Geolocation Module User Manual
Part Number: LBEU5ZZ1WL
LBEU5ZZ1WL has been FCC/ISED certified as Single Modular Approval with the following IDs.
FCC ID: VPYLB1WL IC: 772C-LB1WL
The module is limited to OEM installation ONLY. The OEM integrator is responsible for ensuring that the end-user has
no manual instruction to remove or install module.
Therefore, the final host product must be submitted to Murata for confirmation that the installation for the module into
the host is in compliance with regulations of FCC and IC Canada. Specially, if an antenna other than the model
documented in the Filing is used, a Class 2 Permissive Change must be filed with the FCC.
Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the
equipment.
This module has been approved by FCC to operate with the antenna types with the maximum permissible
gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain
indicated for that type, are strictly prohibited for use with this device. The following antennas have been
certified in combination with the module. Refer to the next pages for the antenna application guidance.
(a) Whip antenna ANT-SS900 for LoRa with a peak gain of 0.0dBi;
(b) Whip antenna W1010 for 2.4GHz WLAN and Bluetooth LE with a peak gain of 1.7dBi;
(c) Passive antenna for GNSS with a peak gain of 0.4dBi;
Antenna Application Guidance
Bluetooth/WLAN GNSS LoRa
Unit: mm
Antenna Application Guidance
Ant trace Length (mm) Width (mm)
LoRa 56.29 0.27
BLE/WiFi 21.18 0.27
GNSS 26.92 0.27
Antenna feeding traces on PCB
FCC Statements
Please take attention that changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
This equipment complies with FCC/IC RSS-102 radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance 20cm between
the radiator & your body.
When the FCC ID is not visible when the module is installed inside another device, then the outside of the
device into which the module is installed must also display a label referring to the enclosed module. This
exterior label can use wording ”Contains transmitter module FCC ID: VPYLB1WL” or “Contains FCC ID:
VPYLB1WL”.
FCC Statements (cont.)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
IC Statements
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation
of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radioexempts de
licence. L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type
and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio
interference to other users, the antenna type and its gain should be so chosen that the equivalent
isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut
fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par
Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres
utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée
équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication
satisfaisante.
IC Statements (cont.)
This equipment complies with FCC/IC RSS-102 radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm between the
radiator & your body.
ce matériel est conforme aux limites de dose d'exposition aux rayonnements, FCC / CNR-102 énoncée
dans un autre environnement.cette eqipment devrait être installé et exploité avec distance minimale de
20 entre le radiateur et votre corps.
When the Industry Canada certification number is not visible when the module is installed inside another
device, then the outside of the device into which the module is installed must also display a label referring
to the enclosed module. This exterior label can be use wording ”Contains transmitter module IC: 772C-
LB1WL” or “Contains IC: 772C-LB1WL”.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
dans d''autres langues
- English: Murata LBEU5ZZ1WL User manual
Documents connexes
Autres documents
-
GSD WC5EM2601F Dual Band WiFi Module Manuel utilisateur
-
GSD WC0PR1601 Le manuel du propriétaire
-
GSD WXT2AM2101 WIFI+BT Module IEEE Manuel utilisateur
-
Multitech MTCDT-L4N1-247A-915-US Mode d'emploi
-
GSD W37 Manuel utilisateur
-
Telit Wireless Solutions LE910-SVG Manuel utilisateur
-
-
GSD WXT5BM2511 Le manuel du propriétaire
