Hitachi DV 14DV Safety And Instruction Manual

Marque: Hitachi

Modèle: DV 14DV

Catégorie: Perceuses mixtes sans fil

Taper: Safety And Instruction Manual

Ce manuel convient également à

INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI

AVERTISSEMENT

Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner

la mort ou de sérieuses blessures corporelles!

Ce mode d’emploi contient d’importantes informations à propos de la sécurité de

ce produit. Prière de lire et de comprendre ce mode d’emploi AVANT d’utiliser

l’outil motorisé. Garder ce mode d’emploi à la disponibilité des autres utilisateurs

et propriétaires avant qu’ils utilisent l’outil motorisé. Ce mode d’emploi doit être

conservé dans un endroit sûr.

SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL

WARNING

IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily

injury!

This manual contains important information about product safety. Please read

and understand this manual BEFORE operating the power tool. Please keep this

manual available for other users and owners before they use the power tool. This

manual should be stored in safe place.

INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES

ADVERTENCIA

¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede

resultar en lesiones de gravedad o la muerte!

Este manual contiene información importante sobre la seguridad del producto.

Lea y comprenda este manual ANTES de utilizar la herramienta eléctrica. Guarde

este manual para que puedan leerlo otras personas antes de utilizar la herramienta

eléctrica. Este manual debe ser guardado en un lugar seguro.

DV 14DV• DV 18DV

MODEL Variable speed CORDLESS HAMMER DRILL

MODÈLE

MARTEAU PERFORATEUR À BATTERIE

MODELO

MARTILLO ROTO-PERCUTOR A BATERÍA

DV14DV•DV18DV-E.E65 6/21/02, 5:06 PM1

CONTENTS

English

Page

IMPORTANT INFORMATION ............................. 3

MEANINGS OF SIGNAL WORDS....................... 3

SAFETY .................................................................... 4

GENERAL SAFETY RULES – FOR ALL

BATTERY OPERATED TOOLS ..................... 4

SPECIFIC SAFETY RULES AND SYMBOLS ....... 6

IMPORTANT SAFETY INSTRUCTIONS

FOR BATTERY CHARGER ............................ 8

IMPORTANT SAFETY INSTRUCTIONS

FOR USE OF THE BATTERY AND

BATTERY CHARGER .................................... 9

DISPOSAL OF THE EXHAUSTED BATTERY ... 10

FUNCTIONAL DESCRIPTION ................................ 11

MODEL ............................................................... 11

NAME OF PARTS .............................................. 11

SPECIFICATIONS .............................................. 12

Page

ASSEMBLY AND OPERATION ............................. 13

APPLICATIONS.................................................. 13

REMOVAL AND INSTALLATION METHOD

OF BATTERY .................................................. 13

CHARGING METHOD........................................ 13

BEFORE USE ..................................................... 15

OPERATION ....................................................... 16

THE SCOPE AND SUGGESTIONS

FOR USES ...................................................... 19

HOW TO SELECT TIGHTENING TORQUE ....... 20

MAINTENANCE AND INSPECTION ..................... 21

ACCESSORIES ....................................................... 22

STANDARD ACCESSORIES ............................. 22

OPTIONAL ACCESSORIES ............................... 23

TABLE DES MATIERES

Français

Page

INFORMATIONS IMPORTANTES ........................... 24

SIGNIFICATION DES MOTS D’AVERTISSEMEN

T ........ 24

SECURITE ................................................................ 25

REGLES GENERALES DE SECURITE – POUR TOUS

LES OUTILS FONCTIONNANT SUR BATTERIE

.... 25

REGLES DE SECURITE SPECIFIQUES ET SYMBOLES

.. 27

CONSIGNES DE SÉCURITÉ IMPORTANTES

POUR L’UTILISATION DU CHARGEUR DE BATTERIE ....

CONSIGNES DE SÉCURITÉ IMPORTANTES

POUR L’UTILISATION DE LA BATTERIE ET DU CHARGEUR

DE BATTERIE

.................................................. 30

MISE AU REBUT D’UNE BATTERIE USÉE ........ 31

DESCRIPTION FONCTIONNELLE ........................... 32

MODELE ............................................................... 32

NOM DES PARTIES ............................................. 32

SPECIFICATIONS ................................................ 33

Page

ASSEMBLAGE ET FONCTIONNEMENT ..........................

UTILISATIONS ..................................................... 34

MÉTHODE DE RETRAIT ET D’INSTALLATION

DE LA BATTERIE .......................................... 34

MÉTHODE DE RECHARGE ................................. 34

AVANT L’UTILISATION ...................................... 37

UTILISATION ....................................................... 37

PLAGE D’UTILISATION ET SUGGESTIONS ...... 41

SÉLECTION DU COUPLE DE SERRAGE ............ 41

ENTRETIEN ET INSPECTION .................................. 43

ACCESOIRES ........................................................... 44

ACCESSOIRES STANDARD ............................... 44

ACCESSOIRES EN OPTION ................................ 45

ÍNDICE

Español

Página

INFORMACIÓN IMPORTANTE ............................... 46

IGNIFICADO DE LAS PALABRAS DE SEÑALIZACIÓN

........ 46

SEGURIDAD ............................................................. 47

NORMAS GENERALES DE SEGURIDAD – PARA TODAS

LAS HERRAMIENTAS ALIMENTADAS CON BATERÍA

.. 47

NORMAS Y SÍMBOLOS ESPECÍFICOS DE

SEGURIDAD ................................................. 49

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

PARA EL CARGADOR DE BATERÍAS

.................. 51

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

PARA LA BATERÍA Y EL CARGADOR DE BATERÍAS

... 52

ELIMINACIÓN LAS BATERÍAS AGOTADAS ..... 53

DESCRIPCIÓN FUNCIONAL .................................... 54

MODELO .............................................................. 54

NOMENCLATURA ............................................... 54

ESPECIFICACIONES ............................................ 55

Página

MONTAJE Y OPERACIÓN....................................... 56

APLICACIONES ................................................... 56

MÉTODO DE EXTRACCIÓN E INSTALACIÓN

DE LA BATERÍA ............................................ 56

MÉTODO DE CARGA .......................................... 56

ANTES DE LA UTILIZACIÓN .............................. 59

OPERACIÓN ......................................................... 59

ALCANCE Y SUGERENCIAS PARA LA

UTILIZACIÓN ................................................ 62

FORMA DE SELECCIONAR EL PAR DE APRIETE .......

MANTENIMIENTO E INSPECCIÓN ........................ 64

ACCESORIOS ........................................................... 65

ACCESORIOS ESTÁNDAR .................................. 65

ACCESORIOS OPCIONALES .............................. 66

DV14DV•DV18DV-E.E65 6/21/02, 5:06 PM2

English

IMPORTANT SAFETY INFORMATION

Read and understand all of the safety precautions, warnings and operating instructions in

the Instruction Manual before operating or maintaining this power tool.

Most accidents that result from power tool operation and maintenance are caused by the

failure to observe basic safety rules or precautions. An accident can often be avoided by

recognizing a potentially hazardous situation before it occurs, and by observing appropriate

safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual and

in the sections which contain the operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identified by

WARNINGS on the power tool and in this Instruction Manual.

NEVER use this power tool in a manner that has not been specifically recommended by

HITACHI.

MEANINGS OF SIGNAL WORDS

WARNING indicates a potentially hazardous situation which, if ignored, could result in death

or serious injury.

CAUTION indicates a potentially hazardous situation which, if not avoided, may result in

minor or moderate injury, or may cause machine damage.

NOTE emphasizes essential information.

DV14DV•DV18DV-E.E65 6/21/02, 5:06 PM3

English

SAFETY

GENERAL SAFETY RULES – FOR ALL BATTERY OPERATED TOOLS

WARNING: Read and understand all instructions.

Failure to follow all instructions listed below, may result in electric shock,

fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

1. Work Area

(1) Keep your work area clean and well lit. Cluttered benches and dark areas invite

accidents.

(2) Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases, or dust. Power tools create sparks which may ignite the

dust of fumes.

(3) Keep bystanders children, and visitors away while operating a power tool.

Distractions can cause you to lose control.

2. Electrical Safety

(1) A battery operated tool with integral batteries or a separate battery pack must be

recharged only with the specified charger for the battery.

A charger that may be suitable for one type of battery may create a risk of fire when

used with another battery.

(2) Use battery operated tool only with specifically designed battery pack.

Use of any other batteries may create a risk of fire.

3. Personal Safety

(1) Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use tool while tired or under the influence of drugs, alcohol, or

medication. A moment of inattention while operating power tools may result in

serious personal injury.

(2) Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your

hair, clothing and gloves away from moving parts. Loose clothes, jewelry, or long hair

can be caught in moving parts.

(3) Avoid accidental starting. Be sure switch is in off position before inserting battery.

Carrying tools with your finger on the switch or inserting the battery pack into a tool

that have the switch on invites accidents.

(4) Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that

is left attached to a rotating part of the tool may result in personal injury.

(5) Do not overreach. Keep proper footing and balance at all times. Proper footing and

balance enable better control of the tool in unexpected situations.

(6) Use safety equipment. Always wear eye protection. Dust mask, non-skid safety

shoes, hard hat, or hearing protection must be used for appropriate conditions.

DV14DV•DV18DV-E.E65 6/21/02, 5:06 PM4

English

4. Tool Use and Care

(1) Use clamps or other practical way to secure and support the workpiece to a stable

platform. Holding the work by hand or against your body is unstable and may lead to

loss of control.

(2) Do not force tool. Use the correct tool for your application. The correct tool will do

the job better and safer at the rate for which it is designed.

(3) Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled

with the switch is dangerous and must be repaired.

(4) Disconnect battery pack from tool or place the switch in the locked or off position

before making any adjustments, changing accessories, or storing the toos. Such

preventive safety measures reduce the risk of starting the tool accidentally.

(5) Store idle tools out of reach of children and other untrained persons. Tools are

dangerous in the hands of untrained users.

(6) When battery pack is not in use, keep it away from other metal objects like: paper

clips, coins, keys, nails, screws, or other small metal objects that can make a

connection from one terminal to another.

Shorting the battery terminals together may cause sparks, burns, or a fire.

(7) Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained

tools, with sharp cutting edges are less likely to bind and are easier to control.

(8) Check for misalignment or binding of moving parts, breakage of parts, and any other

condition that may affect the tools operation. If damaged, have the tool serviced by

a HITACHI authorized service center before using. Many accidents are caused by

poorly maintained tools.

(9) Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one tool, may become hazardous when used on

another tool.

5. Service

(1) Tool service must be performed only by a HITACHI authorized service center. Service

or maintenance performed by unqualified personnel could result in a risk of injury.

(2) When servicing a tool, use only identical replacement parts. Follow instructions in

the Maintenance section of this manual. Use of unauthorized parts or failure to follow

Maintenance Instruction may create a risk of electric shock or injury.

WARNING:

Some dust created by power sanding, sawing, grinding, drilling, and other construction

activities contains chemicals known to the State of California to cause cancer, birth defects

or other reproductive harm. Some examples of these chemicals are:

● Lead from lead-based paints,

● Crystalline silica from bricks and cement and other masonry products, and

● Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work.

To reduce your exposure to these chemicals: work in a well ventilated area, and work with

approved safety equipment, such as those dust masks that are specially designed to filter

out microscopic particles.

DV14DV•DV18DV-E.E65 6/21/02, 5:06 PM5

English

SPECIFIC SAFETY RULES AND SYMBOLS

1. Hold tools by insulated gripping surfaces when performing an operation where the

cutting tool may contact hidden wiring. Contact with a “live” wire will make exposed

metal parts of the tool “live” and shock the operator.

2. ALWAYS wear ear plugs when using the tool for extended periods.

Prolonged exposure to high intensity noise can cause hearing loss.

3. NEVER place hands or other body parts near the drill bit or chuck during operation. Hold

the drill by its handle only.

4. Because the cordless hammer drill operates by battery power, be aware of the fact that

it can begin to operate at any time.

5. When working at elevated locations, clear the area of all other people and be aware of

conditions below you.

6. NEVER touch moving parts.

NEVER place your hands, fingers or other body parts near the tool’s moving parts.

7. NEVER operate without all guards in place.

NEVER operate this tool without all guards or safety features in place and in proper

working order. If maintenance or servicing requires the removal of a guard or safety

feature, be sure to replace the guard or safety feature before resuming operation of the

tool.

8. Use right tool.

Don’t force small tool or attachment to do the job of a heavy-duty tool.

Don’t use tool for purpose not intended —for example— don’t use circular saw for

cutting tree limbs or logs.

9. NEVER use a power tool for applications other than those specified.

NEVER use a power tool for applications other than those specified in the Instruction

Manual.

10. Handle tool correctly.

Operate the tool according to the instructions provided herein. Do not drop or throw the

tool. NEVER allow the tool to be operated by children, individuals unfamiliar with its

operation or unauthorized personnel.

11. Keep all screws, bolts and covers tightly in place.

Keep all screws, bolts, and plates tightly mounted. Check their condition periodically.

12. Do not use power tools if the plastic housing or handle is cracked.

Cracks in the tool’s housing or handle can lead to electric shock. Such tools should not

be used until repaired.

13. Blades and accessories must be securely mounted to the tool.

Prevent potential injuries to youself or others. Blades, cutting implements and accessories

which have been mounted to the tool should be secure and tight.

DV14DV•DV18DV-E.E65 6/21/02, 5:06 PM6

English

14. NEVER use a tool which is defective or operating abnormally.

If the tool appears to be operating unusually, making strange noises, or otherwise

appears defective, stop using it immediately and arrange for repairs by a Hitachi

authorized service center.

15. Carefully handle power tools.

Should a power tool be dropped or struck against hard materials inadvertently, it may

be deformed, cracked, or damaged.

16. Do not wipe plastic parts with solvent.

Solvents such as gasoline, thinner benzine, carbon tetrachloride, and alcohol may

damage and crack plastic parts. Do not wipe them with such solvents.

Wipe plastic parts with a soft cloth lightly dampened with soapy water and dry

thoroughly.

17. ALWAYS wear eye protection that meets the requirement of the latest revision of ANSI

Standard Z87.1.

18. Definitions for symbols used on this tool

............

volts

—

---

...........

direct current

..........

no load speed

---/min

...

revolutions per minute

DV14DV•DV18DV-E.E65 6/21/02, 5:06 PM7

English

IMPORTANT SAFETY INSTRUCTIONS

FOR BATTERY CHARGER

1. This manual contains important safety and operating instructions for battery charger

Model UC24YFA/UC24YF.

2. Before using battery charger, read all instructions and cautionary markings on (1) battery

charger, (2) battery, and (3) product using battery.

3. To reduce risk of injury, charge HITACHI rechargeable battery type EB7, EB9, EB12, EB14,

EB18 series and EB24B. Other type of batteries may burst causing personal injury and

damage.

4. Do not expose battery charger to rain or snow.

5. Use of an attachment not recommended or sold by the battery charger manufacturer may

result in a risk of fire, electric shock, or injury to persons.

6. To reduce risk of damage to electric plug and cord, pull by plug when disconnecting

battery charger.

7. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise

subjected to damage or stress.

8. An extension cord should not be used unless absolutely necessary. Use of improper

extension cord could result in a risk of fire and electric shock.

If extension cord must be used make sure:

a. That blades of extension cord are the same number, size, and shape as those of plug

on battery charger:

b. That extension cord is properly wired and in good electrical condition; and

c. That wire size is large enough for AC ampere rating of battery charger as specified

in Table 1.

* If the input rating of a battery charger is given in watts rather than in amperes, the

corresponding ampere rating is to be determined by dividing the wattage rating by the

voltage rating–for example:

9. Do not operate battery charger with damaged cord or plug-replace them immediately.

Table 1

RECOMMENDED MINIMUM AWG SIZE FOR

EXTENSION CORDS FOR BATTERY CHARGERS

AC Input Rating Amperes* AWG Size of Cord

Equal to or but less Length of Cord, Feet (Meter)

greater than than 25 (7.5) 50 (15) 100 (30) 150 (45)

0 2 18 18 18 16

2 3 18 18 16 14

3 4 18 18 16 14

1250watts

125 volts

= 10 amperes

DV14DV•DV18DV-E.E65 6/21/02, 5:06 PM8

English

10. Do not operate battery charger if it has received a sharp blow, been dropped, or

otherwise damaged in any way; take it to a qualified serviceman.

11. Do not disassemble battery charger; take it to a qualified serviceman when service or

repair is required. Incorrect reassembly may result in a risk of electric shock or fire.

12. To reduce risk of electric shock, unplug charger from receptacle before attempting any

maintenance or cleaning. Removing the battery will not reduce this risk.

IMPORTANT SAFETY INSTRUCTIONS FOR USE OF THE BATTERY

AND BATTERY CHARGER

You must charge the battery before you can use the cordless hammer drill. Before using the

model UC24YFA/UC24YF battery charger, be sure to read all instructions and cautionary

statements on it, the battery and in this manual.

REMEMBER: USE ONLY HITACHI BATTERY TYPES EB7 SERIES, EB9 SERIES, EB12 SERIES,

EB14 SERIES, EB18 SERIES AND EB24B. OTHER TYPES OF BATTERIES MAY BURST AND

CAUSE INJURY!

Follow these instructions to avoid the risk of injury:

WARNING: Improper use of the battery or battery charger can lead to serious injury.

To avoid these injuries:

1. NEVER disassemble the battery.

2. NEVER incinerate the battery, even if it is damaged or is completely worn out. The

battery can explode in a fire.

3. NEVER short-circuit the battery.

4. NEVER insert any objects into the battery charger’s air vents. Electric shock or

damage to the battery charger may result.

5. NEVER charge outdoors. Keep the battery away from direct sunlight and use only

where there is low humidity and good ventilation.

6. NEVER charge when the temperature is below 32°F (0°C) or above 104°F (40°C).

7. NEVER connect two battery chargers together.

8. NEVER insert foreign objects into the hole for the battery or the battery charger.

9. NEVER use a booster transformer when charging.

10. NEVER use an engine generator or DC power to charge.

11. NEVER store the battery or battery charger in places where the temperature may

reach or exceed 104°F (40°C).

12. ALWAYS operate charger on standard household electrical power (120 volts). Using

the charger on any other voltage may overheat and damage the charger.

13. ALWAYS wait at least 15 minutes between charges to avoid overheating the charger.

14. ALWAYS disconnect the power cord from its receptacle when the charger is not in use.

DV14DV•DV18DV-E.E65 6/21/02, 5:06 PM9

English

DISPOSAL OF THE EXHAUSTED BATTERY

WARNING: Do not dispose of the exhausted battery. The battery must explode if it

is incinerated. The product that you have purchased contains a re-

chargeable battery. The battery is recyclable. At the end of it’s useful

life, under various state and local laws, it may be illegal to dispose of this

battery into the municipal waste stream. Check with your local solid

waste officials for details in your area for recycling options or proper

disposal.

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO

OTHER USERS

AND

OWNERS OF THIS TOOL!

DV14DV•DV18DV-E.E65 6/21/02, 5:06 PM10

English

Nameplate

Terminal Hole

Latch

FUNCTIONAL DESCRIPTION

NOTE:

The information contained in this Instruction Manual is designed to assist you in the safe

operation and maintenance of the power tool.

NEVER operate, or attempt any maintenance on the tool unless you have first read and

understood all safety instructions contained in this manual.

Some illustrations in this Instruction Manual may show details or attachments that differ

from those on your own power tool

MODEL

DV14DV (BFK): with charger (UC24YFA) and case

DV18DV (BFK): with charger (UC24YFA or UC24YF) and case

NAME OF PARTS

1. Cordless Hammer Drill (DV14DV and DV18DV)

䡬 Battery (EB14B) 䡬 Battery (EB1820 or EB18B)

Fig. 1

Switch Trigger

Indication

Cap

Keyless Chuck

Shift Knob

Handle

Battery

Push

Button

Nameplate

Indication

Nameplate

Terminal Hole

Latch

DV14DV•DV18DV-E.E65 6/21/02, 5:06 PM11

English

2. Battery Charger (UC24YFA or UC24YF)

Fig. 2

SPECIFICATIONS

1. Cordless Hammer Drill

2. Battery Charger

NOTE: The charging time may vary according to temperature and power source voltage.

Model DV14DV DV18DV

Motor DC motor

No-load speed

Low 0–350/min 0–400/min

High 0–1200/min 0–1500/min

Capacity Drilling Brick (Depth 9/16"(14mm) 5/8"(16mm)

1-1/4" (30mm)) (Soft Brick) (Soft Brick)

Wood (Thickness 1-1/4"(32mm) 1-1/2"(38mm)

11/16" (18mm)) (Soft Wood) (Soft Wood)

Metal (Thickness 1/2" (13mm) 1/2" (13mm)

1/16"(1.6mm))

(Mild Steel or Aluminum) (Mild Steel or Aluminum)

Screw

Wood screw

#20 × 2" #20 × 3"

driving (8mm × 50mm) (8mm × 75mm)

Small screw 1/4"(6mm) 1/4"(6mm)

Drill chuck capacity Maximum gripping diameter 1/2" (13mm)

Battery Model EB14B EB1820/EB18B

Type Nickel cadmium battery

Voltage DC 14.4V DC 18V

Charging & discharging

about 1000 times

frequency

Weight 4.9 lbs. (2.2 kg) 5.3 lbs. (2.4 kg)

Model UC24YFA UC24YF

Input power source Single phase: AC120V 60Hz

Charging time

Approx. 50min. Approx. 60min.

(At a temperature of 68°F (20°C))

Charging voltage DC 7.2–24V

Charging current DC 2.5A DC2.1A

Weight 1.3 lbs (0.6kg) 2.2 lbs (1kg)

Caution Plate

Battery Installation Hole

Pilot Lamp

Nameplate

DV14DV•DV18DV-E.E65 6/21/02, 5:06 PM12

English

ASSEMBLY AND OPERATION

APPLICATIONS

䡬 Use as a hammer drill

Drilling of soft bricks and concrete blocks.

䡬 Use as a drill

Drilling of soft steel, wood, plastic and aluminum materials.

䡬 Use as a screwdriver

Tightening and loosening of machine screws, wood screws and tapping screws.

REMOVAL AND INSTALLATION METHOD OF BATTERY

䡬 How to install the battery.

Align the battery with the groove in tool

handle and slip it into place.

Always insert it all the way until it locks in

place with a little click, If not, it may acciden-

tally fall out of the tool, causing injury to

you or someone around you. (Fig. 3)

䡬 How to remove the battery.

Withdraw battery from the tool handle while

pressing the latches on the sides of the

battery. (Fig. 3)

CHARGING METHOD

NOTE: Before plugging into the receptacle, make sure the following points.

䡬 The power source voltage is stated on the nameplate.

䡬 The cord is not damaged.

WARNING: Do not charge at voltage higher than indicated on the nameplate.

If charged at voltage higher than indicated on the nameplate, the

charger will burn up.

1. Insert the plug of battery charger into

the receptacle.

When the plug of battery charger has been

inserted into the receptacle, pilot lamp will

blink in red. (At 1-second intervals)

Fig. 3

Battery

Fig. 4

Latch

Push

Switch Trigger

Handle

Battery

Pull out

Insert

Pilot Lamp

DV14DV•DV18DV-E.E65 6/21/02, 5:06 PM13

English

2. Insert the battery to the battery charger.

Insert the battery into the battery charger as shown in Fig. 4. Make sure it contacts the

bottom of the battery charger.

3. Charging

When the battery is connected to the battery charger, charging will commence and the

pilot lamp will light in red. (See Table 2)

NOTE: If the pilot lamp flickers in red, pull out the plug from the receptacle and check if

the battery is properly mounted.

When the battery is fully charged, the pilot lamp will blink in red slowly. (At 1-second

intervals) (See Table 2)

(1) Pilot lamp indication

The indications of the pilot lamp will be as shown in Table 2, according to the condition

of the charger or the rechargeable battery.

(2) Regarding the temperature of the rechargeable battery.

The temperatures for rechargeable batteries are as shown in the table below, and

batteries that have become hot should be cooled for a while before being recharged.

Table 2

Indications of the pilot lamp

Lights for 0.5 seconds. Does not light for

0.5 seconds. (off for 0.5 seconds)

Lights continuously

Lights for 0.5 seconds. Does not light for

0.5 seconds. (off for 0.5 seconds)

Lights for 0.1 seconds. Does not light for

0.1 seconds. (off for 0.1 seconds)

Lights continuously

Before

charging

While

charging

Charging

complete

Charging

impossible

Charging

impossible

Malfunction in the battery or the

charger

The battery temperature is high,

making recharging impossible.

Blinks

(RED)

Lights

(RED)

Blinks

(RED)

Flickers

(RED)

Lights

(GREEN)

WARNING:

Do not use the electrical cord if damaged. Have it repaired

immediately.

Table 3 Recharging of batteries that have become hot

Temperatures at which the battery can be recharged

23°F—140°F

(–5°C—60°C)

Rechargeable batteries

EB14B, EB1820, EB18B

DV14DV•DV18DV-E.E65 6/21/02, 5:06 PM14

English

4. Disconnect battery charger from the receptacle.

CAUTION:

Do not pull the plug out of the receptacle by pulling on the cord.

Make sure to grasp the plug when removing from receptacle to avoid damaging cord.

5. Remove the battery from the battery charger.

Supporting the battery charger with hand, pull out the battery from the battery charger.

CAUTION:

● When the battery charger has been continuosly used, the battery charger will be heated,

thus constituting the cause of the failures. Once the charging has been completed, give

15 minutes rest until the next charging.

● If the battery is rechraged when it is warm due to battery use or exposure to sunlight,

the pilot lamp may light in green.

The battery will not be recharged. In such a case, let the battery cool before charging.

● When the pilot lamp flickers in red (at 0.2–second intervals), check for and take out any

foreign objects in the charger’s battery installation hole. If there are no foreign objects,

it is probable that the battery or charger is malfunctioning. Take it to your authorized

Service Center.

Regarding electric discharge in case of new batteries, etc.

As the internal chemical substance of new batteries and batteries that have not been

used for an extended period is not activated, the electric discharge might be low when

using them the first and second time. This is a temporary phenomenon, and normal time

required for recharging will be restored by recharging the batteries 2 – 3 times.

How to make the batteries perform longer.

(1) Recharge the batteries before they become completely exhausted.

When you feel that the power of the tool becomes weaker, stop using the tool and

recharge its battery. If you continue to use the tool and exhaust the electric current, the

battery may be damaged and its life will become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after use. If such a battery is recharged

immediately after use, its internal chemical substance will deteriorate, and the battery

life will be shortened. Leave the battery and recharge it after it has cooled for a while.

BEFORE USE

Check the work area to make sure that it is clear of debris and clutter.

Clear the area of unnecessary personnel. Ensure that lighting and ventilation is adequate.

DV14DV•DV18DV-E.E65 6/21/02, 5:06 PM15

English

OPERATION

1. Mounting and dismounting the bit

(1) Mounting the bit.

Insert a screwdriver bit etc. into the keyless drill chuck.

Firmly grasp the ring and tighten the sleeve by turning it

toward the right (in the clockwise direction as viewed

from the front). (See Fig.5)

NOTE: If the sleeve becomes loose during operation, tighten

it further.

The tightening force becomes stronger when the

sleeve is tightened.

(2) Dismounting the bit.

Firmly grasp the ring and loosen the sleeve by turning it toward the left (in the

counterclockwise direction as viewed from the front). (See Fig.5)

CAUTION:

When mounting a bit into the keyless chuck, tighten firmly. If the sleeve is not tight, the

bit may slip or fall out, causing injury.

NOTE: Loosening stuck or hard to move sleeves.

Grasp the bit installed in the keyless chuck, in a vise or similar tool.

Set the cap position to “1-11” and turn on the switch. The motor then starts.

Finally, rotate the sleeve to the left, and it will loosen.

2. Confirm that the battery is mounted correctly.

3. Check the rotational direction

The bit rotates clockwise (viewed from the rear side) by

pushing the R-side of the selector button.

The L-side of the selector button is pushed to turn the bit

counterclockwise. (See Fig. 6). (The

and

marks are

provided on the body.)

䡬 When the trigger switch is depressed, the tool rotates.

When the trigger is released, the tool stops.

䡬 The rotational speed of the drill can be controlled by

varying the amount that the trigger switch is pulled.

Speed is low when the trigger switch is pulled slightly and

increases as the trigger switch is pulled more.

䡬 When releasing the trigger of the switch, the brake will be

applied for immediate stopping.

Fig. 5

Tighten

Loosen

Sleeve

Ring

Fig. 6

Triger

switch

Selector

Button

marks

DV14DV•DV18DV-E.E65 6/21/02, 5:06 PM16

English

4. Change rotation speed

Operate the shift knob to change the rotational speed. Move the shift knob in the direction

of the arrow (see Figs. 7 and 8).

When the shift knob is set to “LOW”, the drill rotates at a low speed. When set to “HIGH”,

the drill rotates at a high speed.

CAUTION:

● When changing the rotational speed with the shift knob, confirm that the switch is off.

Changing the speed while the motor is rotating will damage the gears.

● When a large force is required for operation (operations indicated in the following chart)

set the shift knob to “LOW”. If “HIGH” is set and the unit is used, it may cause the motor

to burn out or malfunction prematurely.

5. Confirm the cap position (see Fig. 9)

The three modes of screwdriver, drill and hammer drill

can be switched by the position of the cap in this unit.

(1) When using this unit as a screwdriver, line up the one of

the numbers “1, 3, 5 ... 22” on the cap, or white dots, with

the triangle mark on the outer body.

(2) When using this unit as a drill, align the cap drill mark “

”

with the triangle mark on the outer body.

(3) When using this unit as a hammer drill, align the cap

hammer mark “

” with the triangle mark on the outer

body.

Fig. 7

Fig. 8

Model DS14DVB DS18DVB

Brick Drilling

Metal Drilling

Wood Drilling

Wood Screw

Tightening

When the diameter of the hole

exceeds 1/4"(6.5mm).

When the diameter of the hole

exceeds 11/16"(18mm).

When the diameter of the hole

exceeds 5/16"(8mm).

When the diameter of the hole

exceeds 15/16"(24mm).

When the size of the wood screw exceeds 3/16"(4.8mm)

diameter × 1-9/16"(40mm).

Fig. 9

Shift knob

Low speed

High speed

Cap

Triangle mark

When the diameter of the hole exceeds 3/8"(10mm).

DV14DV•DV18DV-E.E65 6/21/02, 5:06 PM17

English

CAUTION:

䢇 The cap cannot be set between the numerals “1, 3, 5 ...

22” or the white dot.

䢇 Do not use with the cap numeral at “22” and the white

line at the middle of the drill mark. Doing so may cause

damage. (See Fig. 10)

6. Rotation to Hammer changeover

The "Rotation (Rotation only)" and "Hammer (Hammer + Rotation)" can be switched by

aligning the drill mark "

" or the hammer mark " " with the triangle mark on the outer

body.

䡬 To make holes in the metal, wood or plastic, switch to "Rotation (Rotation only)".

䡬 To make holes in the bricks or concrete blocks, switch to "Hammer (Hammer + Rotation)".

CAUTION:

Do not use the hammer drill in the "Hammer" setting if the material can be bored by

rotation only. Such action will not only reduce drill efficiency, but may also damage the

drill tip.

7. Tightening torque adjustment

(1) Tightening torque

Tightening torque should correspond in its intensity to the screw diameter. When too

strong power is used, the screw head may be broken or be injured.

Be sure to adjust the cap position according to the screw diameter.

(2) Tightening torque indication (See Fig. 9)

The tightening torque differs depending on the type of screw and the material being

tightened.

The unit indicates the tightening torque with the numbers “1, 3, 5 ... 22” on the cap, and

a white dot. The tightening torque at position “1” is the weakest and the torque is

strongest at the highest number.

(3) Adjusting the tightening torque (See Fig. 9)

Rotate the cap and line up the numbers “1, 3, 5, ... 22” on the cap, or the white dot, with

the triangle mark on the outer body. Adjust the cap in the weak or the strong torque

direction according to the torque you need.

CAUTION:

䢇 The motor rotation may be locked to cease while the unit is used as drill. While operating

the hammer drill, take care not to lock the motor.

䢇 When setting the shift knob to “HIGH” (high speed) and the position of the cap is “17”

or “22”, it may happen that the clutch does not engaged and that the motor is locked.

In such a case, please set the shift knob to “LOW” (low speed).

䢇 If the motor is locked, immediately turn the power off. If the motor is locked for a while,

the motor or battery may be burnt.

䢇 Too long hammering may cause the screw broken due to excessive tightening.

䢇 A buzzing noise is produced when the motor is about to rotate; This is only a noise, not

a machine failure.

Fig. 10

White

line

Drill markHammer mark

DV14DV•DV18DV-E.E65 6/21/02, 5:06 PM18

English

8. For drilling into brick

CAUTION:

䢇 When the hammer drill is used continuously, the body may be heated. If this happens,

leave the hammer drill to cool.

䢇 Excessive pressing force never increases drilling speed. It will not only damage the drill

tip or reduce working efficiency, but could also shorten the service life of drill bit.

Operate hammer drill within 20 – 30 lbs. (10 – 15 kg) pressing force while drilling into

brick.

THE SCOPE AND SUGGESTIONS FOR USES

Table 4

Work Cap position Suggestions

Brick Use for drilling purpose.

Wood

Drilling

Steel

Use for drilling purpose.

Aluminum

Screw

Small

1 – 22

Use the bit and socket matching the screw

tightening

screw diameter.

Wood

1 –

Use after drilling a pilot hole.

screw

DV14DV•DV18DV-E.E65 6/21/02, 5:06 PM19

English

HOW TO SELECT TIGHTENING TORQUE

Table 5

NOTE:

The selected content shown in Table 5 indicates the differences according to screw type,

screw size and material used.

CAUTION:

● While operating the Cordless hammer drill, take care not to lock the motor.

If the motor is locked, immediately turn the power off.

If the motor is locked for a while, the motor or battery will be burnt.

● Do not tighten too strongly as the screw heads will be damaged.

Cap

Tightening torque Operation example

position

Approximately 9 in-lbs. (10 kg-cm)

Approximately 15 in-lbs. (17 kg-cm)

Approximately 23 in-lbs. (26 kg-cm)

Approximately 35 in-lbs. (40 kg-cm)

Approximately 43 in-lbs. (49 kg-cm)

Approximately 52 in-lbs. (60kg-cm)

High speed: approximately 78 in-lbs.

(90 kg-cm)(DV14DV)

approximately 96 in-lbs.

(110 kg-cm)(DV18DV)

Low speed: approximately 346 in-lbs.

(400 kg-cm)(DV14DV)

approximately 400 in-lbs.

(460 kg-cm)(DV18DV)

Machine screw

tightening.

Screw tightening for soft

wood material.

Screw tightening for

hard wood material.

Thick screw tightening.

When used as a drill.

Use for drilling bricks

and concrete blocks.

DV14DV•DV18DV-E.E65 6/21/02, 5:06 PM20

La page charge ...

Hitachi DV 14DV Safety And Instruction Manual

Marque: Hitachi

Modèle: DV 14DV

Catégorie: Perceuses mixtes sans fil

Taper: Safety And Instruction Manual

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Hitachi DV 14DV
español: Hitachi DV 14DV

Hitachi DV 14DV Safety And Instruction Manual

Ce manuel convient également à

Hitachi DV 14DV Safety And Instruction Manual

dans d''autres langues

Documents connexes

Autres documents