Paramount EF-WM391 MO Manuel utilisateur

Marque
Paramount
Modèle
EF-WM391 MO
Catégorie
Cheminées
Taper
Manuel utilisateur
Page 1
1
YEAR
limited
WARRANTY
Wall Mount Fireplace
With Adjustable Mounting Bracket
Owner’s Manual
Model Number Item Number
JR42 EF-WM353 MO (42”)
JR42 WHITE EF-WM373 MO (42”)
JR50 EF-WM350 MO (50”)
*Patented Flame Technology & Front Venting Design
READ & SAVE THESE INSTRUCTIONS
Carefully read and review before assembling, installing, operating, or maintaining
this product. Observe all safety instructions and information.
FAILURE TO FOLLOW WARNINGS & OPERATIONAL INSTRUCTIONS CONTAINED IN THIS
MANUAL CAN RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY
**IMPORTANT NOTICE**
For customer service & warranty issues, please contact: [email protected]
07.17.18
EF-WM391 MO (50”)
JR60 EF-WM349 MO (60”)
JR72 EF-WM348 (72”)
JR50 WHITE
Page 2
Introduction
WARNING
• THIS APPLIANCE IS HOT WHEN OPERATED AND CAN CAUSE SEVERE BURNS IF CONTACTED.
• Do not operate appliance before reading and understanding operating instructions. Failure to operate appliance
accordingtooperatinginstructionscouldcausereorinjury.
• Risk of burns. Power to the appliance should be turned off and the appliance allowed to cool before servicing. To
disconnect power to the appliance, turn controls to off, then remove plug from outlet.
• Do not install damaged, incomplete or substitute components.
• Do not burn wood or other materials in this appliance.
• Young children should be carefully supervised when they are in the same room as the appliance. Toddlers, young
children and others may be susceptible to accidental contact burns. A physical barrier is recommended if there are
at risk individuals in the house. To restrict access to an appliance or stove, install an adjustable safety gate to keep
toddlers, young children and other at risk individuals out of the room and away from hot surfaces.
• Clothingorotherammablematerialshouldnotbeplacedonorneartheappliance.
• Duetohightemperatures,theapplianceshouldbelocatedoutoftrafcandawayfromfurnitureanddraperies.
• Ensure you have incorporated adequate safety measure to protect infants/toddlers from touching hot surfaces.
• Even after the appliance is out, the glass and/or screen will remain hot for an extended period of time.
• Check with your local hearth specialty dealer for safety screens and hearth guards to protect children from hot
surfaces.Thesescreensandguardsmustbefastenedtotheoor.
• Any safety screen or guard removed for servicing must be replaced prior to operating the appliance.
• It is imperative that the control compartments, circulating blower and its passageway in the appliance and are kept
clean.Theapplianceshouldbeinspectedbeforeuseandatleastannuallybyaqualiedserviceperson.More
frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc. The appliance area
mustbekeptclearandfreefromcombustiblematerials,gasolineandotherammablevaporsandliquids.
• Undernocircumstancesshouldthisappliancebemodied.
• Donotusethisapplianceifanyparthasbeenunderwater.Immediatelycallaqualiedservicetechniciantoinspect
the appliance and to replace any part of the control system which has been under water.
• Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the glass should be
donebyalicensedorqualiedserviceperson.
• Do not strike or slam shut the appliance glass door.
• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As with all plastic
bags, these are not toys and should be kept away from children and infants.
• Servicing should be done only while the appliance is disconnected from the power supply circuit.
• Always unplug appliance when not in use.
• Do not operate this appliance with a damaged cord or plug after the appliance malfunctions, has been dropped or
damaged in any manner. Return appliance to authorized service facility for examination, electrical or mechanical
adjustment, or repair.
• Do not use outdoors.
• Never locate appliance where it may fall into a bathtub or other water container.
• Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or the like. Arrange cord away from
trafcareaandwhereitwillnotbetrippedover.
• Connect to properly grounded outlets only.
• Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric
shockorre,ordamagetheappliance.
• Topreventapossiblere,donotblockairintakesorexhaustinanymanner.Donotuseonsoftsurfaces,likea
carpet, where openings may become blocked.
• Always plug appliances directly into a wall outlet/receptacle. Never use an extension cord or relocatable power tap
(outlet/power strip).
• Ensure clearances to combustibles are maintained when building a mantel or shelves above the appliance.
Elevated temperatures on the wall or in the air above the appliance can cause melting, discolouration or damage to
decorations, a T.V. or other electronic components.
07.17.18
Page 3
Dimensions
Listing Approvals
FRONT VIEW
TOP VIEW
SIDE VIEW
ThisappliancehasbeentestedinaccordancewiththeCSAStandardsforxedandlocation-dedicated
electric room appliances in the United States and Canada. If you need assistance during installation, please
contact your local dealer.
NOTE: This appliance must be electrically wired and grounded in accordance with local codes or,
in the absence of local codes, with National Electric Code ANSI/NFPA 70-latest edition in the United
States or the Canadian Electric Code, CSA C22.1 in Canada.
PRODUCT DIMENSIONS CARTON DIMENSIONS
Item No. A B C D E F G Width x Depth x Height
EF-WM350 MO 20” 4.2” 18.8” 9.72”
50” 20” 4.2” 18.8” 44.10” 9.72” 39.72” 56.89” x 10.24” x 25.59”
EF-WM349 MO 60” 20” 4.2” 18.8” 54.10” 9.72” 50”
66.93” x 10.24” x 25.59”
EF-WM348 72” 23.25” 4.2” 20.27” 66.10” 10.24” 60”
79.53” x 11.22” x 29.92”
Item No. Net Weight Gross Weight
EF-WM353 MO 22 KGS 29.5 KGS
EF-WM349 MO 31.5 KGS 41.5 KGS
EF-WM 348 43.5 KGS 56.0 KGS
Description Electric Fireplace
Type 3 Way Mounting Wall Mount
Voltage 120V AC
Watts MAX 1500W
Amps 15 AMP Grounded Circuit
E
D
C
07.17.18
EF-WM391 MO
50”
44.10” 39.72”
56.89” x 10.24” x 25.59”
EF-WM353 MO 42” 20” 4.2” 18.8” 36.10” 9.72” 31.97” 49” x 10.24” x 25.59”
EF-WM373 MO 20” 4.2” 18.8” 9.72”
42”
36.10”
49” x 10.24” x 25.59”31.97”
29.5 KGS
EF-WM373 MO
26.5 KGS
35.0 KGS
EF-WM350 MO
26.5 KGS 35.0 KGS
22 KGS
EF-WM391 MO
A
G
F
B
Page 4
General Instructions
READ THESE INSTRUCTIONS COMPLETELY BEFORE BEGINNING INSTALLATION. FAILURE TO
FOLLOW THEM COULD CAUSE AN APPLIANCE MALFUNCTION RESULTING IN SERIOUS INJURY
AND/OR PROPERTY DAMAGE.
ALL ELECTRIC APPLIANCES HAVE HOT AND ARCING OR SPARKING PARTS INSIDE. DO NOT USE IT
IN AREAS WHERE GASOLINE, PAINT OR FLAMMABLE LIQUIDS ARE PRESENT.
THIS ELECTRIC APPLIANCE IS TESTED AND LISTED FOR USE ONLY WITH THE OPTIONAL
ACCESSORIES LISTED IN THESE INSTRUCTIONS. USE OF OPTIONAL ACCESSORIES NOT
SPECIFICALLY TESTED FOR THIS ELECTRIC APPLIANCE COULD VOID THE WARRANTY AND/OR
RESULT IN A SAFETY HAZARD.
DO NOT OPEN. RISK OF ELECTRIC SHOCK. NO USER-SERVICEABLE PARTS INSIDE.
DO NOT USE DAMAGED ELECTRICAL CORDS.
SERVICING SHOULD BE DONE ONLY WHILE THE APPLIANCE IS DISCONNECTED FROM THE
POWER SUPPLY CIRCUIT.
TO PREVENT ELECTRIC SHOCK MATCH THE WIDE BLADE OF PLUG TO WIDE SLOT OF
RECEPTACLE AND FULLY INSERT.
1. Prior to plugging your appliance into an electrical outlet, verify that the house circuit breakers for the
outlet are on.
2. Theappliancemayemitaslight,harmlessodourwhenrstused.Thisodourisnormalanditiscaused
by the initial heating of internal appliance elements and will not occur again.
3. If your appliance does not emit heat, consult the operation section of this manual for further information.
4. UsewithaCSAorULcertiedsurgeprotector.
5. Do not route the power cord directly underneath the appliance.
This electric appliance meets the construction and safety standards of H.U.D. for application in
manufactured homes when installed according to these instructions.
Aswithmostelectronicdevices,yournewelectricreplacehasbeendesignedtooperateat
temperatures between 5°C (41°F) and 35° C (95°F). During the colder winter months, allow the
replacetoreachroomtemperaturebeforeturningiton.
WARNING
Unpacking and Testing Appliance
Carefully remove the appliance from the box. Prior to installing the appliance, test to make sure the appliance
operates properly by plugging the power supply cord into a conveniently located 120 Volt grounded outlet.
07.17.18
Page 5
EF-WM353 MO (42”) x2
EF-WM350 MO (50”) x2
EF-WM349 MO (60”) x2
EF-WM348 (72”) x2
EF-WM353 MO (42”) x1
EF-WM373 MO (42”) x1
EF-WM349 MO (60”) x1
EF-WM348 (72”) x1
EF-WM353 MO (42”) x8
EF-WM350 MO (50”) x8
EF-WM349 MO (60”) x26
EF-WM348 (72”) x32
EF-WM353 MO (42”) x9
EF-WM373 MO (42”) x9
EF-WM349 MO (60”) x13
EF-WM348 (72”) x16
EF-WM353 MO (42”) x4
EF-WM373 MO (42”) x4
EF-WM349 MO (60”) x4
EF-WM348 (72”) x4
EF-WM349 MO (60”) x6
EF-WM348 (72”) x8
EF-WM349 MO (60”) x6
EF-WM348 (72”) x8
F- Drywall AnchorsD- Mounting Bracket
L- Cord Cover
E- Wood Screws
A- Fireplace B- Side Brackets
OPTIONAL
For kit of OPTIONAL
parts J, K, L
(Item No: EF-WC)
contact:
1-800-561-5550
OPTIONALOPTIONAL
C1 - Top/Bottom Brackets C2 - Top/Bottom Brackets
G- ST4x12 Metal Screws
I- Crystals
J- Cord Corner K- Cord Corner
H- Remote Control
Hardware Parts List
07.17.18
EF-WM350 MO (50”) x1
EF-WM391 MO (50”) x1
EF-WM350 MO (50”) x4
EF-WM391 MO (50”) x4
EF-WM350 MO (50”) x13
EF-WM391 MO (50”) x13
EF-WM353 MO (42”) x1
EF-WM373 MO (42”) x1
EF-WM349 MO (60”) x1
EF-WM348 (72”) x1
EF-WM350 MO (50”) x1
EF-WM391 MO (50”) x1
EF-WM353 MO (42”) x9
EF-WM373 MO (42”) x9
EF-WM349 MO (60”) x13
EF-WM348 (72”) x16
EF-WM350 MO (50”) x13
EF-WM391 MO (50”) x13
EF-WM391 MO (50”) x8
EF-WM373 MO (42”) x8
EF-WM353 MO (42”) x1
EF-WM373 MO (42”) x1
EF-WM349 MO (60”) x1
EF-WM348 (72”) x1
EF-WM350 MO (50”) x1
EF-WM391 MO (50”) x1
EF-WM353 MO (42”) x1
EF-WM373 MO (42”) x1
EF-WM349 MO (60”) x1
EF-WM348 (72”) x1
EF-WM350 MO (50”) x1
EF-WM391 MO (50”) x1
EF-WM391 MO (50”) x2
EF-WM373 MO (42”) x2
EF-WM353 MO (42”) x2
EF-WM350 MO (50”) x2
EF-WM349 MO (60”) x2
EF-WM348 (72”) x2
EF-WM391 MO (50”) x2
EF-WM373 MO (42”) x2
EF-WM353 MO (42”) x2
EF-WM350 MO (50”) x2
EF-WM349 MO (60”) x2
EF-WM348 (72”) x2
EF-WM391 MO (50”) x2
EF-WM373 MO (42”) x2
Page 6
Locating Appliance
DUE TO HIGH TEMPERATURES, THIS ELECTRIC APPLIANCE SHOULD BE LOCATED OUT OF
TRAFFIC. KEEP COMBUSTIBLE MATERIALS SUCH AS FURNITURE, PILLOWS, BEDDING, PAPERS,
CLOTHES AND CURTAINS AT LEAST 36” FROM THE FRONT OF THE APPLIANCE.
NEVER LOCATE THIS ELECTRIC APPLIANCE WHERE IT MAY FALL INTO A BATHTUB OR OTHER
WATER CONTAINER.
WEAR SAFETY GLOVES AND SAFETY GLASSES FOR PROTECTION DURING INSTALLATION AND
MAINTENANCE.
TO PREVENT CONTACT WITH SAGGING OR LOOSE INSULATION, THE ELECTRIC APPLIANCE
MUST NOT BE INSTALLED AGAINST VAPOR BARRIER OR EXPOSED INSULATION. LOCALIZED
OVERHEATING COULD OCCUR AND A FIRE COULD RESULT.
DO NOT EXPOSE THE ELECTRIC APPLIANCE TO THE ELEMENTS (SUCH AS RAIN, ETC.)
WARNING
This appliance is for use on 120 Volts. The cord
has a plug as shown in (A). An adapter as shown
in (C) is available for connecting three-blade
grounding type plugs to two-slot receptacles. The
green grounding lug extending from the adapter
must be connected to a permanent ground such
as a properly grounded outlet box. The adapter
should not be used if a three-slot grounded
receptacle is available.
To disconnect appliance, turn controls to off, then
remove plug from outlet.
METAL SCREW
(A)
NOT ALLOWED IN CANADA
GROUNDING
MEANS
ADAPTER
GROUNDING PIN
COVER OF
GROUNDED
OUTLET BOX
(C)
(B)
GROUNDING METHODS
Grounding Appliance
07.17.18
Page 7
Installation
Minimum Clearance to Combustibles
Minimum Mantel Clearances
RISK OF FIRE! THE POWER CORD MUST NOT BE PINCHED AGAINST A SHARP EDGE. SECURE
CORD TO AVOID TRIPPING OR SNAGGING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR
PERSONAL INJURY. DO NOT RUN CORD UNDER CARPETING. DO NOT COVER CORD WITH THROW
RUGS, RUNNERS OR THE LIKE. ARRANGE CORD AWAY FROM TRAFFIC AREAS AND WHERE IT
WILL NOT BE TRIPPED OVER.
RISK OF FIRE! TO PREVENT A POSSIBLE FIRE, DO NOT BLOCK AIR INTAKE OR EXHAUST IN ANY
MANNER. DO NOT USE ON SOFT SURFACES WHERE OPENINGS MAY BECOME BLOCKED.
RISK OF FIRE! DO NOT BLOW OR PLACE INSULATION AGAINST THE APPLIANCE.
THIS ELECTRIC APPLIANCE IS TESTED AND LISTED FOR USE ONLY WITH THE APPROVED
OPTIONAL ACCESSORIES. USE OF OPTIONAL ACCESSORIES NOT SPECIFICALLY TESTED FOR
THIS ELECTRIC APPLIANCE COULD VOID THE WARRANTY AND/OR RESULT IN A SAFETY HAZARD.
IF THE INFORMATION IN THESE INSTRUCTIONS IS NOT FOLLOWED EXACTLY, A FIRE OR EXPLOSION
MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. DO NOT STORE OR USE
GASOLINE OR OTHER FLAMMABLE VAPORS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE.
THIS APPLIANCE IS HEAVY. IT IS HIGHLY RECOMMENDED THAT TWO PEOPLE INSTALL THIS APPLIANCE.
HEATER VENTS ON THE ELECTRIC APPLIANCE CANNOT, IN ANY WAY, BE COVERED AS IT MAY
CREATE A FIRE HAZARD.
DO NOT RUN THE POWER CORD HORIZONTALLY, DIRECTLY BELOW THE APPLIANCE.
WHEN USING PAINT OR LACQUER TO FINISH THE MANTEL, THE PAINT OR LACQUER MUST BE
HEAT RESISTANT TO PREVENT DISCOLOURATION.
WARNING
WARNING
Your JR42/50/60/72 unit is a wall-mounted appliance. Select a suitable location that is not susceptible to
moistureandisawayfromdrapes,furnitureandhightrafcareas.
NOTE: Follow all National and local electrical codes.
Bottom
Sides
Back
0”
0”
0”
Top
Top
Measurements are taken from the glass front
8” (203mm) to mantel
8” (203mm) to ceiling
07.17.18
Page 8
No Recess:
- Easy installation
- Full use of backlight
- Easy maintenence
For installation
instructions refer
to Page 12
Adjustable Mounting Brackets and Installation Options
Full Recess:
- Flush to wall look
- No use of backlight
For installation
instructions refer
to Page 9
Partial Recess:
- 1” gap for multi-use
- No use of backlight
- Easy maintenence
For installation
instructions refer
to Page 9
FIG. 2
SIDE
VIEW
TOP
VIEW
PARTS
NEEDED
FIG. 3 FIG. 4
NOTE:Itisrecommendedthatthewallsfortheapplianceenclosurebenished(ie.drywall)to
avoid exposed insulation or vapour barriers coming in contact with the appliance. This will ensure
clearance to combustibles is maintained.
OPTION 1 OPTION 2 OPTION 3
B + C1 or C2
(JR42/JR50: B only) (JR42/JR50: B only)
B + C1 or C2D
07.17.18
Page 9
Option 1: Recessing the Appliance Flush into the Wall
Duetothemanydifferentnishmaterialsusedonwalls,itishighlyrecommendedthatyouconsultyourlocal
builder before you install this appliance in the wall.
Select a location that is not prone to moisture and is located at least 36” (914mm) away from combustible
materials such as curtain drapes, furniture, bedding, paper etc.
C1 or C2
B
1. Measure the appliance and create a rough in
with electrical.
2. Remove the front glass (refer to Page 15 for
instructions).
3. Remove the LED back lights (refer to Page 16
for instructions).
4. Holdtheapplianceuptoensureitwilltintothe
framing.
5. To fully recess the appliance into the wall:
A. Position and screw the side Builder’s
brackets (shown in grey on Page 10) to the set
of holes closest to the front glass as in Figure 2
on Page 8.
B. Use 8-24 screws (provided) to lock appliance
into wall from the side facing out.
C. Install the media and reinstall the glass front.
6. To partially recess the appliance into the
wall (Option 3):
A. Position and screw the side Builder’s
brackets (shown in grey on Page 10) to the
second set of holes from the front glass as in
Figure 4 on Page 8.
B. Use 8-24 screws (provided) to lock appliance
into wall from the side facing out.
C. Install the media and reinstall the glass front.
NOTE: Two sets of holes are provided for
recessing into the wall. The wall structure
may limit how far the appliance can be
recessed. Use the appropriate set of holes
when recessing to the frame, it may be
necessary to use the four holes on the top
and bottom.
FRONT VIEW
07.17.18
Page 10
Positioning of Adjustible Builder’s Brackets
EF-WM353 MO,
EF-WM349 MO
Builder’s bracket positions
shown in grey for each model
EF-WM348
B: Side brackets
C1: Top bracket (Tall)
Use for more security & surface area
C2: Top bracket (Short)
Usedwhennowallnishisapplied.
Will stay hidden behind glass.
B
B
B
C2
C2
07.17.18
EF-WM373 MO,
EF-WM391 MO
EF-WM350 MO,
Page 11
Minimum Clearance to Combustibles
Framing
Sides, back and top 0”
Measurements are taken from the glass front
Item No. A C D EB
EF-WM353 MO
EF-WM373 MO
EF-WM349 MO
EF-WM348
Recommended Framing Dimensions
Finishing Material
(NON-LOAD
BEARING)
A
A
B
B
19.3” (49cm) 38.60” (98cm)
19.3” (49cm)
19.3” (49cm) 56.60” (143.8cm)
21.27” (52.8cm) 68.60”
4.2”
4.2”
4.2”
4.2”
18.8”
18.8”
18.8”
18.8”
36.10”
54.10”
66.10” (174.2cm)
NOTE to installer: Please allow extra clearance for the power cord and easy installation.
TOP VIEWSIDE VIEW
E
D
C
07.17.18
EF-WM391 MO
19.3” (49cm) 46.60” (118.4cm)
4.2” 18.8” 44.10”
EF-WM350 MO
19.3” (49cm) 46.60” (118.4cm)
4.2” 18.8” 44.10”
38.60” (98cm)
36.10”
Page 12
Option 2: Hanging the Appliance on the Wall
Due to the many different materials used on different walls, it is highly
recommended that you consult your local builder before you install this
appliance on the wall.
1. Select a location that is not prone to moisture and is located at
least 36” (914mm) away from combustible materials such as curtain
drapes, furniture, bedding, paper, etc.
2. Have two people hold the appliance against the wall to determine the
location.
3. Remove the bracket from the back of the unit by removing the two
screws, refer to Figure 1.
4. Mark out location, then mount the bracket onto the wall using the 8
supplied screws. This bracket MUST have the hooks facing upward
and be level.
WALL MOUNT
BRACKET
SCREWS
HOOK
HOOK
NOTE: It is strongly recommended
that the mounting bracket be
screwed into the wall studs where
possible. If the wall studs cannot
be used, ensure that the supplied
plastic anchors are used to the
bracket to the wall and the bracket
is adequately secured.
5. With the wall mounting bracket installed have two people lift the appliance up and insert the two
hooks on the bracket into the two slots on the back of the appliance.
6. Check the appliance for stability ensuring that the bracket will not pull free from the wall.
BODY
FRONT
GLASS
SIDE VIEW
Figure 1
Bracket
07.17.18
Page 13
1. Remove the cover plate from the right side of the appliance by removing the four screws, as shown above.
2. Remove the wire connectors from the power cord. The power cord may be discarded.
3. Take the new cover plate, supplied in the manual bag. Punch out the 7/8” (22mm) hole and install a box
connector through, into the junction box. Snap the box connector clamp onto the supply wires.
4. Using the wire connectors, connect the ground green wires (G) and white wires (N) together, then hot
black wires (L) and then refer to Figure 2.
5. Reinstall the cover plate using the four screws, as shown in Figure 1.
NOTE: Leave enough wire so that the appliance can be removed from the enclosure without
disconnecting the power supply.
HARD WIRING CONNECTION
Ifitisnecessarytohardwirethisappliance,aqualiedelectricianmustremovethecordconnection,and
wire the appliance directly to the house hold wiring.
This appliance must be electrically connected and grounded in accordance with local codes, if hard wired. In
the absence of local codes, use the current CSA C22.1 CANADIAN ELECTRICAL CODE in Canada or the
current ANSI/NFPA 70 NATIONAL ELECTRICAL CODE in the United States.
COVER PLATE
Figure 1
Figure 2
Hard Wiring Installation
TURN OFF THE APPLIANCE COMPLETELY AND LET COOL BEFORE SERVICING. ONLY A QUALIFIED
SERVICE PERSON SHOULD SERVICE AND REPAIR THIS ELECTRIC APPLIANCE.
WARNING
G
N
L
07.17.18
Page 14
1. Remove the 4 screws from the sides of the appliance in Figure 1.
2. Have two people lift the glass up and away from the appliance, holding the glass vertical while carrying.
Carefully rest the glass on a soft, non-abrasive surface.
3. Install the crystal embers (refer to instructions on Page 16)
4. Re-install the front glass by aligning the slots with the pins on the side of the appliance. Press the glass
down to secure in place.
5. Secure the front glass using the 4 screws in Figure 1. (If fully recessed, this is not necessary)
Front Glass Removal / Installation
POWER SUPPLY SERVICE MUST BE COMPLETED PRIOR TO FINISHING TO AVOID RECONSTRUCTION.
HEAT VENTS AND AIR OPENINGS CANNOT BE COVERED IN ANY CIRCUMSTANCES.
BEFORE THE FRONT GLASS IS INSTALLED OR REMOVED, UNPLUG THE APPLIANCE AND WAIT UNTIL
APPLIANCE IS COOL TO THE TOUCH. GLASS CAN BE HEAVY AND FRAGILE SO HANDLE WITH CARE.
WARNING
WARNING
FinishingFinishing
Figure 1
07.17.18
Page 15
The glass front must be removed and the appliance must be secured in its location before the crystal
embers are installed.
1. Carefully place crystal embers into the bottom media tray on the front of the appliance as illustrated.
Apply an even layer from side to side.
LED Back Light Removal
The glass front must be removed and the appliance must be secured in its location before the crystal
embers are installed.
1. Unscrew the two screws in Figure A.
2. Lift off the LED cover and remove.
3. Disconnect the wires where connected to the circuit board. The disassembly is complete.
Crystal Embers Installation
07.17.18
Page 16
Main Power Switch
Operating with Touch Panel
Once the appliance has been plugged into a grounded electrical outlet, it is ready to operate.
NOTE: Ensure the house circuit breakers for the power supply are turned on. In the event of a power
failure, the appliance will lose its memory function and will reset to factory mode when the power
returns.
To turn unit power on:
1. Plug in power cord.
2. Turn on the power switch (located on the front bottom right side of the appliance).
3. Verify the power is turned on when two ring tones are initiated.
The unit can be controlled by either the touch panel controls which are located on the right side of the front
glass or the remote control.
1. Press “ ” to turn on and off the appliance.
2. Press “ ” multiple times to adjust between mid, low, on/off, or high brightness options
3. Press “ ” multiple times to set operating duration to 30 min, 1h, 2h, 3h, 4h, 5h, 6h, 7h, 8h, or off.
4.
Note: The touch panel buttons will glow when pressed. The light fades in 5 seconds after pressing.
Operating Instructions
WHILE THE APPLIANCE IS OPERATING DO NOT REMOVE THE GLASS PANEL. THIS WILL CAUSE THE
REMOTE CONTROL AND TOUCH PANEL TO DISFUNCTION.
WARNING
ON/OFF
Power
Flame Timer Heater Indicator
05.17.18
Press “ ” multiple times to set ambient temperatures at 18°C, 19°C, 20°C, 21°C, 22°C, 23°C, 24°C,
25°C,26°C,27°C,28°C,ONorOFF.Whensettingthetemperature,thenumberwillash.
Page 17
Multi-functional Operating with Remote Control
Turning ON/OFF the appliance:
1. Ensuresteps1-3inthe“MainPowerSwitch”procedurearerstfollowed.
2. Pressthe“”remotebuttontoturnonbothameandemberbedLEDs.
3. Pressthe“”buttonagaintoturnoffbothameandemberbedLEDS.
4. Verify the lights are shut off.
5. Turn off the main power swtich.
6. Unplug the power cord.
Note: The LEDs are at the brightest when the heating element is shut off. The
power swtich on the appliance must be turned on for the remote control to operate.
Changing the temperature:
1. Ensure steps 1-2 in “Turning ON/OFF the appliance” are previously followed.
2. Press the “ ” button to turn on the heat element to HIGH temperature at
1500W.
3. Press the “ ” button again to decrease the temperature to LOW temperature
at 750W.
4.
Note: Pressing the “ ”or “ ”
a second time turns off the heating element.
Changing LED options:
1. Ensure steps 1-2 or 1-3 in “Turning ON/OFF the appliance” are previously
followed.
2. Pressthe“”buttontoturnonorofftheameandemberbedLEDs.
3. Press the “ ” button multiple times to cycle through 3 different brightness levels and OFF for the yellow
ameLEDs.
4. Press the “ ” button multiple times to cycle through 3 different brightness levels and OFF for the blue
ameLEDs.
5. Press the “ ” button multiple times to cycle through 3 different brightness levels and OFF for the pink
ameLEDs.
6. Press the “ ” button multiple times to set operating duration to 30min, 1h, 2h, 3h, 4h, 5h, 6h, 7h, 8h, or off.
7. Press the “ ” button multiple times to cycle the back LED lights through red, yellow, blue, red/blue, red/
yellow, yellow/blue, red/yellow/blue, fade, or OFF.
Note: Steps 2-7 can be done independently.
11.24.17
07.17.18
Press the “ ” button multiple times to set ambient temperature to 18°C,
19°C, 20°C, 21°C, 22°C, 23°C, 24°C, 25°C, 26°C, 27°C, 28°C, ON or OFF. The
number will appear on touch panel display.
Page 18
RemoteControlSpecications
Storage Instructions
1. MCU Chips: SN8P2722 Chip
2. Software: LRC 12-02
3. Remote: 10 key remote
4. Item No.: EF-WM353 MO, EF-WM373 MO,EF-WM350 MO,
EF-WM391 MO,EF-WM349 MO, EF-WM348
NOTE: Make sure your “AA” batteries (x2) are
fully charged and installed correctly in your
remote control before operating.
The remote control must remain within 5
meters or 17 feet of the appliance to be
effective, this range may be reduced when
battery power is depleted.
Maintenence
PREPARATION FOR MAINTENANCE
ALWAYS DISCONNECT THE POWER AND ALLOW THE ELECTRIC APPLIANCE TO COOL BEFORE
PERFORMING ANY CLEANING, MAINTENANCE OR RELOCATION OF THIS ELECTRIC APPLIANCE.
TURN CONTROLS TO OFF AND REMOVE PLUG FROM OUTLET OR TURN OFF THE HOUSE
CIRCUIT BREAKER TO ELECTRIC APPLIANCE RECEPTACLE.
DO NOT INSTALL REPLACEMENT BULBS THAT EXCEED SPECIFIED MAXIMUM WATTS.
THE BULBS IN YOUR APPLIANCE CAN BECOME EXTREMELY HOT. ALLOW AT LEAST
10 MINUTES BETWEEN TURNING OFF THE APPLIANCE AND REMOVING THE LAMPS TO AVOID
ACCIDENTAL BURNS.
DO NOT HANDLE THE BULBS WITH BARE FINGERS, OILS FROM YOUR SKIN WILL DAMAGE THE
BULS WHEN THEY HEAT UP. USE GLOVES OR A CLEAN DRY CLOTH WHEN HANDLING BULBS.
WARNING
Ensure the power cord is not installed so that it is pinched or against a sharp edge and ensure that the
powercordisstoredorsecuredtoavoidtrippingorsnaggingtoreducetheriskofre,electricshock,or
injury to persons.
Construction and electrical outlet wiring must comply with local building codes and other applicable
regulationstoreducetheriskofre,electricalshock,andinjurytopersons.
Donotattempttowireyourownnewoutletsorcircuits.Toreducetheriskofre,electricshock,orinjuryto
persons, always use a licensed electrician.
07.17.18
Page 19
_
+
[
LRC16 FR-4
2014/09/18
SHENGYI
+ EBY
FN
FIRE_Y
-N1
FN-N1
L_B
L_Y
R1
-N1
-L1
H1
H2
RF
SI1
IC2
R-N1
RELY-H1
C-FF
RELY-H2
C-FF
RELY-H
C-FF
1
E
2
FIRE_B
LE- H
E
YB
+
+
BY
E
C
N2
CN1
+
E
B
Y
+
E
B
Y
Y
Y2
Y1
E
E2
E1
CN1
B
B2
B1
B11
B12
CN2
E11
E12
Y11
Y12
EN
CL

_
S
+
CL
SI1
CN2
CN1
CN2
CN1
-

EN
CL
1
2
G
F
G
C
E
+
CL
S
R8-1
FR-4
201/04/16
SHENGYI
CN2
E
I E
ER
FLE
Wiring Diagram
TURN OFF THE APPLIANCE COMPLETELY AND LET COOL BEFORE SERVICING. ONLY A QUALIFIED
SERVICE PERSON SHOULD SERVICE AND REPAIR THIS ELECTRIC APPLIANCE.
WARNING
FIRE ELEMENT
EMBER
BACKLIGHT 1
BACKLIGHT 2
BUTTON
POWER
CORD
SWITCH
RECEIVER
TEMPERATURE
SENSOR
HEATING ELEMENT
07.17.18
Page 20
Replacement Parts
FAILURE TO POSITION THE PARTS IN ACCORDANCE WITH THIS MANUAL OR FAILURE TO USE ONLY
PARTS SPECIFICALLY APPROVED WITH THIS APPLIANCE MAY RESULT IN PROPERTY DAMAGE OR
PERSONAL INJURY.
WARNING
To order parts, contact [email protected]
FOR WARRANTY REPLACEMENT PARTS, A PHOTOCOPY OF THE ORIGINAL INVOICE WILL BE
REQUIRED TO HONOUR THE CLAIM.
When ordering replacement parts always give the following information:
•Modelandserialnumberofappliance
•Installationdateofappliance
•Partnumber
•Descriptionofpart
•Finish
FOR FURTHER INFORMATION, CONTACT YOUR AUTHORIZED DEALER.
REF.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
EF-WM353 MO
BFT42
BFT42CT
LED42
EBT42
WMB42
B42
N/A
N/A
CE42
FSA42
BHA42
LRC12-02
LRC42
WBL
HWK42
CP42
JR42
TH42
RMOTER
WCKIT
EF-WM350 MO
BFT50
BFT50CT
LED50
EBT50
WMB50
B42
N/A
N/A
CE50
FSA50
BHA42
LRC12-02
LRC42
WBL
HWK50
CP42
JR50
TH42
RMOTER
WCKIT
EF-WM349 MO
BFT60
BFT60CT
LED60
EBT60
WMB50
B42
C160
C260
CE50
FSA60
BHA42
LRC12-02
LRC42
WBL
HWK50
CP42
JR60
TH42
RMOTER
WCKIT
EF-WM348
BFT72
BFT72CT
LED72
EBT72
WMB72
B42
C160
C260
CE50
FSA72
BHA42
LRC12-02
LRC72
WBL
HWK72
CP42
JR72
TH42
RMOTER
WCKIT
DESCRIPTION
Front Glass
Acrylic Panel
LED Light
Ember Bed Tray
Wall Mounting Bracket
GL Bracket B
GL Bracket C1
GL Bracket C2
Crystal Embers
Flame System Assembly
Blower and Heater Assembly
Remote Control
Circuit Board
LED Backlights
Hardware Kit
Control Panel
Wire Harness
Thermostat
Remote Control Receiver
Wire Cover Kit (Optional)
COMPONENTS
07.17.18
EF-WM373 MO
EF-WM391 MO
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46

Paramount EF-WM391 MO Manuel utilisateur

Marque
Paramount
Modèle
EF-WM391 MO
Catégorie
Cheminées
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents