Rockford Fosgate RFA-514 Manuel utilisateur

Marque: Rockford Fosgate

Modèle: RFA-514

Catégorie: Haut-parleurs de voiture

Taper: Manuel utilisateur

Ce manuel convient également à

®®

PUNCH

AUDIOPHILE

SYSTEM

RFA-414

RFA-514

RFA-614

INSTALLATION & OPERATION

Dear Customer,

Congratulations on your purchase of the world's finest brand of car audio speakers. At

Rockford Fosgate we are fanatics about musical reproduction at its best, and we are

pleased you chose our product. Through years of engineering expertise, hand craftsman-

ship and critical testing procedures, we have created a wide range of products that

reproduce music with all the clarity and richness you deserve.

For maximum performance we recommend you have your new Rockford Fosgate

product installed by an Authorized Rockford Fosgate Dealer, as we provide specialized

training through Rockford Technical Training Institute (RTTI). Please read your

warranty and retain your receipt and original carton for possible future use.

Great product and competent installations are only a piece of the puzzle when it comes

to your system. Make sure that your installer is using 100% authentic installation

accessories from Connecting Punch in your installation. Connecting Punch has

everything from RCA cables and speaker wire to Power line and battery connectors.

Insist on it! After all, your new system deserves nothing but the best.

To add the finishing touch to your new Rockford Fosgate image order your Rockford

wearables, which include everything from T-shirts and jackets to hats and sunglasses.

To get a free brochure on Rockford Fosgate products and Rockford accessories, in the

U.S. call 602-967-3565 or FAX 602-967-8132. For all other countries, call +001-602-

967-3565 or FAX +001-602-967-8132.

If, after reading your manual, you still have questions regarding this product,

we recommend that you see your Rockford Fosgate dealer. If you need further

assistance, you can call us direct at 1-800-795-2385. Be sure to have your serial

number, model number and date of purchase available when you call.

PRACTICE SAFE SOUND™

CONTINUOUS EXPOSURE TO SOUND PRESSURE LEVELS OVER

100dB MAY CAUSE PERMANENT HEARING LOSS. HIGH

POWERED

AUTOSOUND SYSTEMS MAY PRODUCE SOUND

PRESSURE

LEVELS WELL OVER 130dB. USE COMMON SENSE

AND

PRACTICE SAFE SOUND.

The serial number can be found on the outside of the box. Please record it in

the space provided below as your permanent record. This will serve as

verification of your factory warranty and may become useful in recovering your

product if it is ever stolen.

Serial Number: ________________________________

Model Number:________________________________

Welcome to Rockford Fosgate! This manual is designed to provide

information for the owner, salesperson and installer. For those of you

who want quick information on how to install this product, please turn

to the

Installation Section

of this manual or refer to the icons listed

below. Other information can be located by using the Table of Contents.

We, at Rockford Fosgate, have worked very hard to make sure all the

information in this manual is current. But, as we are constantly finding

new ways to improve our product, this information is subject to change

without notice.

GETTING STARTED

Sections marked

TROUBLESHOOTING

include recommendations

for curing

installation problems

® ®

TROUBLE-

TABLE OF CONTENTS

Introduction ...............................................................................................

Amplifier Accessory Pack.........................................................................1

Technical Design Features ....................................................................... 2

Design Features........................................................................................5

Installation Considerations ....................................................................... 7

Mounting Location...................................................................................8

Battery and Charging................................................................................9

Wiring the System .................................................................................... 9

Using the XCard.....................................................................................12

Resistor Chart.........................................................................................13

Installation .............................................................................................14

System Diagrams.................................................................................... 18

Rockford Fosgate Accessories................................................................. 22

Troubleshooting .....................................................................................26

Dynamic Power Measurements..............................................................29

Specifications.........................................................................................31

Warranty Information.............................................................................33

International Information........................................................................34

Sections marked

INSTALLATION

include “slam dunk”

wiring connections

INTRODUCTION

This manual provides information on the features and installation of

the Punch AUDIO

phile

Systems. We suggest you save this manual

for future reference.

We strongly recommend you have your Authorized Rockford Fosgate

Dealer install the Punch AUDIO

phile

System. If you do choose to

install the system yourself, please be sure to read the entire manual

before beginning.

RFA-414 RFA-514

(1) Installation & Operation Manual (1) Installation & Operation Manual

(2) 4" Midrange Speakers (2) 5.25" Midrange Speakers

(2) 4" Speaker Grilles (2) 5.25" Speaker Grilles

(2) Speaker Grille Rings (2) Speaker Grille Rings

(2) Speaker Grille Gaskets (2) Speaker Grille Gaskets

(8 Tinnerman Clips (8) Tinnerman Clips

(2) RFA-142x Crossovers (2) RFA-142x Crossovers

(2) 20mm Tweeters (2) 20mm Tweeters

(2) Surface Mount Cups (2) Surface Mount Cups

(2) Surface Mount Baseplates (2) Surface Mount Baseplates

(2) Flush Mount Cups (2) Flush Mount Cups

(2) Flush Mount Baseplates (2) Flush Mount Baseplates

(2) Mounting Brackets (2) Mounting Brackets

(2) 6' 24 gauge speaker wire (2) 6' 24 gauge speaker wire

(16) #8 x .75 Phillips Mounting Screws (16) #8 x .75 Phillips Mounting Screws

(4) 8-32 x .50 Hex Head Bolts (4) 8-32 x .50 Hex Head Bolts

(4) 8-32 Nuts (4) 8-32 Nuts

(2) Surface Mount Baseplates

(2) Flush Mount Cups

(2) Flush Mount Baseplates

(2) Mounting Brackets

(2) 6' 24 gauge speaker wire

(16) #8 x .75 Phillips Mounting Screws

(4) 8-32 x .50 Hex Head Bolts

(4) 8-32 Nuts

(1) Installation & Operation Manual

(2) 6.5" Midrange Speakers

(2) 6.5" Speaker Grilles

(2) Speaker Grille Rings

(2) Speaker Grille Gaskets

(8 Tinnerman Clips

(2) RFA-142x Crossovers

(2) 20mm Tweeters

(2) Surface Mount Cups

RFA-614

PACKAGE CONTENTS

– 1 –

TECHNICAL DESIGN FEATURES

◆ Silk Dome

The silk dome used in the AUDIO

phile

tweeter allows linear move-

ment of the diaphragm and voice coil assembly. The linear movement

or “symmetrical control” of the assembly provides smooth and well

extended high frequency response.

THE RESULT: Smooth response for “audiophile” sound quality.

◆ Neodymium Magnets

The high ionic compound of neodymium enables a smaller tweeter

magnet assembly to be used as opposed to the much larger ferrite

magnets that are commonly used in speaker manufacturing.

THE RESULT: An efficient magnet which allows smaller tweeter

construction.

◆ Magnetic Fluid Cooling

Magnetic fluid is a synthetic liquid consisting of microscopic mag-

netic particles. The fluid has four times the thermal conductivity as air

which makes it an ideal cooling agent. Magnetic fluid is injected into

the voice coil gap which helps dissipate heat generated by the voice

coil.

THE RESULT: A thermal conductor which allows increased power

handling.

◆ Swivel Mount Design

The tweeter is encapsulated in a variable swivel housing. This design

allows direct dispersion of the tweeter in order to accommodate

various mounting positions. The swivel mount design allows the

tweeter to maximize its sonic potential.

THE RESULT: Precise tweeter imaging regardless of mounting position.

– 2 –

◆ Nitrile Rubber Surround

The nitrile material is resilient to temperature variations and provides

a consistent support necessary of the linear motion of the speaker

cone, In addition, the inherent damping capabilities eliminates the

transmission of sonic disturbances between the cone and the frame of

the speaker. This greatly improves the clarity of the speaker's midrange

frequency response.

THE RESULT: Improves speaker's frequency response.

◆ Flat Spider

The speaker's linear compliance is balanced through the use of a

“proprietary” flat spider design. A flat spider provides symmetrical

control of the voice coil through its cone excursion. Linear cone

excursion reduces harmonic distortion for improved sound quality.

THE RESULT: Reduces mechanical distortion for better sound quality

◆ High Temperature Voice Coil

The voice coil is of a high temperature copper wire construction. The

wire is wound in two layers on a black, anodized, aluminum voice

coil former. The voice coil former dissipates heat away from the voice

coil improving the speaker's thermal stability and improving the

reliability of the speaker.

THE RESULT: Improves reliability by dissipating generated heat.

◆ Vented Pole Piece

The vented pole piece by design, ensures proper ventilation to cool

the voice coil and maintain lower operating temperatures. The vent

on the rear of the magnet reduces back pressure and allows cool air

to circulate in the voice coil gap. The air circulation increases the

thermal power handling of the speaker.

THE RESULT: Improves power handling by cooling the voice coil.

Midrange Features

– 3 –

◆ Powder Coat Finish

Powder coating has long been the industry standard for durability in

protective metal finishes. A dry powder (non-aerosol) is electrostati-

cally applied to the metal and “baked” on to provide a hard “shell-

like” finish. As an additional benefit, powder coating is the only

finishing process that releases no toxic chemicals into our ozone.

THE RESULT: A durable and “earth friendly” metal finish.

Crossover Features

◆ Optical Compression Circuit

The speaker's linear compliance is balanced through the use of a

“proprietary” flat spider design. A flat spider provides symmetrical

control of the voice coil through its cone excursion. Linear cone

excursion reduces harmonic distortion for improved sound quality.

THE RESULT: Reduces mechanical distortion for better sound quality

◆ Series Notch Filter

The Series Notch Filter compensates for the inductive load presented

by the driver (speaker). The filter's primary function is to dampen and

eliminate the effect that driver resonance has on the crossover. The

Series Notch Filter flattens out the inductive load which greatly

improves driver performance by providing a “stable” crossover point.

THE RESULT: Improves driver performance by reducing resonant

peak.

– 4 –

◆ Zobel Network

The Zobel network compensate for the impedance rise presented by

the driver (speaker). The network flattens out the gradual impedance

rise produced by the voice coil which typically results in high

frequency rolloff. The Zobel Network compensates for this natural

rolloff which allows the driver to produce a more linear response up

to the tweeter crossover point.

THE RESULT: Compensates for natural high frequency rolloff of

midrange.

◆ Adjustable Tweeter Level Matching

The RFA-142x utilizes a series power resistor for tweeter level

matching. The factory set tweeter output level is –0dB, however, can

be reduced –3dB to create a smoother transition between the midrange

and tweeter. The ability to level match allows the system to be custom

“tuned” for a particular listener or setup.

THE RESULT: Allows custom setup of tweeter output level.

– 5 –

DESIGN FEATURES

1. Wire Mesh Grille – The Wire Mesh Grille protects the tweeter

diaphragm from foreign objects and curious fingers.

2. Input Terminals – The “+” Terminal indicates the positive/plus

terminal of the speaker. The “–” Terminal indicates the negative/

minus terminal of the speaker. These terminals connect to the

corresponding output of the supplied crossover.

3. Variable Mount Logo – The Diamond “R” logo can be orientated

in its housing to accommodate vertical or horizontal crossover

mounting.

4. Input Screw Terminals – The Input Screw Terminals connect to

the outputs of the amplifier. These terminals accept bare wire or

1/4" spade lugs and are gold-plated to resist corrosion.

5. Output Screw Terminals – The Output Screw Terminals connect

to the input of the tweeter and midrange. These terminals accept

bare wire or 1/4" spade lugs and are gold-plated to resist corro-

sion.

6. Surface Mount Cup – This cup is used to “surface mount” the

tweeter on a panel.

7. Flush Mount Cup – This cup is used to recess or “flush mount” the

tweeter into a panel.

®®

ACTIVE TWEETER PROTECTION

RFA-142x

– 6 –

INSTALLATION CONSIDERATIONS

Tools Needed

The following is a list of some of the tools necessary for the installation

of your speakers.

Power Drill with assorted bits #2 Phillips Screwdriver

Tape Measure Hole Saw (2")

Voltmeter

General

1. For safety, disconnect the negative lead from the battery prior to

beginning the installation.

2. Never run wires underneath the vehicle. Running the wires inside

the vehicle provides the best protection.

3. Avoid running wires over or through sharp edges. Use rubber of

plastic grommets to protect any wires routed through metal.

4. Mount the speakers/crossovers away from electrical sources (other

than the amplifier) i.e.., power cables, electronic fuel pumps,

vehicle computers, and other potential noise sources.

5. Mount the speakers/crossovers away from areas of extreme heat or

moisture.

Speakers

1. Make sure there is an area large enough of the speaker to mount.

Warning! Failure to do this can cause damage to the speaker if the

speaker frame is bent during installation.

2. Check to see that the location is deep enough for the speaker(s) and

the location does not interfere with the normal operation of the

vehicle.

3. When mounting the speaker(s) in the door of a vehicle, make sure

the speaker(s) do not interfere with either the door or window

operation.

4. When mounting the speaker(s) on the rear deck of the vehicle, check

the operation of the rear hatch or trunk lid. Make sure the torsion bars

and other moving parts are not obstructed by the speaker(s) instal-

lation.

• Please refer to the Specifications section of this manual for proper

mounting diameter and depth of the speaker(s).

Crossovers

1. Make sure there is a flat area large enough for the crossover to mount.

2. For best results, mount the crossover(s) next to the amplifier for a

decorative finish to the installation and provide an easy upgrade (no

new wires to run) for a bi-amp Rockford Fosgate system in the future.

– 7 –

MOUNTING LOCATION

A solid front stage with a good image is one of the most difficult tasks

to achieve in a vehicle. No car has the optimum listening environment.

This makes proper sound staging very difficult to accomplish. Most

speakers tend to be placed where they will fit easily, as opposed to

where they can perform the best.

The mounting location of your

speakers will have a great effect on the sound quality of your stereo

system. The special care taken to place the speakers will yield many

hours of listening enjoyment in return. Several important recommenda-

tions should be followed.

• Place the speakers where they have a

direct path to the listening area.

• For the best integration between the

midrange and tweeter, the tweeter should

be placed less than 2" from the midrange.

(Figure 1)

• If you cannot place the tweeter less than

2" from the midrange, then place the

tweeter more than 7" from the midrange.

Placing the tweeter 2"-7" from the

midrange can cause destructive inter-

ference (frequency response problems) which will affect the speaker's

ability to reproduce the frequency range around the crossover

frequency of the system.

• Whenever possible, place the tweeter directly above or below the

midrange as this maximizes the imaging (point source) capability of

the espeakrs. (Figure 2)

Figure 1

2" or less

Figure 2-A

Figure 2-B

– 8 –

• Sound radiated from a “point source” has the most optimum stereo

imaging because the separation of the acoustical centers between

the midrange and tweeter for each channel is at the optimum. Figure

2-A describes a horizontal speaker alignment. In a closed environ-

ment such as an automobile, horizontal speaker alignment can

cause severe amplitude and phase differences which will degrade

not only the imaging, but also the frequency response. This is due to

the path length differences between the midrange and tweeter.

Figure 2-B displays a vertical alignment between the midrange and

tweeter. With a vertical alignment, the path length difference

between the midrange and tweeter are reduced to a minimum. The

result is a negligible difference in path lengths between the midrange

and tweeter regardless of the proximity of the listener to the

speakers. Mounting the speaker with minimum path length differ-

ence will ensure the best staging an imaging possible from your

audio system.

INSTALLATION

Mounting the Midrange

– 9 –

® ®

1. Cut the proper size hole for the midrange/woofer.

• For the RFA-44, cut a 4" (101.6mm) diameter hole

• For the RFA-54, cut a 4

⁄16"

• For the RFA-64, cut a 5

⁄32"" (148.4mm) diameter hole

2. Place the mounting ring over the mounting hole and mark the

location of the screw mounting holes.

3. Remove the ring. Drill the holes for the screws using a 1/8" drill bit.

4. Route the wire through the hole.

5. Install the screw clips (Tinnerman clips) over the screw holes. Place

the mounting ring over the hole.

6. Attach the wires and be sure to observe the proper speaker polarity.

7. Place the speaker into the hole and screw the speaker into place.

Be careful not to bend the speaker frame during this step.

8. Press the speaker grille into the mounting ring.

– 10 –

Surface Mount Tweeter (Method #1)

• Use when mounting tweeter to a solid surface (metal, wood, etc.)

Mounting

Baffle

Mounting

Screw

Surface

Mount

Baseplate

Surface

Mount

Cup

Exploded View

Front View

(twist clockwise to lock)

Mounting

Baffle

Mounting

Bolt

Surface

Mount

Baseplate

Surface

Mount

Cup

Nut

Exploded View

Front View

(twist clockwise to lock)

• Use when mounting tweeter to a surface needing reinforcement

Surface Mount Tweeter (Method #2)

® ®

– 11 –

Crossover Connections

–

OUTPUT

FROM

AMPLIFIER

TWEETER

(Rear View)

“+”

Input

Tweeter

Output

“+”

HP CROSSOVER

TWEETER

PROTECTION

LP CROSSOVER

– +

Mid

Output

– + – +

Dot

• Striped Wire indicates “+”

terminal

of tweeter

• Be Sure to Maintain Speaker Polarity

Flush Mount Tweeter

Mounting

Baffle

Mounting

Bolt

Flush

Mount

Baseplate

Flush

Mount

Cup

Nut

2" Cutout

Bracket

Exploded View

Rear View

(twist clockwise to lock)

® ®

– 12 –

Bandpassing the Midrange

® ®

Midrange

Output

RFA-142x

400µf capacitor

–

• To bandpass the midrange, it is necessary to add a 400µf

capacitor in series with the speaker

Tweeter Level Matching

Cut jumper

wire for –3dB

• Factory set tweeter level is –0dB

• Cut jumper wire on bottom of crossover to reduce

tweeter level by –3dB

– 13 –

Horizontal Logo Mounting

Vertical Logo Mounting

®®

ACTIVE TWEETER PROTECTION

RFA-142x

®®

ACTIVE TWEETER PROTECTION

RFA-142x

• Configure logo into desired position and snap into place

®®

ACTIVE TWEETER PROTECTION

RFA-142x

®®

ACTIVE TWEETER PROTECTION

RFA-142x

® ®

TROUBLESHOOTING

No sound from

speakers

Symptom Diagnosis Remedy

Check and repair or replace

wiring as needed.

Check system with known

working amplifier and re-

pair or replace as needed.

Check for shorts in the wir-

ing with a volt/ohm meter

and repair or replace wires

as needed

Check system with known

working speaker and repair

or replace as needed.

Wires between amplifier,

crossover and speakers

not connected properly.

Amplifier has no output.

Speaker wires are shorted

to each other or to the

chassis of the vehicle.

Speakers are blown.

Incorrect wiring be-

tween crossover and

speakers

Excessive clipping from

amplifier

Equalizer in system (if

available) has excessive

boost in the high fre-

quency range

Check wiring and repair or

replace as needed.

Check gain settings on am-

plifier and readjust as neces-

sary

Check settings on equalizer

and readjust as necessary

Distorted sound

from speakers

Tweeters “burn

up” easily

– 14 –

Engi ne Noise

from One or

More Speakers

Symptom Diagnosis Remedy

Check for shorts in the wir-

ing with a volt/ohm meter

and repair or replace wires

as needed.

Re-route speaker wiring

away from noise sources.

(Refer to the Installation

Considerations section of

this manual.)

Move crossovers away from

noise sources. (Refer to the

Installation Considerations

section of this manual.)

Speaker wires shorted to

chassis of vehicle.

Speaker wires are routed

near radiated noise

source. (Power cables,

vehicle computers, etc.)

Crossover is mounted

near radiated noise

source. (Power cables,

vehicle computers, etc.)

– 15 –

TROUBLE-

SPECIFICATIONS

Model RFA-14 RFA-44 RFA-54 RFA-64

Freq. Response 3kHz-20kHz 3kHz-20kHz 44Hz-6kHz 39Hz-6kHz

Power Handling 50 Watts* 30 Watts 50 Watts 80 Watts

(RMS)

Nom. Impedance 4Ω 4Ω 4Ω 4Ω

Sensitivity 92dB 86dB 86dB 89dB

1W/1M)

Fs (Hz) 2000Hz 94Hz 44Hz 39Hz

Mounting Diameter Refer to 4" 4

⁄8"5

⁄8"

drawing (101.6mm) (122.8mm) (142.9mm)

Mounting Depth Refer to 1 2

⁄8"3

⁄32"

drawing (45.2mm) 66.7mm) (78.6mm)

*Power ratings (PE) is established with recommended filter network.

Model RFA-142x

Crossover Frequency 6kHz @ 4Ω

Crossover Slope 18dB/octave High-Pass

12dB/octave Low-Pass

Protection Circuitry Optical Compression

Crossover Alignment Butterworth

Zobel Network Effective @ 6.5kHz

Series Notch Filter Effective @ 2kHz

Tweeter Level Matching Factory set –0dB

User selectable –3dB

Flush MountSurface Mount

⁄16" (11.1mm)

⁄4" (19mm)

2" (54mm)

⁄8" (50.8mm)

⁄16"

(27mm)

⁄16"

(58.4cm)

(Specifications are subject to change without notice)

(End View)

⁄32"

(28.3mm)

– 16 –

®®

ACTIVE TWEETER PROTECTION

RFA-142x

– 17 –

LIMITED WARRANTY INFORMATION

Rockford Corporation offers a limited warranty on Rockford Fosgate products on the

following terms:

• Length of Warranty

1 year on speakers 30 days on speaker B-stock (receipt required)

3 years on electronics 90 days on electronic B-stock (receipt required)

2 years on source units

• What is Covered

This warranty applies only to Rockford Fosgate products sold to consumers by

Authorized Rockford Fosgate Dealers in the United States of America or its

possessions. Product purchased by consumers from an Authorized Rockford

Fosgate Dealer in another country are covered only by that country’s Distributor

and not by Rockford Corporation.

• Who is Covered

This warranty covers only the original purchaser of Rockford product purchased

from an Authorized Rockford Fosgate Dealer in the United States. In order to

receive service, the purchaser must provide Rockford with a copy of the receipt

stating the customer name, dealer name, product purchased and date of purchase.

• Products found to be defective during the warranty period will be repaired or

replaced (with a product deemed to be equivalent) at Rockford's discretion.

• What is Not Covered

1. Damage caused by accident, abuse, improper operations, water, theft

2. Any cost or expense related to the removal or reinstallation of product

3. Service performed by anyone other than Rockford or an Authorized Rockford

Fosgate Service Center

4. Any product which has had the serial number defaced, altered, or removed

5. Subsequent damage to other components

6. Any product purchased outside the U.S.

7. Any product not purchased from an Authorized Rockford Fosgate Dealer

• Limit on Implied Warranties

Any implied warranties including warranties of fitness for use and merchantability

are limited in duration to the period of the express warranty set forth above. Some

states do not allow limitations on the length of an implied warranty, so this

limitation may not apply. No person is authorized to assume for Rockford Fosgate

any other liability in connection with the sale of the product.

• How to Obtain Service

Please call 1-800-669-9899 for Rockford Customer Service. You must obtain an

RA# (Return Authorization number) to return any product to Rockford Fosgate. You

are responsible for shipment of product to Rockford.

Ship to: Electronics

Rockford Corporation

Warranty Repair Department

2055 E. 5th Street

Tempe, AZ 85281

RA#:_________________

Ship to: Speakers

Rockford Acoustic Design

(Receiving-speakers)

609 Myrtle N.W.

Grand Rapids, MI 49504

RA#:_________________

La page charge ...

Rockford Fosgate RFA-514 Manuel utilisateur

Marque: Rockford Fosgate

Modèle: RFA-514

Catégorie: Haut-parleurs de voiture

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Rockford Fosgate RFA-514 User manual

Rockford Fosgate RFA-514 Manuel utilisateur

Ce manuel convient également à

Rockford Fosgate RFA-514 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents