°JENN-AIR
DRAWER DISHWASHER
INSTALLATION INSTRUCTIONS
INSTRUCTIONS D'INSTALLATION
LAVE-VAISSELLE A DOUBLE TIROIR
Table of Contents/Table des matieres ............................................................................. 2
iMPORTANT:
Save for local electrical inspector's use.
JnstalJer: Leave installation instructions with the homeowner.
Homeowner: Keep installation instructions for future reference.
iMPORTANT :
_, conserver pour consultation par I'inspecteur local des installations 61ectriques.
Installateur : Remettre les instructions d'installation au propri6taire.
Propri6taire : Conserver les instructions d'installation pour r6f@ence ult@ieure.
W10185132A
TABLEOF CONTENTS
DISHWASHER SAFETY ............................................................................... 2
INSTALLATION REQUIREMENTS ............................................................. 3
Tools and Parts ......................................................................................... 3
Location Requirements ............................................................................. 4
Water Supply Requirements ..................................................................... 5
Electrical Requirements ............................................................................ 5
Drain Requirements .................................................................................. 6
INSTALLATION INSTRUCTIONS ............................................................... 6
Unpack Dish Drawer ................................................................................. 6
Prepare Cabinet Opening ......................................................................... 6
Prepare Dishwasher .................................................................................. 7
Route Electrical Wiring .............................................................................. 8
Route Water Supply Line and Drain Hose ............................................... 9
Connect Water Supply Line and Drain Hoses ....................................... 10
Make Electrical Connection .................................................................... 11
Install Trim Pieces and Level Dishwasher .............................................. 12
Secure Dishwasher ................................................................................. 13
Complete Installation .............................................................................. 14
CUSTOM PANEL INSTALLATION INSTRUCTIONS .............................. 15
Custom Drawer Panel ............................................................................. 15
Preparing Custom Panel ........................................................................ 15
Install Panel Fasteners ............................................................................ 15
Mount the Custom Panel ........................................................................ 16
TABLEDESMATIERES
SI_CURITI_ DU LAVE-VAISSELLE ............................................................ 17
EXIGENCES D'INSTALLATION ................................................................ 18
Outillage et composants ......................................................................... 18
Exigences d'emplacement ..................................................................... 19
Sp6cifications de I'alimentation en eau.................................................. 19
Specifications electriques ....................................................................... 20
Evacuation de I'eau de lavage--Crit6res &respecter ............................ 20
INSTRUCTIONS D'INSTALLATION ......................................................... 21
Deballage du lave-vaisselle .................................................................... 21
Pr6paration de I'espace d'installation entre les placards ...................... 21
Pr6paration du lave-vaisselle .................................................................. 22
Installation du c&blage electrique ........................................................... 23
Installation du tuyau d'arrivee d'eau et du tuyau d'evacuation ............. 23
Raccordement du tuyau d'arriv6e d'eau et du tuyau d'evacuation ...... 24
Raccordement du circuit electrique ....................................................... 26
Installation des pieces de garniture; etablissement de I'aplomb
du lave-vaisselle ..................................................................................... 27
Arrimage de lave-vaisselle ...................................................................... 28
Achever I'installation ............................................................................... 29
INSTRUCTIONS D'INSTALLATION DU PANNEAU DI_CORATIF ......... 30
Panneau decoratif de tiroirs personnalises ............................................ 30
Pr6paration de panneau personnalise ................................................... 30
Installation des dispositifs de fixation de panneau ................................ 30
Montage du panneau decoratif .............................................................. 31
DISHWASHERSAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
2
iMPORTANT SAFETY iNSTRUCTiONS
WARNING: When using the dishwasher, follow basic precautions, including the following:
m Read all instructions before using the dishwasher.
m Use the dishwasher only for its intended function.
m Use only detergents or rinse agents recommended for use
in a dishwasher, and keep them out of the reach of children.
m When loading items to be washed:
1) Locate sharp items so that they are not likely to damage
the door seal; and
2) Load sharp knives with the handles up to reduce the risk
of cut-type injuries.
m Do not wash plastic items unless they are marked
"dishwasher safe" or the equivalent. For plastic items not so
marked, check the manufacturer's recommendations.
m Do not touch the heating element during or immediately
after use.
m Do not operate the dishwasher unless all enclosure panels
are properly in place.
m Do not tamper with controls.
m Do not abuse, sit on, or stand on the door, lid, or dish racks
of the dishwasher.
m To reduce the risk of injury, do not allow children to play in
or on the dishwasher.
m Under certain conditions, hydrogen gas may be produced in
a hot water system that has not been used for two weeks or
more. HYDROGEN GAS IS EXPLOSIVE. If the hot water
system has not been used for such a period, before using
the dishwasher turn on all hot water faucets and let the
water flow from each for several minutes. This will release
any accumulated hydrogen gas. As the gas is flammable,
do not smoke or use an open flame during this time.
m Remove the door or lid to the washing compartment
when removing an old dishwasher from service or
discarding it.
SAVE THESE iNSTRUCTiONS
Tip Over Hazard
Do not open dishwasher drawer until inside cabinet opening.
Doing so can result in death or serious injury.
You need to:
• Slowly open dishwasher drawer while someone grasps the
rear of the dishwasher. Remove shipping materials. Close
dishwasher drawer. Latch the dishwasher drawer shut.
• Observe all governing codes and ordinances.
• Install this dishwasher as specified in these instructions.
• Have everything you need to properly install dishwasher.
• Contact a qualified installer to ensure that dishwasher is
installed to meet all electrical and plumbing national and local
codes and ordinances.
INSTALLATIONREQUIREMENTS
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools Needed
• Pliers
• Phillips screwdriver
• Flat-blade screwdriver
• ¾e" and 1¼,,nut drivers or
hex sockets
• Measuring tape or ruler
• 11/2"hole saw bit
• 10" adjustable wrench
• Utility knife
• Level
• Cordless drill
• 1/8"drill bit
• Security T-20 TORX®t
driver (if installing custom
front panel)
PaNs Needed
1-®TORX is a registered trademark of Acument Intellectual Properties, LLC
E
A. 72" (182.9 cm) flexible water
supply fine
B. Zip tie
C. Appropriate sized UL-fisted wire
connectors (2)
D
D. Handle (if installing
custom front panel)
E. Custom panel (if
installing custom front
panel)
Parts Supplied
Check that all parts are included.
G
K
C
Product Dimensions
333/4''
(85.7 cm)
11/2 ''
(48.9 cm) (3.75 cm)
A. _" UL-listed strain relief
B. 1.25" hose clamp
C. Mounting bracket screws (8)
D. Unit mounting screws (4)
E. Ydrain connector
F. Mounting brackets (4)
G. Drain connector spring
clamps (2)
H. Trim strips (2)
I. Toe kick brackets (2)
J. Toe kick bracket screws (2)
K. Toe kick trim
L. Panel fasteners (on some
models) (2)
M. TORX_tscrews (on some
models) (10)
OS eme
IMPORTANT: Observe all governing codes and ordinances.
Failure to meet codes and ordinances could lead to fire or
electrical shock.
Proper installation is your responsibility.
• Contact a qualified installer to ensure that the dishwasher is
installed to meet all electrical and plumbing national and local
codes and ordinances.
• Install the dishwasher as specified in these instructions.
• Have everything you need to properly install dishwasher.
• Avoid damage from freezing to dishwasher and water lines
leading to dishwasher. Damage from freezing is not covered
by the warranty.
• This dishwasher is manufactured for indoor use only.
• Install and level dishwasher on a floor that will hold the weight,
and in an area suitable for its size and use.
Installation Clearances
Cutout Dimensions
23W'
"(59.7 cm)"
Preferred Utililty Area
A. Left-hand or right-hand drain and water connection route
B. Left-hand or right-hand electric connection route
NOTES:
• All holes should be drilled at 11/2"(3.8 cm) diameter.
• If the cabinet is wood, sand the hole until smooth. If the
cabinet is metal, cover the hole with a grommet (Part
Number 302797).
• For power supply cord connection, a mating, grounded
3 prong outlet is required in a cabinet next to the dishwasher
opening.
• A hot water line with 20-120 psi (138-862 kPa) water pressure.
• 120°F (49°C) water temperature at dishwasher.
• Flexible stainless steel braided fill line (1/2"minimum plastic
tubing is not recommended).
E emen s
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
GROUNDING iNSTRUCTiONS
For a grounded, cord-connected dishwasher:
The dishwasher must be grounded. In the event of a
malfunction or breakdown, grounding will reduce the
risk of electric shock by providing a path of least
resistance for electric current. The dishwasher is
equipped with a cord having an equipment-grounding
conductor and a grounding plug. The plug must be
plugged into an appropriate outlet that is installed and
grounded in accordance with all local codes and
ordinances.
WARNING: Improper connection of the
equipment-grounding conductor can result in a risk of
electric shock. Check with a qualified electrician or
service representative if you are in doubt whether the
dishwasher is properly grounded. Do not modify the
plug provided with the dishwasher; if it will not fit the
outlet, have a proper outlet installed by a qualified
electrician.
For a permanently connected dishwasher:
The dishwasher must be connected to a grounded
metal, permanent wiring system, or an equipment-
grounding conductor must be run with the circuit
conductors and connected to the equipment-
grounding terminal or lead on the dishwasher.
SAVE THESE iNSTRUCTiONS
It is the customer's responsibility to:
• Contact a qualified electrician.
• Ensure that the electrical installation is adequate and in
conformance with all national and local codes and ordinances.
Requirements:
• 120-volt, 60 Hz, AC-only, 15- or 20-amp fused electrical
supply
• Copper wire only, 2 wire with ground
Recommended:
• Time-delay fuse or circuit breaker
• Separate circuit
Direct Wire Connection
• Use flexible, armored or nonmetalic sheathed, copper wire
with grounding wire that meets the wiring requirements for
your home and local codes and ordinances.
• Use strain relief method provided with house wiring junction
box or install a UL-listed/CSA-approved clamp connector to
the house wiring junction box. If using conduit, use a
UL-listed/CSA-approved conduit connector.
Power Supply Cord Connection
Use Power Supply Cord Kit (Part Number 4317824) marked for
use with dishwashers. Kit contents include:
• Voltex, Inc., UL-listed 16-gauge 3-wire power supply cord with
3 prong grounding plug
• Neer C-500 7/8"strain relief
• 3 wire connectors
• Grommet (Part Number 302797)
Follow the kit instructions for installing the power supply cord.
NOTE: Power supply cord must plug into a mating, grounded
3 prong, outlet, located in the cabinet next to the dishwasher
opening. Outlet must meet all local codes and ordinances.
IMPORTANT:Ifyouplantoinstallagarbagedisposal,an
additionalseparate120-volt,60Hz,AC-only,15-or20-ampfused
electricalsupplyisrequired.
• Useadrainairgapifthedrainhoseisconnectedtohouse
plumbinglowerthan20"(50.8cm)abovethesubfloororfloor.
Drain Air Gap
• Use the new drain hose supplied with your dishwasher. If this _I |
is not long enough, use a new drain hose with maximum
length of 12 ft (3.7 m) that meets all current AHAM/IAPMO test
standards, is resistant to heat and detergent, and fits the
1" (2.5 cm) drain connector of the dishwasher.
Connect drain hose to waste tee or disposer inlet above drain
trap in house plumbing and 20" (50.8 cm) minimum above the
floor. It is recommended that the drain hose either be looped
up and securely fastened to the underside of the counter, or
be connected to an air gap.
Use W' (1.3 cm) minimum I.D. drain line fittings.
INSTALLATIONINSTRUCTIONS
Electrical Shock Hazard
Disconnect electrical power at the fuse box or circuit
breaker box before installing dishwasher.
Failure to do so can result in death or electrical shock.
1. Disconnect power.
2. Turn off water supply.
Excessive Weight Hazard
Use two or more people to move and install
dishwasher.
Failure to do so can result in back or other injury.
2. Drill 1V2"(3.8 cm) diameter holes for drain and water hoses
and electrical wiring as shown. Holes should be placed
1/2'(1.3 cm) from back wall.
3.
A. Choose left-hand or fight-hand drain and water hose route.
B. Choose left-hand or fight-hand electric wire route.
Install mounting brackets 17" (43.2 cm)from floor using
screws provided. If needed, drill V8"pilot holes in cabinet.
1. Read valuable information on exterior of shipping box before
opening.
2. Remove shipping materials, tape and film from the
dishwasher. Remove parts package from inside the
dishwasher.
1=
Ccsb ne "C ng
To ensure minimum clearance dimensions exist:
• Measure the distance from the cabinet countertop to the
floor and ensure 333/4"(85.7 cm) minimum height.
• Measure the distance from the front of the cabinet to the
back wall and ensure 24" (61 cm) minimum depth.
• Measure the distance from the left-hand side to the right-
hand side of opening and ensure 23V2"(59.7 cm) minimum
width.
0
4
17"
(43.2 cm)
4. Decide which dishwasher-to-counter attachment method will
be used.
6
Option 1: Solid surface countertop installation
• Install second set of mounting brackets 331/2'' (85 cm) from
floor. If needed, drill 1/8"pilot holes in cabinet.
P_s?©ctFe L/>? WC_;:;¢_;;£
Tip Over Hazard
Do not open dishwasher drawer until inside cabinet
opening.
Doing so can result in death or serious injury.
Option 2: Wood countertop installation
• Prepare dishwasher by folding over tabs located on the
top front as shown.
Excessive Weight Hazard
Use two or more people to move and install
dishwasher.
Failure to do so can result in back or other injury.
1. Measure cabinet opening height from floor to bottom of
countertop.
2.
H
Place corner packaging on the floor and place dishwasher on
its back.
3. Adjustlevelinglegsbasedonthecabinetopening
measurementandthechartbelow.
\
/
/
/
j
IX
v
H
33 _" (86cm)
34" (86.3 cm)
34 _" (86.7cm)
34 _" (870m)
34%" (87.3 cm)
:X
:0"
: _" (0.3 cm)
:¼" (0.6 cm)
:%" (1 cm)
:V2" (1.3 cm)
H
34½" (87.6cm)
34 _" (87.9 cm)
34 _" (88.3 cm)
34 _" (88.6 cm)
35" (88.9 cm)
4. Place dishwasher in upright position.
:X
:_" (1.6 cm)
:%" (1.9 cm)
:_" (2.2 cm)
:1" (2.5 cm)
:1 _" (2.9 cm)
B_C_ ;@ .........._.. C :.,s_J__ _._s_;_
Electrical Shock Hazard
Disconnect electrical power at the fuse box or circuit
breaker box before installing dishwasher.
Failure to do so can result in death or electrical shock.
Follow all national and local codes and ordinances for completing
electrical supply to cabinet.
Option 1: Right-hand side utility route
Route wire through 1V2" (3.81 cm) hole located
8" (20.32 cm) above the floor.
After routing the electrical wire through the right-hand hole, attach
the wire to back left-hand side of cabinet wall 8" (20.32 cm) above
the floor. Then continue routing the wire along the left-hand side of
cabinet opening to the front of the opening.
Option 2: Left-hand side utilityroute
Route wire through 1V2"(3.81 cm) hole located 8"
(20.32 cm) above the floor.
After routing the electrical wire through the left-hand hole,
continue routing the wire along the left-hand side of cabinet to the
front of the opening.
8
1. Oonnect water supply lineto water valve ondishwasher.
Option 2: Left-hand side utility access
• For left-hand routing, remove drain hoses from the clips in
the rear bracket as shown.
2. Route water supply line and drain hoses based on your
cabinet requirements.
Option 1: Right-hand side utility access
• For right-hand routing, water supply and drain hoses are
shipped in the correct position. Place the water supply line
in the clip as shown.
• Route water supply line and drain hoses into the cabinet.
• Slide dishwasher partway into the cabinet opening. Allow
for access to the electrical terminal box.
1=
Connect water supply line to the water valve under the sink.
Option 1:Waste disposer no drain air gap
A
/
2=
3.
4.
A. Hot water supply
Slide clamps onto drain hoses (Figure A). Do not cut drain
hoses.
Push hoses into Y drain connector until fully seated (Figure B).
Several "clicks" will be heard.
Slide clamps into position (figures C and D).
A B
A. For new construction, remove disposer plug.
B. Connect drain connector to waste disposer.
C. Tighten clamp.
Option 2: No waste disposer and drain air gap
C D
5. Connect the drain hose using one of the following options:
A. Drain hose connector
B. Drain air gap
C. Waste
S ..........
C
A. Drain hose connector
B. Drain air gap
C. Waste
10
C
6=
A. Drain hose connector
B. Cut drain connector
C. Waste
NOTE: Attach the drain hose connector to the water waste
line using the supplied hose clamp.
Turn on water and check for leaks.
Electrical Shock Hazard
Disconnect electrical power at the fuse box or circuit
breaker box before installing dishwasher.
Failure to do so can result in death or electrical shock.
1. Remove screw securing the electrical box cover. Remove
cover.
2. Route electrical wires through strain relief and secure to
electrical plate.
3. Tighten the conduit connector and strain relief screws.
Electrical Shock Hazard
Electrically ground dishwasher.
Connect ground wire to green ground connector in
terminal box.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
4. Connect wires as follows using twist-on connectors sized to
connect direct wire to 16 gauge dishwasher wire.
Power supply wire: Terminal box wire:
white white
black black
ground wire _ _ ground connector
11
5. Attach ground wire to the green ground screw. 3. Lift drawer off slide rails. Place drawer off to the left on
covering. Slide rails into dishwasher.
6.
\
\
\
B
A. Attach ground wire to green screw.
B. Attach white and black wires.
Reinstall electric box cover with all wires contained inside the
terminal box.
4.
5.
Slide the dishwasher into position in the cabinet opening.
Check to ensure that the drain hose and electrical wiring are
not kinked.
Check left to right level by placing the level on the top of the
drawer. Check front to back level by placing level on the slide
rails.
6. Adjust legs with a 3/ld' socket wrench to level the dishwasher.
Insicll YAm Ii®ces c_...........= _'_[sB sl-_et_
1. Open bottom drawer.
2. Push in clips and slide rails back 5" (12.7 cm).
\
A. Adjust legs.
12
7. 10. Attach the toe kick bracket on the opposite side.Rest the trim strip on the floor and mark the trim at the top of
the frame flange height. Pick the closest groove to the mark. If
the mark is between 2 grooves, choose the groove that makes
the trim strip shorter. On a covered surface, cut the trim strip
at the selected groove.
11. Place the flexible side trim strips on both sides as shown.
8. Attach the toe kick bracket to the frame.
9. Place the trim strip into the toe kick bracket.
1.
Secue
Remove the top drawer (same procedure as followed to
remove bottom drawer) and set the drawer on the bottom
drawer separated with the corner packaging.
13
2.
Attach dishwasher to the lower cabinet mounting bracket
(installed earlier).
A
\
1. Pull top drawer slide rails out and set top drawer on slide rails.
A.Attach dishwasherto lower cabinet mounting bracket.
3. Attach dishwasher to upper cabinet mounting brackets.
Option 1: Solid surface countertop
Attach dishwasher to the side cabinet mounting brackets
(installed earlier).
2. Pull slide rails forward until they snap into position.
3. Push top drawer in and repeat above steps for bottom drawer.
4. In the cabinet under the sink, coil excess drain hose and wrap
with a zip tie.
A.Attach dishwasher to side cabinet mounting brackets.
Option 2: Wood countertop
Attach the dishwasher to the countertop using the folded over
mounting tabs located on the top of the dishwasher.
A
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
5. Plug in dishwasher or reconnect the power.
A. Attach dishwasher to countertop using folded over mounting tabs.
14
6. Select the Rinse Only cycle and press START/RESUME. Allow
the dishwasher to fill, rinse and drain. Check for leaks. If leaks
are found, secure the connection and repeat this step.
If you need Assistance or Service:
Please reference the "Assistance or Service" section of the User
Instructions or contact the dealer from whom you purchased your
dishwasher.
CUSTOM PANELINSTALLATIONINSTRUCTIONS
Custom _u'+_s_5_+_P_c__'_ss,
If you plan to install a custom wood panel, you will need to create
the panel yourself or consult a qualified cabinetmaker or
carpenter. See dimension drawings for panel specifications.
IMPORTANT:
• The thickness of the custom panel must be 1/2"(1.3 cm) to 3/4"
(1.9 cm).
• Do not exceed the height dimension for the custom panel. A
panel that exceeds the height dimension may damage the
drawer dishwasher, cabinets or countertop.
• The width of the custom panel may vary according to the
width of the cabinet opening.
Custom Panel Dimensions
Upper Drawer Panel
3 ii
¼
(1,9 cm)/
237A6 ''
(59.5 cm)
t
16V4"
(41.3 cm)
/
Lower Drawer Panel
3 ii
¼
(1.9ore!!
237/16''
< (59.5 cm) _"
Hardware Installation
Center the hardware (left to right) onto the custom panel. When
installing the hardware, be sure that the mounting screws are flush
with the back of the custom panel.
1.
2.
Lay the custom panel face down on a clean, soft work
surface.
Using a pencil, mark the centerpoints for the 2 panel fastener
pilot holes and 6 pilot holes needed for the panel.
A
(28.5 cm)
81/8"
cm
A. Center line
B. Panel fastener pilot holes (2)
C. Pilot holes (6)
3. Mark the centerpoints for the 2 panel fastener pilot holes and
4 pilot holes need for the lower panel.
I
I
A. Center line
B. Panel fastener pilot holes (2)
C. Pilot holes (4)
z llA ,, _
(3.8 cm) l
10Y2"
(26.7 ci)
15
4. Using a 1/8"drill, drill each hole 3/8"(1 cm) deep. Custom Decorative Panel
3/8"(1cra)
IMPORTANT: To avoid drilling through to the front of the
custom panel, do not drill deeper than 3/8"(1 cm).
n@c neti d ene s
1. Remove the 2 panel fasteners from the face of the inner door
of the drawer.
! ................................
2. Screw the 2 panel fasteners into the panel fastener pilot holes
of the custom panel.
Custom Decorative Panel Only
1. Remove the tape from the green ground wire on the custom
decorative panel. The end of the green ground wire is factory-
attached to the custom decorative panel.
2. Attach the ring connector end of the green ground wire on the
custom decorative panel to the ring connector and ground
screw on the dishwasher drawer intermediate panel.
(
A. Green ground wire
B. Ground screw
Custom Decorative Panel or Custom Wood Panel
1. Mount the custom panel to the drawer by aligning the panel
fasteners to the 2 keyhole slots and insert the panel.
Custom Wood Panel
2. To secure the custom panel onto the drawer, push the custom
panel down until the top of the custom panel is flush with the
top of the control panel.
3. Using the screws provided, secure the custom panel to the
inner door by screwing through the inner door and into the 1/8"
(3.2 mm) pilot holes.
16
SECURITEDU LAVE-VAISSELLE
Votre securite et celle des autres est tres importante.
Nous donnons de nombreux messages de s_curit_ importants dans ce manuel et sur votre appareil m_nager. Assurez-vous de
toujours lire tousles messages de s_curit_ et de vous y conformer.
Voici le symbole d'alerte de s_curit&
Ce symbole d'alerte de s_curit_ vous signale les dangers potentiels de d_c_s et de blessures graves & vous
et &d'autres.
Tous les messages de s_curit_ suivront le symbole d'alerte de s_curit_ et le mot "DANGER" ou
"AVERTISSEMENT". Ces mots signifient •
Risque possible de d_cbs ou de blessure grave si vous ne
suivez pas imm_diatement les instructions.
Risque possible de d_cbs ou de blessure grave si vous
ne suivez pas les instructions.
Tous les messages de s_curit_ vous diront quel est le danger potentiel et vous disent comment r_duire le risque de blessure et
ce qui peut se produire en cas de non-respect des instructions.
IMPORTANTES INSTRUCTIONS DE SI_CURITI_
AVERTISSEMENT : Lors de I'utilisation du lave-vaisselle, suivre les precautions el6mentaires dont les suivantes •
m Lire la totalite des instructions avant d'utiliser le
lave-vaisselle.
m N'utiliser le lave-vaisselle que pour laver la vaisselle.
[] Utiliser les detersifs ou agents de rin_age recommandes
pour lave-vaisselle et les garder hors de la portee des
enfants.
[] Lorsque vous chargez le lave-vaisselle :
1) Placer les objets coupants de fagon qu'ils ne puissent
endommager le joint de la porte; et
2) Placer les couteaux le manche vers le haut de fa(;on & ne
pas vous couper.
[] Ne pas laver d'articles en plastique & moins qu'ils ne soient
marques "Peut aller au lave-vaisselle" ou I'equivalent. Si
I'article ne porte aucune indication, verifier aupres du
fabricant.
[] Ne pas toucher I'el6ment chauffant pendant le
fonctionnement ou immediatement apres.
[] Ne pas faire fonctionner le lave-vaisselle si tousles
panneaux de I'enceinte ne sont pas en place.
[] Ne pas jouer avec les commandes.
[] Ne pas abuser, vous asseoir ni monter sur la porte,
le couvercle ou les paniers du lave-vaisselle.
[] Pour eviter tout risque d'accident, ne pas laisser les
enfants jouer dans ou sur le lave-vaisselle.
[] Sous certaines conditions, de I'hydrogene peut se former
dans un reseau d'eau chaude inutilise depuis deux
semaines ou plus. L'HYDROG#NE EST UN GAZ
EXPLOSIBLE. Si le systeme d'eau chaude n'a pas et6
utilise depuis un certain temps, laisser couler I'eau chaude
des robinets pendant quelques minutes avant de faire
fonctionner le lave-vaisselle. Cette mesure permettra &
I'hydrogene de s'evaporer. Ce gaz etant inflammable, ne
pas fumer ni utiliser de flamme nue pendant cette periode.
[] Enlever la porte ou le couvercle du compartiment de lavage
Iorsque vous remplacez ou mettez au rebut un vieux
lave-vaisselle.
CONSERVEZ CES INSTRUCTIONS
Risque de basculement
Ne pas ouvrir le tiroir du lave-vaisselle jusqu'_ ce qu'il soit plac_ _ I'int_rieur de I'ouverture
du placard.
Le non=respect de ces instructions peut causer un d_c_s ou des blessures graves.
17
Operations _ ex_cuter :
• Ouvrir lentement le tiroir du lave-vaisselle tandis qu'une autre
personne saisit/retient I'arriere du lave-vaisselle. Retirer les
materiaux d'emballage. Fermer le tiroir du lave-vaisselle.
Verrouiller le tiroir du lave-vaisselle.
• Respecter les prescriptions de tousles codes et reglements
en vigueur.
Installer le lave-vaisselle conformement aux presentes
instructions.
Veiller & disposer de tout ce qui est necessaire pour
I'installation correcte du lave-vaisselle.
Contacter un installateur qualifie pour garantir que
I'installation du lave-vaisselle soit executee conformement
aux prescriptions de tous les codes et reglements nationaux
et Iocaux regissant les installations electriques et de
plomberie en vigueur.
EXIGENCESD'INSTALLATION
Rassembler les outils et pieces necessaires avant de commencer
I'installation. Lire et suivre les instructions fournies avec les outils
indiques ici.
Outillage n_cessaire
• Pince
• Tournevis Philips
• Tournevis & lame plate
• Douilles hexagonales/
tourne-ecrou--3Ad ' et 1¼.
• Metre ruban ou regle
• Scie a trou--11/2"
• Cle & molette--10"
• Couteau utilitaire
• Niveau
• Perceuse sans fil
• Foret de--V8"
• Tournevis TORX®tT-20
(pour I'installation de
panneaux de fagade
personnalises)
Pi_ces fournies
Verifier la presence de toutes les pieces.
Composants n_cessaires
C
G
H ..............
A. Tuyau d'arriv_e d'eau flexible
72" (182,9 cm)
B.Attache en plastique
C. Connecteurs de ills de taille
appropri_e--
homologation UL (2)
D
E
D. Pieces de quincaillerie (pour
/'installation de panneaux de
fagade personnafis_s)
E.Panneau d_coratif (pour
I'installation de panneaux de
fagade personnafis_s)
A. Serre-c#ble _"--
homologation UL
B.Bride de tuyau 1,25"
C. Vis de montage des brides (8)
D. Vis de fixation de I'appareil (4)
E. Raccord Ypour tuyau
d '_vacua tion
F. Brides de montage (4)
G. Brides de tuyau pour tuyau
d'_vacuation (2)
H. Cornieres de garniture (2)
I.Brides pour corniere de
plinthe (2)
J. Vis--fixation des brides de la
corniere de plinthe (2)
K. Corniere de plinthe
L. Vis de fixation de panneau
(certains modeles) (2)
M. Vis TORX _t (certains
modeles) (10)
t®TORX est une marque deposee de Acument Intellectual Properties,
18
IMPORTANT : Observer les dispositions de tous les codes et
r@glements en vigueur. Le non-respect de ces codes et
r@glements pourrait entrainer un incendie ou un choc @ctrique.
C'est a I'utilisateur du produit qu'incombe la responsabilit@ de
r@aliserune installation correcte.
Contacter un installateur qualifie pour garantir que
I'installation du lave-vaisselle soit ex@utee conformement
aux prescriptions de tousles codes Iocaux et nationaux en
vigueur regissant les installations d'electricit6 et de plomberie.
Realiser I'installation du lave-vaisselle tel que sp@ifie dans
ces instructions.
Veiller &disposer de tousles outils et composants n@essaires
pour I'installation du lave-vaisselle.
Proteger le lave-vaisselle et les canalisations d'eau qui
I'alimentent contre les dommages imputables au gel. La
garantie ne couvre pas les dommages imputables au gel.
Ce lave-vaisselle est con£;u et fabriqu6 uniquement pour une
utilisation & I'interieur.
Installer melave-vaisselle d'aplomb en un endroit approprie sur
un sol capable d'en soutenir le poids compte tenu de sa taille
et de son utilisation.
Dimensions du produit
333/4"
(85,7 cm)
11/2"
(3,75 cm)
Distances de d_gagement & respecter
Dimensions de I'espace d'installation
231/2"
(59,7 cm)
33Y8"
Emplacements pr_f_rentiels pour le passage des tuyaux et
du c&ble
A. Choisir la position d'installation des tuyaux d'eau et d'_vacuation--
gauche ou _ droite.
B. Choisir la position d'installation du c_blage dectrique-- _ gauche ou
droite.
REMARQUES :
• Diam_tre de 11/2"(3,8 cm) pour tousles trous.
• Si le placard est en bois, poncer le trou jusqu'& ce qu'il soit
lisse. Si le placard est en metal, recouvrir le trou avec un oeillet
(non fourni).
• On doit disposer d'une prise de configuration correspondante
&trois alv@les et reli@ & la terre dans un placard qui se
trouve pros de I'ouverture du lave-vaisselle.
• Canalisation d'eau chaude avec pression de 20-120 Ib/po2
(138-862 kPa).
• Admission dans le lave-vaisselle d'eau & temperature de
120°F (49°0).
• Raccordement entre I'appareil et la canalisation d'eau & I'aide
d'un conduit flexible &gaine tress@ (on d@onseille I'emploi
de tube de plastique--diam_tre minimum 1/2").
19
Risque de choc _lectrique
Brancher sur une prise a 3 aIv_oles reli_e a la terre.
Ne pas enlever la broche de liaison a la terre.
Ne pas utiliser un adaptateur.
Ne pas utiliser un cable de rallonge.
Le non=respect de ces instructions peut causer
un d_c_s, un incendie ou un choc _lectrique.
iNSTRUCTiONS DE MISE A LA TERRE
• Pour un lave=vaisselle reli_ & la terre, branch_ avec
un cordon :
Le lave-vaisselle doit _tre relie & la terre. En cas d'un
mauvais fonctionnement ou d'une panne, la mise & terre
reduira le risque d'un choc electrique en fournissant le
moins de resistance pour le courant electrique. Le lave-
vaisselle est equip6 d'un cordon avec un conducteur
pour relier les appareils a la terre. La fiche doit _tre
branchee sur une prise appropriee, installee et reliee a la
terre conformement aux codes et reglements Iocaux.
AVERTiSSEMENT : La connexion incorrecte
du conducteur pour relier les appareils & la terre peut
causer le risque de choc electrique. Verifier avec un
electricien competent ou un representant de service si
vous avez des doutes si le lave-vaisselle est
correctement relie & la terre. Ne pas modifier la fiche
fournie avec le lave-vaisselle; si elle n'entre pas dans la
prise, faire installer une prise appropriee par un
electricien competent.
• Pour un lave=vaisselle branch_ en permanence :
Le lave-vaisselle doit _tre branche a un systeme
d'installation electrique permanent en metal relie & la
terre, ou un conducteur pour relier les appareils a la terre
doit _tre relie avec les conducteurs du circuit et branche
une borne pour relier les appareils a la terre ou au
cordon d'alimentation electrique avec le lave-vaisselle.
CONSERVEZ CES INSTRUCTIONS
Contacter un electricien qualifi&
Verifier que le circuit d'alimentation disponible est adequat et
conforme aux prescriptions de tousles codes et reglements
nationaux et Iocaux en vigueur.
Caract_ristiques de la source d'_lectricit_ n_cessaire :
• 120 V,60 Hz, CA, fusible de 15 ou 20 A.
• Conducteurs de cuivre seulement.
Nous reoommandons :
• Fusible temporise ou disjoncteur.
20
• Alimentation par un circuit distinct.
Raccordement direct du lave-vaisselle
• Utiliser un c&ble flexible & conducteurs de cuivre, avec gaine
metallique ou non metallique et conducteur de raccordement
la terre, qui satisfait aux exigences des codes et reglements
Iocaux en vigueur.
• Utiliser le serre-c&ble fourni pour le raccordement au boitier
de raccordement de la maison, ou installer un serre-c&ble
(homologation UL/CSA) sur le boitier de raccordement de la
maison. Dans le cas de I'utilisation de conduit, utiliser un
connecteur de conduit (homologation UL/CSA).
Branchement de I'appareil & I'aide d'un cordon
d'alimentation
• Utiliser le cordon d'alimentation congu (piece n° 4317824)
pour I'utilisation avec un lave-vaisselle; cet ensemble
comporte :
• Cordon d'alimentation a 3 conducteurs de calibre 16, avec
fiche de branchement &3 broches, pour liaison & la terre -
homologation UL (Voltex, Inc.).
• Serre-c&ble 7/8"(Neer, C-500)
• 3 connecteurs de fils
• Passe-fil (piece n° 302797)
Pour I'installation du cordon d'alimentation, executer les
instructions fournies avec I'ensemble.
REMARQUE : La fiche du cordon d'alimentation doit _tre
branchee sur une prise de courant de m_me configuration, &
3 alveoles, reliee & la terre, installee dans le placard & c6te de
I'espace d'installation du lave-vaisselle. La prise de courant doit
satisfaire les prescriptions de tousles codes et reglements Iocaux
en vigueur.
IMPORTANT : Si on envisage I'installation d'un broyeur
dechets, un circuit electrique additionnel est egalement
necessaire--120 V, 60 H, CA, fusible de 15 ou 20 A seulement.
• Utiliser le tuyau d'evacuation neuf fourni avec I'appareil. Si la
Iongueur de ce tuyau n'est pas suffisante, utiliser un autre
tuyau d'evacuation avec Iongueur maximale de 12 pi (3,7 m),
conforme aux prescriptions de la norme AHAM/IAPMO,
resistant & la chaleur et au detergent, et compatible avec le
raccord de connexion de 1" (2,5 cm) du lave-vaisselle.
• Connecter le tuyau d'evacuation sur un raccord T ou &I'entree
du broyeur a dechets au-dessus du siphon du circuit
d'evacuation de la maison et &au moins 20" (50,8 cm) au-
dessus du plancher. On recommande de former une boucle
avec le tuyau d'evacuation (arrimage avec une attache de
plastique sous le plan de travail), ou de connecter le tuyau
d'evacuation a un brise-vide.
• Si le tuyau d'evacuation doit _tre raccorde au circuit
d'evacuation de la maison a moins de 20" (50,8 cm) au-
dessus du sous-sol ou du sol, utiliser un brise-vide.
Brise-vide
Utiliser des raccords de diametre interne de W' (1,3 cm) ou
plus.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
Jenn-Air JDD4000AWX2 Guide d'installation
- Taper
- Guide d'installation
- Ce manuel convient également à
dans d''autres langues
Documents connexes
Autres documents
-
KitchenAid KUDD03DTSS2 Guide d'installation
-
-
-
IKEA IUD9750WS0 Guide d'installation
-
KitchenAid KUDD03STBL Manuel utilisateur
-
-
KitchenAid KUDD03STWH2 Guide d'installation
-
KitchenAid KUDD03DTPA10 Guide d'installation
-
-