Senix HTX2-M Manuel utilisateur

20V MAX LITHIUM-ION

CORDLESS HEDGE TRIMMER

Operator’s manual

Model: HTX2-M

HTX2-M-0

For customer support, please call 1-800-261-3981 or send email to:

[email protected]

SAVE THIS MANUAL FOR FUTURE REFERENCE.

ORIGINAL INSTRUCTIONS

TM

EN - 2 WWW.SENIXTOOLS.COM

1

2 3

4

5

6

78

910

1

23

3 - ENWWW.SENIXTOOLS.COM

4

6

98

7

5

Interlocking Switch

Light Button

Switch Trigger

EN - 4 WWW.SENIXTOOLS.COM

10

Cutting teeth Guard teeth

5 - ENWWW.SENIXTOOLS.COM

TABLE OF CONTENTS

SAFETY & INTERNATIONAL SYMBOLS .......................... 5

SAFETY INSTRUCTIONS .................................................. 6

KNOW YOUR UNIT .......................................................... 15

SPECIFICATIONS* .......................................................... 15

ASSEMBLY ...................................................................... 16

OPERATION ..................................................................... 16

MAINTENANCE ............................................................... 18

TROUBLESHOOTING ..................................................... 20

WARRANTY ..................................................................... 21

SAFETY & INTERNATIONAL

SYMBOLS

Explanation of Safety & international symbols describes

safety and international symbols and pictographs that may

appear on this product. Read the operator’s manual for

complete safety, assembly, operating and maintenance and

repair information.

Caution / Warning.

To reduce the risk of injury, user must read

instruction manual.

Wear eye protection.

Wear head protection.

DANGER – Keep hands away from blade.

Do not use in rain or wet conditions.

Wear safety footwear.

Wear protective gloves.

Do not dispose of battery packs in rivers or

immerse in water.

Do not dispose of battery packs in fire. They

will explode and cause injury.

Use and store the battery within an temperature

below 122°F(50°C).

Do not disassemble, crush, heat above

212°F(100°C); Never expose the battery to

microwaves or high pressures.

Keep bystanders a safe distance away from

the work area.

Indoor use only. Only use battery charger

indoors.

EN - 6 WWW.SENIXTOOLS.COM

SAFETY INSTRUCTIONS

All Operators Must Read These

Instructions Before Use.

Always follow these safety

guidelines. Failure to do so may

result in serious bodily injury or

death.

DANGER!

This indicates a hazardous situation,

which, if not followed, will result in

serious injury or death.

WARNING!

This indicates a hazardous situation,

which, if not followed, could result in

serious injury or death.

CAUTION!

This indicates a hazardous situation,

which, if not followed, could result in

minor or moderate injury.

GENERAL POWER TOOL SAFETY

WARNINGS

WARNING!

Read all safety warnings and all

instructions. Failure to follow the

warnings and instructions may result

in electric shock, re and/or serious

injury.

Save all warnings and

instructions for future reference.

The term "power tool" in

the warnings refers to your

mainsoperated (corded) power tool

or battery-operated (cordless) power

tool.

1) Work Area Safety

a. Keep work area clean and well

lit – Cluttered or dark areas invite

accidents.

b. Do not operate power tools in

explosive atmospheres, such

as in the presence of flammable

liquids, gases or dust – Power

tools create sparks which may

ignite the dust or fumes.

c. Keep children and bystanders

away while operating a power

tool – Distractions can cause you

to lose control.

2) Electrical Safety

a. Power tool plugs must match the

outlet. Never modify the plug in

any way. Do not use any adapter

plugs with earthed (grounded)

power tools. Unmodified plugs

and matching outlets will reduce

risk of electric shock.

b. Avoid body contact with earthed

or grounded surfaces, such

as pipes, radiators, ranges

and refrigerators – There is

an increased risk of electric

shock if your body is earthed or

grounded.

7 - ENWWW.SENIXTOOLS.COM

reduce personal injuries.

c. Avoid accidental starting. Ensure

the switch is in the off-position

before plugging in – Carrying

power tools with your finger on

the switch or plugging in power

tools that have the switch on

invites accidents.

d. Remove any adjusting key or

wrench before turning the power

tool on – A wrench or a key left

attached to a rotating part of the

power tool may result in personal

injury.

e. Do not overreach. Keep proper

footing and balance at all times

– This enables better control of

the power tool in unexpected

situations.

f. Dress properly. Do not wear

loose clothing or jewelry. Keep

your hair, clothing and gloves

away from moving parts – Loose

clothes, jewelry or long hair can

be caught in moving parts.

g. If devices are provided for the

connection of dust extraction and

collection facilities, ensure these

are connected and properly

used – Use of dust collection can

reduce dust-related hazards.

4) Power Tool Use + Care

a. Do not force the power tool. Use

c. Do not expose power tools to

rain or wet conditions – Water

entering a power tool will

increase the risk of electric

shock.

d. Do not abuse the cord. Never use

the cord for carrying, pulling or

unplugging the power tool. Keep

cord away from heat, oil, sharp

edges or moving parts. Damaged

or entangled cords increase the

risk of electric shock.

e . When operating a power tool

outdoors, use an extension cord

suitable for outdoor use. Use of

a cord suitable for outdoor use

reduces the risk of electric shock.

3) Personal Safety

a. Stay alert, watch what you are

doing and use common sense

when operating a power tool. Do

not use a power tool while you

are tired or under the influence

of drugs, alcohol or medication

– A moment of inattention while

operating power tools may result

in serious personal injury.

b. Use safety equipment. Always

wear eye protection – Safety

equipment such as dust mask,

non-skid safety shoes, hard

hat, or hearing protection used

for appropriate conditions will

EN - 8 WWW.SENIXTOOLS.COM

the correct power tool for your

application – The correct power

tool will do the job better and

safer at the rate for which it was

designed.

b. Do not use the power tool if the

switch does not turn it on and

off – Any power tool that cannot

be controlled with the switch is

dangerous and must be repaired.

c. Disconnect the battery pack

from the power tool before

making any adjustments,

changing accessories, or storing

power tools – Such preventive

safety measures reduce the

risk of starting the power tool

accidentally.

d. Store idle power tools out of the

reach of children and do not

allow persons unfamiliar with the

power tool or these instructions

to operate the power tool –

Power tools are dangerous in the

hands of untrained users.

e. Maintain power tools. Check

for misalignment or binding of

moving parts, breakage of parts

and any other condition that may

affect the power tool’s operation.

If damaged, have the power

tool repaired before use – Many

accidents are caused by poorly

maintained power tools.

f. Keep cutting tools sharp and

clean – Properly maintained

cutting tools with sharp cutting

edges are less likely to bind and

are easier to control.

g. Use the power tool, accessories

and tool bits etc., in accordance

with these instructions and in

the manner intended for the

particular type of power tool,

taking into account the working

conditions and the work to be

performed – Use of the power

tool for operations different from

those intended could result in a

hazardous situation.

5) Battery tool use and care

a. Recharge only with the charger

specified by the manufacturer. A

charger that is suitable for one

type of battery pack may create

a risk of fire when used with

another battery pack.

b. Use power tools only with

specifically designated battery

packs. Use of any other battery

packs may create a risk of injury

and fire.

c. When battery pack is not in use,

keep it away from other metal

objects, like paper clips, coins,

keys, nails, screws or other small

metal objects, that can make a

9 - ENWWW.SENIXTOOLS.COM

making adjustments, changing

accessories, storing or servicing

the appliance. Unexpected

actuation of the appliance while

clearing jammed material or

servicing may result in serious

personal injury.

c. Recharge only with the charger

specified by the manufacturer. A

charger that is suitable for one

type of battery pack may create

a risk of fire when used with

another battery pack.

d. Use appliances only with

specifically designated battery

packs. Use of any other battery

packs may create a risk of injury

and fire.

e. When battery pack is not in use,

keep it away from other metal

objects, like paper clips, coins,

keys, nails, screws or other small

metal objects, that can make a

connection from one terminal

to another. Shorting the battery

terminals together may cause

burns or a fire.

f. Under abusive conditions,

liquid may be ejected from the

battery; avoid contact. If contact

accidentally occurs, flush with

water. If liquid contacts eyes,

additionally seek medical help.

Liquid ejected from the battery

connection from one terminal

to another. Shorting the battery

terminals together may cause

burns or a fire.

d. Under abusive conditions,

liquid may be ejected from the

battery; avoid contact. If contact

accidentally occurs, flush with

water. If liquid contacts eyes,

additionally seek medical help.

Liquid ejected from the battery

may cause irritation or burns.

6) Service

a. Have your power tool serviced by

a qualified repair person using

only identical replacement parts.

This will ensure that the safety of

the power tool is maintained.

WARNINGS FOR ALL BATTERY-

OPERATED APPLIANCES

a. Prevent unintentional starting.

Ensure the power switch is in the

off-position before connecting

to battery pack, picking up or

carrying the appliance. Carrying

the appliance with your finger on

the power switch or energizing

the appliance that has the power

switch on invites accidents.

b. Make sure the power switch is off

and the battery pack is removed

before clearing jammed material,

EN - 10 WWW.SENIXTOOLS.COM

may cause irritation or burns.

(This advice is considered

correct for conventional NiMh,

NiCd, lead acid and lithium-

ion cell types. If this advice

is incorrect for a cell design

that differs from these, then

the correct advice may be

substituted.)

g. Do not use a battery pack or

appliance that is damaged

or modified. Damaged or

modified batteries may exhibit

unpredictable behavior resulting

in fire, explosion or risk of injury.

h. Do not expose a battery pack or

appliance to fire or excessive

temperature. Exposure to fire

or temperature above 130°C

may cause explosion. The

temperature of 130°C can be

replaced by the temperature of

265°F.

i. Follow all charging instructions

and do not charge the battery

pack or appliance outside of

the temperature range specified

in the instructions. Charging

improperly or at temperatures

outside of the specified range

may damage the battery and

increase the risk of fire.

j. Have servicing performed by a

qualified repair person using only

identical replacement parts. This

will ensure that the safety of the

product is maintained.

k. Do not modify or attempt to

repair the appliance or the

battery pack (as applicable)

except as indicated in the

instructions for use and care.

ADDITIONAL SAFETY RULES

FOR HEDGE TRIMMER

a. Use both hands when operating

the hedge trimmer. Using one

hand could cause loss of control

and result in serious personal

injury.

b. Keep all parts of the body

away from the cutter blade.

Do not remove cut material or

hold material to be cut when

blades are moving. Make sure

the switch is off when clearing

jammed material. A moment of

inattention while operating the

hedge trimmer may result in

serious personal injury.

c. Carry the hedge trimmer by the

handle with the cutter blade

stopped. When transporting or

storing the hedge trimmer always

fit the cutting device cover.

Proper handling of the hedge

trimmer will reduce possible

personal injury from the cutter

11 - ENWWW.SENIXTOOLS.COM

is removed and the moving

hazardous parts have come to a

complete stop.

j. Do not using the machine in bad

weather conditions especially

when there is a risk of lightning.

k. Inspect the area to be cut and

remove any foreign objects

that will influence your cutting.

If the foreign objects can not

be removed, e.g. wire fences,

please mark and remember it

to avoid toughing them during

cutting.

l. Ensure that the hedge trimmer is

correctly located in a designated

working position before starting

the motor.

m. Always ensure that the air vents

are kept clear of debris.

n. If the cutting attachment strikes

any foreign object or the product

starts making any unusual noise

or vibration, switch the product

off, remove the battery, allow

the product to stop and take the

following steps:

– inspect for damage;

– check for, and tighten, any loose

parts;

– have any damaged parts

replaced or repaired with parts

having equivalent specifications.

blades.

d. Hold the power tool by insulated

gripping surfaces only, because

the cutter blade may contact

hidden wiring or its own cord.

Cutter blades contacting a ²live²

wire may make exposed metal

parts of the power tool ²live²

and could give the operator an

electric shock.

e. Keep cable away from cutting

area. During operation the cable

may be hidden in shrubs and can

be accidentally cut by the blade.

f. Remove any blade that has been

damaged. Always make sure that

the blade is installed correctly

and securely fastened before

each use. Failure to do so can

cause serious injury.

g. Service on the product must

be performed by qualified

repair personnel only. Service

or maintenance performed by

unqualified personnel could

result in injury to the user or

damage to the product.

h. Do not overreach and to keep

the balance at all times. Always

be sure of the footing on slopes.

Walk when operating the power

tool, never run.

i. Do not touch moving hazardous

parts before the battery pack

EN - 12 WWW.SENIXTOOLS.COM

o. Never allow people unfamiliar

with these instructions or

children to use the product. Local

regulations can restrict the age

of the operator.

p. Keep in mind that the operator or

user is responsible for accidents

or hazards occurring to other

people or their property.

BATTERY PACK SAFETY

WARNINGS

• Ensure the switch is in the off

position before inserting battery

pack. Inserting the battery pack

into machines that have the

switch on can cause accidents.

• Use only original battery packs

intended specifically for this

machine. Use of any other

battery packs may create a risk

of injury and fire.

• Do not open the battery. Danger

of short-circuiting.

• Protect the battery against heat

(e.g., against continuous intense

sunlight and fire) water and

moisture. Danger of explosion.

• In case of damage and improper

use of the battery, vapours may

be emitted. Ventilate the area

and seek medical help in case

of complaints. The vapours can

irritate the respiratory system.

• Use the battery pack only in

conjunction with this product and/

or product family. This measure

alone protects the battery against

dangerous overload.

• The battery can be damaged by

pointed objects such as nails or

screwdrivers or by force applied

externally. An internal short

circuit can occur and the battery

can burn, smoke, explode or

overheat.

• Do not short-circuit the battery.

There is danger of explosion.

• Store and use the battery only

within a temperature range

between -4°F(–20°C) to

77°F(25°C). As an example, do

not leave the battery in the car in

summer.

• Occasionally clean the venting

slots and contact pins of the

battery pack using a soft, clean

and dry brush.

BATTERY CHARGER SAFETY

WARNINGS

Read all safety warnings and

instructions before using the

charger. Only for indoor use!

• This appliance is not intended

for use by children and persons

with physical, sensory or

mental limitations or a lack

13 - ENWWW.SENIXTOOLS.COM

of experience or knowledge.

This appliance can be used by

children aged from 8 years and

above and persons with reduced

physical, sensory or mental

capabilities or lack of experience

and knowledge if they have been

given supervision or instruction

concerning use of the appliance

in a safe way and understand

the hazards involved. Children

shall not play with the appliance.

Cleaning and user maintenance

shall not be made by children

without supervision.

• The supply cord cannot be

replaced. If the cord is damaged

the appliance should be

scrapped.

• Only charge the Lithium-Ion

battery pack as mentioned in

this instruction manual. Do

not charge non-rechargeable

batteries.

• The battery and charger must be

placed in a well ventilated area.

• If the supply cord is damaged,

it must be replaced by the

manufacturer, its service agent

or similarly qualified persons in

order to avoid a hazard.

• Do not operate the battery

charger on easily inflammable

surfaces (e. g., paper, textiles,

etc.) or surroundings. The

heating of the battery charger

during the charging process can

pose a fire hazard.

• Do not cover the ventilation slots

of the battery charger. Otherwise,

the battery charger can overheat

and no longer operate properly.

VIBRATION + NOISE REDUCTION

To reduce the impact of noise and

vibration emission, limit the time of

operation, use low-vibration and low-

noise operating modes as well as

wear personal protective equipment.

Take the following points into

account to minimise the vibration

and noise exposure risks.

• Only use the product as

intended by its design and these

instructions.

• Ensure that the product is

in good condition and well

maintained.

• Use correct attachments for the

product and ensure they are in

good condition.

• Keep tight grip on the handles/

grip surface.

• Maintain this product in

accordance with these

instructions and keep it well

lubricated (where appropriate).

• Plan your work schedule to

EN - 14 WWW.SENIXTOOLS.COM

spread any high vibration tool

use across a longer period of

time.

EMERGENCY

Familiarize yourself with the use

of this product by means of this

instruction manual. Memorize the

safety directions and follow them to

the letter. This will help to prevent

risks and hazards.

• Always be alert when using

this product, so that you can

recognize and handle risks early.

Fast intervention can prevent

serious injury and damage to

property.

• Switch off the product and

remove the battery pack if there

are malfunctions. Have the

product checked by a qualified

professional and repaired, if

necessary, before you operate it

again.

15 - ENWWW.SENIXTOOLS.COM

KNOW YOUR UNIT

APPLICATIONS

Model: HTX2-M

As a hedge trimmer:

Cutting and trimming hedges and bushes in domestic use.

1 Blade Cover

2 Cutting Blade

3 Guard

4 Front Handle

5 Interlocking Switch

6 Handle

7 Housing

8Switch Trigger

9 Unlock Button of Battery Pack

10 Battery Pack

NOTE:

HTX2-M-0 does not include the charger and the battery

pack.

SPECIFICATIONS*

Model HTX2-M

Input voltage 18V d.c.

No-load speed 2600spm

Cutting length 18in

Tooth space 1.1in

Cutting capacity 0.8in

Weight (without battery pack) 5.51lbs

Battery pack model for option B25X2 B50X2

Rated voltage 18V 18V

Rated capacity 2.5Ah 5.0Ah

Weight 0.74lbs 1.43lbs

Charger model CHX2

Rated input 100-240V ~ 50/60Hz

Rated output 21V, 2000mA

Charging time

(with 2.5 Ah battery) 85mins

Charging time

(with 5.0 Ah battery) 130mins

Protection class(for charger) / II

Weight 0.75lbs

Model HTX2-M-0

Input voltage 18V d.c.

No-load speed 2600spm

Cutting length 18in

Tooth space 1.1in

Cutting capacity 0.8in

Weight (without battery pack) 5.51lbs

Battery pack model Not included

Charger model Not included

EN - 16 WWW.SENIXTOOLS.COM

ASSEMBLY

1. Unpack all parts and lay them on a flat, stable surface:

2. Remove all packing materials and shipping devices, if

applicable.

3. The scope of delivery varies depending on the country

and purchased variant:

Model of HTX2-M-0.

• Hedge trimmer x1

• Blade Cover x1

• Screw x2

• Front Handle x1

• Instruction Manual x1

4. If you find that parts are missing or show damage do

not use the product but contact your dealer. Using an

incomplete or damaged product represents a hazard to

people and property.

5. Ensure that you have all the accessories and tools

needed for assembly and operation. This also includes

suitable personal protective equipment.

NOTE:

HTX2-M includes the charger and the battery pack.

HTX2-M-0 does not include the charger and the battery

pack.

WARNING:

Wear protective gloves for this assembly work

and always lay the product on a flat and stable

surface while assembling.

Follow the assembly instructions step-by-step

and use the pictures provided as a visual guide

to easily assemble the product!

Do not insert the battery pack before the power

tool is completely assembled or adjusted!

ASSEMBLING THE FRONT

HANDLE

WARNING:

To avoid serious personal injury and damage

to the unit, shut the unit off before removing or

installing an attachment.

1. Align and insert the front handle (Fig.2).

2. Fix the front handle with two screws (Fig.3).

3. Check if the handle is firmly seated in case of injury.

REMOVING THE BLADE COVER

Remove the blade cover before turning on the machine

(Fig.4).

It is recommended to cover the blade when your work is

finished.

INSTALLING/REMOVING THE

BATTERY PACK

WARNING:

Make sure battery pack snaps in place.

Failure to securely seat the battery pack could

cause the battery pack to fall out, resulting in

serious personal injury.

To install:

Align and slide the battery pack into the slots of the battery

docking port until it locks in place (Fig.5).

To remove:

Press the unlock button of battery pack and remove the

battery pack from the product.

OPERATION

WARNING:

Always wear eye, hearing, hand, foot and body

protection to reduce the risk of injury when

operating this unit. Keep all parts of your body

away from the rotating cutting attachment and

hot surfaces.

SWITCHING ON/OFF

Hold the product as in working condition.

To start the product, press the switch trigger and the

interlocking switch at the front handle at the same time.

To switch the product off, release the switch trigger or the

interlocking switch (Fig.6).

NOTE:

For safety reasons, both the interlocking switch and the

switch trigger must remain pressed during the entire

operation.

17 - ENWWW.SENIXTOOLS.COM

GENERAL

WARNING:

Always lubricate the cutting blade with protective

spray before use and storage.

1. Double check that all parts are properly fixed.

2. Check the product as well as accessories for damage

before each use. Do not use the product if it is damaged

or shows wear.

3. Ensure that the air vents are always unobstructed

and clear. Clean them if necessary with a soft brush.

Blocked air vents may lead to overheating and damage

the product

4. Wear eye, hearing, hand, foot and body protection.

5. Always hold the product on its handles. Keep the

handles dry and free from lubricant to ensure safe

holding.

6. Keep your body and feet in safety distance to cutting

head.

7. Inspect the area to be cut and remove any foreign

objects that will influence your cutting. If the foreign

objects can not be removed, e.g. wire fences, please

mark and remember it to avoid toughing them during

cutting.

8. Run the machine to top speed before cutting.

9. Switch the product off immediately if you are disturbed

while working by other people entering the working

area. Always let the product come to complete stop

before putting it down.

10. Do not overwork yourself. Take regular breaks to ensure

you can concentrate on the work and have full control

over the product.

NOTE:

In some countries regulations define at what time of the

day and on what special days products are allowed to be

used and what restrictions apply! Ask your community for

detailed information and observe the regulations in order

to preserve a peaceful neighborhood and avoid committing

administrative offences.

CUTTING TIPS

WARNING:

Never cut near electric cords or lines. If

blade jams on any electrical cord or line,

DO NOT TOUCH THE BLADE! IT CAN

BECOME ELECTRICALLY LIVE AND VERY

DANGEROUS. Continue to hold the hedge

trimmer by the insulated rear handle or lay it

down and away from you in a safe manner.

Disconnect the electrical service to the damaged

line or cord before attempting to free the blade

from the line or cord. Contact with the blade,

other conductive parts of the hedge trimmer, or

live electric cords or lines will result in death by

electrocution or serious injury.

• Clear the area to be cut before each use. Remove all

objects such as cords, lights, wire, or loose string which

can become entangled in the cutting blade and create a

risk of serious personal injury.

• Before starting the hedge trimmer, hold the unit with

both hands with the cutting blades directed away from

you. Always use the hedge trimmer properly.

• Do not force the hedge trimmer through heavy

shrubbery. This can cause the blades to bind and slow

down. If the blades slow down, reduce the pace.

• Do not try to cut stems or twigs that are larger than 3/4

in. thick, or those obviously too large to feed into the

cutting blade. Use a non-powered hand saw or pruning

saw to trim large stems.

• If blades do become jammed, stop the product, allow

the blades to stop and remove the battery pack before

attempting to remove the obstruction.

• If desired, you can use a string to help cut your hedge

level. Decide how high you want the hedge.

• Then, stretch a piece of string along the hedge at this

height. Trim the hedge just above this guide line of

string. Trim the side of a hedge so that it will be slightly

narrower at the top. More of the hedge will be exposed

when shaped this way, and it will be more uniform.

• Always hold hedge trimmer with both hands when

operating. Use a rm grip on the handles. Never hold

shrubs with one hand and operate the hedge trimmer

with the other. Improper operation of the hedge trimmer

could result in serious injury. The unit is used for cutting

in either direction in a slow, sweeping action from side

to side.

• Wear gloves when trimming thorny or prickly growth.

When trimming new growth, use a wide sweeping

action, so that the stems are fed directly into the cutting

blade. Older growth will have thicker stems and will be

trimmed easiest by using a sawing movement.

• The risk of the operation may occurs, such as the sharp

tree branches may cut the user's skin, the blade of

the unit may hurt the user's body. Always wear eye,

hearing, hand, foot and body protection to reduce the

risk of injury when operating this unit.

EN - 18 WWW.SENIXTOOLS.COM

HOW TO CHARGE THE BATTERY

PACK

WARNING:

This Lithium-Ion battery pack is shipped partially

charged. Fully charge the battery pack before

using it for the first time.

NOTE:

Charging batteries at a ambient temperature of 32°F(0°C)-

104°F(40°C).

1. Charge the Lithium-Ion battery pack only with the

correct charger.

2. Connect the charger to a power supply, the light

indicator of the charger turns red.

3. Align the raised ribs of the battery pack with the slot in

the charger.

4. Insert the battery pack into the charger, the light

indicator of the charger turns green and it flashes.

5. The charger will communicate with the battery pack to

evaluate the condition of the battery pack (Fig.7).

6. It is fully charged that the four lights of the battery turn

on. Disconnect the power supply from the charger.

Remove battery pack from the charger.

CHARGING INDICATOR

Press the light button (Fig.8) to check the battery pack

whether needs to charge.

Lights

Status

Lighted Off Blinking

The battery is at full

capacity.

The battery is at 75%

capacity.

The battery is at 50%

capacity and requires

charging.

The battery is at 25%

capacity and requires

charging soon.

The battery is less

than 5% capacity and

requires charging

immediately.

WARNING:

Malfunctions may occur when the four lights

blinking in turns.

OVERHEAT PROTECTION

When the tool/battery is overheated, the tool stops

automatically. In this situation, let the power tool/battery cool

before turning the tool on again.

OVERDISCHARGE PROTECTION

When the battery capacity is not enough, the tool stops

automatically. In this case, remove the battery from the tool

and charge the battery.

MAINTENANCE

WARNING:

Always switch the product off, remove the

battery pack and let the product cool down

before performing cleaning and maintenance

work!

Always wear eye, hearing, hand, foot and body

protection to reduce the risk of injury when

operating this unit.

Only perform cleaning and maintenance work

according to these instructions! All further works

must be performed by a qualied specialist!

And only use specied spare parts for

replacement.

LUBRICATING THE BLADE

WARNING:

Always allow the blades of the hedge trimmer to

come to a complete stop and pull out the battery

pack before lubricating. Failure to do so could

result in accidental starting causing possible

serious personal injury.

19 - ENWWW.SENIXTOOLS.COM

For easier operation and longer blade life, lubricate the

hedge trimmer blade before and after each use.

If you will not be using the hedge trimmer for an extended

time, it is advisable to oil the blade periodically.

Stop the hedge trimmer. Pull out the battery pack from the

product. Lay the hedge trimmer on a flat surface and apply

light weight machine oil along the edge of the top blade

(Fig.9).

SHARPENING THE BLADE

WARNING:

During the maintenance, users should take care of their

safety. Always wear eye, hearing, hand, foot and body

protection to reduce the risk of injury when operating this

unit. And check the unit that it can work normally after

the maintenance. If any deterioration occurs, follow the

maintenance according to this instruction!

NOTE:

Allow the blades of the hedge trimmer to come to a

complete stop in the position shown. This will allow

clearance for the file between the cutter teeth and the guard

teeth.

Remove and pulling out the battery pack from the product.

Clamp the blade assembly in a vise and file the exposed

cutting surface of each blade tooth with an 8 in. smooth

round file, 1/4 in. or 7/32 in. in diameter. Be sure to retain

the original angle of the tooth when filing.

In order to file both sides of each cutter tooth, you may need

to momentarily run the hedge trimmer until the opposing

side of the cutter teeth are exposed. Do not run the hedge

trimmer while it is locked into the vise. Make sure all tools

for sharpening have been removed before installing the

battery. Remove the battery pack and repeat the sharpening

process for the newly exposed teeth (Fig.10).

CLEANING

Switch the product off, pull out the battery pack from the

product.

Use a small brush to clean the outside of the unit. Do not

use strong detergents. Household cleaners that contain

aromatic oils such as pine and lemon, and solvents such as

kerosene, can damage plastic. Wipe off any moisture with

a soft cloth.

NOTE:

If the cutting blade is blocked by foreign objects during the

operating, stop the product, wait for the cutting blade stops

entirely, remove the foreign objects and clean the cutting

blade.

TRANSPORT

• Clean the product as described above.

• Install the blade cover during the transport.

• Always carry the product by its handle.

• Protect the product from any heavy impact or strong

vibrations which may occur during transportation in

vehicles.

• Secure the product to prevent it from slipping or falling

over,damage or injury.

STORAGE

• Clean the product as described above.

• Store the product and its accessories in a dark, dry, frost-

free, well-ventilated place.

• Always store the product in a place that is inaccessible

to children. The ideal storage temperature is between

50°F(10°C) and 86°F(30°C).

• We recommend using the original package for storage or

covering the product with a suitable cloth or enclosure to

protect it against dust.

NOTE:

To prolong battery life, never store battery pack in a

completely discharged condition. Make sure the battery

pack is charged once per year or when the LED indicator

shows only one light.

DISPOSAL

Waste product should not be disposed of with

household waste. Please recycle where facilities exist.

Check with your local authority or retailer for recycling

advice.

During the operation, the leaves or tree branches may be

cut by the unit, users should clean these objects to protect

environment.

Electrical products should not be discarded with

household products. Used electrical products

must be collected separately and disposed of at

collection points provided for this purpose. Talk

with your local authorities or dealer for advice

on recycling.

EN - 20 WWW.SENIXTOOLS.COM

TROUBLESHOOTING

Suspected malfunctions are often due to causes that the users can x themselves. Therefore, check the product using this

section. In most cases the problem can be solved quickly.

PROBLEM POSSIBLE CAUSE SOLUTION

Product does not start

Battery pack not properly attached Attach properly

Battery pack capacity too low Remove and charge battery pack

Battery pack damaged Check by a specialist electrician

Switch trigger or interlocking switch not set on

ON position Refer to chapter “SWITCHING ON/OFF”

Product does not reach

full power

Battery pack capacity too low Charge battery pack

Air vents are blocked Clean the air vents

Result is unsatisfactory Cutting attachment is worn Replace with a new one

Vibration or noise is

excessive Bolts/nuts are loose Tighten bolts/nuts

Product suddenly stops

Battery pack capacity too low Remove and charge battery pack

Battery too hot Remove battery pack and let it cool

down

La page charge ...

Senix HTX2-M Manuel utilisateur

Senix HTX2-M Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents