GL iNet GL-AXT1800 Mode d'emploi

Marque
GL iNet
Modèle
GL-AXT1800
Taper
Mode d'emploi
When powered up, your router will broadcast
both 2.4G and 5G Wi-Fi signal with the SSID:
GL-AXT1800-xxx and GL-AXT1800-xxx-5G.
SETTING UP
Let’s get
started.
GL-AXT1800 / Slate AX
AXT1800 Wireless Router
Insert Cards & Power On
Set Up Router
Connect via Wi-Fi Connect via LAN
Visit http://192.168.8.1 in your browser to set
up your router; start by choosing your preferred
language.
Connect to the Wi-Fi called GL-AXT1800-xxx
or GL-AXT1800-xxx-5G, and then input the
default Wi-Fi password which is printed on
the bottom label of the router.
Search the SSID and connect to it
Plug the cable connecting
to your computer into LAN port
Hot plug for MicroSD card is not
supported for this router.
TF Card or MicroSD
Card (Optional)
After Inserting card,
plug in power cable
ver. 20220526
SUPPORT WARRANTY
Technical Supports
- Email to [email protected]
- Message us on our Facebook: facebook.com/gl.inet.wifi/
- Post questions in our forum: forum.gl-inet.com
- Ask professionals in other forums e.g. OpenWrt, LEDE or other professional websites
Repair / Reset
If you cannot access the web-based setup page or cannot connect to the
router, you can press the Reset button:
Press and hold for 3 seconds and then release to repair your network.
The light will turn blue and flash slowly until your network recovers.
Press and hold for 10 seconds, and then release to reset the router
to factory settings. The light will turn blue and flash rapidly. All data
will be cleared when the light becomes solid blue.
For further questions, you can get help from the following ways:
For more detailed and updated instructions, please visit our website docs.gl-inet.com
https://docs.gl-inet.com/en/4/
GL Technologies (Hong Kong) Limited
Unit 203, 2/F, Building 19W, 19 Science Park West
Avenue, Hong Kong Science Park,
Pak Shek Kok, N.T., Hong Kong
Hong Kong Office
Shenzhen Guanglianzhitong Tech Co., Ltd.
Room 305 - 306, Skyworth Digital Building, Shiyan Street,
Baoan District, Shenzhen, China, 518000
( +86-0755-86606126 )
Shenzhen Office
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter.
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
3. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help important announcement.
FCC ID: 2AFIW-AXT1800
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s
licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement
économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
(1) L’appareil ne doit pas produire de brouillage;
(2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed
and operated with minimum distance 20cm between the radiator and your body.
Cet équipement est conforme aux limites d'exposition aux radiations IC CNR-102 établies pour un environnement non contrôlé. Cet équipement
doit être installé et utilisé avec une distance minimale de 20 cm entre le radiateur et votre corps.
The user manual for LE-LAN devices shall contain instructions related to the restrictions mentioned in the above sections, namely that:
i. the device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel
mobile satellite systems;
i. le dispositif utilisé dans la bande 5150-5250 MHz est réservé à une utilisation en intérieur afin de réduire le risque de brouillage préjudiciable
aux systèmes mobiles par satellite dans le même canal;
The functions of Wireless Access Systems including Radio Local Area Networks(WAS/RLANs) within the band 5150-5350 MHz for this device are
restricted to indoor use only within all European Union countries.
2.4G Wi-Fi 2412MHz-2472MHz, 2422MHz-2462MHz; 5G Wi-Fi: U-NII-1:5180-5240MHz, 5190-5230MHz, 5210MHz; U-NII-2A: 5260-5320MHz,
5270-5310MHz, 5290MHz; U-NII-2C: 5500-5700MHz, , 5510-5670MHz, 5530-5610MHz; 5.8G Wi-Fi: 5745MHz-5825MHz,5755-5795MHz,5775MHz
Max Output Power:
2.4G Wi-Fi19.18dBm; 5G Wi-Fi: 29.71 dBm; 5.8G Wi-Fi: 13.67 dBm
Hereby, GL TECHNOLOGIES (HONG KONG) LIMITED declares that the radio equipment type [AXT1800 Wireless Router, GL-AXT1800] is in
compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU.The full text of the EU declaration of
conformity is available at the following internet address: https://www.gl-inet.com/products/certificate
We provide one year limited warranty for routers and 3-month limited warranty for accessories.
Extra warranty may apply according to the local law in which the product purchase took place.
Highly recommend using the included 5V/4A power adapter.
Any damage to the router caused by not following the instructions will render this warranty null
and void.
Any damage to the router caused by modifying the PCBA, components or case will render this
warranty null and void.
Issues caused by the use of third-party firmware may not get official support from us.
Any damage to the router caused by inappropriate use, e.g. inappropriate voltage input, high
temperature, dropping in the water or on the ground will render this warranty null and void.
Pictures on the instructions are only for reference. We reserve the right to change or modify
these materials without further notice.
MicroSD Card
(Optional)
Reset button
Mode button
USB3.0 port
Power port
LAN Ethernet ports
WAN Ethernet port
Light
(Solid white light
means the router
is working well)
LV LI LT LU MT NO PL PT RO SK SI ES SE CH NL UK(NI)
FI FR DE EL HU IS IE ITAT BE BG HR CY CZ DK EE
  • Page 1 1
  • Page 2 2

GL iNet GL-AXT1800 Mode d'emploi

Marque
GL iNet
Modèle
GL-AXT1800
Taper
Mode d'emploi
Télécharger le PDF
rapport

dans d''autres langues

Autres documents