La Crosse Technology 30902 Manuel utilisateur

Catégorie
Réveils
Taper
Manuel utilisateur
Page 3 Page 4
Page | 2
0.9” 12 VOLT RED
LED ALARM CLOCK
Model: 30902
DC: 022421
POWER UP
1. Insert the 12V car plug into a 12V car outlet. Optional: Insert one
9 volt battery for backup.
2. 12:00 will flash as an indication to set the time and/or alarm.
TIME SETTING
1. Continuously hold down the TIME button while setting your hour
and minutes.
2. While holding the TIME button, press the HOUR button to set
your hour. Note: The PM indicator will appear when you advance
to PM time.
3. Press the MINUTE button to set your minutes.
4. Release the TIME button when the correct time is shown on the
display.
TIME ALARM
ON HI: Slide the ALARM HI/LO/OFF switch to the HI position to turn
the alarm on at the highest volume (90db). The alarm light indicator will
appear.
ON LO: Slide the ALARM HI/LO/OFF switch to the LO position to turn the
alarm on at a normal volume. The alarm light indicator will appear.
OFF: Slide the ALARM HI/LO/OFF switch to the OFF position to turn the
alarm OFF. The alarm light indicator will disappear.
ALARM ON/OFF & VOLUME
1. Continuously hold down the ALARM button while setting your alarm
time.
2. While holding the ALARM button, press the HOUR button to set your
alarm hour. Note: The PM indicator will appear when you advance to
PM time.
3. Press the MINUTE button to set your alarm minutes.
4. Release the ALARM button when the correct alarm time is shown on the
display.
SNOOZE
• When alarm sounds, press the SNOOZE button to silence alarm for 8
minutes.
• Snooze function can be repeated many times if desired.
• Always purchase the correct size and grade of battery most suitable for
intended use.
• Clean the battery contacts and also those of your clock prior to battery
installation.
• Ensure the battery is installed with correct polarity (+ and -).
• Remove battery from equipment when it is not used for an extended
period of time.
• Promptly remove an expired battery.
CARE & MAINTENANCE
BATTERY BACKUP
• Insert one “9V” battery into the battery compartment on the back of the
clock. The battery will keep the alarm and time settings until the power
is restored.
• The LED display will not light-up but the alarm will sound at the preset
alarm time.
• If there is no battery installed but the power is interrupted, the display
will flash at 12:00 and the time and alarm need to be set again.
Power: 12V power cord. Requires one 9V battery for back-up not included
Dimensions: 1.90”H x 4.55”W x 2.10”D
POWER REQUIREMENTS
HOUR Button
SNOOZE Button
ALARM HI/LO/OFF Switch
MINUTE Button TIME Button ALARM Button
12V CAR PLUG
PM
Light
Indicator
Alarm
Light
Indicator
Time Display
Page 6Page 5 Page 7 Page 8
WARNING: This product can expose you to chemicals including
styrene, which is known to the State of California to cause cancer.
For more information go to: www.P65Warnings.ca.gov
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRICAL SHOCK, DO
NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
Caution: To prevent electrical shock do not use this (polarized) plug with
an extension cord, receptacle, or other outlet unless the blades can be
fully inserted to prevent blade exposure.
ATTENTION: POUR PRÉVENIR LES CHOCS ÉLECTRIQUES NE PAS UTI-
LISER CETTE FICHE POLARISÉE AVEC UN
PROLONGATEUR, UNE PRISE DE COURANT, OU UNE AUTRE SORTIE
DE COURANT SAUF SI LES LAMES PEUVENT ETRE
INSÉRÉES À FOND SANS EN LAISSER AUCUNE PARTIE À
DÉCOUNVERT
SAFETY INSTRUCTIONS
1. Read Instructions - All the safety and operating instructions should be read before the
appliance is operated.
2. Retain Instructions - The safety and operating instructions should be retained for future
reference.
3. Water and Moisture - The appliance should not be used near water - for example, near
a bathub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimmimng
pool and the like.
4. Ventilation - The appliance should be situated so that its location or position does not
interfere with its proper ventilation. For Example, the appliance should not be situated on
a bed, sofa, rug or similar surface that may block the ventilation openings, or place in a
built-in installation such as a bookcase or cabinet that may impede the flow of air through
the ventilation openings
5. Heat - The appliance should be situated away from heat sources such as radiators, heat
registers, stoves, or other appliances (including amplifiers) that produce heat.
6. Power Sources - The appliance should be connected to a power supply only of the type
described in the operating instructions or as marked on the appliance.
7. Grounding or Polarization - Precautions should be taken so that the grounding or
polarization means of an appliance is not defeated.
8. Power - Cord Protection - Power supply cords should be routed so that they are not likely
to be walked on, or pinched by items placed upon or against them, paying particular
attention to cords at plugs, convenience recepticles, and at the point where they exit from
the appliance.
9. Cleaning - The appliance should be cleaned only as recommended by the manufacturer.
10. Object and Liquid Entry - Care should be taken so that objects do not falland liquids are
not spilled into the enclusure through openings.
11. Damage Requiring Service - The appliance should be services by qualified service
personnel when:
A. The power supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance; or
C. The appliance has been exposed to rain; or
D. The appliance does not appear to operate normally or exhibits a marked change in
performance; or
E. The appliance has been dropped, or the enclosure damaged.
12. Servicing - The user should not attempt to service the appliance beyond that described
in the operating instructions. All other servicing should be referred to qualified service
personnel.
Please help in the preservation of the envioronment and return used batteries to an authorized
depot. Remove the battery from the clock if you do not intend to use it for an extended period
of time.
Warning: Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
CAUTION!
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
All rights reserved. This manual may not be reproduced in any form, even in part, or
duplicated or processed using electronic, mechanical or chemical process without the
written permission
of the publisher.
This booklet may contain errors or misprints. The information it contains is regularly
checked and corrections are included in subsequent editions. We disclaim any
responsibility for any technical error or printing error, or their consequences. All
trademarks and patents are recognized.
FCC STATEMENT
Equity provides a 2-year limited warranty on this product from the date of consumer
purchase against defects for material and workmanship. During this period such defects
will be repaired, or the product will be replaced at Equity’s option, without charge. This
warranty does not cover damage caused by misuse or negligence.
ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES
OR FITNESS AND MERCHANTABILITY, ARE LIMITED IN DURATION TO A PERIOD
ENDING TWO YEARS FROM DATE OF PURCHASE.
Some states do not allow limitations on how long an implied warranty lasts so the above
limitation may not apply to you. This warranty gives you specific legal rights and you may
also have other rights which vary from State to State.
If your product is not working properly, please send:
Your product. A letter explaining the problem and $5.00 for postage and handling to:
Equity by La Crosse
Warranty Department
2830 26th St S.
La Crosse, WI 54601
www.lacrossetechnology.com/support
WARRANTY & SUPPORT
Made in China Printed in China
  • Page 1 1
  • Page 2 2

La Crosse Technology 30902 Manuel utilisateur

Catégorie
Réveils
Taper
Manuel utilisateur

dans d''autres langues