Sauder 420567 Mode d'emploi

Taper
Mode d'emploi
sauder.com
Night Stand
Model 420567
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-19
Français pg 20-22
Español pg 23-25
Lot # 530076 05/24/19
Purchased: __________________
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
Share your journey!
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.
Prefer the phone? Give us a ring at
1-800-523-3987.
Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays)
WARNING
CHOKING HAZARD - Small Parts
Not for children under 3 years.
Adult assembly required.
Table of Contents Assembly Tools Required
2-3
4
5-19
20-22
23-25
26
27
Part Identifi cation
Hardware Identifi cation
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
420567 www.sauder.com/servicePage 2
Part Identifi cation
å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identifi cation to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C2 TOP (1)
D BOTTOM (1)
D24 RIGHT DRAWER SIDE (1)
D25 LEFT DRAWER SIDE (1)
D109 DRAWER BACK (1)
D716 DRAWER BOTTOM (1)
E BACK (1)
F RIGHT FRONT LEG (1)
G LEFT FRONT LEG (1)
H REAR LEG (2)
I DRAWER FRONT (1)
O BOTTOM MOLDING (1)
P END MOLDING (2)
Part Identifi cation
420567www.sauder.com/service
Page 3
A
B
C2
D
E
F
G
H
I
P
O
H
P
D24
D25
D716
D109
Hardware Identifi cation
å Screws are shown actual size. You may receive extra hardware with your unit.
420567 www.sauder.com/servicePage 4
HIDDEN CAM - 12
1F
GOLD 5/16" FLAT HEAD SCREW - 8
3S
CAM SCREW - 4
8F
CAM DOWEL - 8
2F
SLIDE CAM - 2
10A
BLACK 9/16" FLAT HEAD SCREW - 4
32S
BLACK 1-1/8" MACHINE SCREW - 1
21S
BLACK 2-1/4" FLAT HEAD SCREW - 4
26S
NAIL - 16
1N
35AA
UNIVERSAL CABINET RAIL - 2
35AC
DRAWER RIGHT - 1
35AD
DRAWER LEFT - 1
12E
TACK GLIDE - 4
30S
BLACK 1-9/16" FLAT HEAD SCREW - 4
KNOB - 1
5K
Step 1
Look for this icon. It means a
video assembly tip is available at
www.sauder.com/service/tips
å
Assemble your unit on a carpeted fl oor or on the empty
carton to avoid scratching your unit or the fl oor.
å
Push eight HIDDEN CAMS (1F) into the ENDS (A and B)
and BOTTOM (D). Then, insert the metal end of a CAM
DOWEL (2F) into each HIDDEN CAM.
å
NOTE: Use the exact holes shown.
420567www.sauder.com/service
Page 5
A
B
D
Do not tighten the HIDDEN CAMS in this step.
(8 used)
Arrow
1F
2F
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Arrow
1F
2F
Step 2
å
Push four HIDDEN CAMS (1F) into the ENDS (A and B).
A
B
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole
Arrow
420567 www.sauder.com/servicePage 6
Just think. The sooner
you do this, the sooner
you do something else.
1F
Arrow
1F
Arrow
å
Turn four CAM SCREWS (8F) into the FRONT LEGS (F and G).
Step Step 3
8F
(4 used)
F
G
420567www.sauder.com/service
Page 7
Step Step 4
å
Fasten the ENDS (A and B) to the FRONT LEGS (F and G).
Tighten four HIDDEN CAMS.
1
2
B
A
These surfaces
should be even.
Surface with HIDDEN CAMS
Surface with HIDDEN CAMS
F
G
These surfaces
should be even.
Angled edge
Angled edge
Edge with CAM DOWELS
Edge with CAM DOWELS
420567 www.sauder.com/servicePage 8
Step Step 5
å
Turn four BLACK 9/16" FLAT HEAD SCREWS (32S) into
the ENDS (A and B) until the shoulders of the SCREWS
rest on the surfaces of the ENDS.
å
NOTE: Do not overtighten the SCREWS.
å
Slide the END MOLDINGS (P) onto the ENDS (A and B).
Line up the grooves in the MOLDINGS over the heads of
the SCREWS in the ENDS.
å
NOTE: If the MOLDING comes up o of the SCREWS,
remove it and slide it on again.
These edges
should be even.
BLACK 9/16" FLAT HEAD SCREW
(4 used in this step)
32S
B
A
P
P
Shoulder
Shoulder
Apply pressure with your hands
as you guide the MOLDINGS over
the SCREWS and onto the ENDS.
Apply pressure with your hands
as you guide the MOLDINGS over
the SCREWS and onto the ENDS.
These edges
should be even.
32S
Surface without
HIDDEN CAMS
Surface without
HIDDEN CAMS
420567www.sauder.com/service
Page 9
Step Step 6
å
Fasten the REAR LEGS (H) to the ENDS (A and B). Use four
BLACK 2-1/4" FLAT HEAD SCREWS (26S).
B
A
These surfaces
should be even.
Surface with HIDDEN CAMS
Surface with HIDDEN CAMS
H
H
These surfaces
should be even.
Angled edge
Angled edge
Edge with CAM DOWELS
Edge with CAM DOWELS
BLACK 2-1/4" FLAT HEAD SCREW
(4 used in this step)
26S
420567 www.sauder.com/servicePage 10
Step Step 7
å
Fasten the UNIVERSAL CABINET RAILS* (35AA) to
the ENDS (A and B). Use four GOLD 5/16" FLAT
HEAD SCREWS (3S) through holes #1 and #3.
å
*patent pending glide system
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
3S
Glide end
3
2
1
1
2
3
VIEW THE DRAWER GLIDE VIDEO
Glide end
B
A
H
H
420567www.sauder.com/service
Page 11
Don't worry. It isn't
Rome. This can be built
in a day.
Step Step 8
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
These edges
should be even.
Surface with holes
B
å
Fasten the LEFT END (B) to the TOP (C2). Tighten two
HIDDEN CAMS.
Surface with
HIDDEN CAMS
Glide end
C2
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
420567 www.sauder.com/servicePage 12
Meet Part (C2). This component has been
engineered to be lighter, stronger, faster… well
ok. Not technically faster. But defi nitely makes
for a sturdier night stand that’s easier to
assemble and friendlier to the environment.
Step Step 9
å
Fasten the BOTTOM (D) to the LEFT END (B). Tighten two
HIDDEN CAMS.
å
Slide the BOTTOM MOLDING* (O) onto the notched edge
of the BOTTOM (D).
å
*U.S. Patent No. 5,499,886
Arrow
Minimum
190 degrees
Maximum
210 degrees
Notched edge
O
D
Surface with
HIDDEN CAMS
B
420567www.sauder.com/service
Page 13
The large groove is
closer to this edge.
Step
å
Fasten the RIGHT END (A) to the TOP (C2) and BOTTOM (D).
Tighten four HIDDEN CAMS.
Step 10
Arrow
Minimum
190 degrees
Maximum
210 degrees
D
A
C2
Surface without
HIDDEN CAMS
420567 www.sauder.com/servicePage 14
Step Step 11
å
Carefully turn your unit over onto its front edges. Lay the
BACK (E) over your unit.
å
Make equal margins along all four edges of the BACK (E).
Push on opposite corners of your unit if needed to make
it "square".
å
Fasten the BACK (E) to your unit using the NAILS (1N).
å
With a hammer, gently tap four TACK GLIDES (12E) into
the LEGS (F, G, and H).
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
NAIL
(16 used in this step)
1N
12E
F
E
H
G
H
420567www.sauder.com/service
Page 15
Unfi nished surface
Step 12
VIEW THE T-LOCK BOX VIDEO
å
Fasten the DRAWER BACK (D109) to the DRAWER SIDES (D24 and D25). Use four BLACK 1-9/16" FLAT
HEAD SCREWS (30S).
å
NOTE: Be sure the DRAWER BOTTOM (D716) inserts into the groove of the DRAWER BACK (D109).
12
3
å
Insert the DRAWER SIDES (D24 and D25) at an angle
into the slot at each end of the DRAWER FRONT (I).
å
Slide the DRAWER BOTTOM (D716) into the grooves in the
DRAWER SIDES (D24 and D25) and DRAWER FRONT (I).
The tabs should insert freely
into the slots. Gently tilt the
DRAWER SIDES side to side
until the tabs slip into the slots.
Groove
Be sure the DRAWER
BOTTOM inserts into the
DRAWER FRONT groove.
D24
D25
D716
D716
D24
D25
D109
D25
I
I
Unfi nished surface
D24
With the palm of your hand,
tap the DRAWER BOTTOM
down into the groove.
Start each screw a few turns before
completely tightening any of them.
BLACK 1-9/16" FLAT HEAD SCREW
(4 used in this step)
30S
420567 www.sauder.com/servicePage 16
å
Insert a SLIDE CAM (10A) into each DRAWER SIDE (D24 and D25).
å
Fasten the DRAWER RIGHT (35AC) to the RIGHT DRAWER SIDE (D24)
and the DRAWER LEFT (35AD) to the LEFT DRAWER SIDE (D25). Use
four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #2.
å
NOTE: The screw head in the CAM must be visible through the slotted
hole in the SLIDE.
å
NOTE: The glides are not intended to rotate.
Step 13
420567www.sauder.com/service
Page 17
1
2
1
2
Screw head - turn CAM to line up holes
in SLIDES with holes in DRAWER SIDES.
10A
10A
D25
D24
Glide end
Glide end
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
3S
VIEW THE DRAWER GLIDE VIDEO
If you're doing this to
help a friend, don't
leave without a bite.
Step 14
å
Carefully stand your unit upright.
å
To insert the drawer into your unit, tip the front of the
drawer down and drop the glides on the drawer behind
the glides on the unit. Lift the front of the drawer up and
slide it into the unit.
å
Fasten the KNOB (5K) to the DRAWER FRONT (I). Use a
BLACK 1-1/8" MACHINE SCREW (21S).
420567 www.sauder.com/servicePage 18
30 lbs.
15 lbs.
25 lbs.
I
BLACK 1-1/8" MACHINE SCREW
(1 used in this step)
21S
5K
Step 15
420567www.sauder.com/service
Page 19
å
To make adjustments to the drawer, loosen SCREW #2 in the SLIDES a 1/4 turn, then turn the CAM clockwise or
counter-clockwise. Notice how the drawer raises or lowers as you turn the CAM. The higher the screw in the oblong hole,
the higher your drawer front will be. The lower the screw, the lower the drawer front. By adjusting the drawer this way, it
will help the DRAWER FRONT line up better when closed. Tighten the SCREW when fi nished with adjustments.
å
NOTE: Please read the back pages of the instruction booklet for important safety information.
å
This completes assembly. Clean with a damp cloth. Wipe dry.
The higher the screw in the oblong hole,
the higher your drawer front will be. The
lower the screw, the lower the drawer front.
Loosen screw #2 a 1/4 turn, turn the cam a 1/4 turn
maximum in both the clockwise and counter-clockwise
directions to make adjustments, and then tighten screw #2.
Cam
And to celebrate, why not share your success story at Walmart.com or
A l’usage exclusif du
Canada Noter la date
dachat de cet élément
et conserver le livret
pour future référence.
Pour contacter Sauder
en ce qui concerne cet
élément, faire référence
au numéro de lot et
numéro de modèle en
appelant notre numéro
sans frais.
Lot nº : ____________
Date de
lachat: ____________
LISTE DE PIÈCES
REFERENCE DESCRIPTION QUANTITÉ
LISTE DE PIÈCES
REFERENCE DESCRIPTION QUANTITÉ
NOUS SOMMES LA POUR VOUS AIDER!
Nous faisons de notre mieux pour nous assurer que votre meuble
arrive dans d’excellentes conditions. Nos représentants du service
Clientèle sont aimables et prêts à vous aider au cas où une pièce
aurait été endommagée ou manquerait (ou si vous aviez besoin
daide pour lassemblage). NE RAMENEZ PAS LE MEUBLE AU
MAGASIN. Au Canada, composez ce numéro dappel gratuit:
1-800-523-3987
Du lundi au vendredi, de 9 heures du matin à
5:30 heures du soir (horaire Côte Est)
(sauf jours fériés)
Si une pièce a besoin d’être remplacée, la pièce de remplacement
sera envoyée dans les 48 heures. (Sauf week-ends et jours fériés)
Utilisez les instructions dassemblage en français avec les
schémas étape par étape du manuel d’instruction en anglais.
Chaque étape en français correspond à la même étape
en anglais. La pièce devant être attachée à l’élément est
représentée en gris sur les schémas de chaque étape pour plus
de précision. Comparer la “Liste de pièces” ci-dessous avec
la “PART IDENTIFICATION” du manuel en anglais pour vous
familiariser avec les pièces avant lassemblage.
REMARQUE : CE MANUEL D’INSTRUCTIONS CONTIENT
D’IMPORTANTES INFORMATIONS RELATIVES À LA SÉCURITÉ.
À LIRE ET CONSERVER POUR TOUTE RÉFÉRENCE FUTURE.
Chevet
35AA
GLISSIÈRE D'ÉLÉMENT UNIVERSELLE.....2
35AC
TIROIR DROIT .................................................................1
35AD
TIROIR GAUCHE ...........................................................1
10A EXCENTRIQUE DE COULISSE .........................2
12E PATIN .....................................................................................4
1F EXCENTRIQUE ESCAMOTABLE ...................12
2F CHEVILLE D'EXCENTRIQUE ..............................8
8F VIS D'EXCENTRIQUE ...............................................4
5K BOUTON .............................................................................1
1N CLOU .................................................................................16
3S VIS TÊTE PLATE 8 mm DORÉE ......................8
21S VIS À MÉTAUX 28 mm NOIRE ..........................1
26S VIS TÊTE PLATE 57 mm NOIRE .....................4
30S VIS TÊTE PLATE 40 mm NOIRE ....................4
32S VIS TÊTE PLATE 14 mm NOIRE ......................4
A EXTRÉMITÉ DROITE ..................................................1
B EXTRÉMITÉ GAUCHE ...............................................1
C2 DESSUS ...............................................................................1
D DESSOUS ...........................................................................1
D24 CÔTÉ DROIT DE TIROIR ........................................1
D25 CÔTÉ GAUCHE DE TIROIR ..................................1
D109
ARRIÈRE DE TIROIR ...................................................1
D716
FOND DE TIROIR ..........................................................1
E ARRIÈRE ..............................................................................1
F PIED AVANT DROIT ....................................................1
G PIED AVANT GAUCHE .............................................1
H PIED ARRIÈRE ................................................................2
I DEVANT DE TIROIR ....................................................1
O MOULURE DE DESSOUS ......................................1
P MOULURE D’EXTRÉMITÉ .....................................2
420567 www.sauder.com/servicePage 20
Modèle 420567
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28

Sauder 420567 Mode d'emploi

Taper
Mode d'emploi