Maytag MFC2061HES - 20 cu. Ft Mode d'emploi

I , ,M_7 YrAG

French Door

, ,

......................................J,_r"

,,,,,,,,,,,,.........................................................

0

r/

g e .............

Important Safely

Instructions .................................... 1=2

Installation ..................................... 3-9

Temperature Controls .............. 10-12

Fresh Food Features ................ 13-15

Freezer Features ............................. 15

Ice And Water ................................... 1 Ii

........i...........................

Water Filter .................................. 17=18

Food Storage Tips .................... 19-21

Care and Cleaning ................... 22=25

Operating Sounds .......................... 20

Troubleshooting ........................ 27=29

Warranty & Service ........................ 31

Guide d'utilisation et

d'entretien ........................................ 32

Gufa de Usa y Cuidado ................. 64

Form No. A/O_/06 Parl No. i 282810_ www.may{.ag.com c 2000 Mayiag Appliances Sales Co. Lid_a U.S.A.

ImportentSefet¥Instructlons

Instafler: Please leave ths guide with ths apphance.

Consumer: Please read and keep th_s Use and

Care Guide for future reference; it provides tile

proper use and maintenance reformation.

Keep sales receipt and/or canceled check as proof

of purchase.

Call: 1-800-688-9900 U.S.A.

1-800-688-2002 Canada

1-800-688-2080 (U.S. TTY for heanng or

speech impaired)

(Mon.-Fn., 8 am-8 pm Eastern Tu_e)

Have complete model and senal number

identification of your refngeratoL ThB is located on a

data plate ms,de the fresh food compartment, on the

upper right side. Record these numbers below for

easy access.

Model Number

Serial Number

Date of Purchase

In our continuing effort to n_prove the quahty and

performance of our apphances, it may be necessary

to make changes to the apphance without revising

ths gLHde.

What You Need to Know About

Safety Instructions

Warning and In]portant Safety Instructions appeanng in

this guide are not meant to cover all posstble

condittons and sttuations that may occur. Common

sense, caLitlon and care mLISt be exercised when

installing, maintaining or operating apphance.

Always contact your dealer, distributor, service agent or

manufacturer about problems or conditions you do not

understand.

Recognize Safety Symbols, Words,

Labels

DANGER - Immediate hazards which WILL result

m severe personal injury or death.

WARNING - Hazards or unsafe practices which

COULD result in severe personal injury or death.

CAUTION - Hazards or unsafe practices which COULD

result 101minor personal injury or propelty damage.

To reduce risk of injury or death, follow basic

precautions, including the following:

IMPORTANT: Child entrapment and suffocation

are not problems of the past. Junked or abandoned

refrigerators are still dangerous - even if they sit out

for "'just a few days:' If you are getting nd of your old

refrigerator, please follow the instructions below to

help prevent accidents.

Before you throw away your old

refrigerator or freezer:

, Take off the doors.

. Leave the shelves in place so

children may not easily chmb

reside.

This appliance is equipped with a three-prong

grounding plug for your protection against possible

electncal shock hazards. It must be plugged into a

grounding receptacle. Where a standard two-prong

wall receptacle is encountered, it is the personal

responsibility and obhgation of the customer to have it

replaced with a properly grounded three-prong wall

receptacle. Do not under any circumstances, cut or

remove the third (ground} prong from the power cord.

Do not use an adapter plug.

Power supply cord with

three-prong grounding plug

Grounding type

wall receptacle

Importent$efet¥Instructlons

To reduce risk of fire, electric shock, serious

injury or death when using your refrigerator,

follow these basic precautions, including the

following:

1. Read all instructions before using the refrigerator.

13.

not attempt service if instructions are not under-

stood or if they are beyond personal skill level.

Always dBconnect refrigerator from electrical

supply before attempting any service. DBconnect

power cord by grasping the plug, not the cord.

2. Observe all local codes and ordinances.

3. Be sure to follow grounding instructions.

4. Check with a qualified electrician if you are not

sure thB apphance msproperly grounded.

5. Do not ground to a gas line.

6. Do not ground to a cold-water p_pe.

7. Refrigerator is designed to operate oil a separate

115 volt, 15 amp., 60 cycle ime.

8. Do not modify plug on power cord. If plug does

not f_t electrical outlet, have proper outlet installed

by a qualified eJectnclan.

9. Do not use a two-prong adapter, extension cord

or power stnp.

10. Do not remove warning tag from power cord.

11. Do not tamper w_th refrigerator controls.

12. Do not service or replace any part of refrigerator

unless specifically recommended in Use & Care

GLnde or pubhshed user-repair instructions. Do

14.

15.

16.

17.

18.

19.

20.

Install refngerator according to Installation

Instructions. All connections for water, electncal

power and grounding must comply with local

codes and be made by hcensed personnel when

required.

Keep your refrigerator in good condition. Bumping

or dropping refrigerator can damage refngerator

or cause refrigerator to malfunction or leak. If

damage occurs, have refrigerator checked by

qualified service technician.

Replace worn power cords and!or loose plugs.

Always read and follow manufacturer's storage

and _deal environment instructions for _tems being

stored in refngeratol:

Your refngerator should not be operated In tile

presence of explosive fumes.

Children should not chmb, hang or stand on any

part of tile refrigerator.

Clean up spills or water leakage associated with

water mstallatmon.

SAVE THESE iNSTRUCTiONS

Your refrigerator was packed carefully for shipment.

Remove and discard shelf packaging and tape. Do not

remove the serial plate.

Leveling

Location

* Do not install refrigerator near oven, radiator or other

heat source. If not possible, shield refrigerator with

cabinet material.

* Do not install where temperature falls below 55° F

(13° C) or rises above 110° F (/43° C). Malfunction may

occur at this temperature.

• Refrigerator is designed for indoor household

application only.

Measuring the Opening

When installing your refrigerator, measure carefully.

Allow '/;' space at top and '/_"space behind the machine

compartment cover (located in the rear) for proper air

circulation.

Subflooring or floor coverings (i.e. carpet, tile, wood

floors, rugs) may make your opening smaller than

anticipated.

Some clearance may be gained by using the leveling

procedure under Leveling.

Important: If refrigerator is to be installed into a recess

where the top of the refrigerator is completely covered,

use distance from floor to top of hinge cap to verify

proper clearance.

Transporting Your Refrigerator

• NEVER transport refrigerator on its side. If an upright

position is not possible, lay refrigerator on its back.

Allow refrigerator to sit upright for approximately 30

minutes before plugging it in to assure oil returns to

the compressor. Plugging the refrigerator in

immediately may cause damage to internal parts.

• Use an appliance dolly when moving refrigerator.

ALWAYS truck refrigerator from its side or

back-NEVER from its front.

• Protect outside finish of refrigerator during transport

by wrapping cabinet in blankets or inserting padding

between the refrigerator and dolly.

• Secure refrigerator to dolly firmly with straps or

bungee cords. Thread straps through handles when

possible. Do not overtighten. Overtightening restraints

may dent or damage outside finish.

To enhance the appearance and maintain performance,

the refrigerator should be level.

Note

• Complete any required door reversal, panel

installation and/or a water supply connection,

before leveling.

Materials Needed:

* 3/8"hex head driver

* Carpenter's level

1. Remove toe grille.

* Grasp firmly and pull outward

to unclip.

2. Remove bottom hinge cover(s).

• Place the eraser end of a pencil or similar blunt

tool in the cover notch.

Notch

Location

• Use slight pressure to pry the

cover loose.

• Continue to maintain

downward pressure to the

notched side of the cover while

swinging it off.

3. Using hex head driver, turn the front adjustment

screws (A) on each side to raise or lower the front

of the refrigerator.

C C

Note

• Some models only have adjustment screws '_"

4. Using the hex head driver, turn each of these

adjustment screws (B) to raise or lower the rear of

the refrigerator.

5. Using the carpenter's level, make sure front of

refrigerator is '/_"(6 ram) or Yzbubble higher than

back of refrigerator and that the refrigerator is level

from side to side.

6. Turn stabilizing legs (C) clockwise until firmly

against floor.

7. Turn adjustment screws (A) counterclockwise to

allow the full weight of the refrigerator to rest on

the stabilizing legs.

8. Replace hinge cover(s).

• Position cover into the outer edge of the hinge.

• Swing the cover toward the cabinet and snap it

into place.

9. Replace the toe grille.

Note

• For proper reinstallation, ensure the "top" marking

on the interior of the toe grille is oriented correctly.

• Align the toe grille mounting clips with the lower

cabinet slots.

• Push the toe grille firmly until it snaps into place.

Door and Drawer Removal

Some installations require door/drawer removal to

transport the refrigerator to its final location.

z

N

n_

.

2.

Unplug power cord from power source.

Remove toe grille and bottom hinge

cover(s) (see page 3).

Remove top hinge cover from

refrigerator door by removing Phillips

screw and retain screw and cover for

later use.

Unscrew -_,_"hex head screws from

top hinge to remove hinge and retain

all screws for later use.

Lift right side refrigerator door from = °

center hinge pin. Remove door

closure from center hinge pin on

the right side and retain for later right

side

use. _ door

closure

Disconnect wire harness on top

of left side refrigerator door top

hinge.

Release two-pin connector by

pressing junction point with a

flat blade screwdriver or

fingernail.

Green ground wire remains

attached to the hinge.

Unscrew t,_" hex head screws from

top hinge to remove hinge and retain

for later use.

Lift left side refrigerator door, along

with top hinge, from center hinge pin.

Remove center hinge pin with a 5/,,,

hex head driver and retain hinge pin

for later use.

Remove Phillips screws to remove

right and left hinges and retain all

screws for later use.

Remove both stabilizing brackets

with _/8"hex head driver and retain

screws for later use.

Pullout Freezer Drawer

Cselect models)

To Remove:

1. Pull drawer open to full

extension.

2. Tilt the lower basket

forward and lift to remove.

. On each white drawer

bracket is a basket cradle

with two snap

attachments. To release

each cradle, unlatch the

snaps by pushing them

inward, away from the

side bracket. Lift the

cradles off of the rails.

4. Remove Phillips screw

from each of the drawer

slides (select models).

5. Lift top of drawer front

to unhook the drawer

from the slides. Lift

door front out to

remove.

To Install:

1. Pull both rails out to

full extension.

2. While supporting

door front, hook

supports into slots

located on inside of

each slide.

Note

• All four drawer bracket supports must be in the

proper slots for the drawer to function properly.

3. Lower door front into final position.

4. Replace and tighten Phillips screws that were

removed from the drawer slides (select models:).

6. Tilt the lower basket front down and set it down

into the basket cradles.

Basket cradle

snap attachments

5. Place the basket cradles back onto the drawer

slides. Align basket cradle snaps with the slots on

the drawer brackets and press each cradle

towards the bracket until it clicks.

Door Reinstallation

1. Install hinge assemblies:

• Install center hinge with Phillips screws.

2. Place hinge side of refrigerator door on center

hinge pin.

• Install top hinge with 5/,,, hex head

sorews.

3. While holding refrigerator door

upright, tighten down top hinge

with 5/,6"hex head driver.

4. Reconnect two-pin connector.

5. Replace top hinge covers.

Handles

If not installed, the handle is located in the interior of

the fresh food section or attached to the back of your

refrigerator.

Remove and discard handle packaging and tape.

Front Mount Handle

Materials Heeded:

• Gloves to protect hands

• Phillips screwdriver

• Plastic door removal card [or '_2"thick plastic card:},

retain the card

Attach Extensions to Handle:

1. Align handle and

extension as shown.

/J

2_

3_

ZIt_

Place extension in

handle opening.

Apply slight pressure

to both sides of the extension piece.

Slide extension until it stops on inside edge of

handle.

To Install:

1. The handles are to be oriented

as shown.

2. Align front mount door handle

clip with the door tabs.

3. Ensure the handle clips are

positioned slightly above the

door tabs.

4. Rotate the handle so that the

handle is flat against the door.

5. Push the handle down against the

upper door tab just enough to

allow it to hang unsupported.

!

i

6. Align bottom of handle with lower

door tab. Press upper handle end to

door surface and firmly grasp lower

end of handle. Gently slide handle

upward until bottom of handle

settles on door surface, then

reverse direction, sliding downward

to almost engaging tab with clip. .-

7. Grasp the handle firmly and slide

down until it clicks. The audible _

click indicates fastening clips are _

securely interlocked.

_,

To Remove:

1. Flex the handle away from the door

panel. Simultaneously place door

handle removal card underneath

the base of the lower handle. Insert

the card to the line or until it stops.

2. Grasp the lower part of the handle

firmly and lift to remove.

die

_Door

Tab

Freezer Handle

Materials Needed:

• Gloves to protect hands.

• Phillips screwdriver.

• Plastic handle removal card (or '/32"thick plastic

card). Retain the card.

Notes

• There is a slight curve to

the freezer handle.

• For proper installation, be

sure handle is oriented as

shown.

To

1.

2_

3_

engagement. Then firmly slide the handle to the

right until it clicks. The audible "click" indicates

that the fastening clips are securely interlocked.

_emove:

At the right end, flex the handle base away from

the surface of the freezer drawer. Simultaneously

slide the door handle removal card that came with

your refrigerator under the right side base of the

handle. Slide the card to the line indication or until

it stops, which will be approximately 1'/;'.

With both hands, firmly grasp the handle towards

the right base.

Slide towards the left, lift and remove from the

surface.

To install:

1. Align door handle clips slightly to the left of the

tabs attached to the freezer door.

2. Rotate the handle so the left base is flat against

the door.

Push the left handle

base against the left

door tab and slightly

to the right, just

enough to allow it to

hang unsupported.

While firmly supporting the left handle base against

the door, align the right base of the handle with the

right tabs that are attached to the door.

Now, while firmly holding the handle at the left and

right bases, gently slide the handle towards the

right until the right base settles in. The handle

should now be flat against the face of the freezer

door at both the left and right bases.

With hands still firmly keeping the handle flat

against the freezer door, you may have to reverse

directions momentarily to assure clip/tab

Installing Front=Mounted Handles for

Stainless Steel Doors

1. Loosen lower door clip on door with

a phillips screwdriver.

2. Locate predrilled hole at base of

handle, and fit hollow end of

handle over lower door clip.

3. Fit other end of handle over upper

door clip and slide up as far as

possible.

NOTE: If top of handle does not fit

over top clip, loosen lower clip

further until fit can be

accomplished.

4. Insert phillips screwdriver into

predrilled hole at base of handle

to tighten screw. Insert plastic

button plug into hole.

5. Repeat above steps to install

other handle.

iiii :i i!!iiii iii

Removing Front=Mounted Handles for

Stainless Steel Doors

/-

1. Remove plastic button plug at base /-_

of handle with a very small fiat-blade

screwd river.

Insert phillips screwdriver into

predrilled hole to remove screw.

2. Slide handle down and remove

from door clip.

3. Repeat above steps to remove

other handle.

Removing Front=Mounted Handles for

Stainless Steel Freezer Door

1. Remove right side plastic button

plugs at each end of handle

with a very small fiat-blade

screwd river.

Insert phillips screwdriver

into predrilled hole to remove

screw.

2. Slide handle right and

remove from door clip. \

Installing Front=Mounted Handles for

Stainless Steel Freezer Door

1. Loosen lower door clip on door

with a phillips screwdriver

2. Locate predrilled hole at base of

handle, and fit hollow end of

handle over left door clip.

\

3. Fit other end of handle over

left door clip and slide left as

far as possible.

NOTE: If end of handle does _\

not fit over left clip, loosen

right clip further until fit can

be accomplished.

4. Insert phillips screwdriver

into predrilled hole at end of

handle to tighten screw.

Insert plastic button plug into

hole.

Connecting the Water Supply

cont.

MaterialsNeeded:

• '/4"outer diameter flexible copper tubing

• Shut-off valve (requires a '/4" hole to be drilled into

water supply line before valve attachment)

• Adjustable wrench

• '/_"hex nut driver

Notes

• Use copper tubing only for installation. Plastic is

less durable and can cause damage.

• Add 8' to tubing length needed to reach water

supply for creation of sewice loop.

2_

3.

Create service loop with copper 2' diameter

tubing (minimum 2' diameter), minimum

Avoid kinks in the copper tubing /_r_

when bending it into a service

loop. Do not use plastic tubing. /_

Remove plastic cap from water valve inlet port. o_o

Place brass nut (A) and sleeve (B) on _

copper tube end as illustrated. A B

Renlinder: Do not use an old __

sleeve. The nut and sleeve are

provided in the use and care packet. -:: _

4. Place end of copper tubing into water

valve inlet port. Shape tubing slightly. Do

not kink - so that tubing feeds straight

into inlet port.

5. Slide brass nut over sleeve and screw nut

into inlet port. Tighten nut with wrench.

zi:°

iMPORTANT: Do not overtighten. Cross

threading may occur.

Pull on tubing to confirm connection is

secure. Connect tubing to frame with

water tubing clamp (C) and turn on

water supply. Check for leaks and

correct if necessary. Continue to

observe the water supply connection

for two to three hours prior to moving

the refrigerator to its permanent

location.

............i!ii!i!iiiiiiiiiiiii!ii!ii!!i

7. Monitor water connection for 24 hours. Correct

leaks, if necessary.

Opening and Closing Your

Fresh Food Doors

Your new refrigerator is

uniquely designed with two

fresh food doors. Either door

can be opened or closed

independently of one another.

There is a vertically-hinged

section on the left fresh food

door. When the left door is

closed, the hinged section

automatically forms a seal

between the two doors when

both doors are closed.

When the left door is opened,

the hinged seal automatically folds inward so that it is

out of the way.

TemperatureControls

Touch Temperature Controls

The controls are located at the top front of the

refrigerator corn partment.

Control

Initial Control Settings

After plugging the refrigerator in, set the controls.

• Pressing the _or D pads adjusts the controls to

the desired setting.

• The temperature control range for both

compartments is 1 through 7 (coldest).

• Initially set the refrigerator control on 4.

• Initially set the freezer control on 4.

• Let the refrigerator run at least 8 to 12 hours before

adding food.

Warm Cabinet Surfaces

At times, the front of the refrigerator cabinet may be

warm to the touch. This is a normal occurrence that

helps prevent moisture from condensing on the

cabinet. This condition will be more noticeable when

you first start the refrigerator, during hot weather and

after excessive or lengthy door openings.

Adjusting the Controls

24 hours after adding food, you may decide that one

or both compartments should be colder or warmer. If

so, adjust the control(s) as indicated in the

Temperature Control Guide table below. See page 19

for instructions on checking compartment

temperature.

Except when starting the refrigerator, do not change

either control more than one number at a time.

* Allow 24 hours for temperatures to stabilize.

Changing either control will have some effect on the

temperature of the other compartment.

Temperature Control Guide

Refrigerator too warm

Refrigerator too cold

Freezer too warm

Freezer too cold

Turn refrigerator OFF

Set the refrigerator control

to next higher number by

pressing the D pad.

Set the refrigerator control

to next lower number by

pressing the G pad.

Set the freezer control to

next higher number by

pressing the _ pad.

Set the freezer control to

next lower number by

pressing theG pad.

Press the refrigerator or

freezer _ pad until a dash

(-) appears in the display.

Energy Saver Switch [select models)

Off - The refrigerator uses more energy when this

switch is off, because a heater located in the hinged

seal section of the door is running. This heater helps

prevent condensation formation on the exterior of the

hinged seal. Turn the energy saver switch OFF when

the environment is warm and more humid or if

moisture is noticed on the door exterior.

• On - This setting saves energy by not using the

heater. Turn the energy saver switch ON when the

environment is less humid.

10

fempereture

11

Triple Cool Climate Control

(select models)

The control is located at the top front of the fresh food

compartment.

Control

0 0 G 0 0 0

Initial Temperature Setting

Temperatures are preset at the factory at 38 ° F (3° C)

in the fresh food compartment and 0° F (-18 ° C) in the

freezer compartment.

Adjusting the Control

24 hours after adding food, you may decide that one or

both compartments should be colder or warmer. If so,

adjust the control as indicated in the Temperature

Control Guide below.

• The first touch of the _-_ or _-_b pads shows the

current temperature setting.

The display will show the new setting for

approximately three seconds, and then return to the

actual temperature currently within that

compartment.

* Do not change either control more than one degree

at a time. Allow temperature to stabilize for 24 hours

before making a new temperature adjustment.

Temperature Control Guide

Refrigerator too cold

Refrigerator too warm

Freezer too cold

Freezer too warm

Turn refrigerator OFF

Set the refrigerator control

to next higher number by

pressing the _+_ pad.

Set the refrigerator control

to next lower number by

pressing the _-_ pad.

Set the freezer control to

next higher number by

pressing the _ pad.

Set the freezer control to

next lower number by

pressing the __z_pad.

Press the freezer _+_ pad

until OFF appears in the

display. Press either the

freezer or refrigerator _-_

pad to turn back on.

Speed Ice 0

When activated, Speed Ice reduces the freezer

temperature to the optimum setting for 2/4hours in

order to produce more ice. Note: When the Speed

Ice feature is in operation, the _ and _z_ pads for

the freezer control will not operate.

Reset Filter (select models)

When a water filter has been installed in the

refrigerator, the yellow Order light will illuminate when

90 percent of the volume of water for which the filter is

rated has passed through the filter OR 11 months have

elapsed since the filter has been installed.

The red Replace light will illuminate when the rated

volume of water has passed through the filter OR 12

months have elapsed since the filter was installed. A

new filter should be installed immediately when the

Replace light is illuminated.

After replacing the filter, press and hold the Reset

Filter pad for three seconds. The Order and Replace

lights will go off.

Vacation Mode O

The Vacation Mode feature causes the freezer

to defrost less frequently, conserving energy. The

Vacation Mode indicator light will illuminate when the

feature is activated. To deactivate, press the Vacation

Mode pad again OR open either door. The indicator

light will go off.

Notes

* Door openings will not deactivate Vacation Mode

for approximately one hour after activation.

. If vacationing for more than a few days, see the

Preparing for Vacation section, page 25.

Temp Alarm

The Temp Alarm system will alert you if the

freezer or fresh food temperatures exceed normal

operating temperatures due to a power outage or

other event. When activated, the Temp Alarm light will

illuminate.

fempereture

If the freezer or fresh food temperatures have

exceeded these limits, the display will alternately show

the current compartment temperatures and the highest

compartment temperatures reached when the power

was out. An audible alarm will sound repeatedly.

Press the Temp Alarm pad once to stop the audible

alarm. The Temp Alarm light will continue to flash and

the temperatures will alternate until the temperatures

have stabilized.

To turn off Temp Alarm, press and hold the Temp

Alarm pad for three seconds. The indicator light will

go off.

Door Alarm

The Door Alarm will alert you when one of

doors has been left open for five continuous minutes.

When this happens, an audible alarm will sound every

few seconds until the door is closed OR the Door

Alarm pad is pressed to deactivate the feature.

Max Cool

When activated, Max Cool causes the fresh

food and freezer temperatures to drop to the minimum

settings on the control. This cools down the

refrigerator and freezer after extended door openings

or when loading the refrigerator or freezer with warm

food. Note: When the Max Cool feature is in

operation, the _$_ and _-_ pads for the refrigerator

and freezer controls will not operate.

To activate, press the Max Cool pad. Max Cool will

deactivate automatically after 12 hours, OR press the

Max Cool pad to deactivate the feature.

User Preferences

Access the User Preferences menu to:

• Activate or turn off Super Cool (select models)

• Change the temperature display from °F to °C

• Enable or disable audible alarms.

• Adjust the light level at which the Dispenser Auto

Light will illuminate (when this feature is activated on

the ice and water dispenser) (select models)

• Activate the Sabbath Mode

To access the User Preferences menu, press and hold

the Door Alarm pad for three seconds. When in the

User Preferences mode, a short title for the feature will

appear in the Freezer temperature display and the

feature status will appear in the Fresh Food display.

1. Use the Freezer up and down control to scroll

through the features.

2. When the desired feature is displayed, use the Fresh

Food up and down control to change the status.

3. When changes are complete, press the Door Alarm

pad for three seconds OR close the Fresh Food door.

Super Cool (CO] [seJect models)

When Super Cool is ON, an air-mixing fan in the fresh

food compartment is activated to improve air flow and

temperature control. To save energy, this feature may

be deactivated by choosing OFE

Temperature Display [F_C)

Change the display to show temperatures in degrees

Fahrenheit or degrees Celsius.

Alarm (AL]

When the Alarm mode is OFF, all audible alarms will be

disabled until the feature is turned on.

Auto Light Level Selection (LL) (select models)

This setting adjusts the light level at which the

dispenser light will illuminate when the sensor detects

that the light levels in the room are low. Setting 1 is

the darkest light level setting, setting 9 is the lightest

light level setting. Note: The Auto Light (select

models) must be activated on the ice and water

dispenser control to take advantage of this option.

Sabbath Mode (SAB)

When the Sabbath Mode is ON, all control lights and

the night light will be disabled until the feature is

turned OFE This feature does not disable the interior

lights. Press any pad to restore the control lights.

Warm Cabinet Surfaces

At times, the front of the refrigerator cabinet may be

warm to the touch. This is a normal occurrence that

helps prevent moisture from condensing on the

cabinet. This condition will be more noticeable when

the refrigerator is first started, during hot weather and

after excessive or lengthy door openings.

12

FreshFoodFemres

Shelves

Your refrigerator has Spill-Catcher TM Glass Shelves.

The shelves have a spill retainer edge which allows for

easier clean up and some are equipped with a slide

out feature. To slide out, grasp the front of the shelf

and pull forward. Push in the shelf to return to the

original position.

To Remove a Shelf:

Slightly tilt up the front and lift up

the rear of the shelf, then pull the

shelf straight out.

To Lock the Shelf into Another

Position:

Tilt up the front edge of the shelf.

• Insert the hook into the desired frame openings and

let the shelf settle into place.

• Be sure the shelf is securely locked at the rear.

Elevator TM Shelf ([select models_)

The Elevator TM Shelf is equipped with a spill-retaining

edge and the EasyGlide TM slide-out feature. It can be

adjusted up or down without unloading.

To Slide Out Elevated MShelf:

• Grasp the front of the shelf and pull forward.

• Push the shelf in to return to original position.

To Adjust the Elevator TM Shelf:

• Pull out the knob on the crank handle.

• Rotate the crank clockwise to raise the shelf, and

counterclockwise to lower the height of the shelf.

To Remove Elevator TM Shelf:

• Completely unload the shelf and pull the shelf

forward.

Pull until the shelf stops.

Press up on the tabs located underneath its outside

edges and continue pulling forward until the shelf is

clear of the frame.

To Replace Elevator TM Shelf:

• Align the shelf to the frame and push it all the way

back. It is not necessary to press up on the tabs for

reinstallation.

in ordinary use, the Elevatoff MShelf frame assembly

does NOT require removal. Though unlikely, and not

recommended, the correct removal procedure is as

follows:

To Remove Frame Assembly:

• Unload the shelf completely.

• Slide the shelf forward about 2" and manually move

the two rear latches toward the shelf center.

While supporting the entire shelf and frame from

underneath, lift slightly and rotate the assembly

approximately 30° to allow the rear mechanism to

clear the vertical rear side rails.

• The entire assembly can then be moved forward

and clear of the refrigerator compartment.

To Reinstall Frame Assembly:

• Reverse the removal procedure. Be sure the shelf

is in a level position. When the sliding shelf is

pushed to the rear, it will reposition the rear latches

to their correct operating position.

(style may vary)

Frame Assembly

Slide Out Shelf

13

The Crisper Top serves as the lower fresh food shelf.

To Remove the Crisper Top:

• Remove crisper drawers.

• Place hand under the frame to push up the glass. Lift

glass out.

• Lift frame from refrigerator liner rails.

To install:

• Replace frame in refrigerator liner rails.

• Carefully replace glass into frame.

Door Storage

Dairy Center

The Dairy Center provides

convenient door storage for

spreadable items such as butter

and margarine. This compartment can be moved to

different locations to accommodate storage needs. To

use the dairy center, raise the cover.

To Remove:

• Raise the cover, pull upward and tilt out.

To Install:

• Slide the Dairy Center in and down until firmly seated

in the door liner.

Door Buckets

Door Buckets can be moved to meet storage needs.

To Remove:

• Slide bucket up and pull straight out.

To Instaih

• Slide bucket in and down until

firmly seated in the door liner.

Crisper Drawers

The Crisper Drawers provide a higher humidity

environment for fresh fruit and vegetable storage.

Controls

The Crisper Controls regulate the amount of humidity

in the crisper drawee Slide the control toward the

FRUIT setting for produce with outer skins. Slide the

control toward the VEGETABLES setting for leafy

produce.

VEGETABLES FRUIT

HUMIDITY CONTROLLED

To Remove:

* Pull drawer out to full extension. Tilt up front of

drawer and pull straight out.

To install:

• Insert drawer into frame rails and push back into

place.

Note

• For best results, keep the crisper drawers tightly

closed.

Temperature=Controlled Drawer

The Wide-N-Fresh TM drawer is a full-width drawer

with adjustable temperature control. This drawer can

be used for large party trays, dell items, beverages or

miscellaneous items and features a divider to organize

the drawer into sections if desired.

There is a temperature control which adjusts the

amount of cold air allowed into the drawer. The

control is located on the right side of the drawer, under

the lid.

Set the control to the higher setting _ to provide a

normal refrigerator temperature. Set the drawer on the

Iowersetdng _ when a temperature colder than

the main refrigerator compartment is desired. Use the

coldest setting when storing meats.

Notes

• Cold air directed to the drawer can decrease

refrigerator temperature. Refrigerator control may

need to be adjusted.

• Do not place leafy vegetables in the drawer.

Colder temperatures could damage leafy produce.

To Remove Drawer:

• Lift lid. Pull drawer out to full extension. Tilt up front

of drawer and pull straight out.

To install Drawer:

• Push metal glide rails to the back of the refrigerator.

Place drawer onto rails and slide drawer back until it

falls into place.

continued

14

FreshFoodFemres

To Remove Divider:

• Pull drawer completely out and raise the front of the

divider to unhook it from the rear wall of the drawer

and lift it out.

To Install Divider:

• Hook back of divider over rear wall of drawer and

lower into place

Accessories

Egg Tray

[style may vary/select models_)

The Egg Tray holds a "dozen-

plus" eggs. It can be removed

to carry to a work area or to

be washed.

Wine Trivet/Can Rack [select models_)

The Wine Trivet/Can Rack accessory fits in the

Wide-N-Fresh TM drawer or on a shelf.

Bottles or cans can be laid

crosswise, or a single bottle may

be laid in the center depression.

Upper Wire Basket

To Remove:

• Pull upper basket out to full extension and lift out to

remove.

To install:

• Slide upper basket

into freezer. Make

sure that rear of

basket hooks behind

rail catch.

Note

. Lower Freezer Drawer: See page 5 for lower

basket and complete pullout drawer instructions.

Accessories

ice Bin

The Ice Bin provides

storage for ice.

J

15

Automatic ice Maker

Connect the ice maker to the water supply as

instructed on pages 8-10. Proper water flow and a

level refrigerator are essential for optimal ice

maker performance.

Operating Instructions

• Conflml ice bm is m place and ice maker arm is

down.

• After freezer section reaches between 0° to 2° F (-18 °

to -17 ° C), ice maker fills with water and begins

operating. You will have a complete

harvest of ice approxmlately every

three hours.

• Allow approxHllately 24 hours after

installation to receive first harvest of

ice.

• DBcard _cecreated withH1 first ] 2 hours of operation

to assure system is flushed of mlpunties.

• Stop ice production by raising ice maker arm until

click is heard.

• Ice maker will remain Ill the off position until arm is

pushed down.

• The first one or two batches will probably contain

undersEed and irregular cubes because of all Ill the

supply lille.

• When the ice cubes are ejected it is normal for

several cubes to be joined together at the ends. They

can easily be broken apart. The ice maker w_ll

continue to make ice until the supply of ice cubes

raises the ice maker arnl, shuttHlg the ice maker off.

• Certain sounds may accompany the various cycles of

the ice maker. The motor may have a shght hun], the

cubes will rattle as they fall into all empty storage

pan and the water valve may click or "'buzz"

occasionally.

• If the ice is not used frequently, the ice cubes will

become cloudy, shrink, stick together and taste stale.

Empty the ice storage bin periodically and wash it in

lukewarm watel: Be sure to dry the bin thoroughly

before replacing it.

• Beverages and foods should not be placed in the ice

storage bin for quick chllhng. These items Call block

the Ice maker arm, causing the ice maker to

Ill alfu nctlo n.

• Turn off (arm up) tile ice maker when tile water

supply is to be shut off for several hours.

To Remove the Ice Bin:

• Pull it forward, away from the ice maker. To avoid the

ice maker dunlplng ice wMe tile bin is removed, turn

the ice maker off by raising the ice maker arm.

To Install the Ice Bin:

• Reverse the above procedure. Turn the ice maker oil

by lowering the ice maker arm.

To avoid personal injury or property damage,

observe the foIIowHlg:

• Do not place fingers or hands on tile automatic ice

making mechanBm while the refrigerator is

plugged in. This will help protect you from possible

injury. It will also prevent Interference with moving

parts of tile ejector mechanism and the heating

element that releases tile cubes.

• Under certain rare circumstances, ice cubes may

be discolored, usually appeanng with a green-

bluish hue. The cause of this unusual discoloration

can be a combination of factors such as certain

charactenstlcs of local waters, household

plumbing and the accumulation of copper salts in

an reactive water supply hne which feeds the ice

maker. Continued consumphon of such discolored

Ice cubes may be injurious to health. If such

discoloration is observed, dBcard the ice cubes

and contact your dealer to purchase and install a

water hne filter.

• Water dan]age due to improper water connection

may cause mold/mildew growth.

• Clean up water and Ice spills to avomdpersonal

injury and to prevent moldim_ldew growth.

To Dispense Water:

• Hold container under spout and

press dispenser pad.

Water DispeRser (select models)

The Water Dispenser is located on

the left side wall of the fresh food

section. This design is for cold water

dispensing only.

16

(selectmodels)

17

Water FiRer Removal and

installation

|nitiai installation

The water filter is located in the

upper right-hand corner of the

fresh food compartment.

1. Remove blue bypass cap and

retain for later use.

2. Remove sealing label from

end of filter and insert into

filter head.

3. Rotate gently clockwise until

filter stops. Snap filter cover

closed.

.

Reduce water spurts by

flushing air from system.

Run water continuously for

two minutes through dispenser until water runs

steady. During initial use, allow about a one- to

two-minute delay in water dispersal to allow

internal water tank to fill.

• Additional flushing may be required in some

households where water is of poor quality.

Replacing Water Filter

IMPORTANT: Air trapped in system may cause

water and cartridge to eject. Always dispense

water for at least 2 minutes before removing the

filter for any reason. Use caution when removing.

1. Turn filter counterclockwise until it releases from

filter head.

2. Drain water from filter into sink, and dispose in

normal household trash.

3. Wipe up excess water in filter cover and continue

with Initiallnstallation, steps 2 through 4.

The filter should be changed at least every 12 months.

IMPORTANT: Condition of water and amount used

determines life span of water filter cartridge. If water

use is high, or if water is of poor quality, replacement

may need to take place more often.

To purchase a replacement water filter cartridge,

contact your dealer or call 1-877-232-6771 U.S.A. or

1-880-688-8408 Canada.

The dispenser feature may be used without a water

filter cartridge. If you choose this option, replace filter

with blue bypass cap.

Sltte ol Calilorni t

Deparnnent of Heahh Services

Water Treatment Device

Certificate Number

03- 1583

Dale Issued: Sq3/cmbcr 16. 2003

Dale Rcviscd: April 22. 2004

Trademark/Model Designation Replacement Elements

UKFS001AXX75( 1lKFg(_ IAXX

67003523-750 67003523

Manufacturer= PentaPure hw

The water treatment device(s} listed on this certificate have met the testing requirements

pursuant to Section 1168311 of the Health and Safety (!ode for the following health eelated

contaminants:

Microbiolo_ieaIContamlnams and Turbidity Inor_anic/Radiolo_ical C_ntamlnants

('3 st_

FulbJd 5

Or ftanic Co.tamlnants

Allaznte

I m(_an_

13enzel_

('arboitm_r

dichJorol×,n/en_

_aphenc

R "_t low: 078 _3m

Conditions of Certification:

Do no_ use where waler is microbiologically unsal_ or wilh waler o17 unknown quality, excep_ _l_i_

syslems cer_iJ]e(l l(n ¸ cysl reduclkm may I_ used on disinl_c_ed walers _ha_ may contain filterable

cysts

{selectmodeis)

System Specification and Performance Data Sheet

Refrigerator Water Filter Cartridge Model UKF8001AXX

Specifications

Service Flow Rate (Maximum) .............................................0.78 GPM (2.9 L/min)

Rated Service Life UKF8001AXX-750 (Maximum) ......750 gallons/2838 liters

Maximum Operating Temperature .....................................100° F/38 ° C

Minimum Pressure Requirement ........................................35 psi/241 kPA

Minimum Operating Temperature ......................................33° F/1 ° C

Maximum Operating Pressure .............................................120 psi/827 kPA

PentaPure

1000 Apollo Road

Eagan, Minnesota 55121-2240

651./450.4913

EPA EST #35917-MN-1

Performance Data

Parameter

Chlorine

T&O

Particulate**

100834/B

USEPA

MCL

Standard No, 42: Aesthetic Effects

InfJaent

Challenge Concentration

2,0 mg/L + 10%

IVlin. Required

Redaction

5O%

Iflfhrant

Average

1.88 mg/L

5.700.000 #/ml

Effluent

Average Maximum

C0.05136364mg/L 0.06 mg/L

30,583 #/ml 69,000 #/ml

% Redaction

Average Miniraam

>9726% 96.84%

99.52% 9&94%

at least 10,000 particles/ml 85%

_arameter

Turhidity

Cysts

Asbestos

Lead at pH 6.5

Lead at pH 8.5

Mercury at pH 6.5

Mercury at pH 8.5

Atrazine

Benzene

Carbofuran

3_Dichlorobenzene

Lindane

Toxaphene

USEPA

iVlCL

1 NTU _*

99.5o/,J Reduction

09% Reduction

0.015 mg/L

0.015 nlg/L

0.002 mulL

0.002 mg/L

0.003 mg/L

0.005 mg/L

0.04 mg/L

0.075 mg/L

0.0002 mg/L

0.003 mg/L

Standard No. 53: Health Effects

Inflaent

Challenge Concentration

11 + 1 NTU***

Minimum 50,000/L

10_10_fibers/L; fibers >10 micrometers in length

0.15 mg/L + 10%

.006 mg/L + 10%

0.000 mg/L + 10%

0.015 mg/L + 10%

0.08 mg/L + 10%

.225 mg/L + 10%

0,002 mg/L + 10%

0.015 + 10%

Inllaent

Average

10.7 NTU

166.500 #/L

155 MF/L

0.158 mg/L

0.150 mg/L

0.006 mg/L

0.000 mg/L

0.014 mg/L

0.081 nlg/L

0.208 mg/L

0.002 mg/L

0.015 mg/L

Effluent

Average Maximum

0.31 NTU .049 NTU

<1 #/L <1 #/L

<1 MF/L <1 MF/L

<.001 mg/L <.001 mg/L

0,0003 mg/L 0.0005 mg/L

0.0008 mg/L 0.0015 mg/L

<0.002 mg/L 0.002 mg/L

0.0006 mg/L 0.0011 mg/L

<0,001 mulL <0.001 mg/L

<0.0005 mg/L <0.0005 mg/L

0.000 mg/L <0.0001 mg/L

<0.001 mg/L <0.001 mg/L

% Redaction

Average Miniraam

9709% 95.20%

>99.99% >99.99%

>00.09% >99.99%

>99.35% >90.29%

>99.33% >99.29%

95.70% 90.91%

86.22% 75.03%

76.09% 75.31%

95.71% 02.14%

98.74% 08.46%

99.76% 99.74%

98.72% 96.50%

92.97% 91.67%

Min. Required

Redaction

0.5 NTU

>99.95%

99%

0.10 mg/L

0.002 mg/L

0.003 mg/L

0.005 mg/L

0.04 mg/L

0.075 mg/L

0.0002 mg/L

0.003 mg/L

Tested using a flow rate of 0.78 gpm; pressure of 60 psig; pH of 75 + 0.5; temp. of

68 ° + 5° F (20 ° + 3 ° C)

** Measurement in Particles/ml. Particles used were 0.5 - 1 nlicrons

*** NTU - Nephelometric Turbidity Units

Tested and certified by NSF International against ANSI/NSF Standards 42 & 53

in models UKFS001AXX-750 for the reduction of:

Standard No. 42: Aesthetic Effects Standard No. 53: Health Effects

Taste and Odor Reduction Chemical Reduction Unit

Cldorine Taste & Odor Lead, Atrazine, Lindane, Benzene,

Mechanical Filtration Unit Carbofuran, p-Dichlorobenzene, Mercul_/

Particulate Reduction Class 1 & Toxaphene Reduction

Mechanical Filtration Unit

Cyst, Turbidity and Asbestos Reduction

General Use Conditions

Read this Performance Data Sheet and compare the

capabilities of this unit with your actual water

treatment needs.

DO NOT use this product where water is microbio-

logically unsafe or of unknown quality without

adequate disinfection before or after the system.

System certified for cyst reduction may be used on

disinfected water that may contain filterable cysts.

USE ONLY WiTH COLD WATER SUPPLY. CHECK

FOR COMPLIANCE WiTH THE STATE AND LOCAL

LAWS AND REGULATIONS.

The PuriClean :_II retractable water filtration system uses a

UKF8001AXX replacement cartridge. Timely replacement

of filter cartridge is essential for performance satisfaction

from this filtration system. Please refer to the applicable

section of your Use & Care Guide for general operation,

maintenance requirements and troubleshooting.

Suggested retail price of replacement water filter is $39.99.

This system has been tested according to ANSI/NSF/42 and

53 for reduction of the substance listed above. The

concentration of the indicated substances in water entering

the system was reduced to a concentration less than or

equal to the permissible limit for water leaving the system,

as specified in ANSI/NSF 42 and 53.

18

19

StoregeTips

Fresh Food Storage

• The fresh food compartment of a refrigerator should

be kept between 34°-40 ° F (1°-4 ° C} with an

optimum temperature of 37° F (3° C}. To check the

temperature, place an appliance thermometer in a

glass of water and place in the center of the

refrigerator. Check after 24 hours. If the temperature

is above 40° F (4° C} adjust the controls as explained

on pages 10-12.

* Avoid overcrowding the refrigerator shelves. This

reduces the circulation of air around the food and

results in uneven cooling.

Fruits and Vegetables

Storage in the crisper drawers traps humidity to help

preserve the fruit and vegetable quality for longer

time periods (see page 14}.

• Sort fruits and vegetables before storage and use

bruised or soft items first. Discard those showing

signs of decay.

• Always wrap odorous foods such as onions and

cabbage so the odor does not transfer to other foods.

• While vegetables need a certain amount of humidity

to remain fresh, too much humidity can shorten

storage times (especially leafy vegetables}. Drain

vegetables well before storing.

• Wait to wash fresh produce until right before use.

Meat and Cheese

• Raw meat and poultry should be wrapped securely

so leakage and contamination of other foods or

surfaces does not occur.

Occasionally mold will develop on the surface of

hard cheeses (Swiss, Cheddar, Parmesan}. Cut off at

least an inch around and below the moldy area. Keep

your knife or instrument out of the mold itself. Do not

try to save individual cheese slices, soft cheese,

cottage cheese, cream, sour cream or yogurt when

mold appears.

Dairy Food

• Most dairy foods such as milk, yogurt, sour cream

and cottage cheese have freshness dates on their

cartons for appropriate length of storage. Store these

foods in the original carton and refrigerate

immediately after purchasing and after each use.

Frozen Food Storage

• The freezer compartment of a refrigerator should be

kept at approximately 0° F (-18 ° C}. To check the

temperature, place an appliance thermometer

between the frozen packages and check after 24

hours. If the temperature is above 0° F (-18 ° C},

adjust the control as described on pages 10-12.

A freezer operates more efficiently when it is at least

two-thirds full.

Packaging Foods for Freezing

To minimize dehydration and quality deterioration use

aluminum foil, freezer wrap, freezer bags or airtight

containers. Force as much air out of the packages as

possible and be sure they are tightly sealed. Trapped

air can cause the food to dry out, change color and

develop an off-flavor (freezer burn}.

• Overwrap fresh meats and poultry with suitable

freezer wrap prior to freezing.

• Do not refreeze meat that has completely thawed.

Loading the Freezer

Avoid adding too much warm food to the freezer at

one time. This overloads the freezer, slows the rate of

freezing and can raise the temperature of frozen

foods.

• Leave space between the packages so cold air can

circulate freely, allowing food to freeze as quickly as

possible.

Avoid storing hard-to-freeze foods such as ice cream

and orange juice on the freezer door shelves. These

foods are best stored in the freezer interior where the

temperature varies less with door openings.

Refer to the Food Storage Chart on pages 20 and 21 for

approximate storage times.

La page charge ...

Maytag MFC2061HES - 20 cu. Ft Mode d'emploi

Maytag MFC2061HES - 20 cu. Ft Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents