Episode ECA-70AMP-2D-150A Le manuel du propriétaire
- Catégorie
- Équipement musical supplémentaire
- Taper
- Le manuel du propriétaire
Ce manuel convient également à
Pg. 1
©2014 Episode™
Installation Manual 2- Channel 70 Volt Power Ampliers
ECA-70AMP-2D-150A ECA-70AMP-2D-300A
ECA-70AMP-2D-500A
Pg. 3
©2014 Episode™
Pg. 2
©2014 Episode™
Warning: To reduce the risk of re or electric shock, do not expose this apparatus to rain or moisture.
The lightning ash with arrowhead symbol, within an equilateral triangle, is intended to
alert the user to the presence of un-insulated dangerous voltage within the product’s
enclosure that may be of sufcient magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equivalent triangle is intended to alert the user to
the presence of important operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
ampliers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The
wide blade or the third prong are provided for your safety. If the provided plug does not t into your outlet,
consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and
the point where they exit from the apparatus.
11. Only use attachments/accessories specied by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specied
by the manufacturer, or sold with the apparatus. When a cart is
used, use caution when moving the cart/apparatus combination
to avoid injury from tip-over. (See Figure on Right)
13. Unplug this apparatus during lightning storms or when unused
for long periods of time.Refer all servicing to qualied service
personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
14. This product employs a Class I (or grounded) construction and shall be connected to a mains socket outlet
with a protective earthed (or ground) connection.
15. DO NOT EXPOSE THIS EQUIPMENT TO DRIPPING OR SPLASHING AND ENSURE THAT NO OBJECTS
FILLED WITH LIQUIDS, SUCH AS VASES, ARE PLACED ON THE EQUIPMENT.
16. TO COMPLETELY DISCONNECT THIS EQUIPMENT FROM THE AC MAINS, DISCONNECT THE POWER
SUPPLY CORD PLUG FROM THE AC RECEPTACLE.
17. THE MAIN PLUG OF THE POWER SUPPLY CORD SHALL REMAIN READILY OPERABLE.
18. CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE COVER. NO USER SERVICE-
ABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
1. Important Safety Instructions
Avertissement:Pour réduire le risque d’ incendie ou un choc électrique, ne pas exposer cet appareil
à la pluie ou à l’humidité.
1. Lisez ces instructions .
2. Conservez ces instructions .
3. Respectez tous les avertissements .
4. Suivez toutes les instructions .
5. Ne pas utiliser cet appareil près de l’eau .
6. Nettoyer avec un chiffon sec .
7. Ne pas bloquer les ouvertures de ventilation . Installer conformément aux instructions du fabricant .
8. Ne pas installer près de sources de chaleur telles que des radiateurs , registres de chaleur , poêles ou autres
appareils (incluant les amplicateurs) qui produisent de la chaleur .
9. Ne pas contourner le dispositif de sécurité de la che polarisée ou de mise à la terre . Une che polarisée
possède deux lames dont une plus large que l’autre . Une che de terre a deux lames et une troisième broche
de mise à la terre . La lame large ou la troisième broche sont fournies pour votre sécurité . Si la che fournie ne
rentre pas dans votre prise, consultez un électricien pour le remplacement de la prise obsolète .
10. Protégez le cordon d’alimentation ne soit piétiné ou pincé, en particulier au niveau des ches , des prises de
courant et le point de sortie de l’appareil.
11. N’utilisez que des xations / accessoires spéciés par le fabricant .
12. Utilisez uniquement avec le chariot , le trépied, le support ou la table spécié
par le fabricant, ou vendu avec l’appareil . Quand un chariot est utilisé,
faites attention en déplaçant l’ensemble chariot / appareil pour éviter les
blessures en cas de renversement . ( Voir dessin à droite )
13. Débranchez cet appareil pendant les orages ou lorsqu’il n’est pas utilisé
pendant de longues périodes de time.Refer à un technicien qualié
personnel . Une réparation est nécessaire lorsque l’appareil a été
endommagé de quelque façon que ce cordon d’ alimentation ou la prise est
endommagé , du liquide a été renversé ou des objets sont tombés dans l’
appareil, l’appareil a été exposé à la pluie ou à l’humidité ,
ne fonctionne pas normalement , ou s’il est tombé .
14. Ce produit utilise une classe I ( ou la terre) construction et doit être raccordé à une prise de courant mise à la
terre avec une protection ( ou masse) .
15. NE PAS EXPOSER CET APPAREIL À éclaboussures et s’assurer qu’aucun OBJET REMPLI DE LIQUIDE , TEL
QU’UN VASE , sont placés sur le MATÉRIEL .
16. Pour déconnecter totalement cet appareil du secteur , débranchez la CORDON D’ALIMENTATION che de la prise
secteur.
17. LA PRISE PRINCIPALE DU CORDON D’ALIMENTATION doit rester facilement accessible .
18. ATTENTION : POUR RÉDUIRE LE RISQUE DE CHOC ÉLECTRIQUE , NE PAS RETIRER . NO réparable par
l’utilisateur pièces à l’intérieur . CONFIER L’ENTRETIEN DE PERSONNEL QUALIFIÉ .
1. Consignes de Sécurité Importantes
Le ash de foudre avec le symbole de pointe de èche, dans une triangle équilaterale,
est prévu pour alerter l’utilisateur à la présence de la tens ion dangereuse non isolée
dans la clôture du produit qui peut être de la grandeur sufsante pour constituer un
risque de décharge électrique aux personnes.
Le point d’exclamation dans une triangle équilaterale est prévu pour alerter l’utilisateur
à la présence des instructions importantes de fonctionnement et d’entretien (entretien)
dans la littérature accompagnant l’appareil.
Pg. 5
©2014 Episode™
Pg. 4
©2014 Episode™
1. Important Safety Instructions 2
2. Overview 5
3. Features 5
4. Tools 5
5. Speaker Recommendation 5
6. Front Panel 6
7. Rear Panel 6
8. Bottom Panel 7
9. Positioning the Amplifier 8
9.1. Shelf Mounting 8
9.2. Rack Mounting 8
10. Connections 9
10.1. Terminating Wire in Set-Screw Connectors 9
10.2. Balanced Input 9
Connecting a Balanced Wire 9
Connecting an Unbalanced Wire 9
10.3. Unbalanced Connections 9
10.4. Using Loop Out 9
11. Amplifier Power Control 10
11.1. Master Power Switch 10
11.2. Front Panel Power Button 10
11.3. Power ON Mode 10
11.4. 12 Volt Trigger 10
11.5. AUTO (Audio Sense) 10
12. Volume Calibration 11
12.1 Calibration Setup Tips 11
Distorted Audio at Normal Volume 11
Inline Volume Controls “Thump” or Play Source Audio in the Walls 11
13. Application Diagrams 12
13.1.Single Source with Stereo Output 12
13.2.Two Sources with Two Mono Output Zones 12
14. Specifications 13
15. Dimensions 13
16. Troubleshooting 14
17. Contacting Technical Support 14
18. Warranty 15
Table of Contents
Episode
®
is one of the most highly-regarded brands of ampliers available today. We appreciate your business
and we stand committed to providing our customers with the highest degree of quality and service in the industry.
The ECA-70AMP-2D 2-channel, 70-volt digital power amplier series is designed for applications requiring
two separate channels for stereo audio, or two zones of audio requiring different sources or levels. With low
heat output thanks to digital amplication, and massive power output in a small, 1U package, these ampliers
are guaranteed to perform.
1U Rack Height
Save space in already-crowded rack with the rst 1U-sized 70 volt amplier on the market.
Digital 70 Volt Amplication
State-of-the-art electronics provide clean sounding audio and efcient operation in a lightweight package.
Less than half the power consumption and weight of equivalent 2 channel 70 volt ampliers.
Two Zone Audio
Isolated inputs and outputs for each zone can be used for 2 separate mono channels, stereo left and right
channels, or 2 channels of the same source.
Independent Volume Controls
Each input level may be adjusted individually.
12V Trigger and Audio Sense Control
Integrated power control allows the amplier to be switched on and off at will by other equipment, or to
automatically turn on when it senses signal on either input. Another rst for 70 volt ampliers.
Balanced and Unbalanced Inputs
Attach any source quickly and easily. Standard unbalanced RCA inputs are accompanied by balanced inputs
using set-screw connectors for universal compatibility.
• #2 Philips Screwdriver
• Wire Strippers
The ECA-70AMP-2D amplier is only meant to be used with 70 Volt loudspeakers. Use any combination
of speakers as long as the sum of the wattage does not exceed the rated wattage of the speaker output.
2. Overview
3. Features
4. Tools
5. Speaker Recommendation
Pg. 7
©2014 Episode™
Pg. 6
©2014 Episode™
1. Loop Outputs 1 & 2
Unbalanced mono RCA connections for sending
audio to other equipment.
2. Unbalanced Inputs 1&2
Unbalanced mono RCA input connections for
connection of sources.
3. Balanced Inputs 1 & 2
Set-screw connections for sources with balanced
output.
4. Input Level Adjustment Dials
Attenuate input volume levels. Turn counter-
clockwise to decrease and clockwise to increase
the level.
5. Speaker Output Connections
Set-screw connections for speaker output
channels 1 & 2. Accommodates 22-12AWG
wire.
6. Master Power Switch
Rocker switch to control master power state.
Must remain “On” during amplier use.
7. IEC Power Cord
Detachable power for amplier.
8. Power Mode Selector Switch
Set the amplier for control via the front power
button (ON), 12V trigger (TRIGGER DC 12V), or
audio sense (AUTO).
9. 12 Volt Trigger Loop In and Out
When 4.5-15 Volts DC are applied to Loop In,
amplier will turn on. When voltage is dropped,
amplier turns back off. Loop out allows other
equipment to be controlled from the same 12 volt
signal.
10. AC Fuse
Replaceable main power fuse.
POWER 2
1
PROT -20 -10 CLIP-30
ECA-70AMP-2D-300A
1 2
3
1. Power Switch with LED Indicator
Momentary switch for manual control of standby power mode. Only functions when the power mode is
set to “ON”.
BLUE – On.
RED – Standby.
2. Protection LED
Indicates whether a channel is operating correctly or is in protection.
BLUE – Normal.
RED – Protection. (Indicates an issue with installation or setup)
3. Output Level Meter
Level meter ashes green to indicate current output level for each channel. LEDs will illuminate green
accordingly as levels ranging from -30dB to -10dB are played. If a channel is clipping, the red CLIP LED
will illuminate during periods of clipping (turn down input level immediately if clipping occurs).
6. Front Panel
7. Rear Panel
Note: ECA-70AMP-2D-300A shown. All models share this layout, but have different specs for Power and Fuse ratings.
OUTIN
ON
POWER
MODE
LOOP OUT
LEVEL
OUTPUTS
0V 0V70V 70V
OF
ONLY
CAUTION:
TYPE.
ATTENTION:
INPUTS
CH1
CH2
CH2
CH2CH1
CH1
CH2CH1
ON
OFF
MASTER
POWER
FUSE TYPE:
T4AL 250V
T8AL 250V
115/230V
VOLTAGE
SWITCH
COMMERCIAL
AUDIO
EQUIPMENT
E33024 7
AUDIO
1 2
3 4 5 6 7
9 108
*Terminals marked with are hazardous live and external wiring connected to these terminals requires
installation by an instructed person or the use of ready-made leads or cords.
1. Input Voltage Switch
Set the input voltage for 115V or 230VAC operation based on the voltage available.
Note: The ECA-70AMP-2D includes an IEC cable meant for use with a NEMA 5-15 receptacle supplying
115V AC power. For countries utilizing 230V AC power, the cable can be swapped to the correct
cable for that region. When using the 230V AC input voltage setting, change the fuse in the
amplier from the included to a fuse rated for 230V AC. See the Specications on page <Speci-
cations> for the correct fuse type for each model. Using the wrong fuse could result in blown
fuses or damage to the amplier, which is not covered by the warranty.
8. Bottom Panel
INPUT
VOLTAGE
51
1
INPUT
VOLTAGE
51
1
1
Pg. 9
©2014 Episode™
Pg. 8
©2014 Episode™
Episode ampliers are designed to help deliver a great audio experience that makes your music come alive for
years to come. However, where you place the amplier can have a large effect on the performance that you
receive and the life of the unit.
• Be sure that the unit is in a well-ventilated area
that provides adequate cooling.
• Do not block the cooling vents located on both
sides of the unit.
• Do not place the unit on carpeting or any
similar material.
• Do not install the unit near a source of heat, or
in an extremely humid or wet location.
• If your installation lacks good air ow (such as
solid cabinet doors or wall-mounted racks), it
may be necessary to create ventilation to allow
outside air into the space.
• Allow a minimum of 5” of free air space above
the unit.
• Allow a minimum of 3” of free air space on
either side of the unit. (Does not apply to rack
mounting)
9. Positioning the Amplifier
POWER 2
1
PROT -20 -10 CLIP-30
ECA-70AMP-2D-300A
3in.3in.
5in.
Minimum of 3"
free air space on
each side.
Minimum of 5"
free air space
above.
9.1. Shelf Mounting
9.2. Rack Mounting
1. Remove the amplier’s four feet from the bottom of the chassis.
Note: DO NOT place the screws back into the chassis. Without the feet, the length of the screw may
touch internal components and affect the performance of the amplier.
2. Attach the included rack-mount ears to the front sides of the amplier chassis.
3. Securely mount the amplier into an equipment rack. The amplier will occupy 1U of rack space.
4. Even though the amplier produces very little heat, it is always wise to leave ventilation between
components.
POWER 2
1
PROT -20 -10 CLIP-30
ECA-70AMP-2D-300A
Remove Feet
Attach Ears using Supplied Screws
(4 on Each)
2in.
10. Connections
10.1. Terminating Wire in Set-Screw Connectors
1. Strip the outer jacket of the cable (if applicable) back about 2”, and then strip the insulation of each wire
back ¼“ to expose the bare copper.
2. Loosen the set screws on the connector using a 1/8” at blade screwdriver.
3. Twist the copper strands in conductor each clockwise, insert them into the correct holes, and tighten
the screws. Do not allow any strands of copper to touch and cause short circuits between the termi-
nals.
10.2. Balanced Input
Use the balanced input to connect balanced or unbalanced cables to the amplier.
Positive (+)
Negative (-)
Shield
CH 1
CH 2
Shield
Positive (+)
Negative (-)
Positive (+)
Negative (-)
CH 1
CH 2
Positive (+)
Negative (-)
Shield
Shield
Note Jumper between Shield and Negative (-)
10.3. Unbalanced Connections
The unbalanced Line IN input utilizes standard RCA cables for connection of sources. Connect a
source to each channel through its respective mono input. Use the Loop Out ports to connect to
more ampliers or other equipment.
LOOP OUT
OUTPUTS
CAUTION:
INPUTS
ON
115/230V
OUTIN
AUTO
ON
POWER
MODE
ANSI/UL STD.60065
Intertek
WARNING:
AVIS:
LEVEL
0V 0V70V 70V
OF
ONLY
TYPE.
ATTENTION:
CH1
CH2
CH2
CH2CH1
CH1
CH2CH1
OFF
MASTER
POWER
FUSE TYPE:
T4AL 250V
T8AL 250V
VOLTAGE
SWITCH
E330247
Unbalanced
Loop Out 1 & 2
Unbalanced
Line IN 1 & 2
10.4 Using Loop Out
The Loop Out connections on the ECA-70AMP-2D amplier may be used to send audio signal to
other equipment, or to the other channel of the amplier. The Loop Out will carry audio signal out
from the unbalanced input OR the balanced input of the channel.
LOOPOUT
OUTPUTS
CAUTION:
INPUTS
ON
115/230V
OUTIN
AUTO
ON
POWER
MODE
LEVEL
0V 0V70V 70V
OF
ONLY
TYPE.
ATTENTION:
CH1
CH2
CH2
CH2CH1
CH1
CH2CH1
OFF
MASTER
POWER
FUSETYPE:
T4AL250V
T8AL250V
VOLTAGE
SWITCH
E33024 7
From Source
Balanced or unbalanced input can be looped out
LOOPOUT
OUTPUTS
CAUTION:
INPUTS
ON
115/230V
OUTIN
AUTO
ON
POWER
MODE
LEVEL
0V 0V70V 70V
OF
ONLY
TYPE.
ATTENTION:
CH1
CH2
CH2
CH2CH1
CH1
CH2CH1
OFF
MASTER
POWER
FUSETYPE:
T4AL250V
T8AL250V
VOLTAGE
SWITCH
E33024 7
Connect Channel 1 Loop Out to Channel 2 Loop In
for two channels with one source, or to other equipment
Pg. 11
©2014 Episode™
Pg. 10
©2014 Episode™
11.1. Master Power Switch
The master power toggle switch at the back of the unit controls the main power. If this is turned off,
the amplier will not respond to any control method. This switch should be left in the ON position
after installation and setup is nished unless the amplier will not be used for an extended period
of time or is being serviced. For everyday use, decide on one of the options below.
Use the Power Mode switch (below the Master Power switch) to select the desired power control
mode.
11.2. Front Panel Power Button
When the amplier is powered On, the power button will illuminate solid blue. When it is in Stand-
by, the power button will be red.
Note: The front panel Power button only controls the amplier when the power mode selector
switch is set to Power ON.
11.3. Power ON Mode
For manual control of the amplier power state, set the Power Mode switch to POWER On. Press
the front panel Power button to toggle between Stand-by and On.
11.4. 12 Volt Trigger
Some audio sources and custom remote control systems can use a 12V DC trigger output to
control the power state of an amplier. The ECA-70AMP-2D is equipped with 12V DC trigger
inputs and outputs to allow for trigger control and daisy chaining for control of more than one
amplier.
To utilize the 12V DC trigger function, set the Power Mode switch to the right to TRIGGER (closest
to the 12V trigger connections) and attach a mono mini cable between the 12V trigger output of
the controlling device and the TRIGGER DC 12V IN port on the ECA-70AMP-2D. Connect to
other devices by connecting them to the OUT port on the amplier with a mono-mini cable.
11.5. AUTO (Audio Sense)
Setting the Power Mode switch to AUTO will allow the amplier to monitor the level of signal
coming in from the source connection and power on when the level is high enough to be process
as an audio signal. No further setup is needed.
When a source attached to any input generates a signal, the amplier will power on, and will
remain on as long as the signal is maintained. After 20 minutes of inactivity on all inputs, the
amplier will power down and return to Stand-by mode until a signal is received again.
11. Amplifier Power Control
Cable 3.5mm Mono-mini
Tip 4.5-15v DC (constant during use)
Sleeve Ground/Common
12. Volume Calibration
Follow these directions to calibrate the LEVEL setting in relation to the source input volume and inline
volume control level (if applicable) for the best sounding and most reliable installation.
1. Connect all speaker and audio source wiring and congure the amplier. Connect power to the
amplier but leave it turned Off at the Master Power Switch.
2. (If applicable) Set all volume controls to their maximum volume setting.
3. Set the LEVEL for each zone in use to baseline by turning the knob counterclockwise to its
minimum limit, and then turning it back up about ¼ turn. Set the LEVEL for any unused zones to
minimum (counterclockwise).
4. Power on the amplier and the source to be used. Play audio typical of what will be played
in the zone. Set the volume of the source to around half of its volume. If the audio becomes
distorted, turn the volume back to a point where audio is clear.
5. Set the LEVEL adjustment for the zone to a level where the volume is slightly above normal
listening level. If the audio becomes distorted, experiment with changes to the source volume
and the LEVEL adjustment until audio is clear and slightly too loud.
6. Now the volume level of each zone is matched to the volume of the source input. Adjust the
level of audio back to a comfortable level by adjusting the inline volume control (if equipped) or
the source volume.
12.1. Calibration Setup Tips
The following common issues may occur with a poorly calibrated system. Use the tips listed to
identify and correct these problems:
Distorted Audio at Normal Volume
If the LEVEL adjustment for a zone is set too high to compensate for low source volume, distortion
can occur in the form of background noise or poor audio quality. This will be heard as a steady
hissing or humming behind music, clipping of signal, or distortion of highs and lows.
To eliminate this issue, re-adjust the volume levels by starting back at baseline settings and re-
adjusting the nal volume so that a maximum comfortable volume level can be reached with no
distortion while using the source volume or inline control.
Inline Volume Controls “Thump” or Play Source Audio in the Walls
If inline volume controls are thumping in the wall, then the amplier and the source volume levels
are set too high and the volume controls are being used to attenuate too much power from the
speakers. This causes the entire system to work harder, and can reduce reliability and sound
quality.
Inline volume controls should be calibrated in relation to source/amplier volume so that they are
one or two adjustment levels away from their maximum setting when audio heard in the room is
at the normal listening level. This will leave one to three settings above normal level for use if a
little extra volume is needed.
Pg. 13
©2014 Episode™
Pg. 12
©2014 Episode™
13. Application Diagram
See the examples of applications below. These diagrams illustrate typical uses of the ECA-70AMP-2D
amplier.
13.1 Single Source with Stereo Output
Left
(CH 1)
Right
(Ch 2)
LOOP OUT
OUTPUTS
CAUTION:
INPUTS
ON
115/230V
OUTIN
AUTO
ON
POWER
MODE
LEVEL
0V 0V70V 70V
OF
ONLY
TYPE.
ATTENTION:
CH1
CH2
CH2
CH2CH1
CH1
CH2CH1
OFF
MASTER
POWER
FUSE TYPE:
T4AL 250V
T8AL 250V
VOLTAGE
SWITCH
E3302 47
Ch 1 Loop Out
Left to CH 1
Right to CH 2
For 70v Subwoofers,
visit our website. For
Subwoofer wiring
recommendations,
please call Tech
Support.
13.2 Two Sources with Two Mono Output Zones
Zone 2
(CH 2)
Zone 1
(Ch 1)
LOOP OUT
OUTPUTS
CAUTION:
INPUTS
ON
115/230V
OUTIN
AUTO
ON
POWER
MODE
LEVEL
0V 0V70V 70V
OF
ONLY
TYPE.
ATTENTION:
CH1
CH2
CH2
CH2CH1
CH1
CH2CH1
OFF
MASTER
POWER
FUSE TYPE:
T4AL 250V
T8AL 250V
VOLTAGE
SWITCH
E3302 47
Source 1
(Unbalanced RCA)
Source 2
(Balanced Input)
From Automaton System
12V Trigger Output
LOOP OUT option
for use with
another amp.
LOOP OUT option
for use with
another amp.
ECA-70AMP-2D-150 ECA-70AMP-2D-300 ECA-70AMP-2D-500
Continuous Power
Output (All Channels)
150w per channel @
70V
300w per channel @
70V
500w per channel @
70V
Inputs per Channel 1 unbalanced (set-screw) and 1 balanced (RCA)
Input Sensitivity 1V
Input Impedance 10KΩ (unbalanced); 20KΩ ( balanced)
AUTO ON Sensitivity 2.5mV
12 Volt Trigger Input 4.5-12V DC; 10K Ω
12 Volt Trigger Output 12V DC; 10mA
T.H.D. 0.03%
S/N ratio 95db A-weighted
Frequency Response 50 Hz to 20KHz
Distortion 0.1% THD 20 Hz-20 kHz
Input Voltage 115V AC/230V AC
Fuse 115V AC T4AL 250V T8AL 250V T10AL 250V
230V AC T2.5AL 250V T4AL 250V T5AL 250V
Power Consumption 400 watts 800 watts 1200 watts
Dimensions (Inches) 17”W x 2.3”H x 11”D
Weight 7.8 lbs 8.1 lbs 8.4 lbs
Certication Meets FCC Part 15, UL EN60065
14. Specifications
15. Dimensions
POWER 2
1
PROT -20 -10 CLIP-30
ECA-70AMP-2D-300A
19.00in.
17.40in.
1.75in.
2.30in.
11.00in.
POWER 2
1
PROT -20 -10 CLIP-30
ECA-70AMP-2D-300A
19.00in.
17.40in.
1.75in.
2.30in.
11.00in.
Pg. 15
©2014 Episode™
Pg. 14
©2014 Episode™
16. Troubleshooting
Amplier will not turn on. • Power cable to the amplier is incorrectly connected or
plugged into an outlet that does not have power. Check con-
nections and verify power on the outlet.
• Main Power Fuse is blown. Replace fuse and ensure power
outlet is providing the correct power and polarity for the
amplier.
POWER LED is red. • Amplier is in Protection mode. Short circuit on input or
output or too much current being drawn on speaker output.
Verify all wiring and connections.
• Calculate load attached to amp and congure so that imped-
ance or wattage output is within specication.
• Amplier is overheating. Unplug amp and let cool. Install per
instructions in manual, “Positioning the Amplier”.
Hum or buzzing sound is heard. • Check RCA input cables by removing them one at time (pow-
ering down the amplier before disconnecting) and checking
to see if a connection or cable is to blame.
No audio from speakers. • Verify speakers and wiring connections. Bypass volume
controls and test output with one speaker on known good
wire run.
• Verify correct source operation and input wiring. Turn volume
in source up to an audible level.
• Is Power LED red? If so, see section above, “POWER LED
is RED”.
No sound from microphone
input.
• Set the phantom power switch to the correct mode for micro-
phone. Verify with microphone manufacturer.
CLIP LED illuminates some or all
of the time.
• Turn down the input volume. The amplier is trying to push
too much power to the speakers.
Note: If any of the troubleshooting methods listed above do not resolve the issue, please contact
our Technical Support department.
Phone (866) 838-5052
Email support@snapav.com
17. Contacting Technical Support
18. Warranty
2-Year Limited Warranty
Episode
®
Amplier Products have a 2-Year Limited Warranty. This warranty
includes parts and labor repairs on all components found to be defective in material
or workmanship under normal conditions of use. This warranty shall not apply to
products that have been abused, modied, or disassembled. Products to be repaired
under this warranty must be returned to SnapAV or a designated service center with
prior notication and an assigned return authorization number (RA).
2
year
Pg. 16
©2014 Episode™
Rev: 140417-1430
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
Episode ECA-70AMP-2D-150A Le manuel du propriétaire
- Catégorie
- Équipement musical supplémentaire
- Taper
- Le manuel du propriétaire
- Ce manuel convient également à
dans d''autres langues
Documents connexes
-
Episode ESA-70V2CH-500W Guide d'installation
-
Episode EA-AMP-HYB-2D-1000 Manuel utilisateur
-
-
-
-