NAPOLEON NEFV38H Le manuel du propriétaire

Marque: NAPOLEON

Modèle: NEFV38H

Catégorie: Cheminées

Taper: Le manuel du propriétaire

W415-1352 / B / 08.08.18

INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.

CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.

NEVER LEAVE CHILDREN OR OTHER AT RISK INDIVIDUALS ALONE WITH THE APPLIANCE.

INSTALLATION AND

OPERATING INSTRUCTIONS

1.16E

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada /

103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone (705)721-1212 • Fax (705)722-6031 • www.napoleonﬁ replaces.com •[email protected]

SAFETY INFORMATION

WARNING

If the information in these instructions are

not followed exactly, a ﬁ re or explosion

may result causing property damage,

personal injury or loss of life.

- Do not store or use gasoline or other ﬂ ammable

vapors and liquids in the vicinity of this or any

other appliance.

$10.00

CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARDS: CSA C22.2 No-46 / UL 2021

NEFV38H

ELECTRIC FIREPLACE

W415-1352 / B / 08.08.18

NOTE: Changes, other than editorial, are denoted by a vertical line in the margin.

TABLE OF CONTENTS

1.0 INTRODUCTION 3

1.1 DIMENSIONS 4

1.2 LISTING APPROVALS 4

1.3 GENERAL INSTRUCTIONS 5

1.4 UNPACKING AND TESTING APPLIANCE 5

1.5 PARTS SUPPLIED 6

2.0 LOCATING APPLIANCE 7

2.1 GROUNDING APPLIANCE 7

3.0 INSTALLATION 8

3.1 MINIMUM CLEARANCE TO COMBUSTIBLES 8

3.2 INSTALLING THE APPLIANCE - WALL MOUNT 9

3.4 RECESSING INSTALLATION 10

3.4.1 BUILT-IN FRAMING 10

3.4.2 MOUNTING BRACKET INSTALLATION 11

3.5 HARD WIRING INSTALLATION 12

4.0 FINISHING 13

4.2 GLASS FRONT REMOVAL 13

4.1 CRYSTAL EMBER INSTALLATION 13

5.0 OPERATING INSTRUCTIONS 14

5.1 MAIN POWER SWITCH & OPERATING CONTROLS 14

6.0 MAINTENANCE 15

6.1 PCB (CONTROL BOARD) 15

6.2 REMOTE BATTERY INSTALLATION 15

7.0 WIRING DIAGRAM 16

8.0 REPLACEMENT PARTS 17

9.0 TROUBLESHOOTING 19

10.0 WARRANTY 20

11.0 SERVICE WARRANTY 21

12.0 NOTES 22

W415-1352 / B / 08.08.18

1.0 INTRODUCTION

WARNING

3.7C

• THIS APPLIANCE IS HOT WHEN OPERATED AND CAN CAUSE SEVERE BURNS IF

CONTACTED.

• Do not operate appliance before reading and understanding operating instructions. Failure to operate

appliance according to operating instructions could cause ﬁ re or injury.

• Risk of burns. Power to the appliance should be turned off and the appliance allowed to cool before

servicing. To disconnect power to the appliance, turn controls to off, then remove plug from outlet.

• Do not install damaged, incomplete or substitute components.

• Do not burn wood or other materials in this appliance.

• Young children should be carefully supervised when they are in the same room as the appliance.

Toddlers, young children and others may be susceptible to accidental contact burns. A physical barrier

is recommended if there are at risk individuals in the house. To restrict access to an appliance or stove,

install an adjustable safety gate to keep toddlers, young children and other at risk individuals out of the

room and away from hot surfaces.

• Clothing or other ﬂ ammable material should not be placed on or near the appliance.

• Due to high temperatures, the appliance should be located out of trafﬁ c and away from furniture and

draperies.

• Ensure you have incorporated adequate safety measure to protect infants/toddlers from touching hot

surfaces.

• Even after the appliance is out, the glass and/or screen will remain hot for an extended period of time.

• Check with your local hearth specialty dealer for safety screens and hearth guards to protect children

from hot surfaces. These screens and guards must be fastened to the ﬂ oor.

• Any safety screen or guard removed for servicing must be replaced prior to operating the appliance.

• It is imperative that the control compartments, circulating blower and its passageway in the appliance

and are kept clean. The appliance should be inspected before use and at least annually by a qualiﬁ ed

service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding

material, etc. The appliance area must be kept clear and free from combustible materials, gasoline and

other ﬂ ammable vapors and liquids.

• Under no circumstances should this appliance be modiﬁ ed.

• Do not use this appliance if any part has been under water. Immediately call a qualiﬁ ed service technician

to inspect the appliance and to replace any part of the control system which has been under water.

• Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the

glass should be done by a licensed or qualiﬁ ed service person.

• Do not strike or slam shut the appliance glass door.

• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As

with all plastic bags, these are not toys and should be kept away from children and infants.

• Servicing should be done only while the appliance is disconnected from the power supply circuit.

• Always unplug appliance when not in use.

• Do not operate this appliance with a damaged cord or plug after the appliance malfunctions, has been

dropped or damaged in any manner. Return appliance to authorized service facility for examination,

electrical or mechanical adjustment, or repair.

• Do not use outdoors.

• Never locate appliance where it may fall into a bathtub or other water container.

• Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or the like. Arrange cord

away from trafﬁ c area and where it will not be tripped over.

• Connect to properly grounded outlets only.

• Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an

electric shock or ﬁ re, or damage the appliance.

• To prevent a possible ﬁ re, do not block air intakes or exhaust in any manner. Do not use on soft

surfaces, like a carpet, where openings may become blocked.

• Always plug appliances directly into a wall outlet/receptacle. Never use an extension cord or

relocatable power tap (outlet/power strip).

• Ensure clearances to combustibles are maintained when building a mantel or shelves above the

appliance. Elevated temperatures on the wall or in the air above the appliance can cause melting,

discolouration or damage to decorations, a T.V. or other electronic components.

W415-1352 / B / 08.08.18

1.1 DIMENSIONS

1.2 LISTING APPROVALS

This appliance has been tested in accordance with the CSA Standards for ﬁ xed and location-dedicated electric

room appliances in the United States and Canada. If you need assistance during installation, please contact

your local dealer.

NOTE: This appliance must be electrically wired and grounded

in accordance with local codes or, in the absence of local codes,

with National Electric Code ANSI/NFPA 70-latest edition in the

United States or the Canadian Electric Code, CSA C22.1 in

Canada.

Model Number NEFV38H

Description Wall-Mount

Appliance

Voltage 120V AC~60Hz

Watts Max 1500W

Amps 15 AMP Grounded

Circuit

Appliance Width 17" (432mm)

Appliance Height 38" (965mm)

Appliance Depth 6" (152mm)

Net Weight 14.5kg (32lbs)

Gross Weight 17kg (37lbs)

FRONT VIEW

TOP VIEWSIDE VIEW

6" [152mm]

17" [432mm]

38"

[965mm]

17" [432mm]

21"

[555mm]

32"

[825mm]

1 1/8"

[28mm]

JUNCTION

BOX

BACK VIEW

13" [320mm]

20°

3 1/2"

[89mm]

11" [280mm]

12" [305mm]

W415-1352 / B / 08.08.18

1.3 GENERAL INSTRUCTIONS

4.8A

A. Prior to plugging your appliance into an electrical outlet, verify that the house circuit breakers for the

outlet are on.

B. The appliance may emit a slight, harmless odour when ﬁ rst used. This odour is normal and it is caused

by the initial heating of internal appliance elements and will not occur again.

C. If your appliance does not emit heat, consult the operation section of this manual for further

information.

D. Use with a CSA or UL certiﬁ ed surge protector.

This electric appliance meets the construction and safety standards of H.U.D. for application in manufactured

homes when installed according to these instructions.

WARNING

READ THESE INSTRUCTIONS COMPLETELY BEFORE BEGINNING INSTALLATION. FAILURE TO

FOLLOW THEM COULD CAUSE AN APPLIANCE MALFUNCTION RESULTING IN SERIOUS INJURY

AND/OR PROPERTY DAMAGE.

ALL ELECTRIC APPLIANCES HAVE HOT AND ARCING OR SPARKING PARTS INSIDE. DO NOT USE

IT IN AREAS WHERE GASOLINE, PAINT OR FLAMMABLE LIQUIDS ARE PRESENT.

THIS ELECTRIC APPLIANCE IS TESTED AND LISTED FOR USE ONLY WITH THE OPTIONAL

ACCESSORIES LISTED IN THESE INSTRUCTIONS. USE OF OPTIONAL ACCESSORIES NOT

SPECIFICALLY TESTED FOR THIS ELECTRIC APPLIANCE COULD VOID THE WARRANTY AND/OR

RESULT IN A SAFETY HAZARD.

DO NOT OPEN. RISK OF ELECTRIC SHOCK. NO USER-SERVICEABLE PARTS INSIDE.

DO NOT USE DAMAGED ELECTRICAL CORDS.

SERVICING SHOULD BE DONE ONLY WHILE THE APPLIANCE IS DISCONNECTED FROM THE

POWER SUPPLY CIRCUIT.

TO PREVENT ELECTRIC SHOCK MATCH THE WIDE BLADE OF PLUG TO WIDE SLOT OF

RECEPTACLE AND FULLY INSERT.

As with most electronic devices, your new electric ﬁ replace has been designed to operate at

temperatures between 5°C (41°F) and 35° C (95°F). During the colder winter months, allow the ﬁ replace

to reach room temperature before turning it on.

1.4 UNPACKING AND TESTING APPLIANCE

Carefully remove the appliance from the box. Prior to installing the appliance, test to make sure the appliance

operates properly by plugging the power supply cord into a conveniently located 120 Volt, 15 Amp grounded

outlet.

W415-1352 / B / 08.08.18

1.5 PARTS SUPPLIED

DESCRIPTION ILLUSTRATION QUANTITY

REMOTE & CR2032

BATTERY

CRYSTAL PEBBLES

WALL PLUG

SCREW

CORD COVER

JUNCTION BOX

COVER PLATE

COUPLING

FLAT ELBOW

APPLIANCE

CR2032

W415-1352 / B / 08.08.18

WARNING

2.0 LOCATING APPLIANCE

2.1 GROUNDING APPLIANCE

DUE TO HIGH TEMPERATURES, THIS ELECTRIC APPLIANCE SHOULD BE LOCATED OUT OF

TRAFFIC. KEEP COMBUSTIBLE MATERIALS SUCH AS FURNITURE, PILLOWS, BEDDING, PAPERS,

CLOTHES AND CURTAINS AT LEAST 36" FROM THE FRONT OF THE APPLIANCE.

NEVER LOCATE THIS ELECTRIC APPLIANCE WHERE IT MAY FALL INTO A BATHTUB OR OTHER

WATER CONTAINER.

WEAR SAFETY GLOVES AND SAFETY GLASSES FOR PROTECTION DURING INSTALLATION AND

MAINTENANCE.

TO PREVENT CONTACT WITH SAGGING OR LOOSE INSULATION, THE ELECTRIC APPLIANCE

MUST NOT BE INSTALLED AGAINST VAPOR BARRIER OR EXPOSED INSULATION. LOCALIZED

OVERHEATING COULD OCCUR AND A FIRE COULD RESULT.

DO NOT EXPOSE THE ELECTRIC APPLIANCE TO THE ELEMENTS (SUCH AS RAIN, ETC.)

96.1

GROUNDING METHODS

METAL SCREW

(A)

NOT ALLOWED IN CANADA

GROUNDING

MEANS

ADAPTER

GROUNDING PIN

COVER OF

GROUNDED

OUTLET BOX

(C)

(B)

This appliance is

or use on 120 Volts. The cord has a plug

as shown in (A). An adapter as shown in (C) is available

for connecting three-blade grounding type plugs to two-slot

receptacles. The green grounding lug extending from the

adapter must be connected to a permanent ground such as

a properly grounded outlet box. The adapter should not be

used if a three-slot grounded receptacle is available.

To disconnect appliance, turn controls to off, then remove

plug from outlet.

W415-1352 / B / 08.08.18

3.0 INSTALLATION

Your NEFV38H is a built-in and wall-mounted appliance. Select a suitable location that is not susceptible to

moisture and is away from drapes, furniture and high trafﬁ c areas.

NOTE: Follow all National and local electrical codes.

WARNING

RISK OF FIRE! THE POWER CORD MUST NOT BE PINCHED AGAINST A SHARP EDGE. SECURE CORD TO AVOID

TRIPPING OR SNAGGING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY. DO NOT RUN

CORD UNDER CARPETING. DO NOT COVER CORD WITH THROW RUGS, RUNNERS OR THE LIKE. ARRANGE CORD

AWAY FROM TRAFFIC AREAS AND WHERE IT WILL NOT BE TRIPPED OVER.

RISK OF FIRE! TO PREVENT A POSSIBLE FIRE, DO NOT BLOCK AIR INTAKE OR EXHAUST IN ANY MANNER. DO NOT

USE ON SOFT SURFACES WHERE OPENINGS MAY BECOME BLOCKED.

RISK OF FIRE! DO NOT BLOW OR PLACE INSULATION AGAINST THE APPLIANCE.

THIS ELECTRIC APPLIANCE IS TESTED AND LISTED FOR USE ONLY WITH THE APPROVED OPTIONAL ACCESSORIES.

USE OF OPTIONAL ACCESSORIES NOT SPECIFICALLY TESTED FOR THIS ELECTRIC APPLIANCE COULD VOID THE

WARRANTY AND/OR RESULT IN A SAFETY HAZARD.

IF THE INFORMATION IN THESE INSTRUCTIONS IS NOT FOLLOWED EXACTLY, A FIRE OR EXPLOSION MAY RESULT

CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. DO NOT STORE OR USE GASOLINE OR OTHER

FLAMMABLE VAPORS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE.

THIS APPLIANCE IS HEAVY. IT IS HIGHLY RECOMMENDED THAT TWO PEOPLE INSTALL THIS APPLIANCE.

HEATER VENTS ON THE ELECTRIC APPLIANCE CANNOT, IN ANY WAY, BE COVERED AS IT MAY CREATE A FIRE

HAZARD.

68.5

3.1 MINIMUM CLEARANCE TO COMBUSTIBLES

Measurements are taken from the glass front.

Bottom 20" (500mm) Top 5" (127mm) to mantel

Sides 6" (152mm) Top 5" (127mm) to ceiling

Back 0"

NOTE: The control panel is located on the left hand side of the appliance. Always ensure that there is

access to this control panel.

NOTE: Measured from the rear of the appliance, the ﬁ rst 2 1/2" (63mm) of the appliance body may be

recessed into a combustible wall with 0" (0mm) clearance.

W415-1352 / B / 08.08.18

A. Select a location that is not prone to moisture and is located at least 36"

(914mm) away from combustible materials such as curtain drapes,

furniture, bedding, paper, etc.

B. Before installing the appliance, remove the front glass. Remove the 2

bottom securing screws off the appliance. Pull the bottom of the glass

front away from the appliance and lift up to disengage the top. Remove

and place on a soft non-abrasive surface, refer to Figure 2.

C. Have two people hold the appliance against the wall to determine the

ﬁ nal location.

D. Mark out 5 drill hole locations, refer to Figure 1.

E. Using a 6mm drill bit, drill the 5 holes marked on the wall and ﬁ t with

the supplied wall plugs, have at least one screw in a wall stud. NOTE:

If hole locations are on studs, you do not need to drill or use wall

plugs, simply apply screws directly into studs.

F. Lift the appliance onto the wall, align with the 5 pre-drilled holes.

Secure the appliance to the wall, refer to Figure 3.

G. Sprinkle the crystal embers along the ember bed, refer to Figure 4.

H. Install the glass front onto the appliance and secure with the two

screws from Step B.

I. Check the appliance for stability ensuring it will not pull free from the wall.

3.2 INSTALLING THE APPLIANCE - WALL MOUNT

34" [865mm]

11" [279mm]

6" [152mm]

FIG. 1

FIG. 2

SIDE VIEW

GLASS FRONT

2 SECURING

SCREWS

FIG. 3

FIG. 4

2 BOTTOM

SCREWS

3 TOP

SCREWS

A. Once the rough opening has been prepared, and the power has been routed to the left side of the

recess, the appliance may be installed.

B. With the front glass removed, secure the top and bottom brackets to recess installation location,

refer to "MOUNTING BRACKET INSTALLATION" section.

C. Lift the appliance up to the framing opening, maintaining at least 1/2" (13mm) clearance to the left

side.

D. The electrical connection must be made prior to sliding the appliance into place. (See "HARD WIRE

INSTALLATION" section.)

E. Sprinkle the crystal embers along the ember bed and reinstall the glass front.

F. Install front glass, refer to "GLASS FRONT REMOVAL" section.

NOTE: In order to avoid the possibility of exposed insulation or vapour barrier coming in contact

with the appliance body, it is recommended that the walls of the appliance enclosure be "ﬁ nished"

(ie. drywall/sheetrock), as you would ﬁ nish any other outside wall of a home. This will ensure that

clearance to combustibles is maintained within the cavity.

33"

845mm

13 3/4"

350mm

76mm

MIN

33"

845mm

13 3/4"

350mm

20"

500mm

MIN.

Finishing Material

The appliance can be recessed into the wall a maximum of 2 1/2" (63mm). Select a location that is not prone

to moisture and is located at least 36" (914mm) away from combustible materials such as curtain drapes,

furniture, bedding, paper etc.

3.4 RECESSING INSTALLATION

3.4.1 BUILT-IN FRAMING

(NON-LOAD

BEARING)

W415-1352 / B / 08.08.18

3.4.2 MOUNTING BRACKET INSTALLATION

A. Remove the glass front, refer to "GLASS FRONT REMOVAL" section for removal instructions.

B. Remove the crystals from the appliance prior to installing the mounting brackets.

C. Remove the 4 screws from the top and bottom brackets, refer to Figure 1.

D. Re-arrange the top and bottom brackets so the top bracket is on the bottom and vice versa. Secure

the brackets onto the appliance, refer to Figure 1.

E. Level the appliance and secure the brackets and appliance to the wall.

WALL MOUNT

INSTALL LOCATION

WALL MOUNT

INSTALL LOCATION

RECESS INSTALL

LOCATION

RECESS INSTALL

LOCATION

W415-1352 / B / 08.08.18

FIG. 1

3.5 HARD WIRING INSTALLATION

HARD WIRING CONNECTION

If it is necessary to hard wire this appliance, a qualiﬁ ed electrician must disconnect the existing power cord,

and connect the appliance directly to the house wiring.

This appliance must be electrically connected and grounded in accordance with local codes, if hard wired. In

the absence of local codes, use the current CSA C22.1 CANADIAN ELECTRICAL CODE in Canada or the

current ANSI/NFPA 70 NATIONAL ELECTRICAL CODE in the United States.

WARNING

TURN OFF THE APPLIANCE COMPLETELY AND LET COOL BEFORE SERVICING. ONLY A QUALIFIED SERVICE

PERSON SHOULD SERVICE AND REPAIR THIS ELECTRIC APPLIANCE.

A. Remove the cover plate from the left side of

the appliance by removing the four screws, as

shown above.

COVER PLATE

B. Remove the wire connectors from the power

cord. The power cord may be discarded.

NOTE: Leave enough wire so that the appliance can be removed from the enclosure without

disconnecting the power supply.

C. Take the alternate cover plate, supplied in the manual bag. Punch out the 7/8" (22mm) hole and

install a box connector on the coverplate. Tighten the box connector clamp onto the supply wires.

D. Using the wire connectors, connect the neutral white wires (W) together, then live black wires (B),

and then the ground green wires (G), refer to Figure 3.

E. Install the cover plate using the four screws, as shown in step A.

Fig. 1

Fig. 2

Fig. 3

W415-1352 / B / 08.08.18

4.0 FINISHING

WARNING

POWER SUPPLY SERVICE MUST BE COMPLETED PRIOR TO FINISHING TO AVOID

RECONSTRUCTION.

HEAT VENTS AND AIR OPENINGS CANNOT BE COVERED IN ANY CIRCUMSTANCES.

4.1 CRYSTAL EMBER INSTALLATION

Glass front must be removed and the appliance must be mounted in its ﬁ nal location before the crystal embers

are installed.

A. CLEAN CRYSTAL MEDIA: Crystal embers may have a ﬁ ne oil

residue that needs to be cleaned prior to installation. Clean the

crystal with mild dish soap, drain, rinse thoroughly and dry before

placing into the tray.

B. Carefully place crystal embers into the bottom tray on the front of

the appliance as illustrated. Apply an even layer from side to side.

4.2 GLASS FRONT REMOVAL

A. Remove the 2 bottom securing screws off the appliance. Pull

the bottom of the glass front away from the appliance and lift up

to disengage the top.

B. Tilt the glass front away from the unit. Slightly pull down on the

glass to release from the top catch.

C. Remove and place on a soft non-abrasive surface, as shown in

the illustration.

D. Reverse steps to reinstall the glass front.

SIDE VIEW

GLASS FRONT

2 SECURING

SCREWS

WARNING

FACING AND/OR FINISHING MATERIALS MUST NOT INTERFERE WITH AIR FLOW THROUGH AIR

OPENINGS, LOUVRES OPENINGS, OPERATION OF LOUVRES OR DOORS OR ACCESS FOR

SERVICE. OBSERVE ALL CLEARANCES WHEN APPLYING COMBUSTIBLE MATERIALS.

BEFORE DOOR IS REMOVED TURN THE APPLIANCE OFF AND WAIT UNTIL APPLIANCE IS COOL TO

THE TOUCH. DOORS ARE HEAVY AND FRAGILE SO HANDLE WITH CARE.

75.1

BEFORE FRONT GLASS IS REMOVED TURN THE APPLIANCE OFF AND WAIT UNTIL APPLIANCE IS COOL TO

THE TOAUCH. DOORS ARE HEAVY AND FRAGILE SO HANDLE WITH CARE.

W415-1352 / B / 08.08.18

5.0 OPERATING INSTRUCTIONS

Once the appliance has been plugged into a grounded electrical outlet, it is ready to operate.

NOTE: Ensure the house circuit breakers for the power supply are turned on. The power supply must

be 120 Volts/ 60Hz, 15 Amps.

The control panel is located on the left side of the appliance as illustrated.

The indicates ON / OFF. Push the to turn on the appliance and the ﬂ ame ef

fect.

5.1 MAIN POWER SWITCH & OPERATING CONTROLS

POWER

FLAME & EMBER

LIGHT

HEATER

DECORATIVE LIGHT

TIMER

DIGITAL DISPLAY

NOTE: Control panel

functions operate the

same as the remote

control.

POWER

Turns the appliance ON/OFF.

FLAME & EMBER LIGHT

CONTROL

HEATER LOCK

DECORATIVE LIGHT

HEATER CONTROL

TEMPERATURE SENSOR

TIMER

DIGITAL DISPLAY

Controls flame ON/OFF and the ember light colours which

cycle in the following sequence:

Orange / Blue / Purple / Cycle / Off

Heater button can be locked or unlocked by holding

for 5 seconds.

Turns the heater ON/OFF.

Adjusts heater to a desired temperature based on

environment. Hold for 5 seconds and wait for display to

flash. Cycle through the display value to select desired

temperature.

Push this button to select one of these decorative colour

options: Orange / Blue / Purple / Auto Cycle / Off

Timer can be programed to run appliance / heater for

specific lengths of time (1hr minimum to 9hrs maximum).

Digital display of appliance functions.

Hold 5

seconds

Hold 5

seconds

Display Value

Temperature

0123456789N

18 19

20 21 22 23 24 25 26 27

64 66

68 70 72 74 76 78 80 82

NOTE: When the heater is ON, the flames and embers

can not be turned OFF.

Remote Control:

W415-1352 / B / 08.08.18

6.0 MAINTENANCE

6.1 PCB (CONTROL BOARD)

WARNING

PREPARATION FOR MAINTENANCE

ALWAYS DISCONNECT THE POWER AND ALLOW THE ELECTRIC APPLIANCE TO COOL BEFORE

PERFORMING ANY CLEANING, MAINTENANCE OR RELOCATION OF THIS ELECTRIC APPLIANCE.

TURN CONTROLS TO OFF AND REMOVE PLUG FROM OUTLET OR TURN OFF THE HOUSE

CIRCUIT BREAKER TO ELECTRIC APPLIANCE RECEPTACLE.

To replace the PCB remove the glass door see "GLASS DOOR REMOVAL" section.

A. Remove the crystal media from the appliance.

B. Remove the plastic panel prior to accessing the circuit board.

C. Remove the 4 screws and replace the existing PCB with the new PCB.

6.2 REMOTE BATTERY INSTALLATION

1. Turn over the remote with rear side facing up. Slide

the battery cover off the remote.

2. Place type CR 2032 battery into the remote and

reinstall the battery cover by sliding it into position,

as shown. NOTE: For ease of installation, hold

the battery while sliding the cover onto the

remote

3. Battery cover is secure onto the remote control

when a "CLICKING" noise is heard.

REMOTE

(REAR SIDE)

BATTERY (CR 2032)

BATTERY COVER

W415-1352 / B / 08.08.18

7.0 WIRING DIAGRAM

WARNING

TURN OFF THE APPLIANCE COMPLETELY AND LET COOL BEFORE SERVICING. ONLY A QUALIFIED SERVICE

PERSON SHOULD SERVICE AND REPAIR THIS ELECTRIC APPLIANCE.

FLAME

LED

EMBER BED

LED

MAIN PCB

BLOWER

HEATER

SYNCHRONOUS

MOTOR

HI LIMIT SWITCH

REMOTE

RECIEVER

GND

DECORATIVE

LED

CONTROL

PANEL

W415-1352 / B / 08.08.18

Contact your dealer or the factory for questions concerning prices and policies on replacement parts. Normally

all parts can be ordered through your Authorized dealer / distributor.

FOR WARRANTY REPLACEMENT PARTS, A PHOTOCOPY OF THE

ORIGINAL INVOICE WILL BE REQUIRED TO HONOUR THE CLAIM.

When ordering replacement parts always give the following information:

• Model & Serial Number of appliance

• Installation date of appliance

• Part number

• Description of part

• Finish

* IDENTIFIES ITEMS WHICH ARE NOT ILLUSTRATED. FOR FURTHER INFORMATION, CONTACT YOUR

AUTHORIZED DEALER.

41.1

FAILURE TO POSITION THE PARTS

IN ACCORDANCE WITH THIS

MANUAL OR FAILURE TO USE ONLY

PARTS SPECIFICALLY APPROVED

WITH THIS APPLIANCE MAY

RESULT IN PROPERTY DAMAGE OR

PERSONAL INJURY.

WARNING

For after sales service, please call 1-866-820-8686

8.0 REPLACEMENT PARTS

W415-1352 / B / 08.08.18

ITEMS MAY NOT APPEAR EXACTLY AS ILLUSTRATED

888

PCB

PT-EF11-36

REC

REF. # DESCRIPTIONPART #

BLOWER C/W HEATER

LOG LIGHT LED

FLAME LIGHT LED

PP BOARD

W062-0060

W405-0021

W405-0020

W475-0988

CONTROL PANEL PCB

MAIN PCB

LOG & CRYSTAL GLASS (PLASTIC)

SYNCHRONOUS MOTOR

W405-0022

W190-0075

W190-0076

W135-0587

W435-0073

REFLECTOR SPINDLE

W010-3391

DECORATIVE LED

REMOTE CONTRO

W190-0074

REMOTE RECEIVER

W190-0078

W750-0341

WIRE HARNESS

W300-0197

FRONT GLASS

CORD COVER

W200-0508

HARDWARE KIT

W020-0886

W415-1352 / B / 08.08.18

9.0 TROUBLESHOOTING

SYMPTOM PROBLEM TEST SOLUTION

Dim or no ﬂ ame Flame LED’s are burnt out Inspect the LED’s and replace them if necessary.

Ember bed is not

glowing or dimming

Ember LED’s are burnt out Inspect the ember bed LED’s and replace them if necessary.

No warm air coming

out of appliance

Room temperature is higher

than the appliance setting (if

it is set to room temperature)

Heater is burnt out

Reset temperature setting.

Inspect the burner and heater assembly (W062-0047) and

replace it if necessary.

Appliance turns off

and will not turn on

Appliance has overheated

and safety thermal switch has

tripped

Turn off the Main Switch, allow appliance to cool for 15 minutes

to reset the thermal switch, then turn it on.

House circuit breaker has

tripped

Appliance’s fuse has blown

Reset house circuit breaker.

Replace the fuse.

Appliance will not

come on when

switch is ﬂ ipped to

Appliance is not plugged into

an electrical outlet

Check plug and plug it in.

Appliance has overheated

and safety thermal switch has

tripped

Circuit board is burnt out

Turn off the Main Switch, allow appliance to cool for 15

minutes, then turn it on.

Inspect the circuit board and replace it if necessary.

Remote control

does not work

Low batteries Replace batteries in remote control.

Heater shuts off

automatically

Room is too warm The heater has a built-in thermostat so it will shut off

automatically once the pre-set temperature is reached. It will

also turn on automatically if the room temperature drops below

the pre-set temperature.

WARNING

TURN OFF THE APPLIANCE COMPLETELY AND LET COOL BEFORE SERVICING. ONLY A

QUALIFIED SERVICE PERSON SHOULD SERVICE AND REPAIR THIS ELECTRIC APPLIANCE.

Unplug power cord and allow appliance to cool for 15 minutes,

then plug in the power cord and turn the power ON.

Unplug power cord and allow appliance to cool for 15 minutes,

then plug in the power cord and turn the power ON.

W415-1352 / B / 08.08.18

10.0 WARRANTY

NAPOLEON® warrants its products against manufacturing defects to the original purchaser only. Registering your warranty is not necessary.

Simply provide your proof of purchase along with the model and serial number to make a warranty claim. NAPOLEON® reserves the right to have

its representative inspect any product or part thereof prior to honouring any warranty claim. Provided that the purchase was made through an

authorized NAPOLEON® dealer your appliance is subject to the following conditions and limitations:

Warranty coverage begins on the date of original installation.

This factory warranty is non-transferable and may not be extended whatsoever by any of our representatives.

Installation must be done in accordance with the installation instructions included with the product and all local and national building and ﬁ re codes.

This limited warranty does not cover damages caused by misuse, lack of maintenance, accident, alterations, abuse or neglect and parts installed

from other manufacturers will nullify this warranty.

This limited warranty further does not cover any scratches, dents, corrosion or discoloring caused by excessive heat, abrasive and chemical

cleaners nor chipping on porcelain enamel parts, mechanical breakage of PHAZER™ logs.

In the ﬁ rst year only, this warranty extends to the repair or replacement of warranted parts which are defective in material or workmanship provided

that the product has been operated in accordance with the operation instructions and under normal conditions.

NAPOLEON® will not be responsible for installation, labour or any other expenses related to the reinstallation of a warranted part and such

expenses are not covered by this warranty. Notwithstanding any provisions contained in the Limited Warranty, NAPOLEON’s responsibility under

this warranty is deﬁ ned as above and it shall not in any event extend to any incidental, consequential or indirect damages.

This warranty deﬁ nes the obligations and liability of NAPOLEON® with respect to the NAPOLEON® electric appliance and any other warranties

expressed or implied with respect to this product, its components or accessories are excluded.

NAPOLEON® neither assumes, nor authorizes any third party to assume, on its behalf, any other liabilities with respect to the sale of this product.

Any damages to appliance, brass trim or other component due to water, weather damage, long periods of dampness, condensation, damaging

chemicals or cleaners will not be the responsibility of NAPOLEON®.

The bill of sale or copy will be required together with a serial number and a model number when making any warranty claims from your authorized

dealer. The warranty registration card must be returned within fourteen days to register the warranty.

NAPOLEON® reserves the right to have its representative inspect any product or part thereof prior to honouring any warranty claim.

All parts replaced under the Limited Warranty Policy are subject to a single claim.

All parts replaced under the warranty will be covered for a period of 90 days from the date of their installation.

The manufacturer may require that defective parts or products be returned or that digital pictures be provided to support the claim. Returned

products are to be shipped prepaid to the manufacturer for investigation. If a product is found to be defective, the manufacturer will repair or

replace such defect.

Before shipping your appliance or defective components, your dealer must obtain an authorization number. Any merchandise shipped without

authorization will be refused and returned to sender.

Shipping costs are not covered under this warranty.

Additional service fees may apply if you are seeking warranty service from a dealer.

2.5B

NAPOLEON® electric appliances are manufactured under the strict Standard of the world recognized

ISO 9001 : 2008 Quality Assurance Certiﬁ cate.

NAPOLEON® products are designed with superior components and materials, assembled by trained craftsmen who take

great pride in their work. Once assembled the complete appliance is thoroughly inspected by a qualiﬁ ed technician before

packing to ensure that you , the customer, receive the quality product that you expect from NAPOLEON®.

Electrical components and wearable parts such as fan/heater, motors, switches, nylon bearing components and remote

controls are covered and NAPOLEON® will provide replacement parts free of charge during the ﬁ rst year of limited warranty.

Light bulbs and fuses are NOT covered by the warranty.

Any labour related to warranty repair is not covered.

* Construction of models vary. Warranty applies only to components included with your speciﬁ c appliance.

NAPOLEON® ELECTRIC APPLIANCE LIMITED WARRANTY

CONDITIONS AND LIMITATIONS

ALL SPECIFICATIONS AND DESIGNS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE DUE TO ON-GOING PRODUCT IMPROVEMENTS.

NAPOLEON® IS A REGISTERED TRADEMARK OF WOLF STEEL LTD.

La page charge ...

NAPOLEON NEFV38H Le manuel du propriétaire

Marque: NAPOLEON

Modèle: NEFV38H

Catégorie: Cheminées

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: NAPOLEON NEFV38H Owner's manual

NAPOLEON NEFV38H Le manuel du propriétaire

NAPOLEON NEFV38H Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents