Redcat Racing RER12376 Le manuel du propriétaire

WARNING:

To avoid short circuits, ensure that all wires & connections are well insulated and there is proper contact at all connections. Read through

the entire manual before operating and ensure all electronics are installed correctly. To avoid accidents, we recommend setting the

vehicle on a stand, with the tires free from any contact, while connecting and adjusting electronics. Stop usage and unplug the battery

immediately if the ESC exceeds 90ºC/194ºF as this may damage both the ESC and motor.

Disconnect the battery after use. The ESC continuously draws current from the battery (even if the ESC is turned off). If left plugged in

for long periods of time, the battery will completely discharge, which may result in damage to the battery or ESC. This WILL NOT be

covered under warranty.

FEATURES:

Completely water-proof and dust-proof.

(Remove the cooling fan when running car in wet conditions. If the ESC gets wet, clean and dry thoroughly to avoid damage from the

oxidation of copper connectors).

External Programming Port (EPP), easily connect to a program card, and also works as power port for cooling fan.

Excellent start-up, acceleration and linearity features.

The built-in switching mode BEC is powerful enough to supply all electronic equipment with a reliable power source.

There is a mounting stand for installing the ESC on chassis easily and firmly.

Proportional ABS brake function with 5 steps of maximum brake force adjustment and 8 steps of drag-brake force adjustment. Also

compatible with the mechanical disc-brake system.

Multiple protection features: Low voltage cut-off protection / Over-heat protection / Throttle signal loss protection / Motor blocked

protection.

Model:

Cont./Peak Current:

LIPO/NiMH Cells:

Applications:

Built in BEC:

Size / Weight:

Programming Port:

Motor Type:

Motor Limit:

Resistance:

WP-8BL150-RTR

150A/950A

8-18 Cells NiMH 3-6S LiPo

1/8 Touring Car, Truggy, Buggy, Monster Truck

6V/5A, Switch mode

59.5(L) × 48(W) × 42(H) / 178g

FAN / PRG Port

Sensored / Sensorless Brushless Motor (only in sensorless mode)

4S LiPo 4274 size motor KV3000

6S LiPo 4274 size motor KV2400

0.00035 ohm

Specs:

NOTE: The cooling fans of ESC is supplied by the built-in BEC, so it is always working under 6V .

RCR-2CENR RADIO SYSTEM

ESC

ESC GUIDE

TM

14

Programming

Calibration

CH1

(A) (A)

(B) (B)

(C) (C)

(+) (+)

(

-

) (

-

)

Move the throttle trigger

to the neutral position and

press the SET button.

The Green

LED flashes

once and

motor emits

“Beep”

tone.

Pull the throttle trigger

to the end position of

forward and press the

SET button.

The Green

LED flashes

twice and

motor emits

“Beep-Beep”

tone.

Push the throttle trigger

to the end position of

reverse and press the

SET button.

The Green LED

flashes three

times and

motor emits

“Beep-Beep-

Beep” tone.

1. Turn on the transmitter, set parameters on the throttle channel like

“D/R”, “EPA” and “ATL” to 100% and the throttle “TRIM” to “0”. Disable

the “ABS braking function”.

2. Start with the transmitter on and the ESC turned off but connected to

a battery. While holding the SET button, Turn ON the ESC, then release

the SET button when you see the RED LED on the ESC start to flash

(Note: the motor beeps at the same time). (The ESC will enter the

programming mode if the SET button is not released within 3 seconds,

which will then require you to restart from step 1.)

Press and hold the

SET button Turn ON the ESC Release the

SET button

once the LED

flashes.

The Red

LED

flashes

1. Turn on the transmitter.

2. Press and hold the set button on the ESC ON/OFF switch.

3. Turn ON the ESC.

4. Continue to hold the set button until the Green LED flashes the

number of times that corresponds with the item # you wish to

adjust. Refer to the “Item #” column of the chart to determine the

number of Green LED flashes needed.

(1 flash =

Running Mode, 2 flashes = Drag Brake Force, etc.)

Press and hold

the SET

button

Turn ON the ESC

The Green

LED flashes.

3. To set the neutral point, leave the throttle trigger at the neutral position, press the SET button. The RED LED dies out and the GREEN LED flashes 1

time and the motor beeps 1 time to accept the neutral position.

4. To set the full throttle endpoint, pull the throttle trigger to the full throttle position and press the SET button. The GREEN LED blinks 2 times and the

motor beeps 2 times to accept the full throttle endpoint, then release the set button.

5. To set the full brake endpoint, push the throttle trigger to the full brake position, press the SET button. The GREEN LED blinks 3 times and the motor

beeps 3 times to accept the full brake endpoint. Release the trigger back to the neutral point. (The motor can be started 3 seconds after the

ESC/Radio calibration is complete)

Programmable

Items

Programmable Value

1 2 3 4 5 6 7 8 9

1. Running Mode Forward

with Brake

Forward/Reverse

with Brake

Forward and

Reverse

2. Drag Brake Force 0% 5% 10% 20% 40% 60% 80% 100%

3. Low Voltage

Cut-Off Threshold Non-Protection 2.6V/Cell 2.8V/Cell 3.0V/

Cell

3.2V/

Cell

3.4V/

Cell

4. Start Mode(Punch) Level 1 Level 2 Level 3 Level 4Level 5Level 6 Level 7 Level 8 Level 9

5. Max Brake Force 25% 50% 75% 100% Disable

NOTE: The shaded boxes are default settings

RCR-2CENR RADIO SYSTEM

ESC

TM

15

Battery

Battery Battery

Jumper Wire

Programming Flow Chart

Programming (Continued)

5. The Red LED will flash the number of times that corresponds to the number of the

option listed along the top of the chart. (1 flash = Option 1, 2 flashes = Option 2, etc.)

6. Press and release the set button until the desired number of Red flashes is achieved.

7. To finish set up, turn OFF the ESC.

8. You can now power the ESC back on. The settings should now be saved.

9. Repeat steps 1-8 for each setting you wish to adjust.

Press and release

the SET button

once the desired

number of Red

flashes is

reached.

Turn off

the ESC.

The Red LED

flashes. The

number of

flashes indicates

the program

option on the

chart.

Turn OFF the ESC,

Turn ON the transmitter

Hold the SET key,

Switch ON the ESC

Red LED flashes

Green LED flashes

1 time

Green LED flashes

2 times

Green LED flashes

3 times

Green LED flashes

N times

Enter the 1st item

“Running Mode”

Enter the 2nd item

“Drag Brake Force”

Enter the 3rd item

“Low Voltage Cut-Off”

Enter the Nth item

Red LED flashes 1 time to choose

“Forward with Brake”

Red LED flashes 2 times to choose

“Forward/Reverse with Brake”

Red LED flashes 3 times to choose

“Forward with Reverse”

Red LED flashes 1 time to choose 0%

Red LED flashes 2 times to choose 5%

Red LED flashes 3 times to choose 10%

Red LED flashes 4 times to choose 20%

Red LED flashes 5 times to choose 40%

Red LED flashes 6 times to choose 60%

Red LED flashes 7 times to choose 80%

Red LED flashes 8 times to choose 100%

Red LED flashes 1 time to choose “None”

Red LED flashes 2 times to choose “2.6V”

Red LED flashes 3 times to choose “2.8V”

Red LED flashes 4 times to choose “3.0V”

Red LED flashes 5 times to choose “3.2V”

Red LED flashes 6 times to choose “3.4V”

Press SET key to choose the value, the # of RED

LED flashes means the # of the value (1 flash =

the 1st value, 2 flashes = the 2nd value....)

Press SET key to choose the programmable value,

the RED LED flashes the # of the value you are

choosing. (1 flash = the 1st value, 2 flashes = the 2nd

value....)

Enter the corresponding

programmable item, the RED

LED flashes the current # value

of this item

Finish programming, switch OFF the ESC, then back ON again

The following steps are just like the above steps...........

Release

SET key

Release

SET key

Release

SET key

Release

SET key

Press

SET key

Press

SET key

Press

SET key

Press

SET key

Hold SET key for 3 more seconds

RCR-2CENR RADIO SYSTEM

ESC

TM

16

Programming (Continued)

Programmable Items Description

Using an Optional Program Card (Not Included)

1. Running Mode: In “Forward with Brake” mode, the car can go forward and brake, but cannot go backward, this mode is suitable for

competition. “Forward/Reverse with Brake” mode provides the reverse function, which is suitable for daily training.

Note: “Forward/Reverse with Brake” mode uses “Double-click” method to enter reverse. When you move the throttle trigger from the

forward zone to the reverse zone for the first time (The 1st “click”), the ESC begins to brake the motor, the motor slows down but it is still

running, not completely stopped, so the reverse function does NOT happen immediately. When the throttle trigger is moved to the

backward zone again (The 2nd “click”), if the vehicle is stopped, the reverse function will engage, driving the vehicle backward. The

“Double-Click” method prevents accidentally sending the vehicle into reverse while trying to brake.

Note: Any time during braking or reversing, if the throttle trigger is moved to forward zone, the motor will run forward at once.

“Forward/Reverse” mode uses “Single-click” to make the car go backward. When you move the throttle trigger from forward zone to

reverse zone, the car will go backward immediately. This mode is usually used for the Rock Crawlers and can be hard on the drivetrain.

2. Drag Brake Force: Set the amount of drag brake applied at neutral throttle to simulate the slight braking effect of a brushed

motor while coasting.

3. Low Voltage Cut-Off: The function prevents the lithium battery pack from over discharging. The ESC detects the battery’s voltage

at any time, if the voltage is lower than the threshold for 2 seconds, the output power will be cut off, and the red LED flashes: “-, -, -”.

4. Start Mode (Also called “Punch”): Select from “Level 1” to “Level 9”. Level 1 has a very soft start (minimum wheel spin), while level 9

has a very aggressive start (maximum wheel spin). From Level 1 to Level 9, the start force increases. Please note that if you choose

“Level 7” to “Level 9”, you must use a good quality battery with a high discharge rating (C-rating), otherwise these modes will just cause

the motor to tremble and hesitate. If this is happening, lower the “Punch” level, or use a battery with a higher “C-Rating”.

5. Maximum Brake Force: The ESC provides proportional braking. This setting increases or decreases the maximum amount of

braking. On the lowest setting, the vehicle will gradually come to a stop while full brake is applied on the transmitter. On the highest

setting, the vehicle will screech to a halt while full brake is applied on the transmitter. A high setting can potentially damage gears, so use

caution while setting this option. The “Disable” option inhibits the inherent brake function of the speed controller. “Disable” is used mostly

in nitro or gas vehicles using a mechanical disc-brake system driven by a servo.

Reset All Items To Default Values

At any time when the throttle is located in neutral zone (except in the throttle calibration or parameters program process), hold the

“SET” key for over 3 seconds, the red LED and green LED will flash at the same time, which means each programmable item has be reset

to its default value. The ESC will need to be restarted to complete the process.

In the program process, the motor will emit a “Beep” tone when the LED flashes.

A long flash and long “Beep---” tone is used to represent the number “5”, to easily identify items of a large number.

“A long flash” (Motor sounds “B---”) = the No. 5 item

“A long flash + a short flash” (Motor sounds “B---B”) = the No. 6 item

“A long flash + 2 short flashes” (Motor sounds “B---BB”) = the No. 7 item

“A long flash + 3 short flashes” (Motor sounds “B---BBB”) = the No. 8 item

“A long flash + 4 short flashes” (Motor sounds “B---BBBB”) = the No. 9 item

The Program Card is optional equipment which needs to be purchased separately. It has 3 digital LEDs to display the programmable items’

number and the options’ number. (Please refer to the user manual of the program card for detail info)

Attention! The Rx wire of the ESC (for connecting receiver) CANNOT be used to connect with the LED Program Card. Only use the fan

port between the terminals ABC to connect the Program Card to the ESC.

External fan port used

for connecting an

optional Programming

Card

RCR-2CENR RADIO SYSTEM

ESC

TM

17

The ESC will not power on and the

ON/OFF switch was turned ON. 1. No power is being supplied to the

ESC.

2. The ESC switch may be damaged.

1. Check if all ESC & connections are well

soldered and firmly connected.

2. Contact Redcat support.

The vehicle ran backward when you pulled

the throttle trigger towards you. 1. The radio “Throttle Reverse” switch

may be improperly set.

2. The motor rotation is incorrectly.

1. Switch the radio “Throttle Reverse”

switch.

2. Set the rotation in the ESC according to

the included instructions.

The motor suddenly stopped working, but

the steering still works.

The LVC protection or the thermal

protection may have been activated. Check the battery voltage and the ESC

temperature. Let cool and recharge

battery.

The motor accelerated suddenly,

stuttered or stopped during the

starting-up process.

1. The discharge capacity of the pack is

insufficient.

2. The RPM is too high, the gear ratio or

final drive ratio is incorrect.

3. Gear mesh too tight.

1. Use another pack with better discharge

capability.

2. Use stock motor, stock gearing, and

don’t pull heavy loads.

3. Reset gear mesh.

NiMH battery charge doesn't last as long

as it should. 1. ESC is set to LiPo battery.

2. NiMH battery is not charged completely.

3. NiMH battery is not holding a charge.

1. Refer to the ESC Guide to set the ESC

to NiMH battery.

2, 3. Completely charge the NiMH battery

with an appropriate NiMH charger.

LiPo battery won't recharge after running

the vehicle. 1. ESC is set to NiMH battery and the LiPo

battery was discharged below the safe

level.

2. Bad LiPo battery.

1. Refer to the ESC Guide and set the ESC

to LiPo battery. Properly dispose of the

LiPo battery, as it is no longer safe to use.

2. Replace the LiPo battery with a fully

charged, brand new battery. Dispose of

the bad battery in accordance to your

local laws.

Clicking noise while steering. 1. Servo gears stripped.

2. Servo horn stripped. 1. Replace servo.

2. Replace servo horn.

Vehicle won't steer or move. 1. Battery pack not charged.

2. Battery wires loose.

3. Did not follow proper start-up

instructions.

1. Charge battery pack.

2. Plug in battery securely.

3. Follow Quick Start Guide for proper

start-up sequence.

Vehicle turns to the side automatically. 1. Steering trim needs adjusting.

2. Steering servo horn needs realigning or

replaced.

3. Servo gears stripped.

4. Too much toe-out in front wheels.

1. Adjust transmitter steering trim.

2. Check servo horn, replace if worn or

stripped.

3. Replace servo.

4. Adjust steering linkage to lessen toe

amount.

Vehicle moves with no throttle input. 1. Throttle trim is not set properly.

2. Did not follow proper start-up instruc-

tions.

1. Set transmitter throttle trim.

2. Follow Quick Start Guide for proper

start-up sequence.

Vehicle steers to the left when you steer

to the right. 1. Steering reverse (on transmitter) is set

incorrectly.

2. You are driving towards yourself and it

just seems like it's backwards.

1. Set the steering reverse on transmitter.

2. Practice driving the vehicle to get used

to steering with different vehicle orienta-

tions. When driving towards yourself, it just

seems like the steering is backwards.

After the ESC was powered on and

finished LiPo cells detection (the GREEN

LED flashed N times), and then the RED

LED flashed rapidly.

1. The ESC didn't detect any throttle signal.

2. The neutral throttle value stored on your

ESC is different from the value stored on

the transmitter.

1. Check if the throttle wire is reversely

plugged in or in the wrong channel and if

the transmitter is turned on.

2. Re-calibrate the throttle range after you

release the

throttle trigger to the neutral position.

After powered on, the motor doesn’t work,

but emits “beep-beep-, beep-beep-”

alert tone. (Every “beep-beep-” has

a time interval of 1 second )

Input voltage is abnormal, too high or

too low Check the voltage of the battery pack

Grinding sound. 1. Gear mesh too loose.

2. Gears worn. 1. Reset gear mesh.

2. Replace gears.

TROUBLE POSSIBLE CAUSE POSSIBLE SOLUTIONS

RCR-2CENR RADIO SYSTEM

TROUBLESHOOTING

?

TM

18

La page charge ...

Redcat Racing RER12376 Le manuel du propriétaire

Redcat Racing RER12376 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents