Kenmore 86485 Manuel utilisateur

Marque: Kenmore

Modèle: 86485

Taper: Manuel utilisateur

Ce manuel convient également à

86482

2181051A

www.sears.com

Sears Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

Sears Canada, Inc., Toronto, Ontario, Canada M5B 2B8

Clear Ice Maker

Use & Care Guide

Fábrica de hielo transparente

Manual de Uso y Cuidado

Machine à glaçons transparents

Guide d’utilisation et d’entretien

Models, Modelos, Modèles: 86482, 86485

ENGLISH ESPAÑOL FRANÇAIS

CONTENTS

Page

Warranty...........................................................................2

Ice Maker Safety..............................................................3

Parts and Features..........................................................3

Installation Instructions..................................................4

Electrical requirements ...............................................4

Space requirements....................................................4

Unit wiring diagrams...................................................5

Installing the ice maker...............................................5

Checking operation.....................................................6

Changing the door panels...........................................7

Operating Instructions....................................................8

How the ice maker makes ice.....................................8

Things to remember....................................................8

Setting the controls.....................................................8

General Cleaning and Care ............................................9

Cleaning exterior surfaces..........................................9

Cleaning and sanitizing the ice making system..........9

Cleaning the condenser............................................10

Removing and cleaning the interior components .....10

Filtering and treating water .......................................11

Vacation and Moving Care ...........................................12

Before Calling for Service ............................................13

Sears Toll Free Numbers..............................................40

Warranty

FULL ONE-YEAR WARRANTY

For one year from the date of purchase, when the ice maker

is used for residential use and is operated and maintained

according to instructions attached to or furnished with the ice

maker, Sears will repair the ice maker free of charge, if de-

fective in materials or workmanship.

LIMITED ONE-YEAR WARRANTY

For one year from the date of purchase, when the ice maker

is used for commercial use and is operated and maintained

according to instructions attached to or furnished with the ice

maker, Sears will provide, free of charge, replacement parts

for any parts defective in materials or workmanship. You pay

for labor.

FULL FIVE-YEAR WARRANTY

ON SEALED REFRIGERATION

SYSTEM

For five years from the date of purchase, when the product is

operated and maintained according to instructions attached

to or furnished with the product, Sears will repair the sealed

system (consisting of: refrigerant, connecting tubing, and

compressor motor), free of charge, if defective in materials or

workmanship.

This warranty gives you specific legal rights, and you may

also have other rights which vary from state to state.

WARRANTY SERVICE IS AVAILABLE BY SIMPLY CON-

TACTING THE NEAREST SEARS STORE OR

SERVICE CENTER THROUGHOUT THE UNITED STATES.

Sears, Roebuck and Co. • D/817 WA • Hoffman Estates, IL 60179

COPY YOUR MODEL AND SERIAL NUMBERS HERE.

When you need service, or call with a question, have this

information ready:

Model Number

Serial Number

Purchase Date

Sears Service Center

and Telephone Number

ENGLISH

Parts and Features

Model and

serial number

plate

(on left interior

cabinet flange)

Ice retainer

baffle

Lower access

panel

Ice thickness

control knob

Ice bin

Ice scoop

Cycle

control

knob

Ice Maker Safety

You will be killed or seriously injured if you don’t

follow instructions.

You can be killed or seriously injured if you don’t

follow instructions.

Your safety and the safety of others is very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey

all safety messages.

This is the safety alert symbol.

This symbol alerts you to hazards that can kill or hurt you and others.

All safety messages will be preceded by the safety alert symbol and the word “DANGER” or

“WARNING.” These words mean:

wDANGER

wWARNING

All safety messages will identify the hazard, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING:

To reduce the risk of fire, electric shock, or injury when using your ice maker, follow these basic

precautions:

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord.

SAVE THESE INSTRUCTIONS

• Disconnect power before cleaning.

• Disconnect power before servicing.

• Replace all panels before operating.

• Use two or more people to move and install ice maker.

Electrical requirements

A 115 Volt, 60 Hz., AC only, 15 ampere fused electrical supply

circuit, properly grounded in accordance with the National

Electrical Code and local codes and ordinances, is required.

It is recommended that a separate circuit, serving only this

appliance, be provided. Use a receptacle which cannot be

turned off with a switch or pull chain.

NOTE: A time delay fuse or circuit breaker is recommended.

Grounding method

For your personal safety, this appliance must be grounded.

This appliance is equipped with a power supply cord having

a 3 prong grounding plug. To minimize possible shock

hazard, the cord must be plugged into a mating, 3 prong,

grounding-type wall receptacle, grounded in accordance with

the National Electrical Code and local codes and ordinances.

If a mating wall receptacle is not available, it is the personal

responsibility of the customer to have a properly-grounded,

3 prong wall receptacle installed by a qualified electrician.

wWARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in

death, fire, or electrical shock.

Installation Instructions

3-prong grounding

type wall receptacle

Ground prong

Space requirements

• To ensure proper ventilation for your ice maker, the front

side must be completely unobstructed. The unit may be

closed-in on the top and three sides, but the installation

should allow the ice maker to be pulled forward for servicing

if necessary.

• Installation of the ice maker requires a cold water supply

inlet of

⁄4" (6 mm) OD soft copper tubing with a shut-off

valve and either a gravity-drain system or condensate pump

to carry the water to an existing drain.

• Choose a well ventilated area with temperatures above 55°F

(13°C) and below 110°F (43°C). Best results are obtained

between 70°F (21°C) and 90°F (32°C). This unit MUST be

installed in an area protected from the elements, such as

wind, rain, water spray, or drip.

• When installing the ice maker under a counter, follow the

recommended opening dimensions shown.

NOTE: Do not kink or pinch the power supply cord between

the ice maker and cabinet.

Built-in Opening Dimensions

⁄2"

(88 cm)

90°

9" max

(23 cm)

Locate

outlet within

this space

18" (46 cm)

⁄2" (11.5 cm)

To center line

Unit wiring diagrams

This model operates at 115 Volts, except for the cutter grid

circuit which operates at 8.5 Volts at 1 Amp. Maximum fuse

size used should be 15 amps.

The compressor runs at all times except when the bin

thermostat is satisfied. This de-energizes the system except

for the transformer and cutter grid.

Under normal operating conditions, when the evaporator

reaches the preset temperature (10°F [-12°C] to -3°F

[-19°C], depending on ice thickness), the evaporator

thermostat opens, terminating operation of the fan motor

and pump motor. The hot gas solenoid and the water valve

solenoid are energized at this time and remain energized

until the evaporator reaches 38°F (3°C).

CLEAN

OFF

SERVICE

SWITCH

8.5 V

115 V

GRID

TRANSFORMER

COMPRESSOR

START RELAY

OVERLOAD

WATER PUMP

CONDENSER

FAN

115 VOLTS

60 HERTZ

BIN

THERMOSTAT

EVAPORATOR

THERMOSTAT

L N

HOT GAS

SOL

W Y

CUTTER

WATER

VALVE

SOL

BK / W

BIN

THERMO

EVAP

THERMO

SERVICE

SWITCH

BK/ W

MOT

PUMP

GRID

115 V

60 HZ

1 PH

FAN

COMPRESSOR

WATER

HOT GAS

SOL

N.C.

SOL

N.C.

START

RELAY

OVERLOAD

PLUG

115V

TRANS

OROR

G/Y

CAB

SHELF

CABINET

8.5V

CONTROL

BRACKET

MOT

COLOR CHART

R Red

BK Black

BL Blue

W White

Y Yellow

OR Orange

Black/White

Tracer

Green/Yellow

Tracer

BK/W

G/Y

SYMBOL CODE

CONNECTOR - SCREW ON

CONNECTOR - CLOSED END

DISCONNECT TERMINAL

PERMANENT CONNECTION

PLUG CONNECTOR

GROUND (CHASSIS)

wWARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all panels before operating.

Failure to do so can result in death or

electrical shock.

Installing the ice maker

Prepare the ice maker

1. Remove the lower access panel. Take out the screws

securing the grille at the bottom and the one screw from

the center of the front panel support and lift it free of the

cabinet.

2. Turn the fan by hand to make certain it moves freely.

3. Loosen the thumb screws holding the cutter grid and

water pan to “thumb tight,” to make water system cleaning

and sanitizing easier. See the “Removing and cleaning

the interior components” section.

wWARNING

Excessive Weight Hazard

Use two or more people to move and install

ice maker.

Failure to do so can result in back or other injury.

Screw

ENGLISH

Connect to the drain

(observe local codes)

1. The unit is provided with a gravity-drain system.

2. The ideal installation has a standpipe (1

⁄4" [32 cm]

minimum) installed directly below the outlet of the drain

tube.

3. It may be desirable to insulate the drain line thoroughly up

to the drain inlet.

4. Replace the lower access panel and the screws.

5. Plug into 3 prong grounded outlet.

Alternate method:

If a drain connection directly below the drain tube outlet is not

available, install a UL listed drain pump in the rear compart-

ment of the ice maker.

Drain pump specifications:

• UL listed and have a UL listed, 120 VAC, 3-wire,

grounded service cord.

• Overall outside dimensions (maximum): 15" (38 cm) wide x

6" (15 cm) deep x 9

⁄2" (24 cm) high.

• Pump flow rate (minimum): 0.4 gpm @ 12 ft. lift.

• Operating temperature range: 55°F to 110°F.

Checking operation

• Start the unit by turning the Cycle Control to ON and

opening the water line valve.

NOTE: Left is OFF – Middle is ON – Right is CLEAN. In the

CLEAN position, only the water pump operates.

• Use a flashlight to look through the space between the

cutter grid and liner to check for even water flow over the

freezing plate. Unit must be level for proper operation.

Connect to water

(observe local codes)

1. Use

⁄4" (6 mm) OD soft copper tubing for the cold water

supply.

2. Provide a convenient manual shut-off valve in the

water line. Do not use a piercing-type or

⁄16-inch saddle

valve which reduces water flow and clogs more easily.

NOTE: Always purge the water line before making the final

connection to the inlet of the water valve to prevent

possible water valve malfunction.

3. Position the tubing so it can enter the access hole

located at the right hand rear of the cabinet. The tubing

should extend beyond the cabinet front when the

cabinet is pushed back into position.

NOTE: After the cabinet is in place, bend the tubing to

meet the connection at the water valve. The garden hose-

threaded compression fitting is found in the parts bag

which is shipped under the ice scoop. This joint

provides a convenient disconnect for servicing. Be sure

the tubing is clear of compressor to prevent rattle.

Leveling the ice maker

1. After placing unit in position, check to make certain the

unit is level side-to-side and front-to-back. Accurate

leveling is important for proper operation.

2. Unit should be shimmed so that it is solid as well as level.

The shims should be of hard, permanent-type material.

3. If required by sanitation code, seal the cabinet to the floor

with an approved caulking compound after all water and

electrical connections have been made.

/4"

/8"

/4"

Right End View

⁄4" (19 mm)

⁄8" (606 mm)

⁄4"

(95 mm)

⁄4" (6 mm) OD

water line com-

pression fitting at

water valve

Bend field-supplied

water line to

connect to water

valve fitting

Water

inlet

solenoid

valve

Drain tube

/8"

/2"

/32"

Back View

⁄8"

(200 mm)

⁄2"

(190 mm)

(229 mm)

(76 mm)

⁄32"

(874 mm)

⁄2"

(38 mm)

Access hole for

field-supplied

water line

4" long

(102 mm)

⁄8" ID

(16 mm) rubber

drain tube –

run to open

drain

⁄4" (32 mm)

minimum

diameter

standpipe

⁄2"

(190 mm)

Lower panel

1. Unplug ice maker or disconnect power.

2. Remove the two screws in the lower grille area and the

one screw from the center of the front panel support.

(Open bin door slightly for better access to screw.) Pull

the bottom forward and then pull down to remove the

lower access panel.

3. Remove the screws at each side of the top trim and

remove the top trim.

4. Carefully slide out the decorator panel and reassemble

with selected surface facing out.

NOTE: A custom panel should be

⁄4" (6 mm) thick and

17" x 11

⁄16" (433 mm x 303 mm). You may need to remove

the metal panels and spacers to allow room for the custom

panel thickness.

5. Replace the top trim and screws.

6. Reinstall the lower access panel.

7. Plug in ice maker or reconnect power.

ENGLISH

• Water will not enter the pump pan until the freezing plate

gets cold. Then the machine goes into a harvest cycle.

• Check for desired cube thickness. Adjust after 24 hours if

necessary. Best operation is obtained with ice thickness at

⁄2" (13 mm) to

⁄8" (16 mm).

Changing the door panels

Both Kenmore models 86485 and 86482 are equipped with

a double-sided decorator panel for both the bin door and the

lower access panel. The decorator panel is white on one side

and black on the other. The Kenmore model 86485 is also

equipped with a single-sided wood grain panel. You can

make custom panels to match your existing cabinet.

Bin door

1. Open the bin door and remove the two screws on the top

of the door. These screws hold the handle in place.

2. Loosen the screws in both side trim pieces.

3. Remove the handle as shown.

4. Carefully slide out the decorator panel and reassemble

with the selected surface facing out.

NOTE: Be careful not to scratch the panel as it is inserted.

5. Replace the handle. Tighten handle and trim piece screws.

NOTE: A custom panel should be

⁄4" (6 mm) thick and

17" x 13

⁄16" (433 mm x 335 mm). You need to break off the

ribs in the door insulation to allow room for the custom

panel thickness.

Screws

Handle

Screws

(both sides)

wWARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all panels before operating.

Failure to do so can result in death or

electrical shock.

Top trim

Front

panel

support

Screw

NORMAL

THICK

THIN

ICE

CLEAN

OFF

CYCLE

How the ice maker

makes ice

1. Water constantly circulates over a freezing plate. As the

water freezes into ice, minerals in the water are rejected.

This produces a clear sheet of ice with a low mineral content.

2. When the desired thickness is reached, the ice sheet is

released and slides onto a cutter grid. The grid divides the

sheet into individual cubes.

3. The water containing the rejected minerals is drained

after each freezing cycle.

4. Fresh water enters the unit for the next ice making

cycle.

5. Cubes fall into the storage bin. When the bin is full, the

ice maker shuts off automatically and restarts when

more ice is needed.

NOTE: A normal harvest cycle takes 1 to 2 minutes.

Things to remember

• Water enters only during the defrost cycle. Therefore, the

first cycle will be completed without water in the system.

• As the room and water temperatures vary, so will the

amount of ice produced. This means that higher operating

temperatures result in reduced ice production.

• The unit shuts off when ice in the storage bin touches the

bin thermostat. The unit will automatically cycle to keep the

storage bin full.

• The storage bin is not refrigerated and some melting will

occur. This varies with the room temperature.

• The unit needs good air circulation to perform efficiently.

Periodically clean the condenser and grille. If the ice maker

is located on a hard floor surface or there are pets in the

home the condensor should be cleaned every 4-6 weeks for

optimum performance.

• The water system needs to be cleaned periodically for good

circulation. See “Cleaning and sanitizing the ice making

system” section.

Setting the controls

1. Select ice thickness. The ice maker has been preset to

produce ice approximately

⁄2" (13 mm) thick, while operat-

ing in a room temperature of 70°F (21°C).

NOTE: Operation in different room temperatures may

require readjusting the Ice Thickness Control toward

THICK or THIN. Best performance is obtained with ice

⁄2"

(13 mm) to

⁄8" (16 mm) thick. If operating in a warm room

(above 90°F [32°C]), DO NOT set Ice Thickness Control to

the maximum thickness or the unit may malfunction.

2. To start normal ice making cycle, turn Cycle Control to ON.

3. To stop ice making cycle, turn Cycle Control to OFF.

4. The CLEAN setting is used whenever solutions are

circulated through the ice maker for cleaning. Only the

water pump operates at this setting. See “Cleaning and

sanitizing the ice making system” section.

Operating Instructions

Periodically inspect and clean the ice maker to keep it

operating at peak efficiency and to prevent premature failure

of system components.

Both the ice making system and the air-cooled condenser

need to be cleaned regularly. If the ice maker is located on a

hard floor surface or there are pets in the home the

condenser may require cleaning every 4-6 weeks for optimum

performance.

A dirty or clogged condenser prevents proper airflow, reduces

ice making capacity, and causes higher than recommended

operating temperatures which may lead to component failure.

All components of the ice maker are permanently lubricated

at the factory. They should not require any additional oiling

throughout the normal life of the machine.

Cleaning exterior surfaces

Wash the exterior enamel cabinet surfaces and gaskets with

warm water and mild soap or detergent. Rinse and dry.

Regular use of a good household-appliance cleaner and

wax will help protect the finish. Treat wood grain panels as

furniture.

NOTE: Do not use harsh or abrasive cleaners on the enamel

surfaces – they may scratch the finish.

Cleaning and sanitizing

the ice making system

The minerals rejected from the circulating water in the freez-

ing cycle will eventually form a hard, scaly deposit in the

water system which prevents the rapid release of ice.

Clean ice making system periodically to remove mineral scale

buildup. Frequency of cleaning depends on water hardness.

With soft water, cleaning may not be required for several

years. With hard water (15 to 20 grains/gal.), cleaning may be

required as often as every 6 months.

1. Turn Cycle Control to OFF.

2. Open bin door, remove the two thumb screws and slide

the ice cutter grid out of the two slots near the water pan.

3. Unplug the electrical harness. Any ice on the cutter grid

should be melted under running warm water. Attempting

to pick the ice slab from the grid may stretch and

damage the grid wires.

ENGLISH

General Cleaning and Care

4. Remove all ice from the storage bin and the freezing

plate.

5. Drain the water pan by removing the drain plug and then

replacing it.

6. Pour

⁄2 gallon (1.9 L) of hot tap water into the water pan

and turn the Cycle Control to CLEAN. This warms up the

system to make the cleaning solution more effective. Let

circulate for 5 minutes.

While tap water is circulating, prepare the cleaning

solution. Mix:

6 oz. (170 g) powdered citric or phosphoric acid

⁄2 gallon (1.9 L) hot water

(Citric and phosphoric acid crystals are available from

many pharmacies or scientific supply houses.)

NOTE: Commercial Ice Machine cleaners (liquid) are

also available from refrigeration parts supply stores.

Mix according to instructions on label (total quantity =

⁄2 gallon [1.9 L]).

7. Turn Cycle Control to OFF and drain tap water. (See

Step 5.)

8. Turn Cycle Control to CLEAN and slowly pour hot

cleaning solution into the water pan. If the solution

foams while pouring, wait until foaming stops. Then

add balance of solution.

Allow solution to circulate until the scale has dissolved

(15 to 30 minutes). Severe scale buildup may require

repeated cleaning with fresh cleaning solution.

NOTE: To clean scale off the freezing plate flanges of

the freezing plate, use rubber gloves and scrub with a

plastic scrubbing pad or non-soapfilled stainless steel

pad dipped in the cleaning solution.

9. Turn Cycle Control to OFF and drain the cleaning solu-

tion. Use rubber gloves when removing the drain plug.

10. Replace the drain plug and add

⁄2 gallon (1.9 L) of fresh

water into the water pan. Turn Cycle Control to CLEAN,

let circulate for 5 minutes, and drain. Repeat rinsing

process.

Electrical harness

Thumb screws (long)

Cutter grid

Freezing plate

flanges

Removing and cleaning the

interior components

1. Unplug ice maker or disconnect power.

2. Remove ice retainer baffle by flexing it to slide it off the

studs.

3. Remove the water pan by unscrewing the two thumb

screws.

Insert

into drain

Thumb

screws

(short)

Water pan

Drain

plug

Cleaning the condenser

1. Unplug ice maker or disconnect power.

2. Remove the two screws in the lower grille area and the

one screw from the center of the front panel support.

(Open bin door slightly for better access to the screw.)

3. Pull the bottom forward and then pull down to remove the

lower access panel.

4. Remove dirt and lint from the condenser fins with a soft

brush. Then use a vacuum cleaner with attachments to

remove the dirt from inside the unit compartment.

5. Replace the lower access panel and screws.

6. Plug in ice maker or reconnect power.

wWARNING

Electrical Shock Hazard

Disconnect power before cleaning.

Replace all panels before operating.

Failure to do so can result in death or

electrical shock.

Ice retainer

baffle

Thumb screws (long)

Cutter grid

front trim

wWARNING

Electrical Shock Hazard

Disconnect power before cleaning.

Replace all panels before operating.

Failure to do so can result in death or

electrical shock.

Screw

ENGLISH

4. Remove the hose from the water pump. Clean the water

inlet hose hanging in the water pan. Scrape off any mineral

deposits and then wash with mild soap or detergent in warm

water.

5. Remove the water distributor from the freezing plate. It

is held in place by rubber endcaps. Remove the inlet

hose and clean all water distributor holes and the small

orifice in the inlet side of the distributor. When replacing

the distributor, make sure the endcaps are located in the

freezing plate flange holes and that the water distributor

holes face down.

6. Wash the interior components you have just removed with

mild soap or detergent and warm water. Rinse in clean

water. Sanitize in a solution of 1 tablespoon (15 ml) of

household bleach mixed with 1 gallon (3.8 L) of warm

water.

NOTE: Do not wash plastic parts in the dishwasher.

Plastic parts cannot withstand temperatures above 145°F

(63°C).

Inlet hose

Water pump

7. Wash the storage bin, door, gasket, and ice scoop with

mild soap or detergent and warm water. Rinse with

clean water. Sanitize with the chlorine bleach and water

solution.

8. Replace the interior components (water distributor,

hoses, water pan, and ice retainer baffle).

9. Check the following:

• Hose from water valve is in water pan.

• Rubber drain plug is in water pan.

• Water distributor is seated and holes are facing

down.

• Hose is reconnected to pump and water distributor.

• Hose from water pan is inserted into storage bin

drain opening.

10. Reconnect electrical harness. Replace cutter grid and

thumb screws.

11. Plug in ice maker or reconnect power.

Filtering and treating

water

In most areas, it will be beneficial to filter or treat the water

being supplied to the ice machine. It can improve the

reliability of the machine, reduce water maintenance, and

produce the best quality of ice.

The installation of a polyphosphate feeder will generally

reduce scale buildup and the ice machine will require less

frequent cleaning.

Municipal water systems are generally treated with chlorine

to maintain a safe, potable water supply. Activated carbon

filters will sufficiently remove the residual chlorine from the

water and reduce surface staining of stainless steel materi-

als in the ice machine.

Freezing plate

holes

Inlet hose

Endcaps

Orifice

Freezing plate

Water distributor

Vacation and Moving Care

To shut down the ice maker:

1. Unplug ice maker or disconnect power.

2. Remove all ice from the storage bin.

3. Shut off the water supply.

4. Remove the two screws in the lower grille area and the

one screw from the center of the front panel support.

(Open bin door slightly for better access to the screw.) Pull

the bottom forward and then pull down to remove the lower

access panel.

wWARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all panels before operating.

Failure to do so can result in death or

electrical shock.

Screw

5. Disconnect the inlet and outlet lines to the water valve.

Allow these lines to drain and then reconnect them to the

valve.

6. Replace the lower access panel and screws.

7. Remove water from the drain lines and drain the water pan

if the unit will be subjected to freezing temperatures during

shutdown.

8. Before using again, clean and sanitize the ice maker and

storage bin.

9. Plug in ice maker or reconnect power.

Inlet

Outlet

Water

valve

ENGLISH

Before Calling for Service

Self-service checklist

Performance problems often result from little things you can

find and fix yourself. Check the list below. It could save you

the cost of a service call.

Unit does not run:

• Cycle Control must be in the ON position.

• Check to see that the power cord is plugged in.

• Check for blown household fuse or tripped circuit breaker.

• Room temperatures must be above 55°F (13°C).

Otherwise, the bin thermostat may sense a cold room

temperature and shut off even though bin is not full of

ice. Also, unit may not restart once it does shut down.

Unit runs but produces no ice:

• Cycle Control must be in the ON position.

• Check water supply to make sure it is open.

• If ice maker is to be operated at an elevation of 2,000 feet

(600 m) or more above sea level, both the Bin Thermostat

and the Ice Thickness Thermostat will need to be

recalibrated. Call your dealer or an authorized service

group to have the necessary changes made.

Unit runs but produces very little ice:

• Room temperature may be extremely high – over 90°F

(32°C). In this case, it is normal for ice production to

be low.

• Dirt or lint may be blocking the airflow through the finned

condenser. Condenser needs to be cleaned.

• Check to see if the unit has a scale buildup in the water

and freezing system. Clean, if necessary.

Cutter grid is not cutting ice sheets:

• Check the grid harness plug to make sure the connection

is secure.

Off-taste in ice cubes:

• There may be an unusually high mineral content in your

water supply. Water may need to be filtered.

• Do not store any foods in the storage bin.

• Make sure all packaging materials have been removed.

Notes

Garantía

UN AÑO DE GARANTÍA

COMPLETA

Durante un año a partir de la fecha de compra, si se usa la

fábrica de hielo para fines domésticos, haciéndola funcionar

y manteniéndola de acuerdo con las instrucciones

suministradas o que vienen con ella, Sears reparará la

fábrica de hielo, sin cargo, si tiene defectos de materiales

o de fabricación.

UN AÑO DE GARANTÍA

LIMITADA

Durante un año a partir de la fecha de compra, si se usa la

fábrica de hielo para fines comerciales, haciéndola funcionar

y manteniéndola de acuerdo con las instrucciones

suministradas o que vienen con ella, Sears proveerá, sin

cargo, las piezas de repuesto que tengan defecto de

materiales o de fabricación. Usted pagará la mano de obra.

GARANTÍA COMPLETA DE

CINCO AÑOS PARA EL

SISTEMA DE REFRIGERACIÓN

SELLADO

Durante cinco años a partir de la fecha de compra, siempre

que el funcionamiento y el mantenimiento del producto se

haga de acuerdo con las instrucciones suministradas o que

vienen con el mismo, Sears reparará el sistema sellado (que

consiste en: refrigerante, tuberías de conexión y el motor

compresor), sin cargo, si tuviera defectos de

materiales o de fabricación.

Esta garantía le otorga derechos específicos, y es posible

que usted tenga también otros derechos, los cuales varían

de un estado al otro.

EL SERVICIO DE REPARACIÓN DE LA GARANTÍA ESTÁ

A SU DISPOSICIÓN AL PONERSE EN CONTACTO CON

EL CENTRO DE SERVICIO SEARS O EL ESTABLECIMIEN-

TO SEARS MÁS CERCANO EN LOS ESTADOS UNIDOS.

Sears, Roebuck and Co. • D/817 WA • Hoffman Estates, IL 60179

ANOTE AQUÍ LOS NÚMEROS DE MODELO Y DE SERIE.

Cuando necesite el servicio, o llame para consultar, tenga la

siguiente información a mano:

Número de Modelo

Número de Serie

Fecha de Compra

Centro de Servicio Sears y número de teléfono

ESPAÑOL

ÍNDICE

Página

Garantía..........................................................................15

Seguridad de la fábrica de hielo..................................16

Partes y características................................................16

Instrucciones para la instalación ................................17

Requisitos eléctricos.................................................17

Requisitos de espacio...............................................17

Diagramas del cableado de la unidad......................18

Instalación de la fábrica de hielo..............................18

Control del funcionamiento.......................................19

Cambio de los paneles de la puerta.........................20

Instrucciones de funcionamiento................................21

Forma en que la fábrica produce el hielo.................21

Puntos para recordar ...............................................21

Ajuste de los controles..............................................21

Limpieza y cuidado general.........................................22

Limpieza de las superficies exteriores......................22

Limpieza e higiene del sistema

de elaboración de hielo.............................................22

Limpieza del condensador........................................23

Desmontaje y limpieza de las piezas interiores .......23

Filtrado y tratamiento del agua.................................24

Cuidados para las vacaciones y las mudanzas.........25

Antes de llamar al servicio...........................................26

Números de Sears para llamadas gratuitas...............40

Su seguridad y la seguridad de los demás es muy importante.

Hemos incluido muchos mensajes importantes de seguridad en este manual y en su electrodoméstico. Lea

y obedezca siempre todos los mensajes de seguridad.

Este es el símbolo de advertencia de seguridad.

Este símbolo le llama la atención sobre peligros que pueden ocasionar la muerte o una lesión

a usted y a los demás.

Todos los mensajes de seguridad irán precedidos por el símbolo de advertencia de seguridad

y la palabra “PELIGRO” o “ADVERTENCIA”. Estas palabras significan:

Seguridad de la fábrica de hielo

CONSERVE ESTAS INSTRUCCIONES

Si no sigue las instrucciones, usted morirá o sufrirá

una lesión grave.

Si no sigue las instrucciones, usted puede morir o

sufrir una lesión grave.

Todos los mensajes de seguridad identificarán el peligro, le informarán cómo reducir las posibilidades de sufrir una

lesión y lo que puede suceder si no siguen las instrucciones.

wPELIGRO

wADVERTENCIA

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

ADVERTENCIA:

Para reducir el riesgo de incendio, choque eléctrico o lesiones personales al usar la fábrica

de hielo siga estas precauciones básicas:

• Conecte a un contacto de pared de conexión a tierra

de 3 terminales.

• No quite el terminal de conexión a tierra.

• No use un adaptador.

• No use un cable eléctrico de extensión.

• Desconecte el suministro de energía antes de limpiarlo.

• Desconecte el suministro de energía antes de darle

servicio.

• Vuelva a colocar todos los paneles antes de hacer

funcionar.

• Use dos o más personas para mover e instalar la

fábrica de hielo.

Partes y características

Placa con el

número de

modelo y de

serie

(en la pestaña

interior izquierda

del aparato)

Placa

contenedora

de hielo

Panel de acceso

inferior

Perilla de

control del

ciclo

Perilla de

control del

grosor del

hielo

Cajón del

hielo

Pala para el

hielo

ESPAÑOL

Requisitos eléctricos

Se requiere un circuito de suministro eléctrico con fusibles de

15 amperios, 115 V, 60 Hz, CA solamente, conectado ade-

cuadamente a tierra de acuerdo con las Normas para

Instalaciones Eléctricas y con las normas y ordenanzas

locales.

Se recomienda tener un circuito separado que sirva sola-

mente para este electrodoméstico. Use un receptáculo que no

pueda ser desconectado con un interruptor o con un conmu-

tador a cadena.

NOTA: Se recomienda el empleo de un fusible retardador

o cortacircuitos.

Método para la conexión a tierra

Para su seguridad personal, este electrodoméstico debe estar

conectado a tierra. Está equipado con un cable eléctrico que

tiene un enchufe de tres terminales con conexión a tierra.

Para reducir el peligro de posibles choques eléctricos, el

cable debe ser enchufado en un contacto de pared que tenga

tres terminales con conexión a tierra, de acuerdo con las

Normas para Instalaciones Eléctricas y con los códigos y

ordenanzas locales. Si no hubiera un contacto adecuado, el

usuario tiene la responsabilidad de contratar a un electricista

calificado para instalar un contacto de pared apropiado que

tenga tres terminales con conexión a tierra.

Contacto de pared

de conexión a tierra

de 3 terminales

Terminal para

conexión a tierra

Instrucciones para la instalación

Requisitos de espacio

• Para asegurar la ventilación adecuada de su fábrica de

hielo, la parte del frente debe mantenerse completamente

libre de obstrucciones. La parte superior y los tres lados de

la unidad pueden estar cerrados, pero la instalación debe

ser hecha de manera que la fábrica de hielo pueda ser

movida hacia adelante para hacerle el servicio, si fuera

necesario.

• La instalación de la fábrica de hielo requiere una entrada de

suministro de agua fría con tubos de cobre blando de

⁄4 de

pulgada (6 mm) de diámetro exterior y una válvula de cierre,

así como también un sistema de desagüe por gravedad o

una bomba condensadora para llevar el agua a un desagüe

ya existente.

• Elija un área bien ventilada con temperaturas por encima de

los 55°F (13°C) y por debajo de los 110°F (43°C). Los

mejores resultados se logran con temperaturas entre 70°F

(21°C) y 90°F (32°C). Esta unidad DEBE ser instalada en

un área protegida de los elementos tales como el viento, llu-

via, rocío de agua o goteras.

• Cuando instale la fábrica de hielo debajo de un mostrador,

siga las dimensiones de abertura recomendadas que se

muestran a continuación.

NOTA: No deje que el cable eléctrico se tuerza o quede

atrapado entre la fábrica de hielo y el gabinete.

Dimensiones del espacio de empotrado

⁄2"

(88 cm)

90°

9" máx

(23 cm)

18" (46 cm)

⁄2" (11.5 cm) A

la línea central

Coloque la

salida dentro

de este

espacio

wADVERTENCIA

Peligro de Choque Eléctrico

Conecte a un contacto de pared de conexión a

tierra de 3 terminales.

No quite el terminal de conexión a tierra.

No use un adaptador.

No use un cable eléctrico de extensión.

No seguir estas instrucciones puede ocasionar

la muerte, incendio o choque eléctrico.

Diagramas del cableado de

la unidad

Este modelo funciona con 115V, exceptuando el circuito de la

rejilla de corte que funciona con 8,5V y 1 Amp. El amperaje

máximo del fusible usado debe ser 15 Amp.

El compresor funciona en todo momento exceptuando el

momento en que el termostato lo interrumpe. Esto desactiva

todo el sistema excepto el transformador y la rejilla de corte.

Bajo condiciones normales de funcionamiento, cuando el

evaporador alcanza la temperatura preestablecida (de 10°F

[-12°C] a -3°F [-19°C], dependiendo del espesor del hielo), el

termostato evaporador se abre apagando el motor del

ventilador y el de la bomba. El solenoide de gas caliente y el

solenoide de la válvula de agua permanecen activados en

este momento y permanecen así hasta que el evaporador

alcance los 38°F (3°C).

CLEAN

OFF

SERVICE

SWITCH

8.5 V

115 V

GRID

TRANSFORMER

COMPRESSOR

START RELAY

OVERLOAD

WATER PUMP

CONDENSER

FAN

115 VOLTS

60 HERTZ

BIN

THERMOSTAT

EVAPORATOR

THERMOSTAT

L N

HOT GAS

SOL

W Y

CUTTER

WATER

VALVE

SOL

BK / W

BIN

THERMO

EVAP

THERMO

SERVICE

SWITCH

BK/ W

MOT

PUMP

GRID

115 V

60 HZ

1 PH

FAN

COMPRESSOR

WATER

HOT GAS

SOL

N.C.

SOL

N.C.

START

RELAY

OVERLOAD

PLUG

115V

TRANS

OROR

G/Y

CAB

SHELF

CABINET

8.5V

CONTROL

BRACKET

MOT

CUADRO DE COLORES

R Rojo

BK Negro

BL Azul

W Blanco

Y Amarillo

OR Naranja

BK/W Trazador de

Negro/Blanco

G/Y Trazador de

Verde/Amarillo

SYMBOL CODE

CONNECTOR - SCREW ON

CONNECTOR - CLOSED END

DISCONNECT TERMINAL

PERMANENT CONNECTION

PLUG CONNECTOR

GROUND (CHASSIS)

ADVERTENCIA

Peligro de Choque Eléctrico

Desconecte el suministro de energía antes de darle

servicio.

Vuelva a colocar todos los paneles antes de hacer

funcionar.

No seguir estas instrucciones puede ocasionar

la muerte o choque eléctrico.

= CONECTADOR – PARA ATORNILLAR

= CONECTADOR – EXTREMO CERRADO

= DESCONECTE EL TERMINAL

= CONEXIÓN PERMANENTE

= CONECTADOR DEL ENCHUFE

= TOMA DE TIERRA (CHASIS)

CÓDIGO DE SÍMBOLOS

wADVERTENCIA

Peligro de Peso Excesivo

Use dos o más personas para mover e instalar

la fábrica de hielo.

No seguir esta instrucción puede ocasionar

una herida a la espalda u otra herida.

Instalación de la fábrica de

hielo

Preparación de la fábrica de hielo

1. Quite el panel inferior de acceso. Quite los tornillos que

fijan la rejilla a la parte de abajo y un tornillo en el centro

del soporte del panel del frente y levántelo sacándolo del

aparato.

Tornillo

/4"

/8"

/4"

Conexión con el desagüe

(cumpla con los códigos locales)

1. La unidad tiene un sistema de desagüe por gravedad.

2. La instalación ideal tiene un tubo de circulación (de 1

⁄4

pulgs. [32 cm] como mínimo) puesto directamente por

debajo de la salida del tubo de desagüe.

3. Quizás sea preferible aislar bien la tubería de desagüe

hasta la entrada del drenaje.

4. Vuelva a colocar el panel de acceso inferior y los

tornillos.

5. Enchufe la unidad en un contacto de pared de conexión a

tierra de 3 terminales.

Método alternativo:

Si no se dispone de una conexión de desagüe directamente

ubicada debajo de la salida de la tubería de desagüe,

instale en el compartimiento posterior de la fábrica de hielo

una bomba de desagüe listada en la UL.

Especificaciones para la bomba de desagüe:

• Debe estar listada en la UL y tener un cable de 120 VCA,

de 3 alambres y con conexión a tierra.

•

Las dimensiones exteriores totales (máximas) son: 15 pulgs.

(38 cm) de ancho x 6 pulgs. (15 cm) de profundidad x 9

⁄2

pulgs. (24 cm) de altura.

• Gasto de la bomba (mínimo): 0,4 gpm a 12 pies de altura.

• Escala de temperaturas de funcionamiento: 55° F a 110° F.

Control del funcionamiento

• Haga funcionar la unidad poniendo el Control del Ciclo en la

posición “ON” y abriendo la válvula de la tubería de agua.

NOTA: La izquierda es “OFF” (apagado) – la mitad es “ON”

(encendido) y la derecha es “CLEAN” (limpieza). En la posi-

ción “CLEAN” solamente funciona la bomba de agua.

ESPAÑOL

/8"

/2"

/32"

2. Haga girar a mano el ventilador para asegurarse de que se

mueva libremente.

3. Afloje algo los tornillos de mariposa que sostienen la rejilla

de corte y la bandeja de agua para facilitar la limpieza e

higienización del sistema de agua. Vea la sección

“Desmontaje y limpieza de las piezas interiores”

Conexión del agua

(cumpla con los códigos locales)

1. Utilice tuberías de cobre blando de

⁄4 de pulg. (6 mm) de

diámetro exterior para el suministro de agua fría.

2. Ponga en la tubería de agua una válvula de cierre manual

adecuada. No use válvulas perforadoras ni las de tipo de

montura de

⁄16 de pulg. porque reducen la corriente de

agua y se atascan con más facilidad.

NOTA: Siempre purgue las tuberías de agua antes de

hacer la conexión final con la válvula de entrada de agua

para prevenir el posible mal funcionamiento de la válvula

de agua.

3. Coloque la tubería de manera que entre en el orificio de

acceso localizado en el lado derecho de la parte trasera

del aparato. Cuando se empuja el aparato hacia atrás para

dejarlo en su posición, la tubería debe sobresalir del frente

del mismo.

NOTA: Luego de poner el aparato en su lugar doble la

tubería para unirla con la conexión en la válvula de agua.

El accesorio de manguera de compresión con rosca se

encuentra en la bolsa de accesorios debajo de la pala de

hielo. Este acoplamiento ofrece un medio conveniente de

desconexión cuando se hace el servicio. Asegúrese de que

la tubería no toque al compresor para evitar ruidos

molestos.

Nivelación de la fábrica de hielo

1. Luego de colocar la unidad en la posición deseada, com-

pruebe que el lado derecho y el izquierdo, el frente y la

parte de atrás estén nivelados. La nivelación precisa es

muy importante para que funcione adecuadamente.

2. La unidad debe estar calzada de manera de que esté firme

y nivelada. Las calzas deben ser de un material duro y

resistente.

3. Si el código de higiene lo requiere, selle el aparato al piso

con un compuesto de enmasillado aprobado, luego de

haber hecho todas las conexiones eléctricas y las de agua.

Vista lateral derecha

⁄4" (19 mm)

⁄8"

(606 mm)

Vista posterior

⁄8"

(200 mm)

⁄4"

(95 mm)

⁄2"

(190 mm)

(229 mm)

(76 mm)

⁄32"

(874 mm)

⁄2"

(190 mm)

⁄2"

(38 mm)

Accesorio de

compresión de la

tubería de agua de

⁄4 de pulg. (6 mm)

de diámetro

exterior, en la

válvula de agua.

Doble la tubería

de agua de

suministro local

para conectarla

con el acople

de la válvula de

agua

Válvula

solenoide

de la

entrada

de agua

Orificio de

acceso de la

tubería de agua

de suministro

local.

Tubo de desagüe

de goma al

drenaje abierto,

de 4 pulgs.

(102 mm) de

longitud,

⁄8 de

pulg. (16 mm) de

diámetro interior

Tubo de

circulación con

un diámetro

mínimo de 1

⁄4

pulgs. (32 mm)

Tubo de

desagüe

continúa en la página siguiente

Panel inferior

1. Desenchufe la fábrica de hielo o desconecte la electricidad.

2. Quite los dos tornillos del área inferior de la rejilla y el

tornillo del centro del soporte del panel del frente. (Abra

ligeramente la puerta del cajón para lograr mejor acceso al

tornillo.) Tire de la parte inferior hacia adelante y luego

hacia abajo para quitar el panel de acceso inferior.

3. Quite los tornillos que están a cada lado del ribete superior

y quítelo.

4. Con cuidado deslice el panel decorativo para quitarlo y

vuelva a montarlo con la superficie elegida hacia afuera.

NOTA: El panel hecho a pedido especial debe tener

⁄4 de pulg. (6 mm) de espesor y 17 pulgs. x 11

⁄16 pulgs.

(433 mm x 303 mm). Es posible que tenga que quitar los

paneles de metal y los espaciadores para dejarle lugar al

panel hecho a pedido especial.

5. Vuelva a colocar el ribete superior con los tornillos.

6. Vuelva a instalar el panel de acceso inferior.

7. Enchufe la fábrica de hielo o vuelva a conectar la electricidad.

ADVERTENCIA

Peligro de Choque Eléctrico

Desconecte el suministro de energía antes de darle

servicio.

Vuelva a colocar todos los paneles antes de hacer

funcionar.

No seguir estas instrucciones puede ocasionar

la muerte o choque eléctrico.

Ribete

superior

Soporte del

panel del

frente

• Use una linterna para observar el espacio que está entre la

rejilla de corte y el revestimiento para controlar que haya un

flujo de agua parejo sobre la placa congeladora. La unidad

debe estar nivelada para que funcione adecuadamente.

• El agua no entrará a la bandeja de la bomba hasta que la

placa congeladora se enfríe. Luego la máquina ingresa al

ciclo de cosecha.

• El mejor rendimiento se obtiene con un espesor de hielo de

⁄2 pulg. (13 mm) hasta

⁄8 de pulg. (16 mm).

Cambio de los paneles de

la puerta

Ambos modelos de Kenmore, el 86485 y el 86482 vienen

equipados con paneles decorativos de dos frentes para la

puerta del cajón y el acceso inferior. El panel decorativo es

blanco de un lado y negro del otro. El modelo 86485 de

Kenmore está también equipado con un panel de madera de

un lado. Usted puede adquirir también paneles hechos por

encargo para que hagan juego con los demás muebles.

Puerta del cajón

1. Abra la puerta del cajón y quite los dos tornillos de la parte

superior de la puerta. Estos tornillos fijan la manija de la

puerta.

2. Afloje los tornillos de los dos ribetes laterales.

3. Quite la manija según se muestra.

4. Con cuidado deslice el panel decorativo hasta quitarlo y

vuélvalo a montar con la superficie elegida hacia afuera.

NOTA: Tenga cuidado de no rayar el panel cuando lo

inserte.

5. Vuelva a colocar la manija. Apriete los tornillos de la manija

y de los ribetes.

NOTA: El panel hecho a pedido especial debe tener

⁄4 de

pulg. (6 mm) de espesor y 17 pulg. x 13

⁄16 pulgs. (433 mm

x 335 mm). Debe quitar las varillas de la aislación de la

puerta para darle lugar al espesor del panel hecho a

pedido especial.

Tornillo

Tornillos

Manija

Tornillos

(en los

dos lados)

La page charge ...

Kenmore 86485 Manuel utilisateur

Marque: Kenmore

Modèle: 86485

Taper: Manuel utilisateur

Ce manuel convient également à

86482

Télécharger le PDF

rapport

dans d''autres langues

English: Kenmore 86485 User manual
español: Kenmore 86485 Manual de usuario

Kenmore 86485 Manuel utilisateur

Ce manuel convient également à

Kenmore 86485 Manuel utilisateur

dans d''autres langues

Documents connexes