brondell UF-15 Manuel utilisateur

OWNER’S MANUAL

UC300 Three-Stage Undercounter Water Filtration System

UC100 Single-Stage Undercounter Water Filtration System

North America

1

CONTENTS

Read this Owner’s Manual for correct installation, use and maintenance

of this product. After reading and completing installation, keep this

manual in a place that is easily accessible.

PRODUCT INSTALLATION

09 TVALVE INSTALLATION

10 FAUCET INSTALLATION

12 FILTER HEAD

CONNECTION

ASSEMBLY INSTALLATION

13 INSTALLING THE FILTERS

14 CONNECTING THE TUBING

Using “Quick Connectors”

15 PREPARING FOR USE

GENERAL INFO

02 SAFETY INFORMATION

03 TDS METER INFORMATION

04 FEATURES

05 UC

300

PRODUCT COMPONENTS

06 UC

100

PRODUCT COMPONENTS

07 UC

300

WATER FLOW DIAGRAM

08 UC

100

WATER FLOW DIAGRAM

MAINTENANCE

16 FILTERS & FILTER CHANGE INDICATOR

Filters

Filter Change Indicator

Filter Replacement Cycle

17 REPLACING THE FILTERS

19 TROUBLESHOOTING

TECHNICAL INFO

20 PRODUCT SPECIFICATIONS

21 UC

300/

UC

100

PERFORMANCE DATA SHEET

24 WARRANTY

25 CONTACT BRONDELL

26 SPANISH VERSION

53 FRENCH VERSION

2

SAFETY INFORMATION

Be careful to keep this safety information. Please read this information to

prevent property loss and ensure safety.

DANGER: If not observed, serious injury or even death may occur as a result.

WARNING: If not observed, serious physical injury or property damage may occur as a result.

• Read all the instructions before using or installing the Coral UC300/UC100.

• Never disassemble, repair or reconstruct the lter head housing. This may cause the product

to fail.

• Never unscrew the lters while the product is in use. This may cause failure due to high water

pressure, or it may cause a water leak.

• Do not install near radiators. This may cause re, or the product could be damaged, resulting

• in leakage.

CAUTION: If not observed, minor physical injury or property damage may occur as a result.

• For California Residents: CR2032 batteries contain Perchlorate Material - special handling

may apply. Visit http://www.dtsc.ca.gov/hazardouswaste/perchlorate for more information.

• Use or place the unit on a level area and do not apply force to the unit. This may cause physi-

cal injury and/or damage to the product that may void your warranty.

• Turn the water supply valve o if the lter system will not be used for an extended period

of time.

• Especially during very cold weather, the water pressure may rise and may cause a water leak.

• Replace the lters according to their scheduled replacement intervals. If one or more of the

lters are exhausted, the purication quality will diminish.

• When replacing the lter or moving the product, do not pull on the water supply hose. The

water supply hose may become detached, damaged, or the quick connection coupling may

be weakened.

• If a water leak occurs while using the product, or the area around the product is wet,

• turn the water supply valve o immediately.

3

The Coral Undercounter Water Filtration System is not designed to remove benecial

minerals from your drinking water. These minerals that occur naturally are a healthy

part of your drinking water and should remain. The Brondell Coral Undercounter

Water Filtration System is designed to dramatically reduce water-soluble harmful

contaminants, including industrial chemicals, pesticides, herbicides, turbidity,

volatile organic compounds (VOCs), and microorganisms, most of which cannot be

"read" with a TDS reader.

Since these harmful components are water-soluble, they cannot be picked up by a

simple TDS meter. Contrary to its name (Total Dissolved Solids or TDS Meter), these

inexpensive products cannot detect most harmful water-soluble contaminants.

There is a major misconception that low TDS readings mean healthy water and that

is simply not always true.

The best method for testing the performance of a water ltration device is to have

a nationally recognized independent organization,such as WQA (Water Quality

Association) or NSF International,test and certify the products. The certied data

is then available in a Performance Data Sheet, which you should request from the

manufacturer. For more clarication of what the Coral Undercounter Water Filtration

System does remove from your water, please see our Certied Performance Data

Sheets on pages 21-23.

IMPORTANT NOTE ABOUT

“TDS METERS” AND TESTERS

Q) When I use a Total Dissolved Particle (TDS) reader to test my water

after it goes through the Coral Undercounter Water Filtration System,

why don't the levels of dissolved particles go down or decrease? I don’t

think the product is working.

4

BRONDELL H2O+ CORAL FEATURES

Superior Filtration Performance

Best in class water ltration for a healthy home and family

Elegant Chrome Faucet with Integrated LED

Filter Change Indicator

Simple intuitive LED indicator reminds you when it’s time to change

your lters

Easy Quick Change Filter Replacement

Brondell’s special “twist & seal” lter system makes changing your lters

a breeze

One Year (UC300) or Six Month (UC100) Filter Lifespan

Simplied maintenance and low cost of operation

Easy DIY Installation

Pre-installed faucet tubing and “quick-connect” water supply connections

simplies installation

WQA Gold Seal Certied Filtration Technology

Filtration performance claims you can trust!

One Year Manufacturers Warranty

Backed by Brondell’s commitment to superior customer service

and support

5

UC300 PRODUCT COMPONENTS

Water Supply Tubing

Filter Head

Connection Assembly

3 Filters:

Sediment Filter

Pre-Carbon Filter

Carbon Block Filter

LED Indicator Faucet

Assembly with attached

tubing (blue)

Water Supply T-Valve

with Rubber Washer

(3/8” connection)

T-Valve Adapters

with Rubber Washer

3/8” to 1/2”

Quick Connect

90° Elbows

Mounting Screws

6

UC100 PRODUCT COMPONENTS

Filter Head

Connection Assembly

1 Filter:

Carbon Block Filter

Water Supply Tubing

LED Indicator Faucet

Assembly with attached

tubing (blue)

Water Supply T-Valve

with Rubber Washer

(3/8” connection)

T-Valve Adapters

with Rubber Washer

3/8” to 1/2”

Quick Connect

90° Elbows

Mounting Screws

7

UC300 WATER FLOW DIAGRAM

Sediment

Filter

Pre-Carbon

Filter

Carbon

Block Filter

Incoming

Water

INLET

Filtered

Water

OUTLET

– REAR VIEW –

Tap Faucet

LED Indicator

Faucet

Filtered

Water Tubing

Water Supply

Tubing

Sediment Filter

Sink

Pre-Carbon Filter

Carbon Block Filter

Filter Head Connection

Assembly

Water Supply

T-Valve

Cold Water

Supply

8

UC100 WATER FLOW DIAGRAM

Carbon

Block Filter

Incoming

Water

Filtered

Water

– REAR VIEW –

Tap Faucet

LED Indicator

Faucet

Water Supply

Tubing

Sink

Carbon Block Filter

Filter Head Connection

Assembly

Water Supply

T-Valve

Filtered

Water Tubing

Cold Water

Supply

INLETOUTLET

9

PRODUCT INSTALLATION

STEP 1: TVALVE INSTALLATION

Do not install the Filter Head Connection Asssembly further than 12 feet away from

either the water supply valve, or the Indicator Faucet.

Avoid unnecessary slack in the supply hoses when connecting to the water supply, Filter

Head Connection Assembly, or Indicator Faucet.

Do not install in direct sunlight, or a place where it will be directly exposed to freezing

temperatures.

Be sure to install the T-Valve on the cold water supply line. Running hot water through

the Coral Water Filtration System will damage the lters.

1. Close the cold water supply valve. Place a bucket, or similar

item, underneath the valve to catch any water that may spill

out during installation.

2. Unscrew the hose that connects the cold water supply valve

to the existing tap water faucet.

3. Ensure the rubber washer is inside the T-Valve, and then

screw the T-Valve Adapter onto the cold water supply valve.

NOTE: If the water supply valve is larger than the 3/8”

connection on the T-Valve, use the included 1/2” Valve

Adapters with Rubber Washers to connect the T-Valve and

the water supply hose.

4. Screw the cold water supply hose to the top of the T-Valve.

Be sure to keep the water supply valve closed.

10

STEP 2: FAUCET INSTALLATION

Before Installation

You will need an existing faucet hole at least 7/16

inches in diameter in the sink or countertop to install

the supplied ltered water faucet. You may also

replace an existing kitchen sprayer, soap dispenser,

or plug already on the countertop or sink.

1. Unpack the faucet and insert the Top Spout into the Main

Body by pushing down until inserted then screw the Top Cap

clockwise until secured in place.

2. Cut zip tie on the blue water connection tubing and unroll

to straighten tubing. Be careful not to cut the tube when

removing the zip tie.

If drilling a new hole is required for the

faucet installation, please consult a

professional. Brondell will not be liable

for any damages including those to the

sink or countertop due to installation of

the faucet or drilling a hole.

Please nd answers to Frequently Asked

Questions (FAQs) and installation videos

on brondell.com

For California Residents: CR2032

batteries contain Perchlorate Material -

special handling may apply. Visit http://

www.dtsc.ca.gov/hazardouswaste/

perchlorate for more information.

Locking Nut

Plastic Washer

(raised area faces down)

Top Spout

Top Cap

Main Body

Lock Washer

Counter Top

1/4" Tube

(connected to faucet)

Escutcheon

LED Indicator

Battery Seat

CR2032

Battery

PRODUCT INSTALLATION (cont.)

11

3. Attach the Escutcheon to the Main Body by inserting the blue

tubing through the Escutcheon and pushing it all the way up

until connected to the Main Body.

4. Install the faucet on top of the countertop or sink and feed

the blue tubing through the hole to the cabinet below. Then

slide the large Plastic Washer as shown up through the blue

tubing until snug against the bottom of the countertop or

sink hole.

Be sure that the at part of the Plastic Washer is facing up

and the raised area is facing down, as shown to the right.

5. Install the Lock Washer and the Locking Nut the same way

and tighten until the plastic washer is holding the faucet

assembly rmly in place. The faucet is now installed.

6. Pull the plastic tab out from the battery compartment to

activate the faucet indicator. The LED light will blink red

once, blue once, and then will be ready to go.

**IMPORTANT** Be sure that the at side of the

Plastic Washer is facing up and the raised area is

facing down, as shown below.

RAISED AREA FACES DOWN

FLAT SIDE FACES UP

12

STEP 3: FILTER HEAD CONNECTION ASSEMBLY INSTALLATION

Be sure to install the Filter Head Connection Assembly so that the top of the assembly

is at least 14 inches from the oor of the sink cabinet. Otherwise the lters will not

install or seat correctly.

2. Using a pencil, mark where the Filter Head Connection Assembly will be mounted to the

sidewall of the cabinet (at least 14” from the cabinet oor). Use a level to make sure that the

Assembly will be mounted straight.

NOTE: Before you mount the Connection Assembly, it may be a good idea to practice inserting

and removing the lters.

3. Insert the two mounting screws through the holes in the Assembly frame and screw into the

cabinet sidewall.

1. Attach the two Quick Connect 90° Elbows to back side of the Connection Assembly Inlet and

Outlet as shown

UC300 UC100

PRODUCT INSTALLATION (cont.)

14 inches

13

STEP 4: INSTALLING THE FILTERS

1. To insert the lters, rst line up the arrow on the lter head

with the arrow on the lter

NOTE: For purchasers of the Coral UC300, it is very important to install the lters in the correct

order. Simply match the same label colors to the lter head labels. From left-to-right, the

proper order is

1) Sediment lter

2) Pre-Carbon lter

3) Carbon Block lter

2. With the top and bottom arrows

still lined up, insert the top

of the lter into the housing

and turn 90 degrees to the

right, until the lter will not

turn any more.

The Filter Head arrow should

now be lined up with the “Circle”

icon and notch on the top

of the lter.

3. For UC300 – Repeat the process for the Pre-Carbon lter and Carbon Block lter.

For UC100 – This process is complete.

UC300 UC100

water outlet

water inlet

14

STEP 5: CONNECTING THE TUBING

1. Water Supply Connection

Use the supplied white Water Supply Tubing to connect the T-valve to the Filter Head Connector

Assembly by pushing one end of the tubing rmly into the Quick Connector

Collette on the open side of the T-Valve. Be sure to push in all the way and ensure the Tube

is not bent or kinked.

Then connect the other open end of the Tubing to the Filter Head Connector Assembly “Inlet”

by inserting the tube into the Collette on the Quick Connect 90° Elbow on the side labeled

“Inlet”.

Using "Quick Connectors"

Tube connections on the T-Valve, Filter Head Connection Assembly, and Indicator Faucet are all of

the “Quick Connect” variety. The steps below illustrate how to connect and disconnect the Tubes

from these connectors.

a. Push the Tube into the Collette. The Collette is a collar that

provides a secure t for the Tube and prevents water leaks.

b. Push the Tube in until it stops. The Tube will be secure, and

resistant to tugs or pulls. The Collette will be rigid and raised

slightly from the connector housing.

c. To disconnect the Tube, push down and hold the Collette rst,

and then pull the Tube out gently.

2. Faucet Connection

Now, connect the open end of the Blue Tubing coming from the Faucet to the Filter Head

Connector Assembly “Outlet” by inserting the Tube into the Collette on the Quick Connect 90°

Elbow on the side labeled “Outlet”. Be sure to push in rmly all the way and ensure the Tube is

not bent or kinked.

Connector

Housing

Tube

Collette

a

c

b

Visit brondell.com for our Quick Connect Tutorial video.

PRODUCT INSTALLATION (cont.)

15

PREPARING FOR USE

TURN ON WATER & CHECK FOR LEAKS

FLUSHING THE SYSTEM

1. Turn on water supply

a. Open the T-Valve by turning the valve arm 90° as shown.

b. Turn the cold water supply valve at the wall counter-

clockwise to turn on. The cold water supply will then

begin to supply water to the Coral UC300 or UC100.

2. Checking for leaks

a. Once the water supply has been turned on, check for any

signs of leaking throughout the system.

b. If no leaks are found, wait 5 minutes and check one more

time. If still no leaking, then continue to next step to ush

the system.

1. Turn the Indicator Faucet on and let the water ow from the faucet for 5 minutes continuously to

ush the system and activate the lter(s).

2. Check one last time for any leaks during this process.

3. Your Coral system is now ready to use!

Before turning the cold water valve back on, review the installation instructions to

ensure that the T-Valve and water hoses are connected correctly and securely.

Failure to properly install this product or to properly check for leaks may cause damage

to the property. In these instances, Brondell, Inc. will not be held responsible for any

damages.

16

FILTERS

FILTER CHANGE INDICATOR

FILTER REPLACEMENT CYCLE

Contact Brondell at 888-542-3355, or visit us at www.brondell.com to order replacement lters.

The lters are critical to the performance of the Coral UC Water Filtration system, and it is

important to replace all of the lters on a regular basis. If any of the lters are overused beyond the

recommended service life, the performance of the water ltration device can deteriorate. Do not

miss the lter replacement cycle or use non-compatible lters as this can aect system performance

or damage the unit.

The LED lter change indicator in the faucet works by tracking both time and water ow from the

Coral UC system.

UC300 – When 12 months have elapsed or 600 gallons of water has been ltered through the system

(whichever comes rst), the LED will ash red when dispensing water instead of ashing blue.

UC100 – When 6 months have elapsed or 300 gallons of water has been ltered through the system

(whichever comes rst), the LED will ash red when dispensing water instead of ashing blue.

When the faucet LED indicator begins to ash red, it’s now time to change the lters and reset the

faucet indicator by replacing the battery.

A new battery is always included with the UF-35, or UF-15 lter replacement set.

* The lter replacement frequency may be increased for areas with poor water quality or

greater use. The period for the lter exchange is based on an average production of 1.64

gallons of drinking water per day.

FILTERS & FILTER CHANGE INDICATOR

Part Number Filter Name Usable period*

UF35

Sediment Filter 12 months

Pre-Carbon Plus Filter 12 months

Carbon Block Filter 12 months

UF-15 Carbon Block Filter 6 months

UC300

UC100

17

MAINTENANCE

REPLACING THE FILTERS

1. Close the T-Valve under the sink to shut o the ow of water

to the Coral.

2. Once the T-valve is shut o, turn the Indicator Faucet on all

the way and keep it on until all the residual water in the

tubes has been expelled.

4. Install the new lter(s). Review the procedure outlined on Page 13.

5. Open the T-Valve to restore the ow of water and turn the Indicator Faucet on for 5 minutes

continuously to ush and activate the new lter(s).

Be sure to reset the Indicator Faucet by following the next steps.

3. Turn the lter(s) to be replaced 90° to the left, until the lter

comes out of the Filter Head Connection Assembly.

For UC300, remove the remaining two lters.

For UC100, the process is complete.

18

6. Replace the battery in the faucet LED indicator to reset

the lter change reminder. The battery type is CR2032

and Brondell provides one with every set of UF-35 and

UF-15 lters.

a. Under the faucet handle, locate the black rubber battery

compartment. Grasp it from the sides and pull down as

shown.

b. Remove the old battery from the compartment by lifting

the silver metal tab and sliding the battery out of the

rubber casing. Wait 30 seconds for the residual energy to

drain to reset the indicator.

c. Replace with a new CR2032 battery by sliding the battery

under the silver tab, making sure that the words on the

battery are facing out. A fresh CR2032 battery comes with

every UF-35 and UF-15 Replacement Filter pack.

d. Push the black rubber battery compartment back up into

the faucet handle.

e. The indicator will blink red once, blue once, and then the

indicator will function as normal.

MAINTENANCE (cont.)

REPLACING THE FILTERS (cont.)

La page charge ...

brondell UF-15 Manuel utilisateur

Ce manuel convient également à

brondell UF-15 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents