IKEA IHW6302VM0 Guide d'installation

Marque: IKEA

Modèle: IHW6302VM0

Catégorie: Hottes

Taper: Guide d'installation

Ce manuel convient également à

|KEA ®

30" (76 CM) AND 35T,46'' (90 CM)-

WALL-MOUNT CANOPY RANGE HOOD

_ _ ___,_u÷_i___._,_ _o o_o __,,_._,,,,,_,_4i_o__4__ U$@'_....._ ¢_:_,,.u_@_ ¸_......_':_J_,_UI_'_'......__

For questions about features, operation/performance, parts, accessories or service, call: 1-866-664-2449.

In Canada, for assistance, installation and service, call: 1-866-664-2449.

HOTTEDECUISINIERE POUR MONTAGE MURAL

30" (76 CM) ET357,46"(90 CM)

Au Canada, pour assistance, installation ou service, composez le 1-866-664-2449.

Table of Contents/Table des matieres ............................................................................. 2

iMPORTANT: READ AND SAVE THESE INSTRUCTIONS.

FOR RESIDENTIAL USE ONLY.

iMPORTANT : URE ET CONSERVER CES iNSTRUCTiONS.

POUR UTJUSATJON RESiDENTiELLE UNJQUEMENT.

W10177452B

TABLEOF CONTENTS

RANGE HOOD SAFETY ................................................................. 2

INSTALLATION REQUIREMENTS ................................................ 3

Tools and Parts ............................................................................ 3

Location Requirements ................................................................ 4

Venting Requirements (vented models only) ............................... 5

Electrical Requirements ............................................................... 6

INSTALLATION INSTRUCTIONS .................................................. 6

Prepare Location .......................................................................... 6

Install Range Hood ....................................................................... 8

Connect Vent System .................................................................. 8

Make Electrical Connection ......................................................... 8

Install Vent Covers ....................................................................... 9

Install Filters .................................................................................. 9

Complete Installation ................................................................... 9

RANGE HOOD USE ........................................................................ 9

RANGE HOOD CARE ................................................................... 10

Cleaning ...................................................................................... 10

WIRING DIAGRAM ...................................................................... 11

ASSISTANCE OR SERVICE ......................................................... 12

In the U.S.A................................................................................ 12

In Canada ................................................................................... 12

Accessories ................................................................................ 12

WAR RANTY .................................................................................. 12

TABLEDESMATIERES

SECURITE DE LA HOTTE DE CUlSINIERE ............................... 14

EXIGENCES D'INSTALLATION ................................................... 16

Outillage et pieces ...................................................................... 16

Exigences d'emplacement ......................................................... 16

Exigences concernant I'evacuation ........................................... 17

Specifications electriques .......................................................... 18

INSTRUCTIONS D'INSTALLATION ............................................. 19

Preparation de I'emplacement ................................................... 19

Installation de la hotte ................................................................ 21

Installation du conduit d'evacuation .......................................... 21

Raccordement electrique ........................................................... 21

Installation du cache-conduit ..................................................... 22

Installation des filtres .................................................................. 22

Achever I'installation .................................................................. 22

UTILISATION DE LA HOTTE ....................................................... 23

ENTRETIEN DE LA HOTTE .......................................................... 23

Nettoyage et entretien................................................................ 23

SCHI_MA DE C.&,BLAGE............................................................... 25

ASSISTANCE OU SERVICE ......................................................... 26

Accessoires ................................................................................ 26

GARANTIE ..................................................................................... 27

RANGE HOOD SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

iMPORTANT SAFETY iNSTRUCTiONS

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK, OR INJURY TO PERSONS, OBSERVE THE

FOLLOWING:

• Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the

manufacturer.

• Before servicing or cleaning the unit, switch power off at

service panel and lock the service disconnecting means to

prevent power from being switched on accidentally. When

the service disconnecting means cannot be locked,

securely fasten a prominent warning device, such as a tag,

to the service panel.

• Installation work and electrical wiring must be done by

qualified person(s) in accordance with all applicable codes

and standards, including fire-rated construction.

• Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of fuel

burning equipment to prevent backdrafting. Follow the

heating equipment manufacturer's guideline and safety

standards such as those published by the National Fire

Protection Association (NFPA), the American Society for

Heating, Refrigeration and Air Conditioning Engineers

(ASHRAE), and the local code authorities.

• When cutting or drilling into wall or ceiling; do not damage

electrical wiring and other utilities.

• Ducted fans must always be vented outdoors.

CAUTION: For general ventilating use only. Do not use

to exhaust hazardous or explosive materials and vapors.

CAUTION: To reduce risk of fire and to properly exhaust

air, be sure to duct air outside - do not vent exhaust air into

spaces within walls or ceilings, attics or into crawl spaces,

or garages.

WARNING: TO REDUCE THE RISK OF FIRE, USE ONLY

METAL DUCTWORK.

WARNING: TO REDUCE THE RISK OF A RANGE TOP

GREASE FIRE:

[] Never leave surface units unattended at high settings.

Boilovers cause smoking and greasy spillovers that may

ignite. Heat oils slowly on low or medium settings.

[] Always turn hood ON when cooking at high heat or when

flambeing food (i.e. Crepes Suzette, Cherries Jubilee,

Peppercorn Beef Flamb6).

[] Clean ventilating fans frequently. Grease should not be

allowed to accumulate on fan or filter.

[] Use proper pan size. Always use cookware appropriate for

the size of the surface element.

WARNING: TO REDUCE THE RISK OF INJURY TO

PERSONS IN THE EVENT OF A RANGE TOP GREASE

FIRE, OBSERVE THE FOLLOWING: a

[] SMOTHER FLAMES with a close fitting lid, cookie sheet, or

metal tray, then turn off the burner. BE CAREFUL TO

PREVENT BURNS. If the flames do not go out

immediately, EVACUATE AND CALL THE FIRE

DEPARTMENT.

[] NEVER PICK UP A FLAMING PAN - you may be burned.

[] DO NOT USE WATER, including wet dishcloths or towels -

a violent steam explosion will result.

[] Use an extinguisher ONLY if:

- You know you have a class ABC extinguisher, and you

already know how to operate it.

- The fire is small and contained in the area where it

started.

- The fire department is being called.

- You can fight the fire with your back to an exit.

aBased on "Kitchen Fire Safety Tips" published by NFPA.

[] WARNING: To reduce the risk of fire or electrical shock,

do not use this fan with any solid-state speed control

device.

SAVE THESE iNSTRUCTiONS

INSTALLATIONREQUIREMENTS

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools needed

• Level

• Drill with 11¼"(3.0 cm), 3/8"(9.5 mm), %4" (2.75 mm) and

1/8"(3.0 mm) drill bits

• Pencil

• Wire stripper or utility knife

• Tape measure or ruler

• Pliers

• Caulking gun and weatherproof caulking compound

• Vent clamps

• Jigsaw or keyhole saw

• Flat-blade screwdriver

• Metal snips

• Phillips screwdriver

• Metric Allen wrench set

Parts needed

• Home power supply cable

• Two 1/2"(12.7 mm) UL listed or CSA approved strain reliefs

• 3 UL listed wire connectors

For vented installations, you will also need:

• 1 wall or roof cap

• Metal vent system

For non-vented (recirculating) installations, you will also

need:

• Charcoal Filter Kit Part Number 4396848 for non-vented

(recirculating) installations only. See "Assistance or Service"

section to order.

Parts supplied

Remove parts from packages. Check that all parts are included.

• Hood canopy assembly with ventilator and light bulbs

installed

• Deflector for non-vented (recirculating) installations

• Vent transition with back draft dampers installed

• Filter(s) - depending on model and size

• 2 mounting hooks

• Vent cover support bracket

• Mounting template

• 2-piece vent cover

• Rubber tape

• 2 - 2.9 x 6.5 mm screws

• 2 - 3.5 x 6.5 mm screws

• 2 - 3.5 x 9.5 mm screws

• 2 - 6.0 x 70.0 mm screws

• 6 - 5.0 x 35.0 mm mounting screws

• 2 - 10.0 x 60.0 mm drywall anchors

• Allen wrench for Torx_t head screws

IMPORTANT: Observe all governing codes and ordinances.

Have a qualified technician install the range hood. It is the

installer's responsibility to comply with installation clearances

specified on the model/serial rating plate. The model/serial rating

plate is located behind the left filter on the rear wall of the vent

hood.

Canopy hood location should be away from strong draft areas,

such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used. Given

dimensions provide minimum clearance.

Grounded electrical outlet is required. See "Electrical

Requirements" section.

The canopy hood is factory set for venting through the roof or

wall. For non-vented (recirculating) Installation see "Non-vented

(recirculating) Installations" in "Prepare Location" section.

Charcoal Filter Kit Part Number 4396848 is available from your

dealer or an authorized parts distributor.

All openings in ceiling and wall where canopy hood will be

installed must be sealed.

For Mobile Home Installations

The installation of this range hood must conform to the

Manufactured Home Construction Safety Standards, Title 24

CFR, Part 328 (formerly the Federal Standard for Mobile Home

Construction and Safety, Title 24, HUD, Part 280) or when such

standard is not applicable, the standard for Manufactured Home

Installation 1982 (Manufactured Home Sites, Communities and

Setups) ANSI A225.1/NFPA 501A*, or latest edition, or with local

codes.

Product Dimensions

Installation Dimensions

61/2"

(16.5 cm)

'%, _r-..........._ 2" (5.1 cm) rain.

"_ -=.-_---:;:---:-_--_.-.. 9" (22.9 cm) rain*

Side

cabinet

Side

cabinet

*For non-vented (recirculating) installations

I"®TORX is a registered trademark of Acument Intellectual Properties, LLC.

• Vent system must terminate to the outdoors, except for non-

vented (recirculating) installations. Roof Venting Wall Venting

• Do not terminate the vent system in an attic or other enclosed

area.

• Do not use 4" (10.2 cm) laundry-type wall cap.

• Use metal vent only. Rigid metal vent is recommended.

Plastic or metal foil vent is not recommended.

• The length of vent system and number of elbows should be

kept to a minimum to provide efficient performance.

For the most efficient and quiet operation:

• Use a straight run or as few elbows as possible.

• Use no more than three 90° elbows.

• Make sure there is a minimum of 24" (61.0 cm) of straight

vent between the elbows if more than 1 elbow is used.

• Do not install 2 elbows together.

Non-vented

(recirculating)

Use clamps to seal all joints in the vent system.

The vent system must have a damper. If the roof or wall cap

has a damper, do not use the damper supplied with the range

hood.

• Use caulking to seal exterior wall or roof opening around the

cap.

• The size of the vent should be uniform.

Cold weather installations

An additional back draft damper should be installed to minimize

backward cold air flow and a thermal break should be installed to

minimize conduction of outside temperatures as part of the vent

system. The damper should be on the cold air side of the thermal

break.

A. Roof cap A. Wall cap A. Deflector

B. 6" (15.2 cm) B. 6" (15.2 cm) B. 6" (15.2 cm)

round vent round vent round vent

Calculating Vent System Length

To calculate the length of the system you need, add the

equivalent feet (meters) for each vent piece used in the system.

Vent Piece 6" (15.2 cm) Round

45° elbow 2.5 ft

(0.8m)

The break should be as close as possible to where the vent

system enters the heated portion of the house.

Makeup air

Local building codes may require the use of makeup air systems

when using ventilation systems greater than specified CFM of air

movement. The specified CFM varies from locale to locale.

Consult your HVAC professional for specific requirements in your

area.

90° elbow 5.0 ft

(1.5m)

Maximum equivalent vent length is 35 ft (10.7 m).

Venting Methods

This canopy hood is factory set for venting through the roof or

wall.

A 6" (15.2 cm) round vent system is needed for installation (not

included). The hood exhaust opening is 6" (15.2 cm) round.

NOTE: Flexible vent is not recommended. Flexible vent creates

back pressure and air turbulence that greatly reduce

performance.

Vent system can terminate either through the roof or wall. To vent

through a wall, a 90° elbow is needed.

Rear discharge

A 90° elbow may be installed immediately above the hood.

For non-vented (recirculating) installations

If it is not possible to vent cooking fumes and vapors to the

outside, the hood can be used in the non-vented (recirculating)

version, fitting an activated carbon filter and the deflector. Fumes

and vapors are recycled through the top grille.

Example vent system

The following example falls within the maximum vent length of

35 ft (10.7 m).

1 - 90 ° elbow = 5.0 ft (1.5 m)

1 - wall cap = 0.0 ft (0.0 m)

8 ft (2.4 m) straight = 8.0 ft (2.4 m)

Length of system = 13.0 ft (3.9 m)

Observeallgoverningcodesandordinances.

Ensurethattheelectricalinstallationisadequateandin

conformancewithNationalElectricalCode,ANSI/NFPA70(latest

edition),orCSAStandardsC22.1-94,CanadianElectricalCode,

Part1andC22.2No.0-M91(latestedition)andalllocalcodes

andordinances.

Ifcodespermitandaseparategroundwireisused,itis

recommendedthataqualifiedelectriciandeterminethatthe

groundpathisadequate.

Acopyoftheabovecodestandardscanbeobtainedfrom:

NationalFireProtectionAssociation

OneBatterymarchPark

Quincy,MA02269

CSAInternational

8501EastPleasantValleyRoad

Cleveland,OH44131-5575

• A 120 Volt, 60 Hz., AC only, 15-amp, fused electrical circuit is

required.

• If the house has aluminum wiring follow the procedure below:

1. Connect a section of solid copper wire to the pigtail

leads.

2. Connect the aluminum wiring to the added section of

copper wire using special connectors and/or tools

designed and UL listed for joining copper to aluminum.

Follow the electrical connector manufacturer's recommended

procedure. Aluminum/copper connection must conform with

local codes and industry accepted wiring practices.

• Wire sizes and connections must conform with the rating of

the appliance as specified on the model/serial rating plate.

The model/serial plate is located behind the filter on the rear

wall of the hood.

Wire sizes must conform to the requirements of the National

Electrical Code, ANSI/NFPA 70 (latest edition), or CSA

Standards C22.1-94, Canadian Electrical Code, Part 1 and

C22.2 No. 0-M91 (latest edition) and all local codes and

ordinances.

INSTALLATIONINSTRUCTIONS

• Before making cutouts, make sure there is proper clearance

within the ceiling or wall for exhaust vent.

• Check your ceiling height and the hood height maximum

before you select your hood.

1. Disconnect power.

2. Determine which venting method to use: roof, wall, or non-

vented.

3. Select a flat surface for assembling the range hood. Place

covering over that surface.

It is recommended that the vent system be installed before 7. Tape template in place, aligning the template centerline and

hood is installed, bottom of template with hood bottom line and with the

centerline marked on the wall.

Excessive Weight Hazard

Use two or more people to move and install

range hood.

Failure to do so can result in back or other injury.

A. Centerline

B. Mounting hook location

C. Fastener locations

D. Mounting height reference

4. Using 2 or more people, lift range hood onto covered surface.

Range Hood Mounting Screws Installation

Determine and mark the centerline on the wall where the

canopy hood will be installed.

Select a mounting height between a minimum of

30" (76.2 cm) and a suggested maximum of 36" (91.4 cm),

above the range to the bottom of the hood and mark

reference line on the wall.

NOTE: For installation locations with reduced ceilings

heights, the vent hood may be installed using the upper vent

cover for both vented and non-vented (recirculating)

installations.

8. Mark centers of the 6 fastener locations through the template

to the wall.

IMPORTANT: All screws must be installed into wood.

Remove the template.

9. Drill %4" (2.75 mm) pilot holes at all locations where screws

are being installed into wood.

10. Attach two mounting hooks to the wall at location marked on

the template.

A B

......................i ........

A. Mounting hooks

B. Centerline on wall

Vent Cover Support Bracket Installation

Installations using telescoping upper and lower vent cover

assembly

1. Position vent cover bracket on wall about 1/8"(3.0 mm) away

from the ceiling.

2. Mark the hole locations.

3. Drill 3/8"(9.5 mm) holes for wall anchors and insert anchors

flush with the wall.

, A

e-.. e _::D ................ C

A. 10.0 x 60.0 mm drywall anchors

B. Centerline on wall

C. Vent cover support bracket

D. 6.0 x 70.0 mm screws

4. Attach vent cover support bracket to wall.

Installation locations with reduced ceiling heights

NOTE: Either the lower or the upper vent cover can be used for

such installation but note that upper vent cover is smaller than

the lower vent cover. There will be more clearance were the upper

vent cover attaches on top of the range hood.

For non-vented (recirculating) installations:

The vent hood is installed using the upper vent cover

(26" [66.0 cm]) plus a %" (10.0 mm) thick wood filler.

1. For the vent cover to slide down and engage the top of the

hood, the vent cover bracket must be installed 2/8"(10.0 mm)

below the ceiling.

2. The remaining space above the vent cover can be filled with a

2/8"(10.0 mm) thick piece of plywood cut to the inside cross

section of the chimney cover and finished to match the

ceiling.

For vented installations:

The vent hood is installed using the lower vent cover

(163/4"[42.5 cm]) plus a 2/8"(10.0 mm) thick wood filler.

1. For the vent cover to slide down and engage the top of the

hood, the vent cover bracket must be installed 2/8"(10.0 mm)

below the ceiling.

2. The remaining space above the vent cover can be filled with a

2/8"(10.0 mm) thick piece of plywood cut to the inside cross

section of the chimney cover and finished to match the

ceiling.

Cut the self adhesive rubber tape supplied with the hood in 4

identical pieces. Attach 2 pieces of tape to each side of the

support bracket.

_ ..................................S

A. Vent cover bracket

B. Rubber tape

Vented Installations

Install transition on top of hood (ifremoved for shipping) with

2 sheet metal screws.

Non-Vented (recirculating) Installations

1. Install transition on top of hood (if removed for shipping) with

2 sheet metal screws.

2. Attach the vent cover ceiling bracket to the deflector with the

two 3.5 x 9.5 mm screws provided.

A. Vent cover bracket

B. 3.5 x 9.5 mm screws

C. Deflector

3. Connect the deflector to the transition with 6" (15.2 cm)

round vent once hood has been set in place.

Complete Preparation

1. Determine and make all necessary cuts in the wall for the vent

system. Install the vent system before installing the hood. See

"Venting Requirements" section.

2. Determine the required height for the 1/2"conduit and drill a

1V4"(3.2 cm) hole at this location.

3. Run wire through the 1/2"conduit according to the National

Electrical Code or CSA Standards and local codes and

ordinances. There must be enough 1/2"conduit and wires from

the fused disconnect (or circuit breaker) box to make the

connection in the hood's electrical terminal box.

NOTE: Do not reconnect power until installation is complete.

4. Use caulk to seal all openings.

f"s cl Hoo£

Excessive Weight Hazard

Use two or more people to move and install

range hood.

Failure to do so can result in back or other injury.

Using 2 or more people, hang range hood on 2 mounting

hooks through the rectangular cutouts on back of hood.

A. Mounting hooks

B. 5 x 35 mm mounting screws

C. Leveling screws

D. Centerline on wall

2. Level the hood with leveling screws in mounting hooks or

rectangular cutouts, using a level across bottom of hood.

3. Secure hood with 4 screws through remaining 4 holes in

hood.

Fit vent system over transition piece.

Mc <® E ccl Connect on

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

Disconnect power.

Remove terminal box cover.

Remove the knockout in the terminal box cover and install a

UL listed or CSA approved W' strain relief.

Run 3 wires, black, white and green (14AWG), in W' conduit

from service panel to terminal box. Use caulking to seal

opening.

D E F

A. UL listed or CSA approved strain relief

B. Home power supply cable

C. Terminal box

D. Black wires

E. Green (or bare) wire connected to yellow-green wire

F. White wires

Use UL listed wire connectors and connect black wires (D)

together.

A. Vent transition

B. 3.5 x 6.5 mm screw

2. Seal connection with clamps.

6. Use UL listed wire connectors and connect white wires (F)

together.

Electrical Shock Hazard

Electricaly ground blower.

Connect ground wire to green and yellow ground wire

in terminal box.

Failure to do so can result in death or electrical shock.

7. Connect green (or bare) ground wire from home power supply

to yellow-green ground wire (E)in terminal box using UL listed

wire connectors.

8. Tighten strain relief screw.

9. Install terminal box cover.

10. Check all light bulbs to make sure they are secure in their

sockets.

11. Reconnect power.

n C

When using both upper and lower vent covers, push lower cover

down onto hood and lift upper cover to ceiling and install with

two 2.9 x 6.5 mm screws.

NOTE: Upper vent cover may be reversed to hide slots.

C .......................A

...........................S

A. Upper vent cover

B. Lower vent cover

C. 2.9 x 6.5 mm screws

D. Bracket

For reduced ceiling height installations, using the upper cover fix

it to its bracket, using the lower vent cover, push cover down

onto hood and snap vent into place around vent cover bracket.

For non-vented (recirculating installations, install charcoal

filter over grille on blower housing and turn filter handle

clockwise. Repeat with other charcoal filter.

A. Blower housing

B. Filter handle

C. Charcoal filters

2. For all installations, insert back edge or metal filter into rear

channel of the filter opening.

3. Push handle toward the rear and push filter up.

4. Pull filter toward the front and insert into front channel.

Compete ....

Check Range Hood Operation

1. Move the light switch to "1" position. The light should turn on.

2. Move blower switch to "1" position. The blower should

operate.

3. Move the blower speed switch to "1" position for low speed,

"2" position for medium speed or "3" position for high speed.

4. Move blower and light switches to "0" position to turn off

blower and light.

5. If range hood does not operate, check to see whether a

circuit breaker has tripped or a household fuse has blown.

NOTE: To get the most efficient use from your new range hood,

read the "Range Hood Use" section.

RANGE HOOD USE

The range hood is designed to remove smoke, cooking vapors

and odors from the cooktop area. For best results, start the hood

before cooking and allow it to operate several minutes after the

cooking is complete to clear all smoke and odors from the

kitchen.

Control Panel

The range hood controls are located on the front side of the

canopy.

..........S

A. Light switch

B. Blower switch

Operating the Light

1. Move the light switch to the "1" position to turn on the light.

2. Move the light switch to the "0" position to turn off the light.

Operating the Blower and Adjusting Blower Speed

1. Move the blower switch to the "1" position for low speed, the

"2" position for medium speed or the "3" position for high

speed.

2. Move the blower switch to the "0" position to turn off the

blower.

RANGE HOOD CARE

5. Install charcoal filter over grille on blower housing and turn

filter handle clockwise.

IMPORTANT: Clean the hood and grease filters frequently

according to the following instructions. Replace grease filters

before operating hood.

Be sure lights are cool before cleaning the hood.

Exterior Surfaces

Clean the range hood with a mild detergent and soft cloth. To

avoid damage to the exterior surface, do not use abrasive

cleanser or steel-wool pads.

Metal Grease Filters

The filters should be washed frequently. Place metal filters in

dishwasher or hot detergent solution to clean.

Drain water through edge holes and let each filter dry thoroughly

before replacing it.

To Remove Metal Grease Filters

1. Turn off fan and lights. Check that halogen lamp is cool.

2. Push handle toward the rear and pull downward.

3. Pull filter toward the front.

A. Blower housing

B. Filter handle

C. Charcoal filters

6. Repeat to install other charcoal filter.

7. Replace metal grease filters. See "Metal Grease Filters"

section.

To Replace Charcoal Filters

1. Turn fan and lights off. Check that halogen lamp is cool.

2. Remove the metal grease filters. See "Metal Grease Filters"

section.

3. Turn charcoal filter counterclockwise.

4. Remove and discard both charcoal filters.

5. Install replacement charcoal filters over grille in blower

housing and turn filter handle clockwise.

6. Replace metal grease filters. See "Metal Grease Filters"

section.

To Replace Metal Grease Filters

1. Insert back edge of filter into rear channel of the filter

opening.

2. Push handle toward the rear and push filter up.

3. Pull filter toward the front and insert into front channel.

Charcoal Filters - For Non-Vented (recirculating)

Installations

The charcoal filters are not washable nor reusable.

They should be changed every 6 months in normal use.

The charcoal filters capture unpleasant cooking odors.

To Install Charcoal Filters

1. Turn fan and lights off. Check that halogen lamp is cool.

2. Remove the metal grease filters. See "Metal Grease Filters"

section.

3. Set metal grease filter aside.

4. Repeat to remove other metal grease filter.

Replacing a Halogen Lamp

Turn off the range hood and allow the halogen lamp to cool. To

avoid damage or decreasing the life of the new bulb, do not

touch bulb with bare fingers. Replace bulb, using tissue or

wearing cotton gloves to handle bulb.

If new lights do not operate, make sure the lamps are inserted

correctly before calling service.

1. Disconnect power.

2. Use a flat-blade screwdriver and gently pry the light cover

loose.

3. Remove the lamp and replace with a 12-volt, 20-watt

maximum, halogen lamp made for a G-4 base.

4. Replace the light cover.

WIRING DIAGRAM

SLM,SLS

OFF 1 2 3

2-4 4-6 6-8 8-10

1-3 3-5 5-7 7-9

SLL

0 1

2-4 4-6

1-3 3-5

SE1L7B

YEL

<rr

LLI

frO >

I-U_

m "n RED

_::_[_//_. RED

/__ BLK

o 6 6 %

2 4 6 8_

ol SLTS

YEL

BLK

BRW

WHT

LLI

o 6 6

I1 3 51_

BRW /

GRN _

Y-G

WIRING BOX

MOTOR CONNECTIONS OHMRESISTENCE

SPEED TOTERMINALS BETWEENTERMINALS

RED-BLACK

1 338

Jumper: YELLOW-WHITE

RED-YELLOW

2 Jumper: YELLOW-WHITE 184

RED-YELLOW

3 a"umper: YELLOW-BLACK 261

O O

COLORTABLE

BLK BLACK

BLU BLUE

BRW BROWN

GRN GREEN

GRY GRAY

-=N

COLOR TABLE

RED RED

WHT WHITE

YEL YELLOW

Y-G YELLOW/GREEN

ASSISTANCEOR SERVICE

When calling for assistance or service, please know the purchase

date and the complete model and serial number of your

appliance. This information will help us to better respond to your

request.

If you need replacement parts

If you need to order replacement parts, we recommend that you

use only factory specified parts. Factory specified parts will fit

right and work right because they are made with the same

precision used to build every new IKEA® appliance.

To locate factory specified parts in your area, call us or your

nearest designated service center.

n _e USA_

Call the Whirlpool Customer eXperience Center

toll free: 1-866-664-2449.

Our consultants provide assistance with:

• Features and specifications on our full line of appliances.

• Installation information.

• Use and maintenance procedures.

• Accessory and repair parts sales.

• Specialized customer assistance (Spanish speaking, hearing

impaired, limited vision, etc.).

• Referrals to local dealers, repair parts distributors, and

service companies. Whirlpool designated service technicians

are trained to fulfill the product warranty and provide after-

warranty service, anywhere in the United States.

To locate the Whirlpool designated service company in your

area, you can also look in your telephone directory Yellow

Pages.

For further assistance

If you need further assistance, you can write to Whirlpool

Corporation with any questions or concerns at:

IKEA Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

Please include a daytime phone number in your correspondence.

GdG

Call the Whirlpool Canada LP Customer eXperience Centre toll

free: 1-866-664-2449.

Our consultants provide assistance with:

• Features and specifications on our full line of appliances.

• Use and maintenance procedures.

• Accessory and repair parts sales.

• Referrals to local dealers, repair parts distributors, and

service companies. Whirlpool Canada LP designated service

technicians are trained to fulfill the product warranty and

provide after-warranty service, anywhere in Canada.

For further assistance

If you need further assistance, you can write to Whirlpool

Canada LP with any questions or concerns at:

Customer eXperience Centre

Whirlpool Canada LP

1901 Minnesota Court

Mississauga, Ontario L5N 3A7

Please include a daytime phone number in your correspondence.

Charcoal Filter Kit

(for non-vented installations only)

Order Part Number 4396848

IKEAMAJOR APPLIANCEWARRANTY

How long is the IKEA limited warranty valid?

This limited warranty is valid for five years from the date of purchase, when this major appliance is operated and maintained according

to instructions attached to or furnished with the product, unless the appliance is named LAGAN in which case this limited warranty is

valid for one year from the date of purchase. This limited warranty is valid only in the United States or Canada and applies only when the

major appliance is used in the country in which it was purchased. Proof of original purchase date is required to obtain service under this

limited warranty.

Which appliances are not covered by the IKEA five (5) year limited warranty?

For major appliances named "LAGAN", this limited warranty is valid for one year from the date of purchase.

Who will execute the service?

This limited warranty is provided by Whirlpool Corporation or Whirlpool Canada LP (hereafter "Whirlpool"). Service must be provided by

a Whirlpool designated service company.

What does this limited warranty cover?

The limited warranty will pay for factory specified parts and repair labor to correct defects in materials or workmanship that existed

when the major appliance was purchased. The exceptions are specified under the headline "What is not covered under this limited

warranty?".

What will be done to correct the problem?

The designated service company will examine the product and decide, at its sole discretion, if it is covered under this limited warranty.

If considered covered, the designated service company will then repair the defect. Your sole and exclusive remedy under this limited

warranty shall be product repair as provided herein.

What is not covered under this limited warranty?

• Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or

repair house fuses, or to correct house wiring or plumbing.

• Service calls to repair or replace appliance light bulbs, air filters or water filters. Consumable parts are excluded from warranty

coverage.

• Replacement parts or repair labor if this major appliance is used for other than normal, single-family household use or when it is used

in a manner that is inconsistent to published user or operator instructions and/or installation instructions.

• Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in

accordance with electrical or plumbing codes, or use of consumables or cleaning products not approved for use.

• Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage

results from defects in materials or workmanship and is reported within 30 days from the date of purchase.

• Any food loss or medicine loss due to refrigerator or freezer product failures.

• Pick up and delivery. This major appliance is intended to be repaired in your home.

• Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

• Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an

authorized servicer is not available.

• The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance with

published installation instructions.

• Replacement parts or repair labor on major appliances with original model/serial numbers that have been removed, altered or cannot

be easily determined.

The cost of repair or replacement under these excluded circumstances shall be borne by the customer.

Disclaimer of Implied Warranties

IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR

A PARTICULAR PURPOSE, ARE LIMITED TO FIVE YEARS (ONE YEAR FOR MAJOR APPLIANCES NAMED "LAGAN") OR THE

SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces do not allow limitations on the duration of implied warranties of

merchantability or fitness, so this limitation may not apply to you. This warranty gives you specific legal rights, and you also may have

other rights that vary from state to state or province to province.

Limitation of Remedies; Exclusion of Incidental and Consequential Damages

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.

WHIRLPOOL SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow

the exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This

warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.

How to reach us if you need our service

If outside the 50 United States and Canada, contact your authorized IKEA retailer to determine if another warranty applies.

If you need service, please read the Installation Instructions and/or the "Troubleshooting" section of the Use & Care Guide before

contacting us. Ifyou need additional help, do not hesitate to contact us in the U.S.A. and Canada at 1-866-664-2449. 2/09

Keep this book and your sales slip together for future

reference. You must provide proof of purchase or installation

date for in-warranty service.

Write down the following information about your major appliance

to better help you obtain assistance or service if you ever need it.

You will need to know your complete model number and serial

number. You can find this information on the model and serial

number label located on the product.

Dealer name

Address

Phone number

Model number

Serial number

Purchase date

SECURITEDELA HOTTEDECUlSlNIERE

Votre securite et celle des autres est tres importante.

Nous donnons de nombreux messages de s_curit_ importants dans ce manuel et sur votre appareil m_nager. Assurez-vous de

toujours lire tousles messages de s_curit_ et de vous y conformer.

Voici le symbole d'alerte de s_curit&

Ce symbole d'alerte de s_curit_ vous signale les dangers potentiels de d_c_s et de blessures graves &vous

et &d'autres.

Tousles messages de s_curit_ suivront le symbole d'alerte de s_curit_ et le mot "DANGER" ou

"AVERTISSEMENT". Ces mots signifient •

Risque possible de d_cbs ou de blessure grave si vous ne

suivez pas imm_diatement les instructions.

Risque possible de d_cbs ou de blessure grave si vous

ne suivez pas les instructions.

Tous les messages de s_curit_ vous diront quel est le danger potentiel et vous disent comment r_duire le risque de blessure et

ce qui peut se produire en cas de non-respect des instructions.

IMPORTANTES iNSTRUCTiONS DE SECURITE

AVERTISSEIVIENT : POUR REDUIRE LE RISQUE

D'INCENDIE, CHOC ¢:LECTRIQUE OU DOMMAGES

CORPORELS, RESPECTER LES INSTRUCTIONS

SUIVANTES :

m Utiliser cet appareil uniquement dans les applications

envisag6es par le fabricant. Pour toute question, contacter

le fabricant.

m Avant d'entreprendre un travail d'entretien ou de nettoyage,

interrompre I'alimentation de la hotte au niveau du tableau

de disjoncteurs, et verrouiller le tableau de disjoncteurs

pour emp6cher tout r@ablissement accidentel de

I'alimentation du circuit. Lorsqu'il n'est pas possible de

verrouiller le tableau de disjoncteurs, placer sur le tableau

de disjoncteurs une @iquette d'avertissement pro6minente

interdisant le r@ablissement de I'alimentation.

m Tout travail d'installation ou c&blage 61ectrique doit 6tre

r6alis6 par une personne qualifi6e, dans le respect des

prescriptions de tousles codes et normes applicables, y

compris les codes du b&timent et de protection contre les

incendies.

m Une source d'air de d6bit suffisant est n6cessaire pour le

fonctionnement correct de tout appareil & gaz (combustion

et 6vacuation des gaz & combustion par lachemin6e), pour

qu'il n'y ait pas de reflux des gaz de combustion. Respecter

les directives du fabricant de 1'6quipement de chauffage et

les prescriptions des normes de s6curit6 - comme celles

publi6es par la National Fire Protection Association (NFPA)

et I'American Society for Heating, Refrigeration and Air

Conditioning Engineers (ASHRAE), et les prescriptions des

autorit6s r6glementaires locales.

m Lors d'op@ations de d6coupage et de perqage dans un mur

ou un plafond, veiller & ne pas endommager les c&blages

61ectriques ou canalisations qui peuvent s'y trouver.

m Les ventilateurs d'6vacuation doivent toujours d6charger

I'air & I'ext@ieur.

IVilSE EN GARDE : Cet appareil est con_:u uniquement

pour la ventilation g6n@ale. Ne pas I'utiliser pour I'extraction

de mati_res ou vapeurs dangereuses ou explosives.

MISE EN GARDE : Pour minimiser le risque d'incendie

et 6vacuer ad6quatement les gaz, veiller &acheminer I'air

aspir6 par un conduit jusqu'& I'ext@ieur - ne pas d6charger

I'air aspir6 dans un espace vide du b&timent comme une

cavit6 murale, un plafond, un grenier, un vide sanitaire ou

un garage.

AVERTISSEMENT : POUR R¢:DUIRE LE RISQUE

D'INCENDIE, UTILISER UNIQUEMENT DES CONDUITS

MI2TALLIQUES.

AVERTISSEIVIENT : POUR MINIMISER LE RISQUE

D'UN FEU DE GRAISSE SUR LA CUISINIF:RE :

[] Ne jamais laisser un 616ment de surface fonctionner &

puissance de chauffage maximale sans surveillance. Un

renversement/d6bordement de mati@e graisseuse pourrait

provoquer une inflammation et la g6n@ation de fum6e.

Utiliser une puissance de chauffage moyenne ou basse

pour le chauffage d'huile.

[] Veiller &toujours faire fonctionner le ventilateur de la hotte

Iors de la cuisson avec une puissance de chauffage 61ev6e

ou Iors de la cuisson d'un mets &flamber (& savoir cr6pes

Suzette, cerise jubil6e, steak au poivre flamb6).

[] Nettoyer fr6quemment les ventilateurs d'extraction. Veiller &

ne pas laisser la graisse s'accumuler sur les surfaces du

ventilateur ou des filtres.

[] Utiliser toujours un ustensile de taille appropri6e. Utiliser

toujours un ustensile adapt6 & la taille de 1'616ment

chauffant.

AVERTISSEMENT : POUR RE_DUIRE LE RISQUE DE

DOMMAGES CORPORELS APRF:S LE DECLENCHEMENT

D'UN FEU DE GRAISSE SUR LA CUISINIt_RE, APPLIQUER

LES RECOMMANDATIONS SUIVANTES :a

[] Placer sur le r6cipient un couvercle bien ajust6, une t61e &

biscuits ou un plateau m6tallique POUR ETOUFFER LES

FLAMMES, puis 6teindre le brt_leur. VEILLER ,&.¢:VITER

LES BRULURES. Si les flammes ne s'@eignent pas

imm6diatement, ¢:VACUER LA PIECE ET APPELER LES

POMPIERS.

[] NE JAMAIS PRENDRE EN MAIN UN RECIPIENT

ENFLAMME - vous risquez de vous brQler.

[] NE PAS UTILISER D'EAU, ni un torchon humide - ceci

pourrait provoquer une explosion de vapeur brQlante.

[] Utiliser un extincteur SEULEMENT si:

- II s'agit d'un extincteur de classe ABC, dont on connaft le

fonctionnement.

- II s'agit d'un petit feu encore limit6 & I'endroit oQ il s'est

d6clar&

- Les pompiers ont 6t6 contact6s.

- II est possible de garder le dos orient6 vers une sortie

pendant I'op@ation de lutte contre le feu.

aRecommandations tir6es des conseils de s6curit6 en cas

d'incendie de cuisine publi6s par la NFPA.

[] AVERTISSEMENT : Pour r6duire le risque d'incendie

ou de choc 61ectrique, ne pas utiliser ce ventilateur avec un

quelconque dispositif de r6glage de la vitesse & semi-

conducteurs.

CONSERVEZ CES iNSTRUCTiONS

EXIGENCESD'INSTALLATION

(o}u csg®®

Rassembler les outils et pieces necessaires avant de commencer

I'installation. Lire et suivre les instructions fournies avec les outils

indiques ici.

Outillage n_cessaire

• Niveau

• Perceuse avec forets de 11¼"(3,0 cm), 3/8"(9,5 mm),

7A4"(2,75 mm) et 1/8"(3,0 mm)

• Crayon

• Pince a denuder ou couteau utilitaire

• Metre-ruban ou regle

• Pince

• Pistolet a calfeutrage et compose de calfeutrage resistant

aux intemperies

• Brides pour conduit d'evacuation

• Scie sauteuse ou scie a guichet

• Tournevis a lame plate

• Cisaille de ferblantier

• Tournevis Phillips

• Ensemble de cles Allen (systeme metrique)

Pi_ces n_cessaires

• C&ble d'alimentation electrique de la residence

• Deux serre-c&ble de 1/2"(12,7 mm) - homologation UL

ou CSA

• 3 connecteurs de fils homologues UL

Pour une installation avec d_charge a I'ext_rieur (recyclage) -

Materiel additionnel n_cessaire :

• 1 bouche de decharge (decharge a travers le mur ou _ travers

le toit)

• Conduit d'evacuation metallique

Pour une installation sans d_charge a I'ext_rieur (recyclage) -

Materiel additionnel n_cessaire :

• Ensemble de filtre a charbon (piece n° 4396848) - seulement

pour une installation sans decharge a I'exterieur (recyclage).

Voir la section "Assistance ou service" pour placer une

commande.

Pi_ces fournies

Retirer les pieces des emballages. Verifier que toutes les pieces

sont presentes.

• Hotte avec ventilateur et lampes installes

• Deflecteur pour installation sans decharge a I'exterieur

(recyclage)

• Raccord de transition avec clapet anti-reflux installe

• Filtre(s) - selon le modele et la dimension

• 2 crochets de montage

• Bride de support du cache-conduit

• Cache-conduit- 2 pieces

• Ruban de caoutchouc

• 2 vis de 2,9 x 6,5 mm

• 2 vis de 3,5 x 6,5 mm

• 2 vis de 3,5 x 9,5 mm

• 2 vis de 6,0 x 70,0 mm

• 6- Vis de montage de 5,0 x 35,0 mm

• 2 - Chevilles d'ancrage de 10,0 x 60,0 mm

• Cle Allen pour vis Torx_*

IMPORTANT • Observer les dispositions de tous les codes et

reglements en vigueur.

Confier I'installation de la hotte &un technicien qualifie. C'est

I'installateur qu'incombe la responsabilite de respecter les

distances de separation exigees, specifiees sur la plaque

signaletique de I'appareil. La plaque signaletique de I'appareil est

situee derriere le filtre de gauche, sur la paroi arriere de la hotte.

On doit toujours installer la hotte a distance des sources de

courant d'air (fenatres, portes et bouches de chauffage).

Respecter les dimensions indiquees pour les ouvertures

decouper dans les placards; ces dimensions tiennent compte

des valeurs minimales des degagements de separation.

On doit disposer d'une prise de courant electrique reliee a la

terre. Voir la section "Specifications electriques".

La hotte est configuree a I'usine pour la decharge a travers le toit

ou un mur.

Pour une installation sans decharge a I'exterieur (recyclage), voir

"Installation sans decharge a I'exterieur (recyclage)" a la section

"Preparation de I'emplacement". L'ensemble Filtre a charbon

(piece numero 4396848) est disponible chez votre marchand ou

chez un distributeur de pieces autorise.

On doit assurer I'etancheite au niveau de chaque ouverture

decoupee dans le plafond ou un mur traverse par I'equipement

de la hotte.

Installation dans une r_sidence mobile

L'installation de cette hotte doit satisfaire aux exigences de la

norme Manufactured Home Construction Safety Standards, Titre

24 CFR, partie 328 (anciennement Federal Standard for Mobile

Home Construction and Safety, Titre 24, HUD, partie 280);

Iorsque cette norme n'est pas applicable, I'installation doit

satisfaire aux criteres de la plus recente edition de la norme

Manufactured Home Installation 1982 (Manufactured Home

Sites, Communities and Setups) ANSI A225.1/NFPA 501A*, ou

des codes et reglements Iocaux.

• Gabarit de montage

1-®TORX est une marque d_posae de Acument Intellectual Properties, LLC.

Dimensions du produit

(44,9 cm) 35%?'

(90,0crn)

max.

51"

(129,6 crn)

max.

97/8"

cm)

30" (76,2 cm)

35%" (89,9 cm) 204/5''

Dimensions & respecter Iors de I'installation

61/2"

(16,5 cm).

\. \_q_......__ 2" (5,1 cm) rain.

_-_:_::X:Y:'-;X':_ :, g'' (22,9 cm) rain*

61/4,,(t6,9om_":: :::..

Placard

lateral

30" (76,2 cm) rain.

36" (91,4 cm) max.

entre la base

de la hotte et

la surface de

CUJSSOn

". 16"

o/'/ (40,6 cm)

rain.

p...

30" _

('/6,2 cm)

357/lo" (90,0 cm)

Axe central

et du conduit

d'_vacuation

Placard

lateral

*Pour une installation sans decharge a I'exterieur (recyclage)

• Le syst@me d'@vacuation doit d@charger I'air a I'ext@rieur,

except@ pour les installations sans d@charge a I'ext@rieur

(recyclage).

• Ne pas terminer le conduit d'@vacuation dans un grenier ou

dans un autre espace ferm&

• Ne pas utiliser une bouche de decharge murale de

4" (10,2 cm) normalement utilisee pour un equipement de

buanderie.

• Utiliser un conduit metallique uniquement. Un conduit en

metal rigide est recommand& Ne pas utiliser un conduit de

plastique ou en feuille metallique.

• La Iongueur du circuit d'evacuation et le nombre de coudes

doivent _tre reduits au minimum pour fournir la meilleure

performance.

Pour un fonctionnement efficace et silencieux •

• Utiliser autant que possible des sections droites et minimiser

le nombre de coudes.

• Ne pas utiliser plus de trois coudes a 90°.

• Veiller & ce qu'il y ait une section droite de conduit de

24" (61,0 cm) ou plus entre deux coudes, si on doit utiliser

plus de 1 raccord coud&

• Ne pas installer 2 coudes ensemble.

• Au niveau de chaque jointure du conduit de decharge,

assurer I'etancheite avec les brides de serrage pour conduit.

• Le systeme d'evacuation doit comporter un clapet. Si la

bouche de decharge murale ou par le toit comporte un

clapet, ne pas utiliser le clapet fourni avec la hotte de

cuisiniere.

• Autour de la bouche de decharge a I'exterieur, assurer

I'etancheite avec un produit de calfeutrage.

• La taille du conduit doit _tre uniforme.

Installations pour r_gions & climat froid

Dans le circuit d'evacuation, on devrait installer un clapet anti-

reflux additionnel pour minimiser le reflux d'air froid, ainsi qu'un

element d'isolation thermique pour minimiser le transfert de

chaleur par conduction vers I'exterieur. Le clapet anti-reflux doit

_tre place du c6te air froid par rapport & I'element d'isolation

thermique.

L'element d'isolation thermique doit _tre aussi proche que

possible de I'endroit oQ le systeme d'evacuation s'introduit dans

la partie chauffee de la maison.

Air d'appoint

Le code du b&timent local peut exiger I'emploi d'un systeme de

renouvellement de I'air/introduction d'air d'appoint Iors de

I'utilisation d'un systeme d'aspiration de debit superieur & une

valeur (pieds cubes par minute) specifiee. Le debit specifie en

pieds cubes par minute est variable d'une juridiction & une autre.

Consulter un professionnel des installations de chauffage

ventilation/climatisation au sujet des exigences specifiques

applicables dans lajuridiction locale.

M_thodes d'_vacuation

Cette hotte est configuree & I'usine pour la decharge de I'air

aspire &travers le toit ou &travers un mur.

Un circuit d'evacuation en conduit rond de 6" (15,2 cm) est

necessaire pour I'installation (non fourni). La hotte comporte une

ouverture de sortie de diam_tre 6" (15,2 cm).

REMARQUE : On deconseille I'emploi d'un conduit flexible. Un

conduit flexible peut causer une retro-pression et des

turbulences de I'air, ce qui reduit considerablement la

performance.

La sortie & I'exterieur du circuit d'evacuation peut se faire &

travers le toit ou &travers un mur. Pour la sortie &travers un mur,

on doit employer un raccord coude &90°.

D_charge par I'arri_re

Le raccord coude a 90 ° peut _tre installe immediatement au-

dessus de la hotte.

Installation sans d_charge & I'ext_rieur (recyclage)

S'il n'est pas possible d'evacuer les fumees et vapeurs de

cuisson & I'exterieur, on peut employer la version "Installation

sans decharge & I'exterieur (recyclage)" de la hotte dotee d'un

filtre 9.charbon actif et du deflecteur. Les vapeurs/fumees sont

alors recyclees 9.travers la grille superieure.

D_charge a D_charge a Installation sans

travers le toit travers le tour d_charge

I'ext_rieur

(recyclage)

A. Bouche de A. Bouche de A. D_flecteur

d_charge sur toit d_charge murale B. Conduit dia.

B. Conduit dia. B. Conduit dia. 6" (15,2 cm)

6" (15,2 cm) 6" (15,2 cm)

Calcul de la Iongueur effective du circuit d'_vacuation

Pour calculer la Iongueur effective du circuit d'evacuation

necessaire, additionner les Iongueurs equivalentes (pieds/metres)

de tousles composants utilises dans le systeme.

Composant Conduit de diam_tre

6" (15,2 cm)

coude 9.45° 2,5 pi

(0,8m)

coude 9.90° 5,0 pi

(1,5m)

La Iongueur equivalente maximum est de 35 pi (10,7 m).

Exemple de syst_me de d_charge

Bouche de

co.do 9o° a h.,go .,olo

Dans I'exemple suivant, la Iongueur theorique du circuit est

inferieure au maximum de 35 pi (10,7 m).

1 - bouche de = 0 pi (0 m)

decharge murale

section droite de = 8 pi (2,4 m)

8 pi (2,4 m)

Longueur du systeme = 13 pi (3,9 m)

Observer les dispositions de tousles codes et reglements en

vigueur.

L'installation electrique doit satisfaire les exigences de la plus

recente edition de la norme National Electrical Code, ANSl/NFPA

70, ou de la norme CSA C22.1-94, Code canadien de I'electricite,

partie 1 et C22.2 N° 0-M91 (derniere edition) et de tousles codes

et reglements en vigueur.

Si les codes le permettent et si on utilise un conducteur distinct

de liaison 9.la terre, il est recommande qu'un electricien qualifie

verifie la qualite de la liaison 9.la terre.

Pour obtenir un exemplaire de la norme des codes ci-dessus,

contacter :

National Fire Protection Association

One Batterymarch Park

Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

• L'appareil doit _tre alimente par un circuit de 120 V, CA

seulement, 60 Hz, 15 A, protege par fusible.

• Si le domicile est equipe d'un c&blage en aluminium, suivre

les instructions suivantes :

1. Connecter une section de c&ble en cuivre massif aux

conducteurs en queue de cochon.

2. Connecter le c&blage en aluminium 9.la section ajoutee

de c&blage en cuivre en utilisant des connecteurs et/ou

des outils specialement congus et homologues UL pour

fixer le cuivre 9.I'aluminium.

Appliquer la procedure recommandee par le fabricant des

connecteurs. La connexion aluminium/cuivre doit _tre

conforme aux codes Iocaux et aux pratiques de c&blage

acceptees par I'industrie.

Le calibre des conducteurs et les connexions doivent _tre

compatibles avec la demande de courant de I'appareil

specifiee sur la plaque signaletique. La plaque signaletique

de I'appareil est situee derriere le filtre, sur la paroi arriere de

la hotte.

Le calibre des conducteurs doit satisfaire les exigences de la

plus recente edition de la norme National Electrical Code,

ANSl/NFPA 70, ou de la norme CSA C22.1-94, Code

canadien de I'electricite, partie 1 et C22.2 N° 0-M91 (derniere

edition) et de tousles codes et reglements en vigueur.

INSTRUCTIONSD'INSTALLATION

• On recommande que lecircuit d'evacuation soit installe avant 7. Fixer le gabarit en place avec du ruban adhesif; aligner I'axe

de la hotte, central du gabarit et le bas du gabarit avec la ligne

correspondant au bas de la hotte, et avec I'axe central dej&

• trace sur lemur.

Avant d'executer les decoupages, verifier la disponibilite d'un

espace de passage suffisant dans le plafond ou lemur pour

le conduit d'evacuation.

Avant de selectionner la hotte &installer, mesurer la hauteur

libre sous plafond et la hauteur maximum disponible sous la

hotte.

1. Deconnecter la source de courant electrique.

2. Determiner la methode d'extraction & utiliser : decharge &

travers le mur ou le toit, ou recyclage.

3. Selectionner une surface plane pour I'assemblage de la

hotte. Placer un materiau de protection sur cette surface.

Risque du poids e×cessif

Utiliser deux ou plus de personnes pour d_placer et

installer la hotte de la cuisini_re.

Le non=respect de cette instruction peut causer

une blessure au dos ou d'autre blessure.

4. A I'aide de deux personnes ou plus, soulever la hotte de la

cuisiniere et la poser sur une surface de protection.

Installation des vis de montage de la hotte

5. Determiner et marquer la position de I'axe central sur le mur

oQ la hotte sera installee.

6. Choisir une hauteur de montage - minimum 30" (76,2 cm) et

maximum sugger6 36" (91,4 cm) - au-dessus de la cuisiniere

jusqu'au fond de la hotte et tracer une ligne de ref6rence sur

le mur.

REMARQUE : Pour une configuration d'installation avec

hauteur sous plafond reduite (installation avec ou sans

decharge & I'exterieur), la hotte peut _tre installee avec la

section superieure du cache-conduit.

A.Axe central

B. Emplacement du crochet de montage

C. Emplacements des organes de fixation

D. Ligne de r_f_rence - hauteur de montage

A I'aide du gabarit, marquer sur lemur le centre des 6 trous

des organes de fixation.

IMPORTANT :Toutes les vis doivent _tre vissees dans du

bois.

Enlever le gabarit.

9. Percer des avant-trous de %4" (2,75 mm) sur tousles

emplacements pour la pose des vis dans du bois.

10. Fixer 2 crochets de montage au mur aux emplacements

marqu6s sur le gabarit.

A. Crochets de montage

B. Axe central sur lemur

Installation de la bride de cache-conduit

Installation avec utilisation de t_lescope et des sections

sup_rieure et inf_rieure du cache-conduit

1. Positionner la bride de cache-conduit sur lemur a environ 1/8"

(3,0 mm) du plafond.

2. Faire des reperes aux emplacements des trous.

Percer des trous de 3/8"(9,5 mm) pour les chevilles et inserer

ces dernieres en affleurement avec lemur.

, A

o.. o___ ................... C

A. Chevilles d'ancrage de 10 x 60 mm

B.Axe central sur le muff

C. Bride de support du cache-conduit

D. Visde 6 x 70 mm

4. Fixer la bride de support du cache-conduit au mur.

Emplacement d'installation avec hauteur de plafond

r_duite

REMARQUE : Les sections superieure et inferieure du cache-

conduit permettent toutes les deux de realiser cette installation. II

convient neanmoins de remarquer que la section superieure du

cache-conduit est plus petite que la section inferieure. Le

degagement sera plus important si la section superieure est

montee sur la hotte de cuisiniere.

Installations sans d_charge a I'ext_rieur (recyclage) :

La hotte est installee au moyen de la section superieure du

cache-conduit (26" [66,0 cm]) et d'une piece de colmatage en

bois d'une epaisseur de %" (10,0 mm).

1. Le support du cache-conduit doit _tre installe & une distance

de %" (10,0 mm) du plafond pour que le cache-conduit

puisse glisser et s'engager dans la partie superieure de la

hotte.

2. L'espace restant au-dessus du cache-conduit peut _tre

comble au moyen d'un morceau de contreplaqu6 de

%" (10,0 mm) d'epaisseur decoup6 aux dimensions de la

section transversale interieure du cache-cheminee et ajuste

en fonction de la hauteur du plafond.

Installations avec d_charge a I'ext_rieur :

La hotte est installee au moyen de la section inferieure du cache-

conduit (163_'' [42,5 cm]) et d'une piece de colmatage en bois

d'une epaisseur de %" (10,0 mm).

1. Le support du cache-conduit doit _tre installe a une distance

de %" (10,0 mm) du plafond pour que le cache-conduit

puisse glisser et s'engager dans la partie superieure de la

hotte.

2. L'espace restant au-dessus du cache-conduit peut _tre

comble au moyen d'un morceau de contreplaqu6 de

%" (10,0 mm) d'epaisseur decoup6 aux dimensions de la

section transversale interieure du couvercle du cache-

cheminee et ajuste en fonction de la hauteur du plafond.

3. Decouper le ruban en caoutchouc auto-adhesif fourni avec la

hotte en quatre morceaux identiques. Fixer deux morceaux

du ruban adhesif de chaque c6te de la bride de support.

.................................g

A. Bride de cache-conduit

B. Ruban de caoutchouc

Installation avec circuit d'6vacuation

Installer le raccord de transition au sommet de la hotte (s'il a et6

enleve pour expedition), avec 2 vis de t61erie.

Installation sans d_charge _ I'ext_rieur (recyclage)

1. Installer le raccord de transition au sommet de la hotte (s'il a

et6 enleve pour expedition), avec 2 vis de t61erie.

2. Fixer la bride de fixation au plafond du cache-conduit sur le

deflecteur, avec les deux vis de 3,5 x 9,5 mm fournies.

A. Bride de cache-conduit

B. Vis de 3,5 x 9,5 mm

C. D_flecteur

3. Connecter le deflecteur au raccord de transition avec le

conduit rond de diametre 6" (15,2 cm).

Derni_res _tapes de la preparation

1. Determiner et effectuer toutes les decoupes necessaires

dans le mur pour le passage du circuit d'evacuation. Installer

le systeme d'evacuation avant la hotte. Voir la section

"Exigences concernant I'evacuation".

2. Determiner la hauteur appropriee pour le conduit de 1/2";

percer un trou de 11¼"(3,2 cm) & cet endroit.

3. Faire passer lec&blage dans le conduit de 1/2"- respecter les

prescriptions des codes en vigueur (Code national de

I'electricite, normes CSA ou codes/reglements Iocaux); il faut

que la Iongueur du conduit de 1/2"et des conducteurs soit

suffisante depuis le tableau de distribution (avec fusibles ou

disjoncteurs) pour realiser facilement le raccordement dans le

boitier de connexion de la hotte.

REMARQUE : Ne pas mettre le systeme sous tension avant

d'avoir completement termine I'installation.

4. Utiliser un compose de calfeutrage pour assurer I'etancheit6

au niveau de chaque ouverture.

La page charge ...

IKEA IHW6302VM0 Guide d'installation

Marque: IKEA

Modèle: IHW6302VM0

Catégorie: Hottes

Taper: Guide d'installation

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: IKEA IHW6302VM0 Installation guide

IKEA IHW6302VM0 Guide d'installation

Ce manuel convient également à

IKEA IHW6302VM0 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents