Ricoh D5520 Read this first

Português (Brasil)

Español

Français

Deutsch

English

Leia isto primeiro

Leer antes de empezar

À lire avant de commencer

Bitte zuerst lesen

Read This First

Read this manual carefully before you use this machine and keep

it handy for future reference. For safe and correct use, be sure to

read the Safety Information in this manual before using the

machine.

For information not in the printed manual,

refer to the HTML/PDF ﬁles on the website.

Connection

Component Names and Functions

Installing the Machine (Installed by a

Contractor)

Information for This Machine

Safety Information for this Machine

Read This First

English

TABLE OF CONTENTS

Disclaimer............................................................................................................................................................3

About Operating Instructions.............................................................................................................................4

1. Safety Information for this Machine

Safety Symbols for This Machine...................................................................................................................... 5

Safety Information...............................................................................................................................................6

Safety During Operation............................................................................................................................... 6

Safety Precautions to Be Followed................................................................................................................6

Safety Labels of This Machine.........................................................................................................................10

Positions of WARNING and CAUTION labels.........................................................................................10

Symbols for Earth and Power Switch......................................................................................................... 10

Important Safety Instructions........................................................................................................................... 11

Notes on the LCD Panel of the Machine........................................................................................................12

2. Information for This Machine

Laws and Regulations...................................................................................................................................... 13

Warning on Class A Product...................................................................................................................... 13

CE Marking Traceability Information (For EU Countries Only)............................................................... 13

User Information for Wireless Network (For EU Countries Only)............................................................13

Overseas Affiliates and Noise Emission Information................................................................................ 14

User Information on Electrical and Electronic Equipment.........................................................................14

Note for the Battery and/or Accumulator Symbol (For EU countries only)............................................15

Notes to USA Users of FCC Requirements................................................................................................ 15

Notes to users in the United States of America..........................................................................................16

Notes to Canadian Users of Wireless Devices......................................................................................... 16

Notes to Users in the State of California (Notes to Users in USA)...........................................................17

Notes for Contractors (in Norway)............................................................................................................ 17

3. Installing the Machine (Installed by a Contractor)

Installing the Machine (Installed by a Contractor)........................................................................................19

Installation Precautions.................................................................................................................................... 20

Wall Mounting Precautions........................................................................................................................ 20

Environmental Specifications...........................................................................................................................22

Installation Space Requirements..................................................................................................................... 23

When Installing the Machine by Mounting the Main Unit on a Wall.....................................................23

Mounting the Pen Tray.....................................................................................................................................25

1

4. Component Names and Functions

Input/Output Terminals................................................................................................................................... 27

5. Connection

Connecting the Touch Module........................................................................................................................29

Connecting the Bluetooth Adapter................................................................................................................. 30

Connecting Power............................................................................................................................................31

2

Disclaimer

To the maximum extent permitted by applicable laws, in no event will the manufacturer be liable for any

damages whatsoever arising out of failures of this machine, losses of the registered data, or the use or

non-use of this product and operation manuals provided with it.

Make sure that you always copy or have backups of the data registered in this machine. Documents or

data might be erased due to your operational errors or malfunctions of the machine.

3

About Operating Instructions

Operating Instructions explains how to operate and troubleshoot the machine after it is set up. It also

lists the detailed specifications of the machine. You can download Operating Instructions from the

RICOH home page.

http://www.ricoh.com/

4

1. Safety Information for this Machine

This chapter describes the safety precautions.

Safety Symbols for This Machine

The meanings of the safety symbols for this machine are as follows:

Caution

Prohibition

No disassembly

Caution, risk of electric shock

Refer to instruction manual (Please

refer to page 8 "Battery safety

notice" of Read This First)

5

Safety Information

Safety During Operation

In this manual, the following important symbols are used:

Indicates a potentially hazardous situation which, if instructions are not followed, could result in death

or serious injury.

Indicates a potentially hazardous situation which, if instructions are not followed, may result in minor

or moderate injury or damage to property.

Safety Precautions to Be Followed

This section explains safety precautions that should always be followed when using this machine.

• Be sure to locate the machine as close as possible to a wall outlet. This will allow easy

disconnection of the power cord in the event of an emergency.

• Do not place vases, plant pots, cups, toiletries, medicines, small metal objects, or containers

holding water or any other liquids, on or close to this machine. Since there are openings on the

top and side surfaces of this machine, fire or electric shock could result if liquids or foreign

substances get into the machine.

• The supplied power cord is for use with this machine only. Do not use it with other appliances.

Doing so could result in fire or electric shock.

• Do not place the machine near water, like a spa or pool, or in a position which will allow the

splashing or spraying of water onto the display, like in front of an open window where rain

water may enter. Fire or electric shock could result from spillage or if such objects or substances

fall inside this machine.

• Use only genuine accessories or accessories recommended by the manufacturer to mount the

main unit. Using wrong or unsuitable accessories may cause the main unit to fall and result in

serious personal injuries. Make sure that the surface and fixing points are strong enough to

sustain the weight of the main unit.

1. Safety Information for this Machine

6

• To reduce the risk of electric shock, do not remove covers. No user serviceable parts inside.

Refer all servicing to qualified service personnel.

• Only mount the display that is supported by this stand. If you attempt to use another display

with this stand, the display might fall off the stand, become damaged, or tip over. For

information about the supported models, see the RICOH web site (http://www.ricoh.com/).

• The following explains the warning messages on the plastic bag used in this product's

packaging.

• Keep the polythene materials (bags, etc.) supplied with this machine away from babies

and small children at all times. Suffocation can result if polythene materials are brought into

contact with the mouth or nose.

• If metal objects, or water or other fluids fall inside this machine, you must turn off its power

immediately. After turning off the power, be sure to disconnect the power cord plug from the

wall outlet. Then contact your service representative and report the problem. Do not use the

machine. Doing so could result in fire or electric shock.

• It is dangerous to handle the power cord plug with wet hands. Doing so could result in electric

shock.

• Be sure to disconnect the plug from the wall outlet at least once a year and check for the

following:

• There are burn marks on the plug.

• The prongs on the plug are deformed.

• If any of the above conditions exist, do not use the plug and consult your dealer or service

representative. Use of the plug could result in fire or electric shock.

• Be sure to disconnect the power cord from the wall outlet at least once a year and check for the

following:

• The power cord's inner wires are exposed, broken, etc.

• The power cord's coating has a crack or dent.

• When bending the power cord, the power turns off and on.

• Part of the power cord becomes hot.

• The power cord is damaged.

• If any of the above conditions exist, do not use the power cord and consult your dealer or

service representative. Use of the power cord could result in fire or electric shock.

Safety Information

7

• Do not place the machine on an uneven, sloping or unstable surface (such as a trolley) where it

may fall and cause damage to itself or others.

• When assembling the stand, mounting the main unit on a wall, or installing the main unit, make

sure to contact your local dealer. Do not attempt to perform the installation by yourself.

• Do not install the machine in a confined space without proper ventilation and air circulation,

such as in a closed cabinet. Allow proper space around the machine for dissipating heat

inside. Do not block any openings and vents on the machine. Overheating may result in

hazards and electric shock.

• To prevent personal injuries, mounting the main unit or installing the stand is required before

use.

• Avoid placing the display in direct sun or where direct sun or spot lighting will shine onto the

LCD panel, as the heat may damage the panel and the external casing of the display, and the

bright light will make viewing the display more difficult than necessary.

• Do not obstruct the machine's air inlet or outlet. Doing so risks fire caused by overheated

internal components or resulting in damage to the product.

• Do not allow foreign objects to enter the machine from the air inlet or outlet.

• Be sure to disconnect the plug from the wall outlet and clean the prongs and the area around

the prongs at least once a year. Allowing dust to build up on the plug constitutes a fire hazard.

Safety notice for remote control

• Do not expose the remote control to water or moisture. Failure to do so could result in

malfunction.

Battery safety notice

• Always ensure that the batteries are inserted with the positive and negative terminals in the

correct direction as shown in the battery compartment.

1. Safety Information for this Machine

8

• Do not mix old and new batteries. Mixing old and new batteries will shorten battery life or

cause chemical leaks from the old batteries.

• Chemicals which leak from batteries may cause skin irritation. If any chemical matter seeps out

of the batteries, wipe it up immediately using a dry cloth, and replace the batteries as soon as

possible.

• Different types of batteries have different characteristics. Do not mix different types.

• There is a risk of explosion if a battery is replaced with an incorrect type of battery. Dispose of

used batteries according to the instructions.

Handling the machine's interior

This section explains safety precautions about handling the machine's interior.

• Do not remove any covers or screws that are not mentioned in this manual. Contact your

service representative if any of the product's internal components require maintenance,

adjustment, or repair.

• Do not disassemble or modify the product. Doing so may cause injury or malfunction.

• If the machine's interior is not cleaned regularly, dust will accumulate. Fire and breakdown can

result from heavy accumulation of dust inside this machine. Contact your sales or service

representative for details about and charges for cleaning the machine's interior.

Safety Information

9

Safety Labels of This Machine

This section explains the machine's safety information labels.

Positions of WARNING and CAUTION labels

This machine has labels for WARNING and CAUTION. For safety, please follow the instructions

and handle the machine as indicated.

Symbols for Earth and Power Switch

Symbols for earth and power switch that are used for this machine are as follows:

• : Earth

• : STANDBY

1. Safety Information for this Machine

10

Important Safety Instructions

1. Read this manual carefully.

2. Keep this manual handy for future reference.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus

(including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has

two blades with one wider than the other. A grounding-type plug has two blades and a third

grounding prong. The wide blade or the third prong are provided for your safety. If the provided

plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience

receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the stand or bracket specified by the manufacturer, or sold with the apparatus. When

a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-

over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has

been damaged in any way, such as power-supply cord or plug is damaged, liquid has been

spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or

moisture, does not operate normally, or has been dropped.

Important Safety Instructions

11

Notes on the LCD Panel of the Machine

• The Liquid Crystal Display (LCD) panel of this display has a very thin protective layer of glass which

is liable to marking or scratching, and cracking if struck or pressured. The liquid crystal substrate is

also liable to damage under excessive force or extreme temperatures. Please handle with care.

• The response time and brightness of the LCD panel may vary with the ambient temperature.

• The LCD panel consists of individual pixels to display images and is manufactured according to the

design specifications. While 99.99% of these pixels work normally, 0.01% of the pixels may

remain constantly lit (in red, blue or green) or unlit. This is a technical limitation of the LCD

technology and is not a defect.

• LCD screens, like plasma (PDP) and conventional CRT (Cathode Ray Tube) screens, are also

susceptible to 'screen burn-in' or 'image retention' which can be found on the screen as visible fixed

lines and shades. To avoid such damage to the screen, avoid displaying still images (like On-

Screen Display menus, TV station logos, fixed/inactive text or icons) for more than two hours.

Change the aspect ratio from time to time. Fill the entire screen with the image and eliminate the

black bars whenever possible. Avoid displaying images in 4:3 aspect ratio over a long period of

time, otherwise there may be visible burn marks on the screen as two vertical lines.

1. Safety Information for this Machine

12

2. Information for This Machine

This chapter describes laws and regulations related to this machine.

Laws and Regulations

Warning on Class A Product

Warning:

This equipment is compliant with Class A of CISPR 32. In a residential environment this equipment may

cause radio interference.

As this machine is not a household appliance, it does not conform to ErP Directive 2009/125/EC

which was revised in 2013.

CE Marking Traceability Information (For EU Countries Only)

Manufacturer:

Ricoh Co., Ltd.

3-6 Nakamagome 1-chome, Ohta-ku, Tokyo. 143-8555, Japan

Importer:

Ricoh Europe PLC

20 Triton Street, London. NW1 3BF, United Kingdom

User Information for Wireless Network (For EU Countries Only)

Declaration of Conformity

Notice to Users in EEA Countries

This product complies with the essential requirements and provisions of Directive 2014/53/EU.

The CE Declaration of Conformity is available by accessing the URL: http://www.ricoh.co.jp/fax/

ce_doc/

and selecting the product applicable.

13

Overseas Affiliates and Noise Emission Information

In accordance with TUV “GS Symbol” requirements, details of the EU office or representative

company are given below.

Overseas Affiliates

Ricoh Europe PLC

20 Triton Street, London. NW1 3BF, United Kingdom

Noise Emission

Maschinenlärminformations-Verordnung 3. GPSGV:

Der höchste Schalldruckpegel beträgt 70 dB(A) oder weniger gemäss EN ISO 7779

User Information on Electrical and Electronic Equipment

Users in the countries where this symbol shown in this section has been specified in

national law on collection and treatment of E-waste

Our Products contain high quality components and are designed to facilitate recycling.

Our products or product packaging are marked with the symbol below.

The symbol indicates that the product must not be treated as municipal waste. It must be disposed of

separately via the appropriate return and collection systems available. By following these instructions

you ensure that this product is treated correctly and help to reduce potential impacts on the environment

and human health, which could otherwise result from inappropriate handling. Recycling of products

helps to conserve natural resources and protect the environment.

For more detailed information on collection and recycling systems for this product, please contact the

shop where you purchased it, your local dealer or sales/service representatives.

All Other Users

If you wish to discard this product, please contact your local authorities, the shop where you bought this

product, your local dealer or sales/service representatives.

2. Information for This Machine

14

For Users in India

This product including components, consumables, parts and spares complies with the "India E-waste

Rule" and prohibits use of lead, mercury, hexavalent chromium, polybrominated biphenyls or

polybrominated diphenyl ethers in concentrations exceeding 0.1 weight % and 0.01 weight % for

cadmium, except for the exemptions set in the Rule.

For Turkey only

Note for the Battery and/or Accumulator Symbol (For EU countries only)

In accordance with the Battery Directive 2006/66/EC Article 20 Information for end-users Annex II,

the above symbol is printed on batteries and accumulators.

This symbol means that in the European Union, used batteries and accumulators should be disposed of

separately from your household waste.

In the EU, there are separate collection systems for not only used electrical and electronic products but

also batteries and accumulators.

Please dispose of them correctly at your local community waste collection/recycling centre.

Notes to USA Users of FCC Requirements

Note:

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This

Laws and Regulations

15

equipment generates, uses and can radiate radio frequency energy and, if not installed and used

in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his own expense.

Caution:

Changes or modifications not expressly approved by the party responsible for compliance could

void the user's authority to operate the equipment.

Using the shield cable

Properly shielded and grounded cables and connectors must be used for connections to a host computer

(and/or peripheral) in order to meet FCC emission limits.

Installing the ferrite core

Ferrite core must be used for RF interference suppression.

Notes to users in the United States of America

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired

operation.

This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

Notes to Canadian Users of Wireless Devices

This device complies with Industry Canada’s licence-exempt RSSs.

Operation is subject to the following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause undesired operation

of the device.

2. Information for This Machine

16

La page est en cours de chargement...

Ricoh D5520 Read this first

Ce manuel convient également à

Ricoh D5520 Read this first

dans d''autres langues

Documents connexes

Autres documents