“ANALOG” (page 93).

H 96/24 Lights up when the receiver

is decoding DTS96/24 (96

kHz/24 bit).

Name Function

I COAX Lights up when INPUT

MODE is set to “AUTO”

and the source signal is a

digital signal being input

through the COAXIAL

jack, or when INPUT

MODE is set to “COAX”

(page 93).

J OPT Lights up when INPUT

MODE is set to “AUTO”

and the source signal is a

digital signal being input

through the OPTICAL jack,

or when INPUT MODE is

set to “OPT” (page 93).

K ANALOG Lights up when INPUT

MODE is set to “AUTO”

and no digital signal is

being input through the

COAXIAL or OPTICAL

jacks, or when INPUT

MODE is set to

“ANALOG,” or when the

ANALOG DIRECT

function is being used (page

93).

L MULTI IN Lights up when MULTI IN

is selected (page 50).

M SB DEC Lights up when surround

back sound decoding is

activated (page 64).

N XM Lights up when XM Radio

is selected (page 85).

O D.RANGE Lights up when dynamic

range compression is

activated (page 61).

P EQ Lights up when the

equalizer is activated (page

61).

Name Function

continued

10

GB

Q CAT Lights up when “ALL

CATEGORY” mode is

changed to “ONE

CATEGORY” mode during

XM Radio operation (page

85).

R ZONE 2 Lights up while operation in

zone 2 is being enabled.

S SLEEP Lights up when the sleep

timer is activated (page 98).

T L.F.E. Lights up when the disc

being played back contains

an L.F.E. (Low Frequency

Effect) channel and the

L.F.E. channel signal is

actually being reproduced,

the bars underneath the

letters light up to indicate

the level. Since the L.F.E.

signal is not recorded in all

parts of the input signal the

bar indication will fluctuate

(and may turn off) during

playback.

U ;PRO

LOGIC (II/

IIx)

Lights up when the receiver

applies Pro Logic

processing to 2 channel

signals in order to output

the center and surround

channel signals. “;PRO

LOGIC II” also lights up

when the Pro Logic II

MOVIE/MUSIC/GAME

decoder is activated.

“;PRO LOGIC IIx” also

lights up when the Pro

Logic IIx MOVIE/MUSIC/

GAME decoder is activated

(page 75).

Note

This indicator does not light if

both the center and surround

speakers are set to “NO” (page

69).

Name Function

V NEO:6 Lights up when DTS Neo:6

Cinema/Music decoding is

activated (page 75).

W DISCRETE Lights up when DTS-ES

Discrete decoding is

activated (page 64).

X MATRIX Lights up when DTS-ES

Matrix decoding is

activated (page 64).

Y SP-A/SP-B/

SP-OFF

Lights up according to the

speaker system used (page

41).

“SP-OFF” lights up when

“SP-OFF” is selected or

headphones are connected.

Z PRESET Lights up when TUNING

MODE is “PRESET.”

wj Tuner

indicators

Lights up when using the

receiver to tune in radio

stations (page 82–90), etc.

wk MEMORY Lights up when a memory

function, such as Name

Input (page 92) etc., is

activated.

wl VOLUME Displays the current

volume.

Name Function

11

GB

Getting Started

Rear panel

A AUDIO INPUT/OUTPUT section

AUDIO IN/

OUT jacks

Connects to a tape

deck, MD deck or

DAT player, etc

(page 21, 25).

MULTI

CHANNEL

INPUT jacks

Connects to a Super

Audio CD player or

DVD player with an

analog audio jack for

7.1 channel or 5.1

channel sound (page

21, 24).

PRE OUT jacks Connects to an

external power

amplifier.

B DIGITAL INPUT/OUTPUT section

OPTICAL IN/

OUT jacks

Connects to a DVD

player, Super Audio

CD player, etc. The

COAXIAL jack

provides a better

quality sound (page

21, 22, 31).

COAXIAL IN

jacks

HDMI IN/OUT

jacks

Connects to a DVD

player, or a satellite

tuner. An image and

the sound are output

to TV or a projector

(page 27).

L

R

C ANTENNA section

FM ANTENNA

jack

Connects to the FM

wire antenna (aerial)

supplied with this

receiver (page 38).

AM

ANTENNA

jack

Connects to the AM

loop antenna (aerial)

supplied with this

receiver (page 38).

XM

ANTENNA

jack

Connects to the XM

connect-and-Play

antenna (aerial) (not

supplied) (page 86).

D COMPONENT VIDEO INPUT/

OUTPUT section

COMPONENT

VIDEO (Y, P

B

/

C

B

, P

R

/C

R

)

INPUT/

OUTPUT

jacks*

Connects to a DVD

player, TV, or a

satellite tuner. (page

29, 31, 37).

E RS-232C jack

Used for

maintenance and

service.

continued

12

GB

* You can watch the selected input image when you

connect the MONITOR OUT jack to a TV (page

29). You can also display certain menu settings and

the sound field on the monitor when you press ON

SCREEN on the remote (page 91).

F Control jack for Sony equipment

and other external components

CTRL S IN/

OUT jacks

Connects to Sony

TV, DVD player or

VCR with

CONTROL S jack

(page 105).

TRIGGER

OUT jack

Connects to interlock

on/off of the power

supply of other 12V

TRIGGER

compliant

components (page

100).

IR REMOTE

IN/OUT jacks

Connects an IR

repeater (page 101,

102).

G VIDEO/AUDIO INPUT/OUTPUT

section

AUDIO IN/

OUT jacks

Connects to a VCR

or a DVD player etc.

(page 29, 31, 32, 33,

34, 36).

VIDEO IN/

OUT jacks*

S VIDEO IN/

OUT jacks*

H SPEAKERS section

Connects to speakers

(page 19).

L

R

13

GB

Getting Started

You can use the supplied remote RM-AAL003

to operate the receiver and to control the Sony

audio/video components that the remote is

assigned to operate (page 108).

RM-AAL003

Remote commander

Name Function

A AV ?/1

(on/standby)

Press to turn on or off the audio/

video components that the

remote is assigned to operate

(page 108).

If you press the ?/1 (B) at the

same time, it will turn off the

receiver and other Sony

components (SYSTEM

STANDBY).

Note

The function of the AV ?/1

switch changes automatically

each time you press the input

button (C).

B ?/1

(on/standby)

Press to turn the receiver on or

off.

After pressing ZONE 2 (D),

only the receiver in zone 2 is

turned on or off with this button.

To turn off all components,

press ?/1 and AV ?/1 (A) at

the same time (SYSTEM

STANDBY).

C Input

buttons

Press one of the buttons to

select the component you want

to use. To utilize the buttons

with names in pink, press

SHIFT (wg), and then press the

button. When you press any of

the input buttons, the receiver

turns on. The buttons are

factory assigned to control Sony

components (page 50). You can

program the remote to control

non-Sony components

following the steps in

“Programming the remote”

(page 108).

D ZONE 2 Press to enable zone 2 operation

(page 101).

E SLEEP Press to activate the Sleep

Timer function and the duration

which the receiver turns off

automatically (page 98).

F RECEIVER Press to enable the receiver

operation (page 56).

G 2CH Press to select a sound field

(page 74).

A.F.D.

MOVIE

MUSIC

continued

14

GB

H Numeric

buttons

Press to

– preset/tune to preset stations.

– select track numbers of the

CD player, DVD player or

MD deck. Press 0/10 to

select track number 10.

– select channel numbers of

the VCR or satellite tuner.

– After pressing TV (wj),

press the numeric buttons to

select the TV channels.

I ENTER Press to enter the value after

selecting a channel, disc or

track using the numeric buttons.

MEMORY Press to store a tuner station

during tuner operation.

J DISPLAY Press to select information

displayed on the display

window, TV screen of the VCR,

satellite tuner, CD player, DVD

player, or MD deck (page

97).

K After pressing MENU (qd) or

TOP MENU (qk), press V/v, B

or b to select the settings. Then

press to enter the selection

(page 56).

L TOOLS Press to display and select items

from the option menus for DVD

player, etc.

OPTIONS

M MENU Press to display the menu of the

receiver, DVD player, or TV,

etc.

N CATEGORY

+/–

Press to select the category for

XM Radio (page 87).

REPLAY B

·

/

ADVANCE

·

b

Press to replay the previous

scene or fast forward the current

scene of the VCR or DVD

player.

O m/M

a)

x

a)

X

a)

H

b)

./>

a)

Press to operate the DVD

player, CD player, MD deck or

tape deck, etc.

CATEGORY

MODE

Press to select the category

mode for XM Radio (page 87).

TUNING +/– Press to select stations (page 82,

87).

Name Function

V/v/B/b

P PRESET

+

b)

/–

Press to register FM/AM/XM

Radio stations or to select preset

stations.

TV CH +/– Press TV (wj) and then press

TV CH+/– to operate the TV,

satellite tuner, VCR, etc.

Q F1/F2 Press TV (wj) and then press

F1 or F2 to select a component

to operate.

• Hard disk recorder

F1: HDD

F2: DVD

• DVD/VHS combo player

F1: DVD

F2: VHS

TV/VIDEO Press TV/VIDEO and TV (wj)

at the same time to select the

input signal (TV input or video

input).

WIDE Press to select the wide picture

mode.

MACRO1,

MACRO2

Press RECEIVER (6) and

then press MACRO 1 or

MACRO 2 to set up the macro

function (page 111).

R TOP MENU Press to display the menu or

on-screen guide of the DVD

player on the TV screen. Then

use V/v/B/b and to perform

menu operations.

MENU Press to display the menus of

the DVD player on the TV

screen. Then use V/v/B/b and

to perform a menu

operations (page 107).

NIGHT

MODE

Press RECEIVER (6) and

then press NIGHT MODE to

activate the NIGHT MODE

function (page 78).

INPUT

MODE

Press RECEIVER (6) and

then press INPUT MODE to

select the input mode when the

same components are

connected to both digital and

analog jacks (page 93).

S MUTING Press to activate the muting

function (page 51).

Name Function

15

GB

Getting Started

a)

See the table on page 107 for information on the

buttons that you can use to control each

component.

b)

The tactile dot is attached to these buttons (H,

PRESET+). Use as a mark of operation.

Notes

• Some functions explained in this section may not

work depending on the model.

• The above explanation is intended to serve as an

example only. Therefore, depending on the

component, the above operation may not be

possible or may operate differently than described.

T MASTER

VOL +/–

Press to adjust the volume level

of all speakers at the same time

(page 50).

TV VOL +/– Press TV (wj) and then press

TV VOL +/– to adjust the

volume level of the TV.

U DISC SKIP Press to skip a disc when using

a multi-disc changer.

V RETURN/

EXIT O

Press to return to the previous

menu or exit the menu while the

menu or on-screen guide of the

VCR, DVD player, or satellite

tuner is displayed on the TV

screen (page 107).

W ON SCREEN Press to display the receiver

status. Then, if you press

MENU (qd), the menus of the

receiver appear (page 91).

X CLEAR Press to

– clear a mistake when you

press the incorrect numeric

button.

– return to continuous

playback, etc. of the satellite

tuner or DVD player.

>10 Press to select

– track numbers over 10 of the

VCR, satellite tuner, CD

player or MD deck.

– channel numbers of the

Digital CATV terminal.

D.TUNING Press to enter direct tuning

mode (page 83, 88).

Y SHIFT Press to light up the button. It

changes the remote button

function to activate the buttons

with pink printing.

Z A.DIRECT Press to switch the audio of the

selected input to analog signal

without any adjustment (page

79).

wj TV Press to enable TV operation.

wk RM SET UP Press to set up the remote.

Name Function

16

GB

RM-AAU008

This remote is only for zone 2 operations (page

101). You cannot control the main receiver

directly with this remote.

Operating the main receiver from

zone 2

Name Function

A ?/1

(on/standby)

Press to turn a receiver in zone 2

on or off.

B Input

buttons

Press one of the buttons to

select the component you want

to use. When you press any of

the input buttons, the receiver

turns on. The buttons are

factory assigned to control Sony

components as follows. You can

change the button assignments

following the steps in

“Changing button assignments

(RM-AAU008 only)” on page

115.

C MUTING Press to mute the sound.

D MASTER

VOL +/–

Press to adjust the volume level

for multi zone output.

E RM SET UP Press to change the category of

the buttons.

F RM SET UP

indicator

Lights up when data is being

sent or when the remote button

assignment is being preset.

G ZONE 2 Press to select the command

mode of the remote.

* The setting cannot be changed.

Button Assigned Sony

component

VIDEO 1 VCR (VTR mode 3)

VIDEO 2 VCR (VTR mode 1)

VIDEO 3 VCR (VTR mode 2)

DVD DVD player

TV/SAT TV tuner

TAPE/CD-

R

Tape deck B

MD/DAT MD deck

SA-CD/CD Super Audio CD/CD

player

TUNER* Built-in tuner

SOURCE The current input

selected for the main

receiver

17

GB

Getting Started

Operating the components

connected to the main receiver

from zone 2

* The function of these buttons switches

automatically each time you press the input

buttons B. The above explanation is intended to

serve as an example only. Therefore, depending

on the component, the above operation may not

be possible or may operate differently than

described.

Name Function

H Operation

buttons*

The following table describes

the function of the buttons.

I CH/

PRESET/

D.SKIP

+/–*

Press repeatedly to select a

preset station or channel. When

using a multi-disc changer,

press to skip a disc.

Button(s) Function

N Starts play. (Starts play

on the front side of the

cassette.)

n Starts play on the

reverse side of the

cassette.

X Pauses play or

recording, and starts

recording when the

component is in

recording standby.

x Stops play.

./> Skips tracks.

18

GB

1: Installing speakers

This receiver allows you to use a 7.1 channel

system (7 speakers and one sub woofer).

To fully enjoy theater-like multi-channel

surround sound requires five speakers (two

front speakers, a center speaker, and two

surround speakers) and a sub woofer (5.1

channel system).

Example of a 5.1 channel

speaker system configuration

AFront left speaker

BFront right speaker

CCenter speaker

DSurround left speaker

ESurround right speaker

HSub woofer

You can enjoy high fidelity reproduction of

DVD software recorded sound in the Surround

EX format if you connect one additional

surround back speaker (6.1 channel system) or

two surround back speakers (7.1 channel

system). (see “Using the surround back

decoding mode (SB DECODING)” on page

64).

Example of a 7.1 channel

speaker system configuration

AFront left speaker

BFront right speaker

CCenter speaker

DSurround left speaker

ESurround right speaker

FSurround back left speaker

GSurround back right speaker

HSub woofer

Tips

• When you connect a 6.1 channel speaker system,

place the surround back speaker behind the

listening position.

• Since the sub woofer does not emit highly

directional signals, you can place it wherever you

want.

Enjoying a 5.1/7.1 channel

system

19

GB

Getting Started

2: Connecting speakers

AFront speaker A (L)

BFront speaker A (R)

CCenter speaker

DSurround speaker (L)

ESurround speaker (R)

FSurround back speaker (L)

b)

GSurround back speaker (R)

b)

HSub woofer

c)

a)

If you have an additional front speaker

system, connect them to the FRONT

SPEAKERS B terminals. You can select

the front speaker system you want to use

with the SPEAKERS (OFF/A/B/A+B) on

the front panel (page 42).

b)

If you connect only one surround back

speaker, connect it to the SURROUND

BACK SPEAKERS L terminals.

HGF

BADEC

AB

FRONT SPEAKERS

B terminals

a)

A Monaural audio cord (not supplied)

B Speaker cords (not supplied)

continued

20

GB

c)

When you connect a sub woofer with an auto

standby function, turn off the function when

watching movies. If the auto standby

function is set to on, it turns to standby mode

automatically based on the level of the input

signal to a sub woofer, then sound may not

be output.

Note

When you connect all the speakers with a nominal

impedance of 8 ohms or higher, set “SP.

IMPEDANCE” in the System Settings menu to “8

ohm.” In other connections, set it to “4 ohm.” For

details, see “6: Setting the speakers” (page 41).

Tip

To connect certain speakers to another power

amplifier, use the PRE OUT jacks. The same signal

is output from both the SPEAKERS terminals and

the PRE OUT jacks. For example, if you want to

connect just the front speakers to another amplifier,

connect that amplifier to the PRE OUT FRONT L

and R jacks.

ZONE 2 connection

You can assign the SURROUND BACK

SPEAKER terminals F and G to the

speakers of the ZONE 2. Set the surround back

speaker settings (page 69) to “ZONE 2.”

See “Listening to the sound in another zone

(Zone 2 operations)” (page 101) for details of

on connection and operation in zone 2.

La page charge ...

Sony STR-DA3200ES Mode d'emploi

Sony STR-DA3200ES Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents