Toyota Camry HV Le manuel du propriétaire

USER MANUAL

HANDSFREE COMMUNICATION

www.blulogicupdate.com

2

FCC Warning:

Changes or modifications not expressly approved by the party responsible for compliance could void

the user’s authority to operate the equipment.

Quick-Start Guide......................................................................4-5

Pairing Guide................................................................................6

Pairing TroubleShooting.........................................................7

Using The System......................................................................8-11

Connection..............................................................................8

Disconnection.........................................................................8

Voice Dial...............................................................................8

Call Answer............................................................................9

Call End.................................................................................9

Call Reject.............................................................................9

Last Number Re-dial.............................................................9

Mute & Un-Mute...................................................................9

Volume Adjustment................................................................9

Call Interchange..................................................................10

Call Waiting.........................................................................10

Music Stream & Pause.......................................................10

Automatic Switch between Music & calls..........................10

Sound Quality......................................................................11

Product Specication..............................................................12-13

Table of Contents

3

 CAUTION

!

Caution:

This equipment complies with FCC radiation exposure limits set forth for uncontrolled equipment

and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement Cto OET65. This

equipment has very low levels of RF energy that it deemed to comply without maximum permission

exposure evaluation (MPE). But it is desirable that it should be installed and operated with at least

20 cm and more between the radiator and person’s body (excluding extremities: hands, wrists, feet

and legs).

Co-location:

This transmitter must be not co-located or operated in conjunction with any other antenna or

transmitter.

Be Safe. When using a Hands-free cellular device in a vehicle, the vehicle operator is solely

responsible for operating the vehicle in a safe manner. Vehicle operators must maintain full

surveillance of all pertinent driving conditions at all times. An accident or collision resulting in

damage of property, personal injury, or death could occur if the operator of the vehicle fails to

pay attention to travel conditions and vehicle operation while the vehicle is in motion. Cellular

device use limits vary by state, province or locality. Obey all laws while driving.

DO NOT program, attempt to program, adjust, or set up your BLU Logic unit while the

vehicle is moving. Your vehicle should be in park with ignition turned to the on or “acc”

(accessory) position.

DO NOT program, attempt to program, adjust, or set up you BLU Logic unit while the vehicle

is inside and the engine is on.

Failure to follow the precautions could result in property damage, serious injury, and death

of yourself, pets or other people near the vehicle from carbon monoxide (for example, if the

vehicle’s engine is running in a garage with the garage door closed), or from physical impact

(if the vehicle should slip out of park and into gear with the engine running).

4

Answer Key

Down Key

Device ID

BLU Logic XXXX

Pass Key 1234

Up Key

BLU Logic is a hands-free phone system

for your vehicle. BLU Logic connects

to any hand held cell phone device

equipped with Bluetooth

®

Wireless tech-

nology hands free profile and eliminates

the need to hold a handheld cell phone,

wear a headset, earpiece, or an in vehicle

mounted hand-set adapter while making

or receiving calls.

Getting Started

First, your Hands-free equipped cell

phone must be paired or electronically

matched to the BLU Logic unit. Then

simply place your phone anywhere in the

passenger compartment of your vehicle.

Your Hands-free equipped cell phone

will automatically connect or transmit

to the BLU Logic unit every time it is

on, charged, or within range (30ft/10

meters). To Pair your phone, please see

Pairing Guide on page 6

The system can pair up to 7 hand-sets.

For a list of compatible phones please

go to http://www.blulogicupdate.com

Quick-Start Guide

5

Making and Answering Calls

To Key Do

Answer a

Call



Short Press

Ending a

Call



Short Press

Reject a

Call



Press for 2

seconds and

release when you

hear 1 beep

Redial

the Last

Number



Press for 2

seconds and

release when you

hear 1 beep

Voice

Dialing



Short Press

In a Call

To Key Do

Adjust the

Volume

Up



Short Press

Manual Pairing

To Key Do

Pairing



Press for 8 seconds

and release when

you hear 3 beeps.

The system will

enter pairing mode

for the next 5

minutes.

Memory

Erase



Press for 15

seconds and

release when you

hear 4 beeps

Adjust the

Volume

Down



Short Press

Transfer

a Call to

Handset



Press for 4

seconds and

release when you

hear 2 beeps

Call

Waiting



or



When a call waiting

tone is heard press

either volume but-

ton for 8 seconds

(approx.) to switch

to the other call.

Quick-Start Guide

6

Pairing your phone is simple, just

follow these steps:

The system can pair up to 7 hand-sets.

For a list of compatible phones please

go to http://www.blulogicupdate.com

1. Place your hand-set near the dash

board no more than 3 feet/1 meter apart.

2. Press and hold key down for 8

seconds (approximately) until you hear

3 short beeps (this puts the system into

pairing mode for 5 minutes).

3. Activate your mobile hand-set’s

Hands-free accessing function by refer-

ring to your mobile hand-set user guide

for details. The hand-set will search for

accessible Hands-free devices.

Note:

For most phones, the pairing operation

will be as follows:

Search for a new deviceNew

Handfree search. This will vary

depending on the features of your par-

ticular phone.

Pairing Guide



1

2

4. To pair another phone, repeat steps

1 through 3.

Pairing Order:

7

Pairing Order Continued:

6. Press “Return” to go back to your hand-

set’s main menu. You should, now be

able to make and receive calls through the

system within a distance of approximately

30 ft./10 meters (obstructions may cause

this distance to be shorter)

Pairing Note:

Some manufacturer’s hand-sets do

not allow automatic connection to

Hands-free devices. If your hand-set

does not connect automatically, please

check to see if the auto-connect feature

has been enabled or set to Without

Confirmation. Other possible settings

may be: Required AuthorizationNO,

Device AuthorizedYES, Connection

AuthorizedYES, or Trusted

DeviceYES.

Please refer to your hand-set’s user

manual for further details.

Pairing Guide



3

5. Select “BLU Logic XXXX” from the

list. Enter the pre-programmed passkey

“1234” and press “OK” to pair the kit and

the hand-set. When pairing is completed,

you may hear a long beep. Now the sys-

tem is in standby mode (for most mobile

hand-sets a headset icon will be shown on

the screen).

8

Cannot find the Hands-free menu:

Please refer to your hand-set user manu-

al for assistance on various phones.

Hand-set will not pair:

1. Make sure that the phone and vehicle

ignition is ON. Also make sure that the

phone battery is charged.

2. Ensure your mobile hand-set’s

Hands-free feature is activated and en-

abled. Please refer to your mobile hand-

set user guide for specific instructions.

3. Ensure the BLU Logic system is

within a maximum of 3 feet/1 meter

of your mobile hand-set and there

are no obstructions in between such

as other electronic devices (this may

cause reduced range or interference in

transmission.)

4. Delete all paired devices by momen-

tarily pressing the  key for 15 seconds.

Reference back to pairing once this is

done.

5. Your phone’s software may need to

be reset. Please remove and reinstall

battery and try again.

6. Delete all paired devices from your

hand-set and try again. There is a pos-

sibility that your hand-set is paired to too

many devices and exceeds the maximum

number of connections.

7. If all the above steps do not resolve

your problem, power off the vehicle for a

while. The BLU Logic is compliant with

and adopts the Hands-free Specification

V2.1. However, interoperability be-

tween the device and other Hands-free

enabled products is not guaranteed

because of various hand-sets features.

Please check with the manufacturer for

more information about compatibility &

use of your Hands-free devices.

The system can pair up to 7 hand-sets.

For a list of compatible phones please

go to http://www.blulogicupdate.com

My hand-set is paired with the kit.

However, when I start the car, it

doesn’t connect automatically:

Please refer to the Pairing Note men-

tioned on the left.

Pairing Troubleshooting

9

(1) Connection:

As soon as you enter the car and turn the

ignition on, the system will link with your

hand-set automatically. You will hear one

beep when the connection is established.

Important:

If it is the first time you connect your

hand-set, or your hand-set was not the

last connected to the system, please initi-

ate connection or reconnection via your

hand-set.

Note:

Whenever the Hands-free connection/link is

removed and a headset icon does not ap-

pear on the hand-set screen, please activate

connection/link as suggested (for example:

Vehicle or mobile hand-set is powered off

and then turned on; or out of 30ft/10 meter

sensing range). See your hand-set user

manual for more details.

Using The System

1 2 3

(2) Auto ConneCtion order:

The paired phone(s) will automati-

cally connect in the following order.

Only Phone 3 in car, Phone 3

connects

3

All three phones in car, Phone 1

connects

10

(B.) If the phone does not automatically

disconnect Select “disconnect” from your

hand-set menu. See your hand-set user

manual for more details.

Using The System

(1) Voice Dial:

If your mobile’s hand-set is voice dial

enabled, when in standby mode, press the

 key. When you hear a beep’ from your

hand-set, say the voice tag.

Note:

BLU Logic does not have voice dial feature

but is compatible with equipped phones.

A) Please make sure there are voice tags

recorded into the mobile hand-set before

using voice dialing function. This function

is only applicable to mobile hand-sets with

Hands-free Profile. Because of variations

among different hand-sets you may not hear

a beep. Please refer to your mobile hand-

set’s user guide for additional information.

(3) Disconnection:

Follow these steps to disconnect the kit

from the current paired hand-set.

(A) Power off the vehicle. Phone should

automatically disconnect.

Using The System

1 3

3

No Phone 2 in car, Phone 1

connects

Only Phone 3 in car, Phone 3

connects

11

B.) When streaming music, due to varia-

tions in different hand-set profiles, music

streaming may not resume after the key is

pressed.

(2) Call Answer:

Press the key to accept a call, or answer

via your mobile hand-set in the normal way.

(3) Call End:

Press the key to end a call, or end via your

mobile hand-set in the normal way.

(4) Call Reject:

Press and hold the key for 2 seconds (ap-

proximately) until you hear a short beep,

then release the key.

(5) Last Number Re-Dial:

In standby mode, press key for 2 seconds

(approx.) until you hear a short beep, then

release the key.

Note:

When streaming music, due to variations of

different hand-set profiles, music streaming

may not resume after key is pressed.

(6) Mute & Un-mute:

When a conversation is in progress, you can

mute or un-mute the microphone so that the

other party cannot hear you.

To Mute: Press and hold the keys

simultaneously for 2 seconds (approx.)

until you hear 1 beep from the speaker, then

release.

To Un-Mute: Press and hold the keys

simultaneously for 2 seconds (approx.)

until you hear 1 beep from the speaker, then

release.

(7) Volume Adjustment:

When a conversation is in progress, press

the volume upor downkeys repeatedly

until you reach the desired volume level.

Using The System

12

Using The System

Continued:

(8) Call Interchange:

When a conversation is in progress, you

may transfer the call in between the system

and hand-set.

System to Hand-set: Press key for 4 sec-

onds and release when you hear 2 beep’s.

Hand-set to System: Press key for 4

seconds and release when you hear 2 beep’s

or restart the vehicle.

Note:

This could vary owing to various hand-sets

features.

(9)Call Waiting:

When a call waiting tone is heard from your

hand-set, press either the volume up ▲or

volume down  button for

8 seconds (approx.) to switch to the other

call. Repeat the same procedure to switch

back to the first call.

(10) Music Stream & Pause:

After completion of Hands-free connec-

tion to an A2DP hand-set, you may listen

to music stored on your hand-set through

the vehicle’s speakers. Simply activate the

music streaming application on your hand-

set. Refer to your hand-set’s user manual

for more details.

Note:

Sound output is through the front speakers

only.

(11) Automatic Switch between Music

Stream & Calls:

When streaming hand-set music via the car

speakers, during an incoming call, music

will be paused. You may answer the call via

the system. Music stream will resume after

completion of the call.

13

(12) Sound Quality

For improved sound quality during BLU

Logic operation, please:

- Keep all windows up

- Avoid setting the HVAC blower speed on

high

- Avoid multiple passengers speaking at the

same time

- Project your voice clearly in the

direction of the instrument panel Sound

Quality may be effected by the following:

- Background noise

- road conditions

- vehicle speed

- wireless carrier performance

- wireless hand-set performance

Note: Sound degradation may occur with

high background noise levels in the vehicle,

including high vehicle speeds and/or road

conditions.

(13) If You need Assistance

Both Toyota and your Toyota dealer are

dedicated to serving your automotive needs.

Should you have a problem or concern

- please take the following steps

Step 1

Discuss the situation with the dealership or

customer relations manager.

Step 2

If the dealership does not address your

concern to your satisfaction, call the Toyota

Customer Experience Center at (800)

331-4331. If you are hearing- or speech-

impaired, call (800) 443-4999 (TDD).

In Canada contact our Toyota Canada

Customer Interaction

Centre at 1-888-TOYOTA-8 or

1-888-869-6828.

Care and Maintenance

(A) Do not attempt to disassemble the sys-

tem as it does not contain user serviceable

components.

(B.) Only go to designated service centers

for installation/removal of system.

(C) Do not use vinyl protectants or similar

products to clean the immediate area around

the microphone as these products will dis-

solve the microphone adhesive.

Using The System

14

Hands-free Specifications Version 2.1 + EDR; Class 2, 10 Meters/ 30 ft.

Hands-free Profile Supported HSP1.1, HFP1.5, A2DP & AVRCP Profiles

Operating Frequency Band 2.402 to 2.480GHz unlicensed ISM band

Multi-Pairing Up to 7 Hands-free devices

Hands-free DSP Full Duplex, Noise Reduction, Echo Cancellation

Power supply voltage range DC 9 ~ 25 volts

Working temperature

-25 ஂC ~ 75 ஂC / -13ஂF~ 167ஂF

Storage temperature

-35 ஂC ~ 85 ஂC / -31ஂF~ 185ஂF

Current consumption In Operation:

ACC ON (during conversation)

100mA ~2A(Max)/DC 12V

In Standby Mode:

ACC ON (standby mode) 10mA(Max)/DC 12

ACC OFF < 1mA

Product Specifications

15

Microphone

(including amplifying circuit)

Category: Omni Directional

Sensitivity: -56dB ± 2dB tolerance

SN ratio: >55dB (Min)

Frequency response: Tuned to optimize voice

response from 200Hz - 3kHz

Amplifier output

(loudspeaker)

Output power: 10W Peak

Impedance: 4 Ohm

Max output current: 3A

Max undistorted amplitude: 10Vpp

Mute mode Active Low Mute

Sink current: 40mA @ 0.5V

Dimensions (L/W/H) 134.5 x 81 x 30 mm / 5.26” x 3.19” x 1.18”

Reference # 99-9550-000 Rev. 6

Product Specifications

16

Indice

Guia de Empizo Rápido..........................................................16-17

Guia de Enlazamiento...................................................................18

Resolver Problemas de Enlazamiento.....................................19

Uso del Systema........................................................................20-22

Conexión...................................................................................20

Desconexión.............................................................................20

Marcar por voz.........................................................................20

Contestar Llamada.....................................................................21

Terminar Llamada......................................................................21

Rechazar Llamada......................................................................21

Re-marcar el Ultimo Numero......................................................21

Silenciar y Des-Silenciar............................................................21

Para Silenciar.............................................................................21

Ajuste del Volumen...................................................................21

Intercambio de llamada..............................................................22

Llamada en Espera.....................................................................22

Tocar Música & Pausa................................................................22

Cambio automatico entre transferencia de música y llamadas........22

Calidad de Sonido......................................................................23

Especificaciones del Producto.................................................24-25

Advertencia de la FCC:

Cambios o modificaciones no expresamente aprobadas por la entidad responsable por

conformidad puede causar que el usuario pierda la autoridad de operar el equipo.

17

Precaucion:

Este equipo conforma con los límites de exposición a radiación de la FCC establecidas para

equipo no controlado y conforma con la guia de exposicióna a radiofrecuencia (RF ) de

la FCC estipulada en el suplemento Cto OET65. Este equipo emite niveles muy bajos de

energía RF por el qual se considera en conformidad sin licencia de evaluación de

exposición máxima (MPE ). Sin embargo se recommienda de instalarlo y operarlo a una

distancia minima de 20cm entre el equipo radiante y el cuerpo de una persona (exclujendo

extremidades : manos , muñecas , pies y piernas ).

Co-Localización:

Este transmisor no debe de ser co - localizado o operado en conjunto con cualquier otro

antena o transmisor.

Indice

 PRECAUCION

!

Sea Seguro. Cuando se usa un aparato celular de manos libres dentro de un vehículo , el

operador del vehículo es el único responsable de manejar el vehículo en un manera segura.

Operdores de vehículos siempre tienen que mantener vigilancia entera de todos las condiciones

pertinentes al trafico. Un accidente o choque resultando en daño de propiedad, lesión personal,

o muerte podria ocurrir si el operador del vehículo falta de prestar atención a las condiciones

del traffico y las operaciónes vehiculares mientras el vehículo esta en movimiento. Límites de

uso de aparatos celulares varian entre estado, provincia o localidad. Respete todas las leyes

mientras esta manejando.

NO: Programar, intentar de programar, ajustar o habilitar su unidad ‘BLU Logic’ mientras

el vehículo esta en movimiento. Su vehículo debe estar con el selector de velocidades en

posicion de estacionamiento y la llave de ignicion en encendido o auxiliar.

NO: Programar, intentar de programar, ajustar o habilitar su unidad ‘BLU Logic’ mientras el

vehículo esta encerrado con el motor encendido.

Falla de seguir las precauciones podria resultar en daños materiales, lesiónes graves, y muerte

de usted, animales domésticos u otras personas cerca del vehículo causado por monóxido de

carbono ( por ejemplo , si el motor del vehículo esta encendido en un garage con la puerta del

garage cerrado ), o por un impacto físico ( si el cambio de velocidades brinca de estacionado

a marcha con el motor andando ).

18

Comienzo

Para empezar su celular de manos libres

tiene que ser enlazado or electrónica-

mente connectado con la unidad BLU

Logic. Simplemente ponga su telefono

en qualquier lugar dentro del area de

passajeros del vehículo. Su cellular eq-

uipado con la function de manos libres

automaticamente conecta o transmite

con la unidad BLU Logic siempre que

esté encendido, cargando, o dentro del

alcance de alcance (30pies/10metros).

Identificacion

del aparato

BLU Logic XXXX

Llave de paso 1234

BLU Logic es un sistema telefonico de

manos libres para su vehiculo. BLU Logic

connecta con cualquier telefono cellular

equipado con perfil de manos libres de tec-

nologia inalámbrica Bluetooth

®

y elimina

la necesidad de sostener el celular, usar

audiphonos, auricular, o un adaptador de

cellular montado en el vehiculo mientras

usted haga o reciba llamadas.

Hacer y Contestar Llamadas

Para Botón Haga

Contestar

una

llamada



Oprima

brevemente

Terminar

una

llamada



Oprima

brevemente

Rechazar



Oprima por 2

segundos y suelte

cundo escuche 1

sonido ‘beep’

Re-marcar

el ultimo

numero



Oprima por 2

segundos y suelte

cundo escuche 1

sonido ‘beep’

Marcar por

voz



Oprima

brevemente

Para enlazar su telefono, favor de ver la

guia de enlazamiento en pagina 3.

El sistema puede enlazar hasta 7 celulares.

Para una lista de telefonos compatibles

fovor de visitar

http://www.blulogicupdate.com

Guia de Empizo Rápido

19

Durante una Llamada

Para Botón Haga

Incrementar el

volumen



Oprima

brevemente

Disminuir el

volumen



Oprima

brevemente

Pasar una

llamada al

celular



Oprima por

4 segundos

y suetelo cu-

ando escuche

2 sonido

‘beep’s

Llamada en

espera



ó



Cuando

escuche un

tono indicador

de llamada

esperando

presione uno

de los botones

de volumen

por 8 segun-

dos (approx.)

para cambiar

de llamada

Enlazaminto Manual

Para Botón Haga

Enlazar



Oprima por

8 segundos y

sueltelo cu-

ando escuche 3

sonido ‘beep’s.

El sistema

entra al modo

de enlazamiento

por los proxi-

mos 5 minutos

Borrar la

memoria



Oprima por

15 segundos

y sueltelo

cuando escuche

4 sonido ‘beep’s

Botón de

Contestar

Botón de Bajar

Botón de Subir

Guia de Empizo Rápido

20

Enlazar su telefono es simpe, solamente

siga estos pasos:

El sistema puede enlazar hasta 7 celulares.

Para una lista de teléfonos compatibles

favor de visitar

http://www.blulogicupdate.com

1. Ponga su celular cerca del tablero a una

distancia no mas lejos de 3 pies/1 metros.

2. Oprima el botón 

 por 8 segundos

(aproximadamente) hasta que escuche 3

sonido ‘beep’s (esto pone el sistema en el

modo de enlazamiento por 5 minutos)

3. Active la función de acceso a manos

libres de su celular, referiendo al manual de

operación de su celular para mas detalles. El

celular automaticamente buscara aparatos ac-

cesibles de manos libres ‘Hands-free’.

Nota:

Para la mayoria de teléfonos la operación de

enlacamiento sera como sigue:

Busca por un aparato nuevo Nuevo

Busqueda de manos libres ‘Hands-

free’. Esto varía dependiendo de las funciones

de su teléfono.

4. Seleccione “BLU Logic XXXX” de la

lista. Marque la llave de paso pre-progamada

“1234” y oprima “OK” para enlacar el aparato

con su celular. En cuanto el enlazamiento ha

Guia de Enlazamiento

sido completado podra escuchara un sonido

‘beep’ largo. Ahora el sistema está en el modo

de espera (en la mayoria de celulares un sim-

bolo de audifono sera visible en la pantalla).

5. Oprima “Regresar” para retornar al menú

principal de su celular. Ahora usted deberia

poder hacer y recibir llamadas atraves del

sistema dentro de un alcance de aproxi-

madamente 30 pies/10 metros (obstrucciones

podrian reducir esta distancia).

Nota de Enlazamiento:

Celulares de algunos fabricantes no permiten

la conexión automatica a aparatos de manos

libres ‘Hands-free’. Si su celular no conecta

automaticamente, favor de checar que la

función de auto-conectar esté operacional o

puesta a “sin confirmación”. Otros ajustes

possibles son: Autorización requerida 

NO, Aparato autorizado  SI, Connexión

autorizada  SI, o Aparato de confianza

 SI.

Favor de referir al manual de operación de su

celular para mas detalles.

La page charge ...

Toyota Camry HV Le manuel du propriétaire

Toyota Camry HV Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents