Wacker Neuson RD27-120 Manuel utilisateur

5000185459 05 0813

Operator’s Manual

Roller

RD 27-100

RD 27-120

Notice d’Emploi

Rouleau

EN/FR

5000185459

Copyright

notice

All rights, including copying and distribution rights, are reserved.

This publication may be photocopied by the original purchaser of the machine. Any

other type of reproduction is prohibited without express written permission from

Wacker Neuson Production Americas LLC.

Any type of reproduction or distribution not authorized by Wacker Neuson Production

Americas LLC represents an infringement of valid copyrights. Violators will be

prosecuted.

Trademarks

All trademarks referenced in this manual are the property of their respective owners.

Manufacturer

Wacker Neuson Production Americas LLC

N92W15000 Anthony Avenue

Menomonee Falls, WI 53051 U.S.A.

Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957

www.wackerneuson.com

Original

instructions

This Operator’s Manual presents the original instructions. The original language of this

Operator’s Manual is American English.

5000185435 05 0813

RD 27 Foreword

wc_tx000836gb.fm 3

Foreword

Machines

covered in

this manual

Machine

identification

A nameplate listing the model number, item number, revision number, and serial

number is attached to this machine. The location of the nameplate is shown above.

Serial number

(S/N)

For future reference, record the serial number in the space provided below. You will

need the serial number when requesting parts or service for this machine.

Machine

documentation

 Keep a copy of the Operator’s Manual with the machine at all times.

 Use the separate Parts Book supplied with the machine to order replacement

parts.

 Refer to the separate Repair Manual for detailed instructions on servicing and

repairing the machine.

 If you are missing any of these documents, please contact Wacker Neuson

Corporation to order a replacement or visit www.wackerneuson.com.

 When ordering parts or requesting service information, be prepared to provide

the machine model number, item number, revision number, and serial number.

Machine Item Number

RD 27-100 0620393

0620395

0620508

0620510

0620512

5200009322

RD 27-120 0620396

0620394

0620509

0620511

0620513

5200009323

wc_gr010238

Serial Number:

Foreword RD 27

4 wc_tx000836gb.fm

Expectations

for

information in

this manual

 This manual provides information and procedures to safely operate and main-

tain the above Wacker Neuson model(s). For your own safety and to reduce the

risk of injury, carefully read, understand, and observe all instructions described

in this manual.

 Wacker Neuson Corporation expressly reserves the right to make technical

modifications, even without notice, which improve the performance or safety

standards of its machines.

 The information contained in this manual is based on machines manufactured

up until the time of publication. Wacker Neuson Corporation reserves the right

to change any portion of this information without notice.

Copyright

notice

 All rights, especially copying and distribution rights, are reserved.

 This publication may be reproduced through photocopying by the original pur-

chaser of the machine. Any other type of reproduction is prohibited without

express written permission from Wacker Neuson Corporation.

 Any type of reproduction or distribution not authorized by Wacker Neuson Cor-

poration represents an infringement of valid copyrights, and violators will be

prosecuted.

CALIFORNIA

Proposition

65 Warning:

Engine exhaust, some of its constituents, and certain vehicle components, contain

or emit chemicals known to the State of California to cause cancer and birth

defects or other reproductive harm.

Laws

pertaining to

spark

arresters

NOTICE: State Health Safety Codes and Public Resources Codes specify that in

certain locations spark arresters be used on internal combustion engines that use

hydrocarbon fuels. A spark arrester is a device designed to prevent accidental dis-

charge of sparks or flames from the engine exhaust. Spark arresters are qualified

and rated by the United States Forest Service for this purpose. In order to comply

with local laws regarding spark arresters, consult the engine distributor or the local

Health and Safety Administrator.

Trademarks

All trademarks referenced in this manual are the property of their respective own-

ers.

Original Declaration of Conformity

2013-CE-RD27-CAT_en.fm

EC Declaration of Conformity

Manufacturer

Wacker Neuson Production Americas LLC, N92W15000 Anthony Avenue,

Menomonee Falls, Wisconsin 53051 USA

Product

Product category

Product function

Item number

Net installed power

Measured sound power level

Guaranteed sound power level

RD 27-100, RD 27-120

Dual drum, ride-on roller

To compact soil and asphalt

0620393, 0620508, 0620510, 0620512, 0620394,

0620509, 0620511, 0620513

24,4 kW

104 dB(A)

106 dB(A)

Conformity Assessment Procedure

According to ANNEX VI

Notified Body

Établissement Public à Caractère Industriel et Commercial, Laboratoires de Trappes,

29, avenue Roger Hennequin - 78197 Trappes Cedex

Directives and Standards

We hereby declare that this product meets and complies with the relevant regulations and

requirements of the following directives and standards:

2006/42/EC, 2000/14/EC, 2004/108/EC, EN 500-1, EN 500-4

Authorized Person for Technical Documents

Axel Häret, Wacker Neuson Produktion GmbH & Co. KG, Preußenstraße 41, 80809 München

Menomonee Falls, WI, USA, 04.06.13

William Lahner

Managing Director

Paul Sina

Manager, Product Engineering

Dan Domanski

Technical Director

Table of Contents RD 27

6 wc_bo5000185435_05toc.fm

Foreword 3

EC Declaration of Conformity 5

1 Safety Information 9

1.1 Signal Words Found in this Manual .......................................................9

1.2 Machine Description and Intended Use ..............................................10

1.3 Safety Guidelines for Operating the Machine ......................................11

1.4 Safety Guidelines while Using Internal Combustion Engines ..............13

1.5 Guidelines for Service Safety ..............................................................14

2 Labels 16

2.1 Label Locations ...................................................................................16

2.2 Label Meanings ...................................................................................17

3 Lifting and Transporting 23

3.1 Lifting the Machine ..............................................................................23

3.2 Tying Down/Transporting the Machine ................................................24

4 Operation 25

4.1 Preparing the Machine for First Use ....................................................25

4.2 Position of the Operator ......................................................................25

4.3 Operation & Maintenance Locations ...................................................26

4.4 Unlocking/Locking the Articulated Joint ...............................................28

4.5 Using the Roll Over Protection Structure (ROPS) ...............................29

4.6 Installing the Rotating Beacon .............................................................30

4.7 Using the Seat Belt ..............................................................................31

4.8 Adjusting the Seat ...............................................................................32

4.9 Adjusting the Steering Column ............................................................33

4.10 Positioning the Scraper Bars ...............................................................33

4.11 Using the Anti-Vandalism Protection Devices .....................................34

4.12 Using the Water Spray System ...........................................................35

4.13 Using the Forward/Reverse Lever .......................................................36

4.14 Backup Alarm ......................................................................................37

4.15 Using the Flow Divider (if equipped) ...................................................38

4.16 Using the Vibration System .................................................................39

4.17 Using the Parking Brakes ....................................................................40

4.18 Warning Lights ....................................................................................41

4.19 Using the Lights and Horn ...................................................................42

4.20 Machine Stability .................................................................................43

RD 27 Table of Contents

wc_bo5000185435_05toc.fm 7

4.21 Operating on Slopes ........................................................................... 44

4.22 Preliminary Checks ............................................................................ 45

4.23 Mounting and Dismounting the Machine ............................................ 45

4.24 Starting the Engine ............................................................................. 46

4.25 Stopping the Engine ........................................................................... 47

4.26 Understanding the Operator Present System .................................... 48

4.27 Emergency Shutdown Procedure ....................................................... 48

5 Maintenance 50

5.1 Periodic Maintenance Schedule ......................................................... 50

5.2 Major Component Locations .............................................................. 52

5.3 Major Components ............................................................................. 53

5.4 Safety-Related Spare Parts ................................................................ 54

5.5 Maintaining the Seat and Seat Belt .................................................... 59

5.6 Checking the Air Filter Indicator ......................................................... 60

5.7 Cleaning the Air Cleaner and Primary Air Filter Element ................... 61

5.8 Changing the Air Filter Elements ........................................................ 62

5.9 Testing the Backup Alarm .................................................................. 63

5.10 Checking the Engine Coolant Level ................................................... 64

5.11 Checking the Engine Oil ..................................................................... 65

5.12 Checking Hydraulic Oil Level ............................................................. 66

5.13 Checking the Neutral Switch .............................................................. 66

5.14 Adjusting the Scraper Bars ................................................................. 68

5.15 Inspecting the Seat Belt ..................................................................... 69

5.16 Cleaning the Water Spray Nozzles .................................................... 70

5.17 Cleaning the Water Spray System Filter ............................................ 71

5.18 Cleaning and Changing the Fuel Filter/Water Separator ................... 72

5.19 Priming the Fuel System .................................................................... 73

5.20 Draining Water and Sediment from the Fuel Tank ............................. 74

5.21 Cleaning the Water Tank Strainer ...................................................... 75

5.22

Adjusting Alternator Belt Tension ....................................................... 76

5.23 Lubricating the Articulated Steering Joint ........................................... 77

5.24 Lubricating the Steering Cylinder ....................................................... 78

5.25 Testing the Brake System .................................................................. 79

5.26 Changing the Engine Oil and Filter .................................................... 80

5.27 Cleaning the Fuel Tank Cap and Fuel Strainer .................................. 81

5.28 Changing the Hydraulic Oil Filter ........................................................ 82

5.29 Cleaning the Hydraulic Oil Cooler ...................................................... 83

5.30 Disconnecting/Connecting the Battery ............................................... 84

5.31 Adjusting the Forward/Reverse Lever ................................................ 85

5.32 Changing the Hydraulic Oil ................................................................. 86

Table of Contents RD 27

8 wc_bo5000185435_05toc.fm

5.33 Checking and Cleaning the Hydraulic Tank Breather .........................87

5.34 Cleaning the Hydraulic Oil Strainer .....................................................88

5.35 Cleaning the Radiator Filler Cap .........................................................89

5.36 Checking the Engine Water Pump ......................................................90

5.37 Changing the Cooling System Coolant ...............................................91

5.38 Replacing the Water Temperature Regulator ......................................93

5.39 Draining the Water Spray System .......................................................94

5.40 Towing the Machine ............................................................................95

5.41 Manually Releasing the Parking Brakes ..............................................97

5.42 Troubleshooting ...................................................................................98

6 Technical Data 100

6.1 Engine ...............................................................................................100

6.2 Roller .................................................................................................101

6.3 Lubrication .........................................................................................101

6.4 Sound Measurements .......................................................................102

6.5 Measurements of Operator Exposure to Vibration ............................102

6.6 Dimensions ........................................................................................103

7 AEM Safety Manual 105

8 Schematics 132

8.1 Electrical Schematic (1 of 3) .............................................................132

8.2 Electrical Schematic (2 of 3) .............................................................133

8.3 Electrical Schematic (3 of 3) .............................................................134

8.4 Hydraulic Schematic (with flow divider) .............................................135

8.5 Hydraulic Schematic (without flow divider) ........................................136

wc_si000247gb.fm

9

RD 27 Safety Information

1 Safety Information

1.1 Signal Words Found in this Manual

This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE

signal words which must be followed to reduce the possibility of personal injury,

damage to the equipment, or improper service.

NOTICE: Used without the safety alert symbol, NOTICE indicates a situation

which, if not avoided, could result in property damage.

Note: A Note contains additional information important to a procedure.

This is the safety alert symbol. It is used to alert you to potential personal hazards.

f Obey all safety messages that follow this symbol.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

f To avoid death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

f To avoid possible death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

f To avoid possible minor or moderate injury from this type of hazard, obey all

safety messages that follow this signal word.

wc_si000247gb.fm

10

Safety Information RD 27

1.2 Machine Description and Intended Use

This machine is a dual drum, ride-on roller. The Wacker Neuson Ride-On Roller

consists of an articulated frame onto which is mounted a gasoline or diesel engine,

a fuel tank, a hydraulic tank, a water tank, a hydrostatic drive system, two steel

drums containing internal eccentric weights, and an operator’s platform with a

ROPS (Roll Over Protective Structure). The engine powers the hydraulic systems

that provide machine movement and drum vibration. The vibrating drums smooth

and compact the work surface as the machine moves. Machine speed, direction,

and vibration are controlled by the operator from the operator’s seat on the

platform.

The machine is designed as a lightweight roller to be used in the compaction of

sublayers and finish layers of asphalt on roads, driveways, parking lots, and other

types of asphalt-covered surfaces.

This machine has been designed and built strictly for the intended use described

above. Using the machine for any other purpose could permanently damage the

machine or seriously injure the operator or other persons in the area. Machine

damage caused by misuse is not covered under warranty.

The following are some examples of misuse:

 Using the machine as a ladder, support, or work surface

 Using the machine to carry or transport passengers or equipment

 Using the machine to tow other machines

 Using the machine to spray liquids other than water (i.e., diesel fuel on asphalt)

 Operating the machine outside of factory specifications.

 Operating the machine in a manner inconsistent with all warnings found on the

machine and in the Operator’s Manual.

This machine has been designed and built in accordance with the latest global

safety standards. It has been carefully engineered to eliminate hazards as far as

practicable and to increase operator safety through protective guards and labeling.

However, some risks may remain even after protective measures have been taken.

They are called residual risks. On this machine, they may include exposure to:

 Heat, noise, exhaust, and carbon monoxide from the engine

 Burns from hot hydraulic fluid

 Fire hazards from improper refueling techniques

 Fuel and its fumes

 Personal injury from improper lifting techniques

 Crushing hazards from improper operation (feet, legs, or arms extending

outside of the operator work station) and for other persons in the work zone

 Line of sight blockage by the ROPS

To protect yourself and others, make sure you thoroughly read and understand the

safety information presented in this manual before operating the machine.

wc_si000247gb.fm

11

RD 27 Safety Information

1.3 Safety Guidelines for Operating the Machine

Operator

qualifications

Only trained personnel are permitted to start, operate, and shut down the machine.

They also must meet the following qualifications:

 have received instruction on how to properly use the machine

 are familiar with required safety devices

The machine must not be accessed or operated by:

 children

 people impaired by alcohol or drugs

Personal

Protective

Equipment

(PPE)

Wear the following Personal Protective Equipment (PPE) while operating this

machine:

 Close-fitting work clothes that do not hinder movement

 Safety glasses with side shields

 Hearing protection

 Safety-toed footwear

Operator

training

Before operating the machine:

 Read and understand the operating instructions contained in all manuals

delivered with the machine.

 Familiarize yourself with the location and proper use of all controls and safety

devices.

 Contact Wacker Neuson for additional training if necessary.

When operating this machine:

 Do not allow improperly trained people to operate the machine. People

operating the machine must be familiar with the potential risks and hazards

associated with it.

Machine’s

safety devices

 Disengage and stow the locking bar for the articulated steering joint before

operating the machine. The machine cannot be steered when the locking bar is

engaged.

 Check that all controls are functioning properly immediately after start-up!

To ensure safe operation of the machine:

 Do not operate the machine if any safety devices or guards are missing or

inoperative.

 Do not operate the machine unless all controls operate correctly.

 Do not modify or defeat safety devices.

 Do not use accessories or attachments that are not recommended by Wacker

Neuson. Damage to equipment and injury to the user or others may result.

wc_si000247gb.fm

12

Safety Information RD 27

Safe

operating

practices

When operating this machine:

 Always remain seated and wear the seat belt at all times while operating the

machine.

 Remain aware of changing positions and the movement of other equipment and

personnel on the job site.

 Be sure that all other persons are at a safe distance from the machine. Stop the

machine if people step into the working area of the machine.

 Remain aware of changing surface conditions, for example, uneven ground,

hills, trench edges, soft or coarse material. Be sure that the surface is stable

enough to support the weight of the machine and that there is no chance of the

machine sliding, falling, or tipping.

 Remain aware of the machine’s moving parts. Keep hands, feet, and loose

clothing away from the machine’s moving parts.

 Wear protective clothing appropriate to the job site when operating the machine.

 Wear safety glasses when operating this machine.

 Store the machine properly when it is not being used. The machine should be

stored in a clean, dry location out of the reach of children.

When operating this machine:

 Do not drive off curbs or other uneven surfaces that will result in jarring impacts

to the machine and operator.

 Do not touch the engine or muffler while the engine is on or immediately after it

has been turned off. These areas get hot and may cause burns.

 Do not allow anyone to ride on any part of the machine. Passengers can be

seriously injured or killed from falls, tip-overs, or roll-over incidents.

 Do not leave the machine running unattended.

 Do not operate a machine in need of repair.

 Do not attempt to start the machine while standing alongside it. Only start the

engine when seated in the driver’s seat and with the forward/reverse control in

the neutral position.

 Do not operate a machine when its fuel cap is loose or missing.

 Do not use a cellphone or send text messages while operating this machine.

 Do not operate the machine with unapproved accessories or attachments.

 Do not transport the machine while it is running.

wc_si000247gb.fm

13

RD 27 Safety Information

1.4 Safety Guidelines while Using Internal Combustion Engines

Operating

safety

When running the engine:

 Keep the area around exhaust pipe free of flammable materials.

 Check the fuel lines and the fuel tank for leaks and cracks before starting the

engine. Do not run the machine if fuel leaks are present or the fuel lines are

loose.

When running the engine:

 Do not smoke while operating the machine.

 Do not run the engine near sparks or open flames.

 Do not touch the engine or muffler while the engine is running or immediately

after it has been turned off.

 Do not operate a machine when its fuel cap is loose or missing.

 Do not start the engine if fuel has spilled or a fuel odor is present. Move the

machine away from the spill and wipe the machine dry before starting.

Refueling

safety

When refueling the engine:

 Clean up any spilled fuel immediately.

 Refill the fuel tank in a well-ventilated area.

 Reinstall the fuel tank cap after refueling.

 Do not smoke.

 Do not refuel a hot or running engine.

 Do not refuel the engine near sparks or open flames.

 Use suitable tools for refueling (for example, a fuel hose or funnel).

 Do not refuel if the machine is positioned in a truck fitted with a plastic bed liner.

Static electricity can ignite the fuel or fuel vapors.

WARNING

Internal combustion engines present special hazards during operation and fueling.

Failure to follow the warnings and safety standards could result in severe injury or

death.

f Read and follow the warning instructions in the engine owner’s manual and the

safety guidelines below.

DANGER

Exhaust gas from the engine contains carbon monoxide, a deadly poison.

Exposure to carbon monoxide can kill you in minutes.

f NEVER operate the machine inside an enclosed area, such as a tunnel, unless

adequate ventilation is provided through such items as exhaust fans or hoses.

wc_si000247gb.fm

14

Safety Information RD 27

1.5 Guidelines for Service Safety

Personal

Protective

Equipment

(PPE)

Wear the following Personal Protective Equipment (PPE) while servicing or maintaining

this machine:



Close-fitting work clothes that do not hinder movement



Safety glasses with side shields



Hearing protection



Safety-toed footwear

In addition, before servicing or maintaining the machine:



Tie back long hair.



Remove all jewelry (including rings).

Precautions



To reduce the risk of personal injury, read and understand the service procedures

before performing any service to the machine.



Some service procedures require that the machine’s battery be disconnected.



All adjustments and repairs MUST be completed before operation. NEVER operate

the machine with a known problem or deficiency! All repairs and adjustments should

be completed by a qualified technician.



Stop the engine before servicing the machine. If the engine has electric start,

disconnect the negative terminal on the battery.



Secure the articulated steering joint using the locking bar before lifting, jacking, and

servicing the machine. Machine halves could swing together unexpectedly and

cause a serious injury.

Accessories,

safety

devices, and

modifications



Do not modify, weld, or drill safety frames (ROPS) fitted as original equipment.



Do not loosen or remove bolts.



Do not weld, drill, or modify a broken safety frame.



Do not modify the machine without the express written approval of the manufacturer.

Replacing

parts and

labels



Replace worn or damaged components.



When replacement parts are required for this machine, use only Wacker Neuson

replacement parts or those parts equivalent to the original in all types of

specifications, such as physical dimensions, type, strength, and material.



Never use or attempt to repair a damaged safety belt or ROPS. Replace these

components before operating the machine.



Replace all missing and hard-to-read labels. Labels provide important operating

instructions and warn of dangers and hazards.



Check all external fasteners at regular intervals.

WARNING

A poorly maintained ained machine can become a safety hazard! In order for the

machine to operate safely and properly over a long period of time, periodic

maintenance and occasional repairs are necessary.

f ALWAYS do periodic maintenance as recommended in the Operator’s Manual.

wc_si000247gb.fm

15

RD 27 Safety Information

Lifting and

transporting

When lifting the machine:



Make sure slings, chains, hooks, ramps, jacks and other types of lifting devices are

attached securely and have enough weight-bearing capacity to lift or hold the

machine safely.



Remain aware of the location of other people when lifting the machine.

To reduce the possibility of injury:



Do not stand under the machine while it is being hoisted or moved.



Do not get onto the machine while it is being hoisted or moved.

Cleaning and

servicing the

machine

While cleaning or servicing the machine:



Keep the area around the muffler free of debris such as leaves, paper, cartons, etc.

A hot muffler could ignite the debris and start a fire.



Keep the machine clean and labels legible.



Keep hands, feet, and loose clothing away from moving parts.

While cleaning or servicing the machine:



Do not remove air cleaner cover, paper element, or precleaner while engine is

running.



Do not attempt to open the radiator cap while the machine is running or before the

engine has cooled down. Severe burns may result!



Do not attempt to clean or service the machine while it is running. Rotating parts can

cause severe injury.



Do not use gasoline or other types of fuels or flammable solvents to clean parts,

especially in enclosed areas. Fumes from fuels and solvents can become explosive.



Do not tip the machine for cleaning or for any other reason.



Always replace safety devices and guards after completing repairs and

maintenance.



Before you start the machine, ensure that all tools have been removed from the

machine and that replacement parts and adjusters are firmly tightened.

WARNING

Possibility of injury. Hydraulic fluid under pressure can penetrate the skin, cause

burns, blind, or create other potentially dangerous hazards.

f Set all controls to neutral, turn the engine off, and allow fluids to cool before

loosening hydraulic fittings or attaching test gauges.

f Do not open hydraulic lines or loosen hydraulic connections when the engine is

running.

f Before dismantling hydraulic connectors or hoses, ensure that all pressure has

been bled from the circuit.

f Fluid leaks from small holes are often practically invisible. DO NOT use your

bare hands to check for leaks. Check for leaks using a piece of cardboard or

wood.

f Always make sure hose connections have been reconnected back to the

correct fitting. Failure to do so may result in damage to the machine and/or

injury to person on or near the machine.

Labels RD 27

16 wc_si000393gb.fm

2 Labels

2.1 Label Locations

a

k

p

s

n

v

x

n

v

t

f

b

bb

d

g

r

d

g

f

g

q

i

o

d

f

w

z

c

k

b

u

h

aa

l

m

j

wc_gr005053

RD 27 Labels

wc_si000393gb.fm 17

2.2 Label Meanings

a Operator’s Manual must be stored on

machine. Replacement Operator’s Manual

can be ordered through your local Wacker

Neuson distributor.

b DANGER!

Read and understand the supplied

Operator's Manuals before operating this

machine. Failure to do so increases the risk

of injury to yourself and others.

Do not run the machine indoors or in an

enclosed area without adequate ventilation.

Engine exhaust contains carbon monoxide.

This is a poison you cannot see or smell.

Exposure to carbon monoxide can cause

loss of consciousness and CAN KILL YOU

IN MINUTES.

To reduce the risk of hearing loss, wear

hearing protection when operating this

machine.

Always wear seat belt when operating the

machine.

Never operate the machine sideways on

slopes.

E L M A N U A L D E O P E R A C I O N D E B E

S E R R E T E N I D O E N L A M A Q U I N A .

C O N T A C T E A S U D I S T R I B U I D O R

W A C K E R M A S C E R C A N O P A R A

P E D I R U N E J E M P L A R

A D I C I O N A L .

L A N O T I C E D ' E M P L O I D O I T

E T R E M U N I E S U R L A M A C H I N E .

C O N T A C T E R L E D I S T R I B U T E U R

W A C K E R L E P L U S P R O C H E

P O U R C O M M A N D E R U N

E X E M P L A I R E S U P P L E M E N T A I R E .

1 1 5 0 9 6

O P E R A T O R ' S M A N U A L M U S T B E

S T O R E D O N M A C H I N E .

R E P L A C E M E N T O P E R A T O R ' S

M A N U A L C A N B E O R D E R E D

T H R O U G H Y O U R L O C A L W A C K E R

D I S T R I B U T O R .

D I E B E T R I E B S V O R S C H R I F T M U S S

A N D E R M A S C H I N E A U F B E W A H R T

W E R D E N . Z U R B E S T E L L U N G V O N

E R S A T Z B Ü C H E R N W E N D E N S I E

S I C H B I T T E A N I H R E N

Ö R T L I C H E N W A C K E R H Ä N D L E R .

Labels RD 27

18 wc_si000393gb.fm

cDANGER

Asphyxiation hazard. Do not run the machine

indoors or in an enclosed area without ade-

quate ventilation. Read the Operator’s Man-

ual for instructions. No sparks, flames, or

burning objects near machine. Stop the

engine before adding fuel. Use only diesel

fuel.

dNOTICE

Lifting point

fWARNING

Avoid crushing area.

g Tie-down point

hWARNING

Disconnect battery before servicing.

Read Repair Manual.

Explosion hazard. Batteries can emit explo-

sive hydrogen gas. Keep all sparks and

flames away from the battery.

0178715

STOP

178709

RD 27 Labels

wc_si000393gb.fm 19

i Hydraulic oil drain

j Hydraulic oil reservoir fill.

k Water tank fill

l WARNING

Pinching hazard. Rotating machinery.

m WARNING

Pressurized contents. Do not open when hot!

HYDRAULIC OIL

HYDRAULIKÖL

ACEITE HIDRÁULICO

HUILE HYDRAULIQUE

Labels RD 27

20 wc_si000393gb.fm

nWARNING

Avoid crushing area.

o Engine oil drain

p Key switch positions.

Power to glowplugs.

Engine stopped (OFF).

Engine ON.

Power to starter motor.

q Throttle lever positions.

High speed.

Low speed.

r Vibration activation and deactivation switch.

Forward/reverse lever positions.

ENGINE OIL

MOTOROEL

ACEITE DE MOTOR

HUILE À MOTEURS

STOP

La page charge ...

Wacker Neuson RD27-120 Manuel utilisateur

Ce manuel convient également à

Wacker Neuson RD27-120 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents