Malone MPG113MD Manuel utilisateur

Marque: Malone

Modèle: MPG113MD

Taper: Manuel utilisateur

MALONE

MPG113

MALONE

DownLoaderDownLoaderTM

J-STYLE FOLDING KAYAK CARRIER

12’ Safety LinesJawz Universal Adapters Mounting BoltsKayak Carriers Load Straps T-Knobs

60mm

70mm

Installation & Loading Instructions - Please Read Before Beginning

Veuillez lire les instructions avant d’entreprendre l’installation et le chargement

. Insert Mounting Bolt through one hole of a Jawz adapter.

Insert washer and loosely apply a T-knob. See image 2.

. Faites passer le boulon de fixation dans l’un des trous

d’un adaptateur Jawz puis vissez légèrement un bouton

en ‘‘T’’ à la base du boulon. (Figure 2)

. Prior to installation, insert a bolt into the mounting holes in

the bottom of the carriers. Push upward to open the two

mounting hole covers located in the Base pads.

. Insert a Mounting Bolt into one mounting hole from the top

side. Rotate and close the mounting hole cover.

See image 1.

. Insérez un boulon de fixation dans l’un des trous hexagonaux

situés sur le côté supérieur du support.

(Figure 1)

. Place the carrier onto the front cross bar with the boarding

ramp facing out. Swing the Jawz under the cross bar as

shown. See image 3.

. Placez le support sur la barre transversale avant, la rampe

de chargement vers l’extérieur. Faites passer l’adaptateur

Jawz sous la barre transversale, tel qu’indiqué. (Figure 3)

Mounting Bolt Washers

Base Pad

Covers

IMPORTANT WARNING: All vehicular transports are potentially hazardous. Any person(s) using Malone products are personally responsible for

following the given directions for use and/or installation and accepts full responsibility for any and all damages or injury of any kind including death,

which may result from their use and/or installation.

It is critical that all Malone racks and accessories be properly and securely attached to your vehicle. Improper attachment could result in a serious

accident, and could cause serious bodily injury or death to you or to others. You are responsible for securing the racks and accessories to your car,

checking the attachment’s prior to use, and periodically inspecting the products for adjustment, wear, and damage.

You must read and understand all of the instructions and cautions supplied with your Malone products(s) prior to installation or use. If you do not

understand all of the instructions and cautions, or, if you have no mechanical experience and are not thoroughly familiar with the installation

procedures, you should have the product installed by a professional installer.

MISE EN GARDE IMPORTANTE: Tout transport d’un chargement sur le toit d’un véhicule est potentiellement dangereux. Une personne qui

utilise les produits Malone doit suivre sans faute les instructions d’installation et d’utilisation fournies et assume l’entière responsabilité pour tout

dommage ou toute blessure, y compris un décès, pouvant résulter d’une telle installation ou utilisation.

Il est essentiel de xer correctement et solidement les supports et les accessoires à votre véhicule. Une mauvaise installation ou attache pourrait

provoquer un accident, entraîner des blessures corporelles graves à vous et aux autres et même causer la mort. Vous avez la responsabilité de

xer solidement les supports et les accessoires à votre véhicule, de vérier l’installation avant l’utilisation et d’inspecter périodiquement le produit

pour déceler tout signe d’usure ou de dommage ou tout problème d’ajustement.

Vous devez lire et comprendre les instructions et les mises en garde fournies avec les produits Malone avant l’installation et l’utilisation. Si vous

ne comprenez pas les instructions et les mises en garde ou si vous ne possédez pas d’expérience en mécanique et ne connaissez pas à fond les

procédures à suivre d’installation, vous devriez faire monter et poser le produit par un installateur professionnel.

MALONE

SS ComboSS Combo

SEAWING KAYAK CARRIER with

STINGER LOAD ASSIST

Extension Frame Mounting Plate V-Block 70mm Bolts

Stinger Load Assist Components

Installation & Loading Instructions - Please Read Before Beginning

. Insert the two 1” bolts into the two holes

located on the bottom side of the Extension

Frame. Tighten with a phillips screwdriver.

See image 2.

Step 1: Stinger Pre-Assembly

. Place the V-Block into the channel located directly

behind the Malone logo on the Extension Frame.

See image 1.

12’ Safety Lines

MD Series Only

Jawz Universal Adapters Mounting Bolts

60mm

50mm

SeaWing Kayak Carriers 12’ Load Straps T-Knobs

Rubber Plugs

SeaWing Kayak Carrier Components

T-knobs

1” Bolts1 3/4” Bolts

Important Note

Product Warranty & Registration Form

All information is condential and used exclusively by MALONE only.

MALONE

MALONE AUTO RACKS 81 County Rd. Ste 1, Westbrook, ME 04092

P: 207.774.9100 F: 207.615.0551

E: support@maloneautoracks.com W: www.maloneautoracks.com

Dear Customer,

Thank you for your purchase of a Malone Product.

In order to be eligible for the Malone Warranty program, we ask that you contact us online at the link provided

below: With-in 30 days of purchase. You can also mail this letter back to the address at the bottom.

• Online: https://maloneautoracks.com/product-registration.php

We will require the information below.

Here is the information collected:

First Name:

Last Name:

Address:

Address2:

City:

State:

Zip:

Country:

Email:

Phone:

Product Description/Name:

Product MPG#

Date Purchased:

Store Where Purchased:

Purchase Price:

Thank you for choosing Malone!

MALONE

SS ComboSS Combo

SEAWING KAYAK CARRIER with

STINGER LOAD ASSIST

Extension Frame Mounting Plate V-Block 70mm Bolts

Stinger Load Assist Components

Installation & Loading Instructions - Please Read Before Beginning

. Insert the two 1” bolts into the two holes

located on the bottom side of the Extension

Frame. Tighten with a phillips screwdriver.

See image 2.

Step 1: Stinger Pre-Assembly

. Place the V-Block into the channel located directly

behind the Malone logo on the Extension Frame.

See image 1.

12’ Safety Lines

MD Series Only

Jawz Universal Adapters Mounting Bolts

60mm

50mm

SeaWing Kayak Carriers 12’ Load Straps T-Knobs

Rubber Plugs

SeaWing Kayak Carrier Components

T-knobs

1” Bolts1 3/4” Bolts

MALONE

DownLoaderDownLoaderTM

J-STYLE FOLDING KAYAK CARRIER

12’ Safety LinesJawz Universal Adapters Mounting BoltsKayak Carriers Load Straps T-Knobs

60mm

70mm

Installation & Loading Instructions - Please Read Before Beginning

Veuillez lire les instructions avant d’entreprendre l’installation et le chargement

. Insert Mounting Bolt through one hole of a Jawz adapter.

Insert washer and loosely apply a T-knob. See image 2.

. Faites passer le boulon de fixation dans l’un des trous

d’un adaptateur Jawz puis vissez légèrement un bouton

en ‘‘T’’ à la base du boulon. (Figure 2)

. Prior to installation, insert a bolt into the mounting holes in

the bottom of the carriers. Push upward to open the two

mounting hole covers located in the Base pads.

. Insert a Mounting Bolt into one mounting hole from the top

side. Rotate and close the mounting hole cover.

See image 1.

. Insérez un boulon de fixation dans l’un des trous hexagonaux

situés sur le côté supérieur du support.

(Figure 1)

. Place the carrier onto the front cross bar with the boarding

ramp facing out. Swing the Jawz under the cross bar as

shown. See image 3.

. Placez le support sur la barre transversale avant, la rampe

de chargement vers l’extérieur. Faites passer l’adaptateur

Jawz sous la barre transversale, tel qu’indiqué. (Figure 3)

Mounting Bolt Washers

Base Pad

Covers

60mm

Safety Tie-Downs 50mm

T-Knobs

Jawz Brackets

SeaWing Carriers Load Straps Rubber Plugs

MALONE

Installation & Loading Instructions - MPG113MD SS Combo

Align

channels

to holes

. Insert the 1 3/4” Carriage Bolts down and

through the Extension Frame channels and

into the holes in the Mounting Plate.

See image 4.

. Place the Extension Frame on top of the Mounting

Plate with the raised block side facing up. The two

holes located on the end of the Plate should align

with the two channels in the Frame.

See image 3.

. Loosely thread the two T-knobs onto the Bolts.

Slide the Frame forward towards the Mounting

Plate until travel is stopped. Tighten both of

the T-knobs. See image 5.

Step 2: Installing Carriers to Cross Bars

. Place the SeaWing onto the Stinger so that

the mounting holes in both units are aligned.

See image 6.

MALONE

Installation & Loading Instructions - MPG113MD SS Combo

. Insert Bolt through one hole of the Jawz

mounting adapter and loosely apply the

T-knob. See image 8.

Note: Additional bolt lengths available.

. Insert a single 70mm Mounting Bolt down through

the SeaWing and Mounting Plate. See image 7.

. Place the Stinger with SeaWing assembly onto

the rear cross bar of the vehicle with the V-Block

closest to the rear of the vehicle. Swing the Jawz

under the cross bar and insert the second 70mm

Bolt. See image 9.

. Loosely secure the second Bolt with a T-knob.

Position the assembly to the final location.

Finish by firmly tightening the T-knobs. See

image 10.

Insert Mounting Bolt through one hole of a

Jawz adapter and loosely apply a T-knob.

See image 8.

Loosely apply the T-knob. Position the assem-

bly to the nal location and rmly tighten until

the carrier is secure. See image 10.

Note: The base of the carrier has a rectangular “cutout”

that has been included for square cross bar t. This

“cutout” does not effect the t or function of the carriers

when installed to round or oval shaped cross bars.

. Insert a second Mounting Bolt into the top side

unused carrier hex hole and down through the

Jawz mounting adapter. Apply a second T-knob

and slightly tighten until the carrier is secure.

See image 14.

MALONE

Installation & Loading Instructions - MPG113MD SS Combo

. Insert Mounting Bolt through one hole of a

Jawz Mounting Adapter and loosely apply

a T-knob. See image 12.

. Using the second SeaWing carrier, insert a Mounting

Bolt into one of the top side hex holes.

See image 11.

. Place the carrier onto the front cross bar. Swing

the Jawz under the cross bar as shown.

See image 13.

Insert Mounting Bolt through one hole of a Jawz

adapter and loosely apply a T-knob. See image

12.

Insert a second mounting bolt through the unused

hex hole and Jawz adapter. Loosely apply the

second T-knob. Tighten until the carrier is secure.

See image 14.

. Place the straps parallel to the carriers

with the front strap loop on the windshield

and the rear strap loop on the back of the

vehicle. See image 18.

Step 3: Loading the Kayak

. Route the free end of a 12’ Load Strap down through

the top of the outer most strap slot and back up

through the inside slot of the carrier. Pull the free

end until there is an even loop. Repeat for the second

carrier. See image 17.

. Insert the four Rubber Plugs into the four

top side hex holes in the two carriers.

See image 16.

MALONE

Installation & Loading Instructions - MPG113MD SS Combo

. Confirm the carriers are in alignment. Firmly

tighten the T-knobs until both carriers are securely

fixed to the cross bars. See image 15.

. After the kayak has been loaded onto the

carriers, loosen the two Extension Frame

T-knobs and push the Extension Frame back

until the V-Block makes contact with the

kayak. Tighten the T-knobs for transport.

See image 22.

. Lift the rear of the kayak and slowly push forward

until the kayak is centered between the carriers.

See image 21.

. Lift and place the front of the kayak into

the V-Block on the Extension Frame. Walk

to the rear of the kayak while continuing

to hold the kayak in place. See image 20.

MALONE

Installation & Loading Instructions - MPG113MD SS Combo

19 . Loosen the two T-knobs holding the Extension

Frame. Pull the Frame out to the rear edge of

the vehicle and slightly re-tighten the T-knobs.

See image 19.

Note: The Extension Frame will bend down under

the weight of the kayak. The Frame should be

placed so that the rubber pad makes contact with

the vehicle’s rear edge. This will provide support

and protection while the kayak is loaded.

. Position kayak so that the cockpit is evenly centered

between the front and rear carriers. The bottom of

the kayak should be slightly elevated above each of

the carriers and held by the sides of the carriers.

See image 23.

. Place the strap loops over the kayak so that

each loop is positioned directly over a carrier.

See image 24.

MALONE

Installation & Loading Instructions - MPG113MD SS Combo

. Pull the free end of each strap loop down until the

buckles are positioned half way up the side of the

kayak. Thread each free end down and through the

top of the outside slot and back up through the

bottom of the inside slot. See image 25.

. Thread the free strap ends up and through

the buckles. Pull down to tighten. Dress

any extra strap down and around the cross

bars. See image 26.

. For MD series only: Install the bow & stern

safety lines per the attached instructions.

MALONE

Installation & Loading Instructions - MPG113MD SS Combo

MALONE AUTO RACKS, 81 County Road, Westbrook, Maine 04092

Phone: 207-774-9100 Fax: 207-615-0551

Website: www.maloneautoracks.com Email: technical@maloneautoracks.com

Safety tie-downs are required for all transport. If your kit did not include

safety tie-downs, we strongly recommend the use of the Malone

MPG316 Sentry Ratchet Tie-Down System.

For added stability for larger kayaks, dress the straps down under the cross

bars before bringing them back up through the slots in steps 17 and 25.

Always check mounting hardware, load straps and safety tie-down lines for proper

and secure attachment before transport. Use of this product for any other

application other than kayak transport voids warranty.

Warning: All vehicular rooftop transports are potentially hazardous.

Any person using MALONE automotive transport systems is personally

responsible for following the given directions for use and installation

and accepts full and complete responsibility for any and all damages

or injury of any kind including death, which may result from their use.

IMPORTANT NOTES:

Bow and stern safety tie-downs are required for all Malone rooftop transport(s). Failure to correctly install

and use safety tie-down lines voids all warranty and liability.

If your kit did not include safety tie-downs, we strongly recommend the use of the

Malone MPG316 Sentry Ratchet Tie-Down System or Malone MPG309 SpeedLine Mini Ratchet Tie-Down

Visit www.maloneautoracks.com/Replacement-Parts

for all of your spare part needs

MPG370 BOW & STERN LINE KIT

MALONE

Thread free end

of cord through

hook.

Create a “left

over right”

knot & tighten.

Create a “right

over left”

knot & tighten.

Pull to test for

knot strength.

A B C D

Attach hook to rope (steps A-D)

Keeping the rope tight and

S-hook in place, thread the

free end up and through a

strong point on the kayak

Make a loop in the rope

12” to 14” away

from the kayak or canoe.

Attach and dress rope to vehicle and boat (steps E-O)

Attach S-hook to vehicle

tow ring or other sturdy

body part.

Bend the loop over leaving

a large opening as shown.

Opening

Pass the loop through the

opening.

Pull to create a tight knot.

Thread the free end of

the rope

through the loop.

Pull the free end up until

the rope

is sufficiently tight.

Hold the rope secure with

one hand.

Form a knot with the free

end and tighten. Form

a second knot for

safety purposes.

The line should be tight

and secure. Repeat for

second tie-down.

MALONE AUTO RACKS, 81 County Road, Westbrook, Maine 04092

Phone: 207-774-9100 Fax: 207-615-0551

Website: www.maloneautoracks.com Email: technical@maloneautoracks.com

MPG306 BOW & STERN LINE KIT

NOTE: NOT REQUIRED ON TRAILER PACKAGES

MALONE AUTO RACKS 81 County Rd. Ste 1, Westbrook, ME 04092

P: 207.774.9100 F: 207.615.0551

E: support@maloneautoracks.com W: www.maloneautoracks.com

MALONE AUTO RACKS 81 County Rd. Ste 1, Westbrook, ME 04092

P: 207.774.9100 F: 207.615.0551

E: support@maloneautoracks.com W: www.maloneautoracks.com

Limited Lifetime Warranty

The Malone Auto Racks (Malone) Limited Lifetime Warranty covers certain Malone-brand products that have been specically

identied for inclusion in the program and is effective for as long as the original retail purchaser owns the product. This warranty is

terminated when the original retail purchaser sells or otherwise transfers the product to any other person or entity.

Subject to the limitations and exclusions described in this warranty, Malone will remedy defects in materials and/or workmanship

by repairing or replacing, at its option, a defective product without charge for parts or labor. Malone may elect, at its option, not to

repair or replace a defective product but rather issue to the original retail purchaser a refund equal to the purchase price paid for the

product, or credit to be used toward the purchase of a replacement Malone product.

This warranty does not cover, and no warranty is given for defects or problems caused by normal wear and tear, which includes,

but is not limited to, surface (aesthetic) metal corrosion, scratches, dents, deformities, accidents, unlawful vehicle operation, or any

modication of a product not performed or authorized in writing by Malone.

In addition, this warranty does not cover problems resulting from conditions beyond Malone’s control including, but not limited to,

theft, misuse, overloading, or failure to assemble, mount or use the product in accordance with Malone’s written instructions or

guidelines included with the product provided to the original retail purchaser.

No warranty is given for Malone products purchased outside of the continental United States, Canada and Mexico.

If the product is believed to be defective, the original retail purchaser should contact the Malone dealer from whom it was purchased,

who will give the original retail purchaser instructions on how to proceed. If the original retail purchaser is unable to contact the

Malone dealer, or the dealer is not able to remedy the defect, the original retail purchaser should contact Malone by email at

[email protected].

In the event that the product must be returned to Malone, a technician at the email address above will provide the original purchaser

with return shipping instructions. The original purchaser will be responsible for the cost of mailing the product to Malone. In order

to be eligible to receive any remedy under this warranty, a copy of the original purchase receipt, a description of the defect and a

return address must be provided.

Disclaimer of Liability

Repair or replacement of a defective product, or the issue of a refund or credit (as determined by Malone) is the original retail

purchaser’s sole and exclusive remedy under this warranty. Damage to original purchaser’s vehicle, cargo, or property, and/ or to

any other person or property is not covered by this warranty.

This warranty is expressly made in lieu of any and all other warranties, express or implied, including the warranties of merchantability

and tness of a particular purpose

Malone’s sole liability to any purchaser is limited to the remedy set forth above. In no event will Malone be liable for any direct,

indirect, consequential, incidental, special, exemplary, or punitive damages , or, for any other damages of any kind or nature

(including but not limited to, lost prots, lost income or lost sales).

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations may not be

applicable.

In addition, all vehicular transports are potentially hazardous. Any person(s) using Malone products are personally responsible for

following the given directions for use and/or installation and accepts full responsibility for any and all damages or injury of any kind

including death, which may result from their use and/or installation.

MALONE

SS ComboSS Combo

SEAWING KAYAK CARRIER with

STINGER LOAD ASSIST

Extension Frame Mounting Plate V-Block 70mm Bolts

Stinger Load Assist Components

Installation & Loading Instructions - Please Read Before Beginning

. Insert the two 1” bolts into the two holes

located on the bottom side of the Extension

Frame. Tighten with a phillips screwdriver.

See image 2.

Step 1: Stinger Pre-Assembly

. Place the V-Block into the channel located directly

behind the Malone logo on the Extension Frame.

See image 1.

12’ Safety Lines

MD Series Only

Jawz Universal Adapters Mounting Bolts

60mm

50mm

SeaWing Kayak Carriers 12’ Load Straps T-Knobs

Rubber Plugs

SeaWing Kayak Carrier Components

T-knobs

1” Bolts1 3/4” Bolts

Insérer deux boulons de 2,5 cm dans les

trous situés sur la face du dessous du cadre

d’extension. Serrer avec un tournevis

cruciforme. Voir image 2.

Placer le bloc en V dans la cavité située directement

derrière le logo de Malone sur le cadre d’extension.

Voir image 1.

MALONE

DownLoaderDownLoaderTM

J-STYLE FOLDING KAYAK CARRIER

12’ Safety LinesJawz Universal Adapters Mounting BoltsKayak Carriers Load Straps T-Knobs

60mm

70mm

Installation & Loading Instructions - Please Read Before Beginning

Veuillez lire les instructions avant d’entreprendre l’installation et le chargement

. Insert Mounting Bolt through one hole of a Jawz adapter.

Insert washer and loosely apply a T-knob. See image 2.

. Faites passer le boulon de fixation dans l’un des trous

d’un adaptateur Jawz puis vissez légèrement un bouton

en ‘‘T’’ à la base du boulon. (Figure 2)

. Prior to installation, insert a bolt into the mounting holes in

the bottom of the carriers. Push upward to open the two

mounting hole covers located in the Base pads.

. Insert a Mounting Bolt into one mounting hole from the top

side. Rotate and close the mounting hole cover.

See image 1.

. Insérez un boulon de fixation dans l’un des trous hexagonaux

situés sur le côté supérieur du support.

(Figure 1)

. Place the carrier onto the front cross bar with the boarding

ramp facing out. Swing the Jawz under the cross bar as

shown. See image 3.

. Placez le support sur la barre transversale avant, la rampe

de chargement vers l’extérieur. Faites passer l’adaptateur

Jawz sous la barre transversale, tel qu’indiqué. (Figure 3)

Mounting Bolt Washers

Base Pad

Covers

60mm

Safety Tie-Downs 50mm

T-Knobs

Jawz Brackets

SeaWing Carriers Load Straps Rubber Plugs

MALONE

Installation & Loading Instructions - MPG113MD SS Combo

Align

channels

to holes

. Insert the 1 3/4” Carriage Bolts down and

through the Extension Frame channels and

into the holes in the Mounting Plate.

See image 4.

. Place the Extension Frame on top of the Mounting

Plate with the raised block side facing up. The two

holes located on the end of the Plate should align

with the two channels in the Frame.

See image 3.

. Loosely thread the two T-knobs onto the Bolts.

Slide the Frame forward towards the Mounting

Plate until travel is stopped. Tighten both of

the T-knobs. See image 5.

Step 2: Installing Carriers to Cross Bars

. Place the SeaWing onto the Stinger so that

the mounting holes in both units are aligned.

See image 6.

Placer le cadre d’extension sur la plaque de montage,

le côté du bloc surélevé vers le haut. Les deux trous à

l’extrémité de la plaque doivent être alignés avec les

deux rainures du cadre. Voir image 3.

Insérer les boulons de carrosserie (4,4 cm)

dans les rainures du cadre d’extension et

dans les trous de la plaque de montage.

Voir image 4.

Visser sans serrer des boutons en T sur les boulons.

Faire glisser le cadre vers la plaque de montage

jusqu’à arrêt complet. Serrer les deux boutons en T.

Voir image 5.

Placer un support SeaWing sur la plaque

Stinger de manière à aligner les trous des

deux unités. Voir image 6.

MALONE

Installation & Loading Instructions - MPG113MD SS Combo

. Insert Bolt through one hole of the Jawz

mounting adapter and loosely apply the

T-knob. See image 8.

Note: Additional bolt lengths available.

. Insert a single 70mm Mounting Bolt down through

the SeaWing and Mounting Plate. See image 7.

. Place the Stinger with SeaWing assembly onto

the rear cross bar of the vehicle with the V-Block

closest to the rear of the vehicle. Swing the Jawz

under the cross bar and insert the second 70mm

Bolt. See image 9.

. Loosely secure the second Bolt with a T-knob.

Position the assembly to the final location.

Finish by firmly tightening the T-knobs. See

image 10.

Insérer un boulon de xation de 70 mm dans le SeaW-

ing et la plaque de montage. Voir image 7.

Insérer un boulon dans un trou de l’adap-

tateur Jawz et visser sans serrer un bouton

en T. Voir image 8.

Note : autres longueurs de boulon

disponibles.

Placer l’assemblage Stinger/Seawing sur la barre

transversale arrière du véhicule, avec le bloc en V situé

le plus près possible de l’arrière du véhicule. Glisser le

Jawz sous la barre transversale et insérer un boulon de

70 mm. Voir image 9.

Visser le bouton en T sans serrer. Mettre l’as-

semblage dans sa position nale et serrer à

fond jusqu’à ce que le support soit arrimé.

Voir image 10.

. Insert a second Mounting Bolt into the top side

unused carrier hex hole and down through the

Jawz mounting adapter. Apply a second T-knob

and slightly tighten until the carrier is secure.

See image 14.

MALONE

Installation & Loading Instructions - MPG113MD SS Combo

. Insert Mounting Bolt through one hole of a

Jawz Mounting Adapter and loosely apply

a T-knob. See image 12.

. Using the second SeaWing carrier, insert a Mounting

Bolt into one of the top side hex holes.

See image 11.

. Place the carrier onto the front cross bar. Swing

the Jawz under the cross bar as shown.

See image 13.

Insérer un boulon de montage dans l’un des trous hex-

agonaux du deuxième support SeaWing. Voir image 11.

Insérez Boulon de montage à travers un trou

d’un adaptateur Jawz et appliquer de manière

lâche un T-bouton. Voir image 12

Placez le support sur la barre transversale avant. Fait-

es pivoter le Jawz sous la barre transversale, comme

indiqué. Voir image 13

Insérer un boulon dans l’autre trou et dans l’ad-

aptateur Jawz. Visser un bouton en T sans ser-

rer à fond. Serrer jusqu’à ce que le support soit

attaché. Voir image 14.

. Place the straps parallel to the carriers

with the front strap loop on the windshield

and the rear strap loop on the back of the

vehicle. See image 18.

Step 3: Loading the Kayak

. Route the free end of a 12’ Load Strap down through

the top of the outer most strap slot and back up

through the inside slot of the carrier. Pull the free

end until there is an even loop. Repeat for the second

carrier. See image 17.

. Insert the four Rubber Plugs into the four

top side hex holes in the two carriers.

See image 16.

MALONE

Installation & Loading Instructions - MPG113MD SS Combo

. Confirm the carriers are in alignment. Firmly

tighten the T-knobs until both carriers are securely

fixed to the cross bars. See image 15.

Assurez-vous que les supports soient bien alignés.

Vissez fermement les boutons en ‘‘T’’ jusqu’à ce que les

deux supports soient solidement xés aux barres trans-

versales. Voir image 15

Insérez un bouchon de caoutchouc dans

chacun des quatre trous hexagonaux situés

sur le côté supérieur des supports.

Voir image 16

Faites passer le bout plat d’une des courroies de xation

de 3,6 mètres autour de la partie supérieure du support

arrière.Tirez sur le bout plat de la courroie an d’obtenir

une boucle de longueurs égales. Faites de même pour

le deuxième support. Voir image 17

Placez les courrories an qu’elles soinet par-

alléles aux supports. La boucle de la courrorie

avant devrait être placée sur le pare-brise

et la seconde boulce sur la partie arriére du

véhicule. Voir image 18

. After the kayak has been loaded onto the

carriers, loosen the two Extension Frame

T-knobs and push the Extension Frame back

until the V-Block makes contact with the

kayak. Tighten the T-knobs for transport.

See image 22.

. Lift the rear of the kayak and slowly push forward

until the kayak is centered between the carriers.

See image 21.

. Lift and place the front of the kayak into

the V-Block on the Extension Frame. Walk

to the rear of the kayak while continuing

to hold the kayak in place. See image 20.

MALONE

Installation & Loading Instructions - MPG113MD SS Combo

19 . Loosen the two T-knobs holding the Extension

Frame. Pull the Frame out to the rear edge of

the vehicle and slightly re-tighten the T-knobs.

See image 19.

Note: The Extension Frame will bend down under

the weight of the kayak. The Frame should be

placed so that the rubber pad makes contact with

the vehicle’s rear edge. This will provide support

and protection while the kayak is loaded.

Desserrer les deux boutons en T retenant le cadre

d’extension. Tirer le cadre jusqu’au bord arrière du

véhicule et resserrer modérément. Voir image 19.

Note : Le cadre d’extension échira sous le poids du

kayak. Il faut installer le cadre de manière à ce que le

tampon de caoutchouc entre en contact avec le bord

arrière du véhicule, assurant un support et une protec-

tion pendant le transport du kayak.

Soulever l’avant du kayak et le placer dans

le bloc en V du cadre d’extension. En main-

tenant le kayak en place, dirigez-vous vers

l’arrière du kayak. Voir image 20.

Soulever l’arrière du kayak et le pousser doucement

vers l’avant jusqu’à ce qu’il soit centré sur les supports.

Voir image 21.

Après le chargement du kayak, desserrer les

deux boutons en T du cadre d’extension et

pousser le cadre jusqu’à ce que le bloc en V

entre en contact avec le kayak. Serrer à fond les

boutons en T pour le transport. Voir image 22.

. Position kayak so that the cockpit is evenly centered

between the front and rear carriers. The bottom of

the kayak should be slightly elevated above each of

the carriers and held by the sides of the carriers.

See image 23.

. Place the strap loops over the kayak so that

each loop is positioned directly over a carrier.

See image 24.

MALONE

Installation & Loading Instructions - MPG113MD SS Combo

. Pull the free end of each strap loop down until the

buckles are positioned half way up the side of the

kayak. Thread each free end down and through the

top of the outside slot and back up through the

bottom of the inside slot. See image 25.

Position kayak de sorte que le cockpit est uniformément

centré entre les transporteurs avant et arrière. Le fond du

kayak devrait être légèrement élevée au-dessus chacune

des porteuses et maintenu par les côtés des

transporteurs.

Voir image 23

Placez les boucles des courroies sur le kayak

an que chaque boucle soit bien alignée avec un

support. Voir image 24

Tirer sur l’extrémité libre de chaque sangle jusqu’à ce

que les boucles soient au milieu sur le côté du kayak.

Enler l’extrémité libre vers le bas dans la fente ex-

térieure et ensuite vers le haut dans la fente intérieure.

Voir image 25.

. Thread the free strap ends up and through

the buckles. Pull down to tighten. Dress

any extra strap down and around the cross

bars. See image 26.

. For MD series only: Install the bow & stern

safety lines per the attached instructions.

MALONE

Installation & Loading Instructions - MPG113MD SS Combo

MALONE AUTO RACKS, 81 County Road, Westbrook, Maine 04092

Phone: 207-774-9100 Fax: 207-615-0551

Website: www.maloneautoracks.com Email: technical@maloneautoracks.com

Safety tie-downs are required for all transport. If your kit did not include

safety tie-downs, we strongly recommend the use of the Malone

MPG316 Sentry Ratchet Tie-Down System.

For added stability for larger kayaks, dress the straps down under the cross

bars before bringing them back up through the slots in steps 17 and 25.

Always check mounting hardware, load straps and safety tie-down lines for proper

and secure attachment before transport. Use of this product for any other

application other than kayak transport voids warranty.

Warning: All vehicular rooftop transports are potentially hazardous.

Any person using MALONE automotive transport systems is personally

responsible for following the given directions for use and installation

and accepts full and complete responsibility for any and all damages

or injury of any kind including death, which may result from their use.

IMPORTANT NOTES:

Insérer les extrémités libres des sangles dans

les boucles de xation. Tirer pour serrer. Attacher

la partie en trop des sangles autour des barres

transversales. Voir image 26.

Il faut installer des cordes de sécurité pour tous les transports. Le fait de ne pas utiliser de cordes de sécu-

rité annule toutes les garanties. Si votre ensemble ne comprend pas de cordes de sécurité, nous vous

recommandons fortement d’utiliser le système d’attache à cliquet MaloneMPG316 Sentry.

NOTES IMPORTANTES :

Pour plus de stabilité lors du transport de grands kayaks, faire passer les sangles sous les barres transver-

sales avant de les insérer dans les fentes aux étapes 17 et 25.

Avant le transport, toujours vérier le matériel de montage, les sangles et les cordes de sécurité pour

s’assurer que tout est solidement xé. L’utilisation du produit pour tout autre usage que le transport de kayak

annule la garantie.

Mise en garde : Tout transport de chargement sur le toit d’un véhicule est potentiellement dangereux. Une

personne qui utilise un système de transport routier MALONE a la responsabilité de suivre les instructions

fournies d’installation et d’utilisation et accepte l’entière responsabilité pour tout dommage ou toute blessure,

y compris un décès, pouvant résulter d’une telle utilisation.

Il faut toujours utiliser des attaches de sécurité à l’avant et à l’arrière pour les transports sur le toit.

Le défaut d’installer et d’utiliser correctement des cordages de sécurité annule toutes les garanties et re-

sponsabilités.

La page est en cours de chargement...

Malone MPG113MD Manuel utilisateur

Marque: Malone

Modèle: MPG113MD

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Malone MPG113MD User manual

Malone MPG113MD Manuel utilisateur

Malone MPG113MD Manuel utilisateur

dans d''autres langues

Documents connexes