HMS Anybus Wireless Bridge II Startup Manual

Marque: HMS

Modèle: Anybus Wireless Bridge II

Taper: Startup Manual

Anybus

®Wireless Bridge II™

STARTUP GUIDE

SCM-1202-013/SP2167 EN 1.9 ENGLISH

Important User Information

Liability

Every care has been taken in the preparation of this document. Please inform HMS Industrial Networks AB

of any inaccuracies or omissions. The data and illustrations found in this document are not binding. We,

HMS Industrial Networks AB, reserve the right to modify our products in line with our policy of continuous

product development. The information in this document is subject to change without notice and should not

be considered as a commitment by HMS Industrial Networks AB. HMS Industrial Networks AB assumes no

responsibility for any errors that may appear in this document.

There are many applications of this product. Those responsible for the use of this device must ensure that

all the necessary steps have been taken to verify that the applications meet all performance and safety

requirements including any applicable laws, regulations, codes, and standards.

HMS Industrial Networks AB will under no circumstances assume liability or responsibility for any problems

that may arise as a result from the use of undocumented features, timing, or functional side effects found

outside the documented scope of this product. The effects caused by any direct or indirect use of such

aspects of the product are undefined, and may include e.g. compatibility issues and stability issues.

The examples and illustrations in this document are included solely for illustrative purposes. Because of the

many variables and requirements associated with any particular implementation, HMS Industrial Networks

AB cannot assume responsibility for actual use based on these examples and illustrations.

Intellectual Property Rights

HMS Industrial Networks AB has intellectual property rights relating to technology embodied in the product

described in this document. These intellectual property rights may include patents and pending patent

applications in the USA and other countries.

Anybus®is a registered trademark and Wireless Bridge II™is a trademark of HMS Industrial Networks AB.

All other trademarks mentioned in this document are the property of their respective holders.

Anybus®Wireless Bridge II™Startup Guide SCM-1202-013/SP2167 EN 1.9

Preparation 3 (16)

1 Preparation

1.1 About This Document

This document describes how to install Anybus Wireless Bridge II and set up a

basic configuration.

For additional documentation, configuration examples, FAQs, troubleshooting

guides and technical support, please visit www.anybus.com/support.

1.2 Document Conventions

The following formatting conventions are used in this document to indicate safety

information and other content of specific importance:

WARNING

This instruction must be followed to avoid a risk of death or serious injury.

Caution

This instruction must be followed to avoid a risk of personal injury.

This instruction must be followed to avoid a risk of reduced functionality

and/or damage to the equipment, or to avoid a network security risk.

This is additional information which may facilitate installation and/or

operation.

Anybus®Wireless Bridge II™Startup Guide SCM-1202-013/SP2167 EN 1.9

Preparation 4 (16)

1.3 Product Description

Anybus Wireless Bridge II provides wireless communication over WLAN and/or

Bluetooth®to wired networks.

Typical applications for Anybus Wireless Bridge II include:

• Adding wireless cloud connectivity to industrial devices

• Accessing devices from a laptop, smartphone or tablet

• Ethernet cable replacement between devices

Note:

Bluetooth PAN (Personal Area Network) may not work with some devices due to

different implementations of Bluetooth by different manufacturers.

WLAN 5 GHz cannot be used at the same time as WLAN 2.4 GHz or Bluetooth.

1.4 Model Name – Certification Identifier

The model name consists of a model prefix followed by two designators for

interface configuration and functionality.

Prefix AWB3 Anybus Wireless Bridge II

Interface configuration A

Internal antenna, Dual M12

External antenna, Dual M12, RP-SMA

Functionality A

Ethernet with digital input

Ethernet w/o digital input

Example: AWB3AA = Anybus Wireless Bridge II with internal antenna, Ethernet

networking and digital input.

Anybus®Wireless Bridge II™Startup Guide SCM-1202-013/SP2167 EN 1.9

Installation 5 (16)

2 Installation

2.1 Safety

Caution

This equipment emits RF energy in the ISM (Industrial, Scientific, Medical)

band. Make sure that all medical devices used in proximity to this device

meet appropriate susceptibility specifications for this type of RF energy.

Caution

The M12 power and LAN connectors must be provided with tool operated

mechanical lock nuts that are tightened by the installer.

This product is recommended for use in both industrial and domestic

environments. For industrial environments it is mandatory to use the

functional earth connection to comply with immunity requirements. For

domestic environments the functional earth must be used if a shielded

Ethernet cable is used, in order to meet emission requirements.

This product contains parts that can be damaged by electrostatic

discharge (ESD). Use ESD prevention measures to avoid damage.

2.2 General Information

Make sure that you have all the necessary information about the capabilities and

restrictions of your local network environment before installation.

For optimal reception, wireless devices require a zone between them clear of

objects that could otherwise obstruct or reflect the signal. A minimum distance of

50 cm between the devices should also be observed to avoid interference.

For models with internal antenna the characteristics of the antenna should be

considered when choosing the placement and orientation of the unit.

See the Anybus Wireless Bridge II User Manual for more information.

Anybus®Wireless Bridge II™Startup Guide SCM-1202-013/SP2167 EN 1.9

Installation 6 (16)

2.3 Mechanical Installation

Anybus Wireless Bridge II can be screw-mounted directly onto a flat surface or

mounted on a standard DIN rail using the optional DIN mounting kit.

All measurements are in mm.

Anybus®Wireless Bridge II™Startup Guide SCM-1202-013/SP2167 EN 1.9

Installation 7 (16)

2.4 Connectors

Power Connector (A-coded male M12)

Pin Function

1 Power + (9–30 V)

2 Digital Input Ground

3 Power Ground

4 Digital Input + (9–30 V)

5 Functional Earth

The digital input can be used for additional functionality with advanced

configurations and to reset the unit. For more information please refer to the

Anybus Wireless Bolt/Bridge II AT Reference Guide.

If voltage is applied to the digital input for more that 10 seconds the unit

will be reset to factory defaults.

Signal wiring for the digital input must be carried in the same cable as

power and functional earth if wiring length exceeds 3 meters.

LAN Connector (D-coded female M12)

Pin Function Color coding (T568B)

1 Transmit + Orange/White

2 Receive + Green/White

3 Transmit - Orange

4 Receive - Green

Anybus®Wireless Bridge II™Startup Guide SCM-1202-013/SP2167 EN 1.9

Installation 8 (16)

2.5 LED Indicators

Status Indicators

LED Indication Description

PWR Off No power

Green Normal operation

WLAN

Off WLAN disabled or no power

Blue, blinking Access Point: No clients, awaiting connections

Blue Access Point: Connected to at least one client

Client: Connected to access point

Blue, flickering WLAN data activity (when connected)

Purple, blinking Client: Scanning for access points

Purple Client: Connecting to a detected access point

Red Unrecoverable error

LAN

Off No Ethernet connection

Yellow Ethernet link present

Yellow, flickering Ethernet data activity (when connected)

Off Bluetooth disabled or no power

Blue, blinking NAP: No clients, awaiting connections

Blue NAP: Connected to at least one PANU client

PANU: Connected to NAP

Blue, flickering Bluetooth data activity (when connected)

Purple PANU: Trying to connect to NAP

Red Unrecoverable error

Anybus®Wireless Bridge II™Startup Guide SCM-1202-013/SP2167 EN 1.9

Installation 9 (16)

Link Quality/Mode Indicators

RSSI (WLAN Client) / Link Quality (Bluetooth PANU)

LED Description

No connection

A RSSI/Link Quality < 25 %

A B RSSI/Link Quality 25–50 %

A B C RSSI/Link Quality 50–75 %

A B C D RSSI/Link Quality > 75 %

These LEDs are also used when selecting an Easy Config mode and to indicate

update status in Recovery Mode.

See Easy Config, p. 11 and Recovery Mode LED Indications, p. 10.

Anybus®Wireless Bridge II™Startup Guide SCM-1202-013/SP2167 EN 1.9

Installation 10 (16)

2.6 MODE Button

The MODE button can be used to restart or reset the unit as well as for selecting

an Easy Config mode.

When the unit is powered on, press and hold MODE for >10 seconds and then

release it to reset to the factory default settings.

Recovery Mode

If the web interface cannot be accessed, the unit can be reset by starting in

Recovery Mode and reinstalling the firmware using Anybus Firmware Manager

II, which can be downloaded from www.anybus.com/support.

To enter Recovery Mode, press and hold RESET during startup.

Firmware updates should normally be carried out through the web

interface. Recovery Mode should only be used if the unit is unresponsive

and the web interface cannot be accessed.

Recovery Mode LED Indications

In Recovery Mode the Status LEDs will indicate firmware update status:

PWR Green Firmware update in progress

Green, blinking Waiting for valid firmware

WLAN +BT Alternating red/blue Firmware update in progress

Anybus®Wireless Bridge II™Startup Guide SCM-1202-013/SP2167 EN 1.9

Configuration 11 (16)

3 Configuration

Anybus Wireless Bridge II is normally configured via the web interface or using

one of the pre-configured Easy Config modes.

Advanced configuration can be carried out by issuing AT commands via the web

interface or over a Telnet or RAW TCP connection to port 8080.

3.1 Web Interface

The web interface is accessed by pointing a web browser to the IP address of

the unit. The default address is 192.168.0.99.

The configuration settings are described in detail in the User Manual.

3.2 Easy Config

1. Power on the unit and wait for the Link Quality LEDs to light up and go out

again, then immediately press and release the MODE button.

2. Press MODE repeatedly to cycle through the Easy Config modes until the

desired mode is indicated by the A-B-C-D LEDs.

3. Within 20 seconds of step 2, press and hold MODE for 2 seconds. When the

button is released the unit will restart in the selected mode.

Anybus®Wireless Bridge II™Startup Guide SCM-1202-013/SP2167 EN 1.9

Configuration 12 (16)

3.2.1 Easy Config Modes

EC LED Role Description

1A Bluetooth PANU Configure as a client and scan for another

client (PANU to PANU).

2B–Reset configuration to factory defaults.

3A B –Reset IP settings to factory defaults.

4CClient Wait for automatic configuration.

5A C WLAN AP Configure units in mode 4 as clients.

Restart as access point and connect clients.

6B C Bluetooth NAP

7A B C WLAN AP Configure units in mode 4 as clients.

Restart as access point and connect clients.

Apply PROFINET optimization to all units.

8D Bluetooth NAP

9A D Bluetooth PANU

Configure as a client and scan for another

client (PANU to PANU).

Apply PROFINET optimization to both units.

10 B D (any) Apply PROFINET optimization and restart.

11 A B D (any) Enable PROFIsafe mode.

The Easy Config modes are also described in detail when selected in the web

interface.

Anybus

®Wireless Bridge II™Startup Guide SCM-1202-013/SP2167 EN 1.9

Configuration 13 (16)

3.3 Factory Restore

Any one of these actions will restore the factory default settings:

• Clicking on Factory Restore on the System Settings page

• Executing Easy Config Mode 2

• Issuing the AT command AT&F and then restarting the unit

• Holding MODE pressed for >10 seconds and then releasing it

• Applying voltage to the digital input for >10 seconds

Default Network Settings

IP Assignment Static

IP Address 192.168.0.99

Subnet Mask 255.255.255.0

Default Gateway 192.168.0.99

Internal DHCP Server Disabled

Default WLAN Settings

Operating Mode Client

Channel Bands 2.4 GHz & 5 GHz

Authentication Mode WPA/WPA2–PSK

Channel Auto

Bridge Mode Layer 3 IP forward

MIMO AWB3000: Disabled

AWB3010: Enabled (Disabled before FW version 1.6.3)

Default Bluetooth Settings

Operating Mode PANU (Client)

Local Name [generated from MAC address]

Connectable No

Discoverable No

Security Mode Just works

Bluetooth LE Disabled

Anybus®Wireless Bridge II™Startup Guide SCM-1202-013/SP2167 EN 1.9

Configuration 14 (16)

3.4 Configuration Examples

More examples can be found at www.anybus.com/support.

3.4.1 Ethernet Bridge via WLAN or Bluetooth®

Configuration with Easy Config

This example describes how to connect two Ethernet network segments via

WLAN or Bluetooth using Easy Config.

Configuration

1. Power on the first unit and wait for the LEDs to light up and go out, then

press MODE and release it immediately.

2. Press MODE repeatedly until only LED Cis lit (Easy Config Mode 4), then

confirm by pressing and holding MODE for 2 seconds.

This unit will now be discoverable and open for automatic configuration.

3. Power on the second unit and wait for the LEDs to light up and go out, then

press MODE and release it immediately..

4. Press MODE repeatedly on the second unit until A+Care lit (Mode 5) for

WLAN, or B+C(Mode 6) for Bluetooth, then confirm by pressing and

holding MODE for 2 seconds.

This unit should now automatically discover and configure unit 1 as a WLAN

or Bluetooth client, and configure itself as an access point.

Unit 1 will automatically be assigned the first free IP address within the

same Ethernet subnet as unit 2.

Adding More Devices

Up to 6 additional clients can be added by repeating the procedure. Each new

client will be assigned the next free IP address within the current subnet.

Anybus®Wireless Bridge II™Startup Guide SCM-1202-013/SP2167 EN 1.9

Technical Data 15 (16)

4 Technical Data

4.1 Hardware Specifications

Order code AWB3000 AWB3010

Wired Interface type Ethernet

Antenna 3 internal antennas:

2.4 GHz

2.4 GHz MIMO

5 GHz

1 external antenna:

2.4 GHz + 5 GHz dual band

Maximum range 400 m (WLAN and Bluetooth)

Dimensions (LxWxH) 93 x 68 x 33.2 mm

Weight 120 g

Operating temperature -40 to +65 °C

Storage temperature -40 to +85 °C

Humidity EN 600068-2-78: Damp heat, +40 °C, 93 % humidity for 4 days

Vibration See datasheet

Pressure 850 to 1050 mB

Housing material Plastic (see data sheet for details)

Protection class IPX5

Mounting Screw mount or DIN rail using optional clip

Power connector M12 male A-coded

Ethernet connector M12 female D-coded

Power supply 9–30 VDC (-5 % +20 %)

Cranking 12 V (ISO 7637-2:2011 pulse 4)

Reverse polarity protection

Power consumption 0.7 W (idle), 1.7 W (max)

Anybus®Wireless Bridge II™Startup Guide SCM-1202-013/SP2167 EN 1.9

This page intentionally left blank

Anybus®Wireless Bridge II™

Additional certification and compliance information

COMPLIANCE SHEET

This document does not include the complete instructions for the safe use of the described equipment.

Make sure that you have read and understood the safety instructions in the user documentation for the

described equipment before proceeding.

EMC Compliance (CE)

This product is in compliance with the Radio Equipment Directive 2014/53/EU through

conformance with the following standards. The Declaration of Conformity can be found

at www.anybus.com/support.

Effective use of

frequency spectrum

EMC Safety

EN 300 328 V2.1.1

EN 301 893 V2.1.1

EN 300 440 V2.1.1

EN 61000-6-2:2005

EN 61000-6-3:2007 + A1:2011

EN 301 489-1 V2.1.1

EN 301 489-17 V3.1.1

EN 60950-1:2006 + A11:2009 + A1:2010

+ A12:2011 + A2:2013

EN 62311:2008 (Wi-Fi)

EN 62479:2010 (Bluetooth)

Disposal and recycling

You must dispose of this product properly according to local laws and regulations.

Because this product contains electronic components, it must be disposed of

separately from household waste. When this product reaches its end of life, contact

local authorities to learn about disposal and recycling options, or simply drop it off at

your local HMS office or return it to HMS. For more information, see

www.hms-networks.com.

FCC Compliance Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This

equipment should be installed and operated with a minimum distance of 20 cm between the radiator and

your body.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and

2. this device must accept any interference received, including interference that may cause undesired

operation.

This product contains FCC ID: PVH0965

Any changes or modifications not explicitly approved by HMS Industrial

Networks AB could cause the module to cease to comply with FCC rules part

15, and thus void the user's authority to operate the equipment.

Industry Canada Statement

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with a minimum distance of 20 cm between

the radiator and your body.

Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and

2. this device must accept any interference received, including interference that may cause undesired

operation of the device.

Cet équipement est conforme aux limites d'exposition de rayonnement d'IC RSS-102 déterminées pour un

environnement non contrôlé. Cet équipement devrait être installé et actionné avec la distance minimum 20

cm entre le radiateur et votre corps.

Son utilisation est soumise aux deux conditions suivantes:

1. Cet appareil ne doit pas causer d’interférences et

2. il doit accepter toutes interférences reçues, y compris celles susceptibles d’avoir des effets

indésirables sur son fonctionnement.

This product contains IC ID: 5325A-0965

Anybus®Wireless Bridge II™Compliance Sheet 2 (3)

Other Certifications

Contains MIC ID: R 204-510009 (indoor use only)

IFETEL

Marca: Anybus

Modelo: AWB3

NOM-208-SCF1-2016

La operación de este equipo está sujeta a las

siguientes dos condiciones:

(1) es posible que este equipo o dispositivo no cause

interferencia perjudicial y

(2) este equipo o dispositivo debe aceptar cualquier

interferencia, incluyendo la que pueda causar su

operación no deseada.

Anybus®Wireless Bridge II™Compliance Sheet 3 (3)

Anybus®Wireless Bridge II™

Additional certification and compliance information

COMPLIANCE SHEET

This document does not include complete instructions for the safe use of the described equipment. Make sure that

you have read and understood the original user documentation for the equipment before proceeding.

UL Ordinary Locations (Ord.Loc.)

Anybus Wireless Bridge II modules are certified for use in ordinary locations in compliance with the

following standards:

• UL 61010-1 SAFETY REQUIREMENTS FOR ELECTRICAL EQUIPMENT FOR MEASUREMENT,

CONTROL, AND LABORATORY USE - PART 1: GENERAL REQUIREMENTS - Edition 3 - Revision

Date 2015/07/15

• UL 61010-2-201 STANDARD FOR SAFETY REQUIREMENTS FOR ELECTRICAL EQUIPMENT FOR

MEASUREMENT, CONTROL, AND LABORATORY USE - PART 2-201: PARTICULAR

REQUIREMENTS FOR CONTROL EQUIPMENT - Edition 1 - Issue Date 2014/01/24

• CSA C22.2 NO. 61010-1-12 SAFETY REQUIREMENTS FOR ELECTRICAL EQUIPMENT FOR

MEASUREMENT, CONTROL, AND LABORATORY USE. PT. 1, GENERAL REQUIREMENTS -

Edition 3 - Revision Date 2015/07/01

• CSA C22.2 NO. 61010-2-201:14 SAFETY REQUIREMENTS FOR ELECTRICAL EQUIPMENT FOR

MEASUREMENT, CONTROL, AND LABORATORY USE - PART 2-201: PARTICULAR

REQUIREMENTS FOR CONTROL EQUIPMENT - Edition 1 - Issue Date 2014/01/01

The certification number of Anybus Wireless Bridge II certified modules according to Ord.Loc. certification

is:

• E214107

According to the standards listed above, Anybus Wireless Bridge II modules are certified with the following

marking:

According to the standards listed above, the Anybus Wireless Bridge II modules shall be supplied by a

CLASS 2 / SELV classified power supply.

La page est en cours de chargement...

HMS Anybus Wireless Bridge II Startup Manual

Marque: HMS

Modèle: Anybus Wireless Bridge II

Taper: Startup Manual

Télécharger le PDF

rapport

dans d''autres langues

English: HMS Anybus Wireless Bridge II

HMS Anybus Wireless Bridge II Startup Manual

HMS Anybus Wireless Bridge II Startup Manual

dans d''autres langues

Autres documents