Jenn-Air JFC2089HTW Le manuel du propriétaire

JENN-AIR

FRENCH DOOR REFRIGERATOR

E

!!ii!ili!ii!iiii i!;;....

JENN-AIR

Form No. 0/12/04 Part No. 12828119

TABLE OF CONTENTS

Important Safety Instructions ........................................1-2

Installation .............................................................................3-9

Temperature Controls ...................................................10-12

Fresh Food Features .....................................................13-14

Freezer Features ...................................................................15

Ice and Water .........................................................................16

Water Filter .......................................................................17-19

Food Storage Tips ..........................................................20-22

Care and Cleaning ........................................................23-26

Operating Sounds ................................................................27

Troubleshooting ..............................................................28-30

Warranty & Service ...............................................................31

Guide de I'utilisateur ...........................................................32

Guia de Uso y Cuidado ......................................................64

Printed in U.S.A.

,_)2004 Maytag Appliances Sales Co.

"i¸¸!_!iii!'i¸i:iiiii_¸i!i_!!!iiii!¸I¸!iiii_!¸I__i!i_i!_!¸il¸iiii!!_iiiil¸¸iiiilill

I MPORTANT SAFETY I NSTRUCTIONS

What You Need to Know About

Safety Instructions

Warning and Important Safety Instructions appearing in

this guide are not meant to cover all possible

conditions and situations that may occur. Common

sense, caution and care must be exercised when

installing, maintaining or operating appliance.

Always contact the manufacturer about problems or

conditions you do not understand.

Recognize Safety Symbols, Words,

Labels

This appliance is equipped with a three-prong

grounding plug for your protection against possible

electrical shock hazards. It must be plugged into a

grounding receptacle. Where a standard two-prong

wall receptacle is encountered, it is the personal

responsibility and obligation of the customer to have it

replaced with a properly grounded three-prong wall

receptacle. Do not under any circumstances, cut or

remove the third (ground) prong from the power cord.

Do not use an adapter plug.

Power supply cord with

three-prong grounding plug

Grounding type

wall receptacle

I MPORTANT SAFETY I NSTRUCTIONS

SAVE THESE INSTRUCTIONS 2

I NSTALLATI 0 N

Your refrigerator was packed carefully for shipment.

Remove and discard shelf packaging and tape. Do not

remove the serial plate.

Location

• Do not install refrigerator near oven, radiator or other

heat source. If not possible, shield refrigerator with

cabinet material.

• Do not install where temperature falls below 55° F

(13° C) or rises above 110° F (43° C). Malfunction may

occur at this temperature.

• Refrigerator is designed for indoor household

application only.

Measuring the Opening

When installing your refrigerator, measure carefully.

Allow '/2"space at top and '/;' space behind the machine

compartment cover (located in the rear) for proper air

circulation.

Subflooring or floor coverings (i.e. carpet, tile, wood

floors, rugs) may make your opening smaller than

anticipated.

Some clearance may be gained by using the leveling

procedure under Leveling.

IMPORTANT: If refrigerator is to be installed into a

recess where the top of the refrigerator is completely

covered, use distance from floor to top of hinge cap to

verify proper clearance.

Transporting Your Refrigerator

• NEVER transport refrigerator on its side. If an

upright position is not possible, lay refrigerator on its

back. Allow refrigerator to sit upright for

approximately 30 minutes before plugging it in to

assure oil returns to the compressor. Plugging the

refrigerator in immediately may cause damage to

internal parts.

• Use an appliance dolly when moving refrigerator.

ALWAYS truck refrigerator from its side or

back-NEVER from its front.

Protect outside finish of refrigerator during transport

by wrapping cabinet in blankets or inserting padding

between the refrigerator and dolly.

Secure refrigerator to dolly firmly with straps or

bungee cords. Thread straps through handles when

possible. Do not overtighten. Overtightening

restraints may dent or damage outside finish.

Glass Panel Doors (select models)

-%

I NSTALLATI 0 N

Leveling

To enhance the appearance and maintain performance,

the refrigerator should be level.

3. Using hex head driver, turn the front adjustment

screws (A) on each side to raise or lower the front

of the refrigerator.

Note

• Complete any required door reversal, panel

installation and/or a water supply connection,

before leveling.

Materials Needed:

• 3/8"hex head driver

• Carpenter's level

1. Remove toe grille.

• Grasp firmly and pull outward

to unclip.

2. Remove bottom hinge cover(s).

• Place the eraser end of a pencil or similar blunt

tool in the cover notch.

Notch

Location

• Use slight pressure to pry the

cover loose.

• Continue to maintain

downward pressure to the

notched side of the cover while

swinging it off.

I Note

• Some models only have adjustment screws "A:'

,

.

Using the hex head driver, turn each of these

adjustment screws (B) to raise or lower the rear of

the refrigerator.

Using the carpenter's level, make sure front of

refrigerator is Y4"(6 ram) or '/8bubble higher than

back of refrigerator and that the refrigerator is level

from side to side.

6. Turn stabilizing legs ((3) clockwise until firmly

against floor.

7. Turn adjustment screws (A) counterclockwise to

allow the full weight of the refrigerator to rest on

the stabilizing legs.

8. Replace bracket cover(s).

• Position cover into the outer edge of the hinge.

• Swing the cover toward the cabinet and snap it

into place.

9. Replace the toe grille.

Note

• For proper reinstallation, ensure the "top" marking

on the interior of the toe grille is oriented correctly.

• Align the toe grille mounting clips with the lower

cabinet slots.

• Push the toe grille firmly until it snaps into place.

I NSTALLATI ON

Door and Drawer Removal

Some installations require door/drawer removal to

transport the refrigerator to its final location.

.

Remove center hinge pin with a 5/,6"

hex head driver and retain hinge pin

for later use.

Remove Phillips screws to remove

right and left hinges and retain all

screws for later use.

Remove both stabilizing brackets with 3/;, hex head

driver and retain screws for later use.

Pullout Freezer Drawer

(select models)

1. Unplug power cord from power source.

2. Remove toe grille and bottom hinge

cover(s) (see page 4).

3. Remove top hinge cover from

refrigerator door by removing Phillips

screw and retain screw and cover for

later use.

4. Unscrew _/,5"hex head screws from t_

top hinge to remove hinge and retain

all screws for later use.

5. Lift right side refrigerator door from

center hinge pin. Remove door

closure from center hinge pin on

. right

the right side and retain for later s_de

use. ---.'_-_I door

osure

6. Disconnect wire harness on top

of left side refrigerator door top

hinge. ..

Release two-pin connector by

pressing junction point with a

flat blade screwdriver or

fingernail.

Green ground wire remains

attached to the hinge.

7. Unscrew _/,5"hex head screws from

top hinge to remove hinge and retain ,

for later use. ._

Lift left side refrigerator door, along

with top hinge, from center hinge pin. "

To Remove:

1. Pull drawer open to full extension.

2. Tilt the lower basket forward and lift to remove.

3. On each white drawer

bracket is a basket cradle

with two snap attachments.

To release each cradle,

unlatch the snaps by

pushing them inward, away

from the side bracket. Lift

the cradles off of the rails.

4. Remove Phillips screw

from each of the drawer

slides (select models).

I NSTALLATI 0 N

5. Lift top of drawer front

to unhook the drawer

from the slides. Lift

door front out to

remove.

To Install:

1. Pull both rails out to

full extension.

2. While supporting door front, hook supports into

slots located on inside of each slide.

Note

• All four drawer bracket supports must be in the

proper slots for the drawer to function properly.

3. Lower door front into final position.

4. Replace and tighten Phillips screws that were

removed from the drawer slides (select models).

5. Place the basket cradles back onto the drawer

slides. Align basket cradle snaps with the slots on

the drawer brackets and press each cradle

towards the bracket until it clicks.

Basket cradle

snap attachments

6. Tilt the lower basket front down and set it down

into the basket cradles.

Door Reinstallation

1. Install hinge assemblies:

• Install center hinge with Phillips screws.

2. Place hinge side of refrigerator door on center

hinge pin.

• Install top hinge with 5/,6"hex head

screws.

3. While holding refrigerator door

upright, tighten down top hinge

with ?,5"hex head driver.

/4. Reconnect two-pin connector.

5. Replace top hinge covers.

Handles ([style varies by model)

This handle style is installed at the factory. Style may

vary by model.

Materials Needed:

• 3/32"allen wrench

To Remove:

• Remove set screw from

handle mounting post

using the 3/_;,allen

wrench.

• Repeat the procedure on

all posts to remove the

handle.

To replace:

• Align handle with the mounting posts.

• Fully tighten all set screws to secure handle

in place.

I NSTALLATI 0 N

Installing Front-Mounted Handles for

Stainless Steel Door

1. Loosen lower door clip on door with a

phillips screwdriver.

2. Locate predrilled hole at base of

handle, and fit hollow end of

handle over lower door clip.

3. Fit other end of handle over upper

door clip and slide up as far as

possible.

NOTE: If top of handle does not

fit over top clip, loosen lower clip

further until fit can be

accomplished.

/4. Insert phillips screwdriver into

predrilled hole at base of handle

to tighten screw. Insert plastic

button plug into hole.

5. Repeat above steps to install other handle.

Removing Front-Mounted Handles for

Stainless Steel Door

1. Remove plastic button plug at base

of handle with a very small flat-blade

sc rewd river.

• Insert phillips screwdriver into

predrilled hole to remove screw.

2. Slide handle down and remove from

door clip.

3. Repeat above steps to remove

other handle.

Installing Front-Mounted Handles for

Stainless Steel Freezer Door

1. Loosen lower door clip on door

with a phillips screwdriver.

2. Locate predrilled hole at

base of handle, and fit hollow

end of handle over left door

clip.

.

Fit other end of handle over

left door clip and slide left as

far as possible.

NOTE: If end of handle does

not fit over left clip, loosen

right clip further until fit can

be accomplished.

Insert phillips screwdriver

into predrilled hole at end of

handle to tighten screw.

Insert plastic button plug into

hole.

Removing Front-Mounted Handles for

Stainless Steel Freezer Door

1. Remove right side plastic button

plug at end of handle with a

very small flat-blade screwdriver. ...................

• Insert phillips screwdriver into

predrilled hole to remove

screw.

2. Slide handle right and remove

from door clip.

I NSTALLATI 0 N

Opening and Closing Your

Fresh Food Doors

Your new refrigerator is uniquely designed with two

fresh food doors. Either door can be opened or closed

independently of one another.

There is a vertically-hinged section on the left fresh

food door. When the left door is closed, the hinged

section automatically forms a seal between the two

doors when both doors are closed.

When the left door is opened, the hinged seal

automatically folds inward so that it is out of the way.

I NSTALLATI 0 N

Connecting the Water Supply

Materials Needed:

• '/a"outer diameter flexible copper tubing

• Shut-off valve (requires a '//' hole to be drilled into

water supply line before valve attachment)

• Adjustable wrench

• X" hex nut driver

Notes

• Use copper tubing only for installation. Plastic is

less durable and can cause damage.

• Add 8' to tubing length needed to reach water

supply for creation of service loop.

2' diameter

1. Create service loop with copper minimum

tubing (minimum 2' diameter), f_-_._

Avoid kinks in the copper tubing _" '_, *

when bending it into a service

loop. Do not use plastic tubing.

2. Remove plastic cap from water valve inlet AN

port. _:_(:_

,

.

Place brass nut (A) and sleeve (B) A, "-,B

on copper tube end as illustrated. _ ,,,

Reminder: Do not use an old _: _:_i_"

sleeve. The nut and sleeve are

provided in the use and care packet.

Place end of copper tubing into water

valve inlet port. Shape tubing slightly. Do

not kink - so that tubing feeds straight

into inlet port.

5. Slide brass nut over sleeve and screw nut

into inlet port. Tighten nut with wrench.

IMPORTANT: Do not overtighten. Cross

threading may occur.

,

Pull on tubing to confirm connection is

secure. Connect tubing to frame with

water tubing clamp (C) and turn on

water supply. Check for leaks and

correct if necessary. Continue to

observe the water supply connection

i i

for two to three hours prior to moving

the refrigerator to its permanent

location.

7. Monitor water connection for 24 hours. Correct

leaks, if necessary.

TEMPERATURE CONTROLS

Touch Temperature Controls

The controls are located at the top front of the

refrigerator compartment.

Control

Initial Control Settings

After plugging the refrigerator in, set the controls.

• Pressing the Vor A.pads adjusts the controls to

the desired setting.

• The temperature control range for both

compartments is 1 through 7 (coldest).

• Initially set the refrigerator control on 4.

• Initially set the freezer control on 4.

• Let the refrigerator run at least 8 to 12 hours before

adding food.

Warm Cabinet Surfaces

At times, the front of the refrigerator cabinet may be

warm to the touch. This is a normal occurrence that

helps prevent moisture from condensing on the

cabinet. This condition will be more noticeable when

you first start the refrigerator, during hot weather and

after excessive or lengthy door openings.

Adjusting the Controls

24 hours after adding food, you may decide that one

or both compartments should be colder or warmer. If

so, adjust the control(s) as indicated in the

Temperature Control Guide table below. See page 20

for instructions on checking compartment

temperature.

• Except when starting the refrigerator, do not change

either control more than one number at a time.

• Allow 2/4 hours for temperatures to stabilize.

• Changing either control will have some effect on the

temperature of the other compartment.

Temperature Control Guide

Refrigerator too warm Set the refrigerator control

to next higher number by

pressing the Apad.

Refrigerator too cold

Freezer too warm

Freezer too cold

Turn refrigerator OFF

Set the refrigerator control

to next lower number by

pressing the Vpad.

Set the freezer control to

next higher number by

pressing the Apad.

Set the freezer control to

next lower number by

pressing the _ pad.

Press the refrigerator or

freezerv pad until a dash

(-) appears in the display.

10

TEMPERATURE CONTROLS

Trisensor Climate Control

(select models)

The control is located at the top front of the fresh food

compartment.

Control

Speed Ice

When activated, Speed Ice reduces the freezer

temperature to the optimum setting for 24

hours in order to produce more ice. Note: When the

Speed Ice feature is in operation, the Aand Vpads

for the freezer control will not operate.

11

Initial Temperature Setting

Temperatures are preset at the factory at 38° F (3° C)

in the fresh food compartment and 0° F (-18 ° C) in the

freezer compartment.

Adjusting the Control

24 hours after adding food, you may decide that one

or both compartments should be colder or warmer. If

so, adjust the control as indicated in the Temperature

Control Guide below.

• The first touch of the V or A pads shows the

current temperature setting.

The display will show the new setting for

approximately three seconds, and then return to the

actual temperature currently within that

compartment.

• Do not change either control more than one degree

at a time. Allow temperature to stabilize for 24 hours

before making a new temperature adjustment.

Temperature Control Guide

Refrigerator too cold

Refrigerator too warm

Freezer too cold

Freezer too warm

Turn refrigerator OFF

Set the refrigerator control

to next higher number by

pressing the _ pad.

Set the refrigerator control

to next lower number by

pressing the _ pad.

Set the freezer control to

next higher number by

pressing the _IL pad.

Set the freezer control to

next lower number by

pressing the _ pad.

Press the freezer pad

until OFF appears in the

display. Press either the

freezer or refrigerator V

pad to turn back on.

Reset Filter (select models)

When a water filter has been installed in the

refrigerator, the yellow Order light will

illuminate when 90 percent of the volume of water for

which the filter is rated has passed through the filter

OR 11 months have elapsed since the filter has been

installed.

The red Replace light will illuminate when the rated

volume of water has passed through the filter OR 12

months have elapsed since the filter was installed. A

new filter should be installed immediately when the

Replace light is illuminated.

After replacing the filter, press and hold the Reset

Filter pad for three seconds. The Order and Replace

lights will go off.

Vacation Mode

The Vacation Mode feature causes the freezer

to defrost less frequently, conserving energy. The

Vacation Mode indicator light will illuminate when the

feature is activated. To deactivate, press the Vacation

Mode pad again OR open either door. The indicator

light will go out.

Notes

• Door openings will not deactivate Vacation Mode

for approximately one hour after activation.

• If vacationing for more than a few days, see the

Preparing for Vacation section, page 26.

Temp Alarm

The Temp Alarm system will alert you if the

freezer or fresh food temperatures exceed

normal operating temperatures due to a power outage

or other event. When activated, the Temp Alarm light

will illuminate.

If the freezer or fresh food temperatures have

exceeded these limits, the display will alternately show

the current compartment temperatures and the highest

compartment temperatures reached when the power

was out. An audible alarm will sound repeatedly.

TEMPERATURE CONTROLS

Press the Temp Alarm pad once to stop the audible

alarm. The Temp Alarm light will continue to flash and

the temperatures will alternate until the temperatures

have stabilized.

To turn off Temp Alarm, press and hold the Temp Alarm

pad for three seconds. The indicator light will go off.

Door Alarm

The Door Alarm will alert you when one of the

doors has been left open for five continuous minutes.

When this happens, an audible alarm will sound every

few seconds until the door is closed OR press the Door

Alarm pad to deactivate the feature.

Max Cool

When activated, Max Cool causes the fresh food

and freezer temperatures to drop to the minimum

settings on the control. This cools down the

refrigerator and freezer after extended door openings

or when loading the refrigerator or freezer with warm

food.

Note: When the Max Cool feature is in operation,

the A and rv pads for the refrigerator and freezer

controls will not operate.

To activate, press the Max Cool pad. Max Cool will

deactivate automatically after 12 hours, OR press the

Max Cool pad to deactivate the feature.

User Preferences

Access the User Preferences menu to:

• Activate or turn off Super Cool (select models)

• Change the temperature display from °F to °C

• Enable or disable audible alarms.

• Adjust the light level at which the Dispenser Auto

Light will illuminate (when this feature is activated on

the ice and water dispenser) (select models)

• Activate the Sabbath Mode

To access the User Preferences menu, press and hold

the Door Alarm pad for three seconds. When in the

User Preferences mode, a short title for the feature will

appear in the Freezer temperature display and the

feature status will appear in the Fresh Food display.

1. Use the Freezer up and down control to scroll

through the features.

2. When the desired feature is displayed, use the Fresh

Food up and down control to change the status.

3. When changes are complete, press the Door Alarm

pad for three seconds OR close the Fresh Food

door.

Super Cool (CO) (select models)

When Super Cool is ON, an air-mixing fan in the fresh

food compartment is activated to improve air flow and

temperature control. To save energy, this feature may

be deactivated by choosing OFE

Temperature Display (F_C)

Change the display to show temperatures in degrees

Fahrenheit or degrees Celsius.

Alarm (AL)

When the Alarm mode is OFE all audible alarms will

be disabled until the feature is turned on.

Auto Light Level Selection (LL) (select models)

This setting adjusts the light level at which the

dispenser light will illuminate when the sensor detects

that the light levels in the room are low. Setting 1 is

the darkest light level setting, setting 9 is the lightest

light level setting. Note: The Auto Light (select

models) must be activated on the ice and water

dispenser control to take advantage of this option.

Sabbath Mode (SAB)

When the Sabbath Mode is ON, all control lights and

the night light will be disabled until the feature is

turned OrE This feature does not disable the interior

lights. Press any pad to restore the control lights.

Warm Cabinet Surfaces

At times, the front of the refrigerator cabinet may be

warm to the touch. This is a normal occurrence that

helps prevent moisture from condensing on the

cabinet. This condition will be more noticeable when

the refrigerator is first started, during hot weather and

after excessive or lengthy door openings.

12

FRESH FOOD FEATURES

Shelves

• Place hand under the frame to push up the glass. Lift

glass out.

• Lift frame from refrigerator liner rails.

To Install:

• Replace frame in refrigerator liner rails.

• Carefully replace glass into frame.

Your refrigerator has Spill-proof Glass Shelves. The

Spill-proof shelves have a spill retainer edge which

allows for easier clean up and are equipped with a

slide out feature. To slide out, grasp the front of the

shelf and pull forward. Push in the shelf to return to

the original position.

To Remove a Shelf:

• Slightly tilt up the front and lift up

the rear of the shelf, then pull the

shelf straight out.

To Lock the Shelf Into Another

Position:

• Tilt up the front edge of the shelf.

• Insert the hook into the desired frame openings and

let the shelf settle into place.

• Be sure the shelf is securely locked at the rear.

Rear Shelf Extensions

Rear Shelf Extensions help prevent articles from

falling off the back of the shelf.

To remove and install shelf extension:

• To remove, pull extension straight up from the rear of

shelf.

• To install, insert posts of the

shelf extension into holes in the

shelf frame.

The Crisper "lop serves as the lower fresh food shelf.

To Remove the Crisper Top:

• Remove crisper drawers.

Door Storage

Dairy Center

The Dairy Center provides

convenient door storage for

spreadable items such as butter

and margarine. This compartment can be moved to

different locations to accommodate storage needs. To

use the dairy center, raise the cover.

To Remove:

• Raise the cover, pull upward and tilt out.

To Install:

• Slide the Dairy Center in and down until firmly seated

in the door liner.

Door Buckets

Door Buckets can be moved to meet storage needs.

To Remove:

• Slide bucket up and pull straight out.

To Install:

• Slide bucket in and down until

firmly seated in the door liner.

Crisper Drawers

The Crisper Drawers provide a higher humidity

environment for fresh fruit and vegetable storage.

Controls

The Crisper Controls regulate the amount of humidity

in the crisper drawer. Slide the control toward the Fruit

setting for produce with outer skins. Slide the control

toward the Vegetables setting for leafy produce.

I

13

FRESH FOOD FEATURES

To Remove:

• Pull drawer out to full extension. Tilt up front of

drawer and pull straight out.

To Install:

• Insert drawer into frame rails and push back into

place.

Note

• For best results, keep the crisper drawers tightly

closed.

Gourmet BayTM

The Gourmet Bay TM drawer is a full-width drawer with

adjustable temperature control. This drawer can be

used for large party trays, deli items, beverages or

miscellaneous items. There is a divider to

organize the drawer into sections if desired. A

There is a temperature control which adjusts A

the amount of cold air allowed into the A

A

Gourmet Bay TM. The control is located on the

A

right of the drawer, under the lid.

Set the control to cold _ to provide a normal

refrigerator temperature. Set the drawer on the

coldest _ setting when a temperature colder than the

main refrigerator compartment is desired. Use the

coldest setting when storing meats.

Notes

• Cold air directed to the Gourmet BayTM drawer can

decrease refrigerator temperature. Refrigerator

control may need to be adjusted.

• Do not place leafy vegetables in the Gourmet

BayTM drawer. Colder temperatures could damage

leafy produce.

To Remove:

• Lift lid. Pull drawer out to full extension. Tilt the

drawer front up and pull straight out.

To Install:

• Push metal glide rails to the back of the refrigerator.

Place drawer onto rails and slide drawer back until it

falls into place.

To Remove Divider:

• Pull drawer completely out and raise the front of the

divider to unhook it from the rear wall of the pantry

and lift it out.

To Install Divider:

• Hook back of divider over rear wall of pantry and

lower into place.

Accessories

Wine Trivet/Can Rack (select models)

The Wine Trivet/Can Rack

accessory fits in the Gourmet BayTM

or on a shelf.

Bottles or cans can be laid

crosswise, or a single bottle may be

laid in the center depression.

Gourmet Bay TM Tray

The Gourmet Bay TM Tray allows for a

removable tray within the full-width

storage drawer.

Adjustable Storage Rack ,,__

The Adjustable Storage Rack provides

a place for horizontally storing wine. The

rack can also hold an egg carton.

Position the rack to rest on the left hand side of a

refrigerator shelf.

Egg Cradle

The Egg Cradle (style may vary)

holds a "dozen-plus" eggs. It can be

removed to carry to work area or to be

washed.

14

FREEZER FEATURES

Upper Wire Basket

To Remove:

• Pull upper basket out to full extension and lift out to

remove.

To Install:

• Slide upper basket into freezer. Make sure that rear

of basket hooks behind rail catch.

Note

• Lower Freezer Drawer: See page 5 for lower

basket and complete pullout drawer instructions.

Accessories

Ice Bin

The Ice Bin provides storage

for ice.

Lower Basket Tray

The Basket Tray is a removable

plastic item that rests on the

bottom of the lower pullout

basket to catch spills and small

food items before they can fall

through to the freezer

corn partment.

The tray can be removed for easy

cleaning by lifting the tray from the basket.

Lower Basket Divider

The Lower Basket Divider allows the option to

organize the basket area into sections.

To remove and replace divider:

• To remove, pull divider straight up.

• To install, hook top corners of divider over top

horizontal basket rungs.

15

12828119 Jenn-Air Trio Eng 1/14/05 8:53 AM Page 17

ICE AND WATER

Automatic Ice Maker

Connect the ice maker to the water supply as

instructed on page 9. Proper water flow and a level

refrigerator are essential for optimal ice maker

performance.

Operating Instructions

• Confirm ice bin is in place and ice

maker arm is down.

After freezer section reaches

between 0° to 2° F (-18° to -17° C),

ice maker fills with water and

begins operating. You will have a

complete harvest of ice approximately every three

hours.

• Allow approximately 24 hours after installation to

receive first harvest of ice.

Discard ice created within first 12 hours of operation

to assure system is flushed of impurities.

Stop ice production by raising ice maker arm until

click is heard.

Ice maker will remain in the off position until arm is

pushed down.

The first one or two batches will probably contain

undersized and irregular cubes because of air in the

supply line.

When the ice cubes are ejected it is normal for

several cubes to be joined together at the ends. They

can easily be broken apart. The ice maker will

continue to make ice until the supply of ice cubes

raises the ice maker arm, shutting the ice maker off.

Certain sounds may accompany the various cycles of

the ice maker. The motor may have a slight hum, the

cubes will rattle as they fall into an empty storage

pan and the water valve may click or "buzz"

occasionally.

If the ice is not used frequently, the ice cubes will

become cloudy, shrink, stick together and taste stale.

Empty the ice storage bin periodically and wash it in

lukewarm water. Be sure to dry the bin thoroughly

before replacing it.

Beverages and foods should not be placed in the ice

storage bin for quick chilling. These items can block

the ice maker arm, causing the ice maker to

malfunction.

• Turn off (arm up) the ice maker when the water

supply is to be shut off for several hours.

To Remove the Ice Bin:

• Pull it forward, away from the ice maker. To avoid the

ice maker dumping ice while the bin is removed, turn

the ice maker off by raising the icemaker arm.

To Install the Ice Bin:

• Reverse the above procedure. Turn the ice maker on

by lowering the ice maker arm.

Water Dispenser

The Water Dispenser is located on

the left side wall of the fresh food

section. This design is for cold water

dispensing only.

To Dispense Water:

• Hold container under spout and

press dispenser pad.

16

12828119 Jenn-Air Trio Eng 1/14/05 8:53 AM Page 18

WATER FILTER

Removal and Installation

Initial Installation

The water filter is located in the

upper right hand corner of the fresh

food compartment.

1. Remove blue bypass cap and

retain for later use.

2. Remove sealing label from end of

filter and insert into filter head.

3. Rotate gently clockwise until filter stops. Snap filter

cover closed.

Reduce water spurts by flushing air from system.

Run water continuously for two minutes through

dispenser until water runs steady. During initial

use, allow about a one- to two-minute delay in

water dispersal to allow internal water tank to fill.

• Additional flushing may be required in some

households where water is of poor quality.

Replacing Water Filter

IMPORTANT: Air trapped in system may cause

water and cartridge to eject. Always dispense

water for two minutes before removing the filter

for any reason. Use caution when removing.

1. Turn filter counterclockwise until it releases from

filter head.

2. Drain water from filter into sink, and dispose of

filter in normal household trash.

3. Wipe up excess water in filter cover and continue

with Initial Installation, steps 2 through 4.

The filter should be changed at least every 12 months.

Important: Condition of water and amount used

determines life span of water filter cartridge. If water

use is high, or if water is of poor quality, replacement

may need to take place more often.

To purchase a replacement water filter cartridge,

call 1-800-JENNAIR (1-800-536-6247) U.S.A. and

Canada.

The dispenser feature may be used without a water

filter cartridge. If you choose this option, replace filter

with blue bypass cap.

17

12828119 Jenn-Air Trio Eng 1/14/05 8:53 AM Page 19

WATER FILTER

PuriQe ,f." System Specification and Performance Data Sheet

Refrigerator Water Filter Cartridge Model UKF8001AXX

Specifications

Service Flow Rate (Maximum) .............................................0.78 GPM (2.9 L/rain)

Rated Service Life UKF8001AXX-750 (Maximum) ......750 gallons/2838 liters

Maximum Operating Temperature .....................................100° F/38 ° C

Minimum Pressure Requirement ........................................35 psi/241 kPA

Minimum Operating Temperature ......................................33° F/1 ° C

Maximum Operating Pressure .............................................120 psi/ 827 kPA

]000ApolloRoad

[agan, Minnesota 55121-2240

651.450.4913

EPA EST #35917-MN-1

Performance Data

Parameter

Chlorine

T&O

Particulate _*

100834/B

USEPA

MCL

Standard No. 42: Aesthetic Effects

Influent

Challenge Concentration

2.0 mg/L ± 10%

Influent

Average

1.88 mg/L

Effluent

Average Maximum

<0.05136364 mg/L 0.06 RIg/L

Min. Required

Reduction

50%

%Reduction

Average Minimum

>97260/0 96.84%

99.52o/0 98.94%

at least 10,000 particles/ml 5,700,000 #/ml 30,583 #/ml 69,000 #/ml 85%

Parameter

Turbidi b,

Cysts

Asbestos

Lead at pH 65

Lead at pH 8.5

Mercury at pH 6.5

Mercury at pH 8.5

Atrazine

Benzene

Carbofuran

p-Dichlorobenzene

Lindane

Toxaphene

USEPA

MCL

1 NTU**

99.5% Reduction

99% Reduction

0.015 mg/L

0.002mg/L

0.003mg/L

0.005mg/L

0.04 mg/L

0.075 mg/L

0.0002 mg/L

0.003mg/L

Standard No. 53: Health Effects

Influent

Challenge Concentration

11 ± 1 NTU***

Minimum 50.000/L

10710Bfi bers/[;libers >10 n/icrometers in length

0.15 mg/L + 10%

.006 mg/L ± 10%

0.009 mg/L + 10%

0.015 mg/L ± 10%

0.08 mg/L ± 10%

.225 nl_)/L ± 10o/o

0.002 mg/L + 10%

0.015 ± 10o/o

Influent

Average

10.7 NTU

166.500 #/L

155MF/L

0.153 mg/L

0.150 mg/L

0.006 mg/L

0.009 mg/L

0.014 mg/L

0.081 mg/L

0.208 mg/L

0.002 mg/L

0.015 mg/L

Effluent

Average Maximum

0.31 NTU .049 NTU

<1 #/L <1 #/L

<1 MF/L <1 MF/L

<.001 mg/L <.001 mg/L

0.0003 mg/L 0.0005 mg/L

0.0008 mg/L 0.0015 mg/L

<0.002 mg/L 0.002 mg/L

0.0006 mg/L 0.0011 mg/L

<0.001 mg/L <0.001 mg/L

<0.0005 mg/L <0.0005 mg/L

0.000 mg/L <0.0001 mg/L

<0.001 mg/L <0.001 mg/L

% Reduction

Average Minimum

9709% 95.20%

>99.99% >99.99%

>g9.35% >gg.29%

>99.33% >99.29%

g5.70% g0.91%

86.22% 75.93%

76.g9% 75.31%

95.71o/o 92.14%

98.74% 98.46o/o

99.76% 99.74%

98.72% 96,50o/o

92.970/o 91.67%

Min. Required

Reduction

0.5 NTU

>99.95%

99%

0.10 mg/L

0.002 mg/L

0.003 mg/L

0.005 mg/L

0.04 mg/L

0.075 mg/L

0.0002 mg/L

0.003 mg/L

* Tested using a flow rate of 0.78 gpm; pressure of 60 psig; pH of 75 + 0.5; temp. of

68 ° + 5 ° F (20 ° + 3 ° C)

** Measurement in Particles/mL Particles used were 0.5 - 1 microns

*** NTU - Nephelometric Turbidi b, Units

Standard No. 42: Aesthetic Effects

Taste and Odor Reduction

Chlorine Taste & Odor

Mechanical Filtration Unit

Particulate Reduction Class 1

Tested and certified by NSF IntemaUonal against ANSI/NSF Standards 42 & 53

in models UKFS00tAXX-750 for the reduction of:

Standard No. 53: Health Effects

Chenlical Reduction Unit

Lead. Atrazine. Lindane. Benzene.

Carbofuran. p-Dichlorobenzene. MercLuy

& Toxaphene Reduction

Mechanical Filtration Unit

Cyst Turbidity and Asbestos Reduction

General Use Conditions

Read this Performance Data Sheet and compare the

capabilities of this unit with your actual water treatment

needs.

DO NOT use this product where water is microbiologic-

ally unsafe or of unknown quality without adequate

disinfection before or after the system. System certified

for cyst reduction may be used on disinfected water

that may contain filterable cysts.

USE ONLY WITH COLD WATER SUPPLY. CHECK FOR

COMPLIANCE WITH THE STATEAND LOCAL LAWS

AND REGULATIONS.

The PuriClean_II retractable water filtration system uses a

UKF8001AXX replacement cartridge. Timely replacement of

filter cartridge is essential for performance satisfaction from

this filtration system. Please refer to the applicable section of

your Use & Care Guide for general operation, maintenance

requirements and troubleshooting. Suggested retail price of

replacement water filter is $39.99.

This system has been tested according to ANSI/NSF 42 and

53 for reduction of the substance listed above. The

concentration of the indicated substancesin water entering

the system was reduced to a concentration less than or equal

to the permissible limit for water leaving the system, as

specified in ANSI/NSF 42 and 53.

18

12828119 Jenn-Air Trio Eng 1/14/05 8:53 AM Page 20

+

WATER FILTER

State of California

Department of Health Services

Water Treatment Device

Certificate Number

03- 1583

Date Issued: September 16, 2003

Date Revised: April 22, 2004

Trademark;Model Designation

UKFS001AXX750

469006-750

67003523-750

Replacement Elements

UKFS001AXX

46 9006

67003523

Manufacturer: PentaPure Inc,

The water treatment devicet s J listed on this certificate have met the testing requirements pursuant to Section 116830 of the

Health and Safety Code for the following health related contaminants:

Microbiological Contaminants and Turbidity

Cysts

Turbidity

Inorganic/Radiological Contaminants

Asbestos

Lead

Mercury

Organie Contaminants

Atrazine

Lindane

Benzene

Carboturan

p-dichlorobenzene

Toxaphene

Rated Service Capacity: 750 gal. Rated Service Flow: 0.78 gpm

Conditions of Certification:

Do not use where water is microbiologically unsafe or with water of unknown quality, except that systelns certified for cyst

reduction may be used on disinfected waters that may contain filterable cysts.

19

+

La page est en cours de chargement...

Jenn-Air JFC2089HTW Le manuel du propriétaire

Ce manuel convient également à

Jenn-Air JFC2089HTW Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents