KitchenAid 12828154 Manuel utilisateur

Marque: KitchenAid

Modèle: 12828154

Catégorie: Frigos

Taper: Manuel utilisateur

Ce manuel convient également à

Refrigerator 12828154

BOTTOM-MOUNT REFRIGERATOR

Use & Care Guide

For questions about features, operation/performance, parts, accessories or service, call: 1-800-422-1230

or visit our website at www.kitchenaid.com

In Canada, call: 1-800-807-6777 or visit our website at www.KitchenAid.ca

RÉFRIGÉRATEUR SUPERPOSÉ

Guide d’utilisation et d’entretien

Au Canada, pour assistance, installation ou service composez le 1-800-807-6777 ou visitez notre site web à www.KitchenAid.ca

Table of Contents/Table des matières.............................................................................2

12828154

TABLE OF CONTENTS

REFRIGERATOR SAFETY .............................................................3

INSTALLATION INSTRUCTIONS..................................................4

Unpack the Refrigerator...............................................................4

Location Requirements................................................................4

Electrical Requirements ...............................................................5

Water Supply Requirements........................................................5

Connect the Water Supply...........................................................5

Base Grille ....................................................................................7

Refrigerator Doors........................................................................7

Freezer Drawer.............................................................................8

Adjust the Door ..........................................................................10

Water System Preparation.........................................................10

Normal Sounds ..........................................................................11

REFRIGERATOR USE..................................................................11

Opening and Closing Doors.......................................................11

Ensuring Proper Air Circulation..................................................11

Using the Controls .....................................................................11

Water Dispenser.........................................................................13

Water Filter Status Light.............................................................13

Water Filtration System..............................................................14

Ice Maker....................................................................................14

REFRIGERATOR FEATURES ......................................................14

Refrigerator Shelves...................................................................14

Crisper and Crisper Cover .........................................................15

Crisper Humidity Control............................................................15

Temperature-Controlled Drawer................................................15

Utility or Egg Bin.........................................................................16

FREEZER FEATURES ..................................................................16

Freezer Baskets..........................................................................16

DOOR FEATURES ........................................................................17

Door Retainer .............................................................................17

Door Bins....................................................................................17

Utility Compartment ...................................................................17

REFRIGERATOR CARE ...............................................................17

Cleaning......................................................................................17

Changing the Light Bulb.............................................................18

Power Interruptions....................................................................18

Vacation and Moving Care.........................................................18

TROUBLESHOOTING ..................................................................19

ASSISTANCE OR SERVICE.........................................................22

In the U.S.A. ...............................................................................22

In Canada ...................................................................................22

Accessories ................................................................................22

WATER FILTER CERTIFICATIONS.............................................22

PRODUCT DATA SHEETS...........................................................23

WARRANTY ..................................................................................24

TABLE DES MATIÈRES

SÉCURITÉ DU RÉFRIGÉRATEUR ..............................................25

INSTRUCTIONS D’INSTALLATION ...........................................26

Déballage du réfrigérateur .........................................................26

Exigences d'emplacement.........................................................26

Spécifications électriques..........................................................27

Spécifications de l’alimentation en eau.....................................27

Raccordement de la canalisation d'eau ....................................27

Grille de la base..........................................................................29

Portes du réfrigérateur ...............................................................29

Tiroir du congélateur ..................................................................30

Ajustement de la porte...............................................................32

Préparation du système d’eau...................................................32

Sons normaux ............................................................................33

UTILISATION DU RÉFRIGÉRATEUR..........................................33

Ouverture et fermeture des portes ............................................33

Pour s’assurer d’une circulation d’air appropriée .....................33

Utilisation des commandes........................................................34

Distributeur d’eau.......................................................................36

Témoin lumineux de l'état du filtre à eau...................................36

Système de filtration d’eau .......................................................36

Machine à glaçons .....................................................................37

CARACTÉRISTIQUES DU RÉFRIGÉRATEUR ...........................37

Tablettes du réfrigérateur...........................................................37

Bac à légumes et couvercle.......................................................38

Réglage de l’humidité dans le bac à légumes...........................38

Tiroir à température contrôlée....................................................38

Casier utilitaire ou oeufrier..........................................................39

CARACTÉRISTIQUES DU CONGÉLATEUR...............................39

Paniers de congélateur ..............................................................39

CARACTÉRISTIQUES DE LA PORTE.........................................40

Dispositif de retenue de la porte................................................40

Balconnets dans la porte ...........................................................40

Compartiment utilitaire...............................................................40

ENTRETIEN DU RÉFRIGÉRATEUR ............................................40

Nettoyage ...................................................................................40

Remplacement de l’ampoule d’éclairage ..................................41

Pannes de courant .....................................................................41

Entretien avant les vacances ou lors d’un déménagement.......42

DÉPANNAGE.................................................................................42

ASSISTANCE OU SERVICE.........................................................45

Accessoires ................................................................................45

FEUILLES DE DONNÉES SUR LE PRODUIT.............................46

GARANTIE.....................................................................................47

REFRIGERATOR SAFETY

Proper Disposal of Your Old Refrigerator

IMPORTANT: Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are still dangerous

– even if they will sit for “just a few days.” If you are getting rid of

your old refrigerator, please follow these instructions to help

prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

■ Take off the doors.

■ Leave the shelves in place so that children may not easily

climb inside.

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

IMPORTANT SAFETY INSTRUCTIONS

WARNING:

To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

SAVE THESE INSTRUCTIONS

■ Plug into a grounded 3 prong outlet.

■ Do not remove ground prong.

■ Do not use an adapter.

■ Do not use an extension cord.

■ Disconnect power before servicing.

■ Replace all parts and panels before operating.

■ Remove doors from your old refrigerator.

■ Use nonflammable cleaner.

■ Keep flammable materials and vapors, such as gasoline,

away from refrigerator.

■ Use two or more people to move and install refrigerator.

■ Disconnect power before installing ice maker (on ice maker

kit ready models only).

■ Use a sturdy glass when dispensing ice (on some models).

WARNING

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or brain damage.

INSTALLATION INSTRUCTIONS

Unpack the Refrigerator

Remove the Packaging

■ Remove tape and glue residue from surfaces before turning

on the refrigerator. Rub a small amount of liquid dish soap

over the adhesive with your fingers. Wipe with warm water

and dry.

■ Do not use sharp instruments, rubbing alcohol, flammable

fluids, or abrasive cleaners to remove tape or glue. These

products can damage the surface of your refrigerator. For

more information, see “Refrigerator Safety.”

■ Properly dispose of packaging.

Clean Before Using

After you remove all of the packaging materials, clean the inside

of your refrigerator before using it. See the cleaning instructions

in “Refrigerator Care.”

Location Requirements

■ Your refrigerator is designed for indoor, household use only.

■ To ensure proper ventilation for your refrigerator, allow for a

¹⁄₂" (1.25 cm) space at the top and behind the refrigerator.

■ If your refrigerator has an ice maker, allow extra space at the

back for the water line connections.

■ When installing your refrigerator next to a fixed wall, leave

2¹⁄₈" (5.4 cm) minimum on the hinge side (some models

require more) to allow for the door to swing open.

NOTE: It is recommended that you do not install the refrigerator

near an oven, radiator, or other heat source. Do not install the

refrigerator in a location where the temperature will fall below

55°F (13°C).

WARNING

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator

for cleaning or service, be sure to protect the floor.

Always pull the refrigerator straight out when moving it.

Do not wiggle or “walk” the refrigerator when trying to move

it, as floor damage could occur.

Important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

For your protection, tempered glass is designed to shatter

into many small, pebble-size pieces. This is normal. Glass

shelves and covers are heavy. Use special care when

removing them to avoid impact from dropping.

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

2¹⁄₈" (5.4 cm)

¹⁄₂" (1.25 cm)

Electrical Requirements

Before you move your refrigerator into its final location, it is

important to make sure you have the proper electrical

connection.

Recommended Grounding Method

A 115 Volt, 60 Hz., AC only 15- or 20-amp fused, grounded

electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet

that cannot be turned off by a switch. Do not use an

extension cord.

NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, turn the control (Thermostat, Refrigerator

or Freezer Control depending on the model) OFF and then

disconnect the refrigerator from the electrical source. When you

are finished, reconnect the refrigerator to the electrical source

and reset the control (Thermostat, Refrigerator or Freezer Control

depending on the model) to the desired setting.

Water Supply Requirements

Read all directions before you begin.

IMPORTANT:

■ If you turn the refrigerator on before the water line is

connected, turn the ice maker OFF.

■ All installations must meet local plumbing code requirements.

■ Use copper tubing and check for leaks. Install copper tubing

only in areas where the household temperatures will remain

above freezing.

TOOLS NEEDED: Gather the required tools and parts before

starting installation. Read and follow the instructions provided

with any tools listed here. Flat-blade screwdriver, ⁷⁄₁₆" and ¹⁄₂"

open-end wrenches or two adjustable wrenches, ¹⁄₄" nut driver

and drill bit, hand drill or electric drill (properly grounded).

NOTE: Your refrigerator dealer has a kit available with a ¹⁄₄"

(6.35 mm) saddle-type shutoff valve, a union, and copper tubing.

Before purchasing, make sure a saddle-type valve complies with

your local plumbing codes. Do not use a piercing-type or ³⁄₁₆"

(4.76 mm) saddle valve which reduces water flow and clogs more

easily.

Water Pressure

A cold water supply with water pressure of between 35 and

100 psi (241 and 689 kPa) is required to operate the water

dispenser and ice maker. If you have questions about your water

pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the

refrigerator needs to be between 35 and 100 psi

(241 and 689 kPa).

If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 to 414 kPa):

■ Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

■ Allow the storage tank on the reverse osmosis system to refill

after heavy usage.

■ If your refrigerator has a water filter, it may further reduce the

water pressure when used in conjunction with a reverse

osmosis system. Remove the water filter. See “Water

Filtration System.”

If you have questions about your water pressure, call a licensed,

qualified plumber.

Connect the Water Supply

Read all directions before you begin.

IMPORTANT: If you turn the refrigerator on before the water line

is connected, turn the ice maker OFF.

Connect to Water Line

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

3. Find a ¹⁄₂" to 1¹⁄₄" (12.7 mm to 3.18 mm) vertical cold water

pipe near the refrigerator.

IMPORTANT:

■ Make sure it is a cold water pipe.

■ Horizontal pipe will work, but the following procedure

must be followed: Drill on the top side of the pipe, not the

bottom. This will help keep water away from the drill. This

also keeps normal sediment from collecting in the valve.

4. Determine the length of copper tubing you need. Measure

from the connection on the lower right rear of refrigerator to

the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use ¹⁄₄"

(6.35 mm) O.D. (outside diameter) copper tubing. Be sure

both ends of copper tubing are cut square.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

5. Using a grounded drill, drill a ¹⁄₄" hole in the cold water pipe

you have selected.

6. Fasten the shutoff valve to the cold water pipe with the pipe

clamp. Be sure the outlet end is solidly in the ¹⁄₄" drilled hole

in the water pipe and that the washer is under the pipe clamp.

Tighten the packing nut. Tighten the pipe clamp screws

slowly and evenly so the washer makes a watertight seal. Do

not overtighten or you may crush the copper tubing.

7. Slip the compression sleeve and compression nut on the

copper tubing as shown. Insert the end of the tubing into the

outlet end squarely as far as it will go. Screw compression nut

onto outlet end with adjustable wrench. Do not overtighten.

8. Place the free end of the tubing in a container or sink, and

turn ON the main water supply. Flush the tubing until water is

clear. Turn OFF the shutoff valve on the water pipe.

Connect to Refrigerator

Depending on your model, the water line may come down from

the top or up from the bottom. Follow the connection instructions

for your model.

Style 1

1. Remove plastic cap from water valve inlet port. Attach the

copper tube to the valve inlet using a compression nut and

sleeve as shown. Tighten the compression nut. Do not

overtighten. Confirm copper tubing is secure by pulling on

copper tubing.

2. Create a service loop with the copper tubing. Avoid kinks

when coiling the copper tubing. Secure copper tubing to

refrigerator cabinet with a “P” clamp.

3. Turn on water supply to refrigerator and check for leaks.

Correct any leaks.

Style 2

1. Create a service loop (minimum diameter of 2 ft [61 cm]) with

the copper tubing. Avoid kinks when coiling the copper

tubing.

2. Remove the plastic cap from water valve inlet port. Place a

compression nut and sleeve on the copper tubing.

3. Insert the end of the copper tubing into the water valve inlet

port. Shape tubing slightly so that the tubing feeds straight

into the port to avoid kinks.

4. Slide the compression nut over the sleeve and screw into the

water valve inlet port.

A. Cold water pipe

B. Pipe clamp

C. Copper tubing

D. Compression nut

E. Compression sleeve

F. Shutoff valve

G. Packing nut

A. Copper tubing

B. “P” clamp

C. Compression nut

D. Compression sleeve

E. Water valve inlet port

A. Plastic water tubing

B. Sleeve

C. Compression nut

D. Copper tubing

5. Using an adjustable wrench, hold the nut on the plastic water

line to keep it from moving. Then, with a second wrench turn

the compression nut on the copper tubing counterclockwise

to completely tighten. Do not overtighten.

6. Check connection by pulling on copper tubing. Attach copper

tubing to refrigerator cabinet with a “P” clamp. Turn on water

supply to refrigerator and check for leaks. Correct any leaks.

Complete the Installation

1. Plug into a grounded 3 prong outlet.

NOTE: Allow 24 hours to produce the first batch of ice. Discard

the first three batches of ice produced. Allow 3 days to

completely fill the ice container.

Base Grille

Remove the Base Grille

1. Grasp the grille with both hands.

2. Pull the grille toward you.

Replace the Base Grille

1. See the markings on the inside of the base grille for proper

placement.

2. Align the grille mounting clips with the cabinet slots.

3. Push the grille firmly into the cabinet slots until it snaps into

place.

Refrigerator Doors

Graphics are included later in this section.

Remove and Replace Handles

1. Using a ³⁄₃₂" Allen wrench, loosen the two set screws located

on the side of each handle. See Graphics 1 and 2.

2. Pull the handle straight out from the door. Make sure you

keep the screws for reattaching the handles.

3. To replace the handles, reverse the directions.

Remove Doors and Hinges

IMPORTANT:

■ Remove food and any adjustable door or utility bins from

doors.

■ All graphics referenced in the following instructions are

included later in this section after “Final Steps.”

TOOLS NEEDED: ⁵⁄₁₆", ³⁄₈", ¹⁄₄" hex-head socket wrench,

#2 Phillips screwdriver, and a flat-blade screwdriver.

A. Plastic water line

B. Water valve inlet port

C. Compression nut

D. Copper tubing

E. “P” clamp

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

1. Unplug refrigerator or disconnect power.

2. Keep the refrigerator doors closed until you are ready to lift

them free from the cabinet.

NOTE: Provide additional support for the refrigerator door

while the hinges are being removed. Do not depend on the

door gasket magnets to hold the door in place while you are

working.

3. Starting with the right-hand side door, remove the parts for

the top hinge as shown in Top Hinge graphic. Lift the

refrigerator door from the bottom hinge pin.

4. Remove the shim from the bottom hinge pin and keep it for

later use. See Bottom Hinge graphic.

5. Before removing the left-hand side door, disconnect the wire

harness located on top of the top hinge by wedging a flat-

blade screwdriver or your fingernail between the two

sections. See Wire Harness graphic.

NOTE: The green, ground wire remains attached to the hinge.

6. Remove the parts for the top hinge as shown in Top Hinge

graphic. Lift the left-hand side door from the bottom hinge

pin.

7. Remove the shim from the bottom hinge pin and keep it for

later use. See Bottom Hinge graphic.

Replace Doors and Hinges

1. Assemble the parts for the top hinge as shown in Top Hinge

graphic. Do not tighten the screws completely.

2. Replace the parts for the bottom hinge as shown in Bottom

Hinge graphic. Tighten screws. Replace the refrigerator door.

NOTE: Provide additional support for the refrigerator door

while the hinges are being moved. Do not depend on the door

gasket magnets to hold the door in place while you are

working.

3. Align the door so that the bottom of the refrigerator door

aligns evenly with the top of the freezer drawer. Tighten all

screws.

4. Reconnect the wire harness on top of the left-hand side

refrigerator door.

5. Replace the top hinge covers.

Freezer Drawer

Graphics are included later in this section.

Remove Drawer

IMPORTANT: Two people may be required to complete this

procedure.

1. Open the freezer drawer to full extension.

2. Remove all articles from baskets.

3. Pull the upper wire basket out to full extension and lift out to

remove.

4. Lift lower basket straight up and out to remove.

5. Remove the basket cradles from the drawer rails. Push the

snap attachments inward away from the drawer rails to

unlatch the basket cradles. Lift the basket cradles off the

drawer rails.

6. Lift the top of the freezer drawer front to unhook supports

from drawer rails. Lift drawer out.

Replace Drawer

IMPORTANT: Two people may be required to complete this

procedure.

1. Pull both drawer rails out to full extension.

2. Locate the notches on the inside of each drawer rail. See

Graphic 3-1.

3. While supporting the drawer front, hook the drawer supports

into the notches on the inside of the drawer rails. Lower the

drawer front into its final position. See Graphic 3-2.

4. Place the basket cradles back on the drawer rails. Align the

snap attachments with the slots on the drawer rails, and

press each snap toward the rail until it clicks.

5. With drawer rails pulled out to full extension, set the lower

basket straight down into the basket cradles.

6. Slide the upper basket into the molded drawer rail. Make sure

the rear of the basket hooks behind the drawer rail stop.

Final Steps

1. Plug in refrigerator to a grounded 3 prong outlet.

2. Return all removable door parts to doors and food to

refrigerator.

A. Cradle snap attachment

B. Basket cradle

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

3-2

Drawer Removal & Replacement

3-1

Door Removal & Replacement

Top Hinges

A. Hinge Cover Screw

B. Top Hinge Cover

" Hex-Head Hinge Screws

D. Top Hinge

A. Shim

C. Hinge Screws

B. Bottom Hinge

Bottom Hinges

Wire Harness

" Set Screw

Adjust the Door

Depending on your model, your refrigerator may have two

(Style 1) or four (Style 2) adjustable rollers located at the base of

the refrigerator. If your refrigerator seems unsteady or you want

the door to close easier, adjust the refrigerator's tilt using the

instructions below.

1. Remove the base grille. Grasp the grille firmly and pull it

toward you.

2. Using a screwdriver or ³⁄₈" hex driver, turn the roller

adjustment screw(s) on each side to raise or lower that side of

the refrigerator.

NOTE: Having someone push against the top of the

refrigerator takes some weight off the adjustment screws and

rollers. This makes it easier to turn the screws.

■ To raise, turn the roller adjustment screw to the right.

■ To lower, turn the roller adjustment screw to the left.

NOTE: It may take several turns of the roller adjustment

screw to adjust the tilt of the refrigerator.

Style 1 - Front leveling

Style 2 - Front and rear leveling

3. Open the door again to make sure that it closes as easily as

you like. If not, tilt the refrigerator slightly more to the rear by

turning both front adjustment screws to the right. It may take

several more turns, and you should turn both adjustment

screws the same amount.

4. Lower the stabilizing foot by turning it clockwise until it is

firmly against floor.

5. Turn the front adjustment screws counterclockwise to allow

the full weight of the refrigerator to rest on the stabilizing feet.

6. Replace the base grille.

Water System Preparation

Please read before using the water system.

Immediately after installation, follow the steps below to make

sure that the water system is properly flushed.

1. Turn off the ice maker by opening the freezer door and lifting

up the wire shutoff arm as shown.

2. Install the interior water filter. The interior water filter mounting

bracket is located on the left side wall of the refrigerator

compartment.

■ Remove blue bypass cap and retain for later use.

■ Remove the interior water filter from its packaging.

Remove the sealing label from the end of the filter and

insert it into the filter head.

■ Gently rotate the filter clockwise until it stops. Then snap

the filter cover closed.

3. Flush the water system by dispensing and discarding 2 to

3 gal. (8 to 12 L) of water. Flushing the system will take

approximately 6 to 7 minutes and will help clear air from the

line. Additional flushing may be required in some households.

NOTE: As air is cleared from the system, water may spurt out

of the dispenser.

4. Inspect the filter system for water leaks. If you see water

leaks, see the “Troubleshooting” section.

5. Turn on the ice maker by opening the freezer door and

lowering the wire shutoff arm as shown.

Please refer to the

“Ice Maker” section for further instructions on the operation

of your ice maker.

■ Allow 24 hours to produce the first batch of ice.

■ Discard the first three batches of ice produced.

A. Roller adjustment screw

B. Stabilizing foot

A. Front adjustment screw

B. Rear adjustment screw

C. Stabilizing foot

A B AB

Do not use with water that is microbiologically unsafe or

of unknown quality without adequate disinfection before

or after the system. Systems certified for cyst reduction

may be used on disinfected waters that may contain

filterable cysts.

Normal Sounds

Your new refrigerator may make sounds that your old one didn’t

make. Because the sounds are new to you, you might be

concerned about them. Most of the new sounds are normal. Hard

surfaces, such as the floor, walls, and cabinets, can make the

sounds seem louder. The following describes the kinds of sounds

and what may be making them.

■ If your refrigerator is equipped with an ice maker, you will hear

a buzzing sound when the water valve opens to fill the ice

maker for each cycle.

■ Your refrigerator is designed to run more efficiently to keep

your food items at the desired temperatures and to minimize

energy usage. The high efficiency compressor and fans may

cause your refrigerator to run longer than your old one. You

may also hear a pulsating or high-pitched sound from the

compressor or fans adjusting to optimize performance.

■ You may hear the evaporator fan motor circulating air through

the refrigerator and freezer compartments. The fan speed

may increase as you open the doors or add warm food.

■ Rattling noises may come from the flow of refrigerant, the

water line, or items stored on top of the refrigerator.

■ Water dripping on the defrost heater during a defrost cycle

may cause a sizzling sound.

■ As each cycle ends, you may hear a gurgling sound due to

the refrigerant flowing in your refrigerator.

■ Contraction and expansion of the inside walls may cause a

popping noise.

■ You may hear air being forced over the condenser by the

condenser fan.

■ You may hear water running into the drain pan during the

defrost cycle.

REFRIGERATOR USE

Opening and Closing Doors

(on some models)

There are two refrigerator compartment doors. The doors can be

opened and closed either separately or together.

There is a vertically-hinged seal on the left refrigerator door.

■ When the left side door is opened, the hinged seal

automatically folds inward so that it is out of the way.

■ When both doors are closed, the hinged seal automatically

forms a seal between the two doors.

Ensuring Proper Air Circulation

In order to ensure proper temperatures, you need to permit

airflow between the refrigerator and freezer sections. As shown in

the illustration, cool air enters the freezer section through vents in

the rear and top. The air flows forward through the freezer section

and recirculates under the freezer floor. Cool air enters the

refrigerator section through the top, flows down and across

shelves to the doors and recirculates to return air vents at the

bottom.

Do not block any airflow vents. If the vents are blocked, airflow

will be obstructed and temperature and moisture problems may

occur.

IMPORTANT: Because air circulates between both sections, any

odors formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To avoid odor

transfer and drying out of food, wrap or cover foods tightly.

Using the Controls

The control center is located at the top front of the refrigerator

compartment.

Temperature Controls

For your convenience, your temperature controls are preset at

the factory. When you first install your refrigerator, make sure the

controls are still set to the recommended set points as shown.

Recommended Settings

IMPORTANT:

■ When the power is on, the temperature display shows the

actual temperature of the compartment.

■ Wait 24 hours for your refrigerator to cool completely before

adding food. If you add food before the refrigerator has

cooled completely, your food may spoil.

NOTE: Adjusting the refrigerator and freezer temperature

controls to a colder than recommended setting will not cool

the compartments any faster.

■ The recommended settings should be correct for normal

household refrigerator use. The controls are set correctly

when milk or juice is as cold as you like and when ice cream

is firm.

A. Hinged seal

■ If the temperature is too warm or too cold in the refrigerator or

freezer, first check the air vents to be sure they are not

blocked before adjusting the controls. See “Ensuring Proper

Air Circulation.”

To Turn Your Refrigerator Off/On:

■ Press the freezer (+) touch pad repeatedly until “OFF”

appears in the freezer display. Allow a few seconds for the

refrigerator to shut off. Neither compartment will cool.

■ Press either the refrigerator or freezer (-) touch pad to turn on

the refrigerator.

Adjusting Controls

The REFRIGERATOR control adjusts the refrigerator

compartment temperature. The FREEZER control adjusts the

freezer compartment temperature.

If you need to adjust the temperature in either the refrigerator or

freezer compartment, use the settings listed in the chart as a

guide.

To Adjust Set Point Temperatures:

The first touch of the (+) or (-) touch pad displays the current

temperature set point. The display will show the set point for

approximately 3 seconds, and then return to the actual

temperature.

■ Press the (+) or (-) touch pads until the desired temperature

set point is displayed.

NOTE: Except when first turning on the refrigerator, do not

adjust either temperature control more than one setting at a

time. Wait 24 hours for the temperature to stabilize between

adjustments.

Additional Control Center Features

Max Cool

The max cool feature assists with periods of high refrigerator use,

full grocery loads, or temporarily warm room temperatures.

■ Press the Max Cool touch pad to set the freezer and

refrigerator to the lowest temperature settings. Press the Max

Cool touch pad again to return to the normal refrigerator set

point.

NOTE: The Max Cool feature will automatically shut off in

approximately 12 hours.

OptimIce

Feature

The OptimIce

feature assists with temporary periods of heavy

ice use by increasing ice production.

■ Press the OptimIce

feature touch pad to set the freezer to

the lowest temperature setting. Press the OptimIce

feature

touch pad again to return to the normal freezer set point.

NOTE: The OptimIce

feature will automatically shut off in

approximately 24 hours.

Holiday Mode

In Holiday Mode, the freezer will not automatically defrost as

often to conserve energy.

■ Press the Holiday Mode touch pad until the indicator light is

lit to turn on this feature. Press the Holiday Mode touch pad

again or open the refrigerator door to turn off this feature.

NOTE: The refrigerator door may be opened within 1 hour of

setting Holiday Mode without turning off the feature.

Temp Alarm

The Temp Alarm feature provides temperature information in the

event of a power outage.

Power Outage: During a power outage, if the temperatures in the

refrigerator and freezer compartments exceed normal operating

temperatures, the highest temperature reached will be displayed.

■ Press the Temp Alarm touch pad until the indicator light is lit,

to turn on this feature. Press and hold Temp Alarm for

3 seconds until the indicator light goes off to turn off this

feature.

CONDITION/REASON: ADJUSTMENT:

REFRIGERATOR too warm

- Door opened often, large amount

of food added or room

temperature very warm

Adjust REFRIGERATOR

TEMPERATURE Control

1° lower

FREEZER too warm/ice not made

fast enough

- Door opened often, or large

amount of food added or very cold

room temperature (can’t cycle

often enough)

- Heavy ice usage

Adjust FREEZER

TEMPERATURE Control

1° lower

REFRIGERATOR too cold

- Controls not set correctly for

your conditions

Adjust REFRIGERATOR

TEMPERATURE Control

1° higher

FREEZER too cold

- Controls not set correctly for

your conditions

Adjust FREEZER

TEMPERATURE Control

1° higher

Temperature Alarm: An alarm will sound repeatedly if the freezer

or refrigerator compartment temperatures exceed normal

operating temperatures for an hour or more.

The temperature displays will alternately show the current

temperatures and the highest temperatures the compartments

reached.

■ Press the Temp Alarm touch pad once to stop the audible

alarm and alternating temperature displays. The Temp Alarm

light will continue to flash until the refrigerator returns to the

set temperature.

Door Alarm

The Door Alarm feature sounds a chime every few seconds when

the refrigerator door has been left open for 5 continuous minutes.

The chime will sound until the door is closed or Door Alarm is

turned off.

■ Press the Door Alarm touch pad to turn this feature on or off.

The indicator light will be lit when the Door Alarm feature is

on.

Water Filter Status Light and Filter Reset

(on some models)

See “Water Filter Status Light.”

User Preferences

The control center allows you to set user preferences, if desired.

Temperature Display (F_C)

This preference allows you to change the temperature display.

F - Temperature in degrees Fahrenheit

C - Temperature in degrees Celsius

Alarm (AL)

This preference allows you to turn off the sound of all alarms.

ON - You will hear the alarm sound.

OFF - You will not hear the alarm sound.

Sabbath Mode (SAB)

IMPORTANT: This preference does not disable interior lights.

ON - All control panel lights will be disabled.

OFF - All control panel lights will be enabled.

NOTE: Press any touch pad on the control panel to restore the

control panel lights.

To Access the User Preferences Menu:

1. Press and hold the Door Alarm touch pad for 3 seconds. The

preference name will appear in the Freezer display and the

preference status (F or C) or (ON or OFF) will appear in the

Refrigerator display.

2. Use the Freezer (+) or (-) touch pads to scroll through the

preference names. When the desired preference name is

displayed, press the Refrigerator (+) or (-) touch pads to

change the preference status.

3. Set your preferences by pressing and holding the Door Alarm

touch pad for 3 seconds, or by shutting the refrigerator

compartment door.

Water Dispenser

(on some models)

If you did not flush the water system when the refrigerator was

first installed, dispense water into a container until you draw and

discard 2 to 3 gal. (8 to 12 L) or for approximately 6 to 7 minutes

after the water begins dispensing. The water you draw and

discard rinses the pipes. Allow several hours for the refrigerator

to cool down and chill water.

Dispensing Water

1. Hold a container under the dispenser while pressing the

button.

2. Release the button to stop dispensing.

NOTE: Dispense enough water every week to maintain a fresh

supply.

Water Filter Status Light

(on some models)

The water filter status light will help you know when to change

the water filter. When the yellow (Order) light is on, it is almost

time to change the water filter. When the red (Replace) light is on,

a new water filter should be installed. See “Water Filtration

System.”

After replacing the water filter, press and hold FILTER RESET for

3 seconds until the Order or Replace light turns off.

Water Filtration System

IMPORTANT:

■ The water filter should be replaced when the status light is

red (Replace) or earlier if the flow of water to your water

dispenser or ice maker decreases noticeably.

■ Air trapped in the system may cause water and the water

filter to eject. Dispense water for 2 minutes before removing

the used water filter.

Replacing the Water Filter

The water filter mounting bracket is located on the right side of

the refrigerator compartment.

1. Turn the used water filter counterclockwise until it releases

from the filter mounting bracket.

2. Drain water from the water filter into the sink, and discard the

used water filter. Wipe up the excess water in the filter cover.

3. Remove the sealing label from the end of the new water filter

and insert the water filter into the filter mounting bracket.

Gently rotate the water filter clockwise until it stops, and snap

the filter cover closed.

4. Flush the water system by dispensing and discarding 2 to

3 gal. (8 to 12 L) of water. Cleaning the system will take

approximately 6 to 7 minutes and will help clear air from the

line. Additional flushing may be required in some households.

5. Inspect the water filter system for leaks. If you see water

leaks, see “Troubleshooting.”

Using the Dispenser Without a Water Filter

You can use the water dispenser without a water filter, but your

water will not be filtered. If you choose this option, replace the

water filter with the blue bypass cap.

Ice Maker

Turning the Ice Maker On/Off

NOTE: Do not force the wire shutoff arm up or down.

■ To turn the ice maker on, simply lower the wire shutoff arm.

NOTE: Your ice maker has an automatic shutoff. As ice is

made, the ice cubes will fill the ice storage bin and the ice

cubes will raise the wire shutoff arm to the OFF (arm up)

position.

■ To manually turn the ice maker off, lift the wire shutoff arm to

the OFF (arm up) position and listen for the click to make sure

the ice maker will not continue to operate.

Ice Production Rate

■ Normal Ice Production: The ice maker should produce a

complete batch of ice every 3 hours. If ice is not being made

fast enough, adjust the Freezer Control to a lower (colder)

number in steps. Wait 24 hours. If necessary, gradually adjust

the Freezer Control to the lowest setting, waiting 24 hours

between each adjustment.

■ OptimIce Production (on some models): The ice maker

should produce approximately 16 to 20 batches of ice in a

24-hour period. If your refrigerator has the OptimIce

production feature, press the OptimIce touchpad.

Remember

■ Allow 24 hours to produce the first batch of ice. Discard the

first three batches of ice produced.

■ The quality of your ice will be only as good as the quality of

the water supplied to your ice maker. Avoid connecting the

ice maker to a softened water supply. Water softener

chemicals (such as salt) can damage parts of the ice maker

and lead to poor quality ice. If a softened water supply cannot

be avoided, make sure the water softener is operating

properly and is well maintained.

■ Do not store anything on top of the ice maker or in the ice

storage bin.

REFRIGERATOR FEATURES

Your model may have some or all of these features.

Refrigerator Shelves

The shelves in your refrigerator are adjustable to meet your

individual storage needs.

Storing similar food items together in your refrigerator and

adjusting the shelves to fit different heights of items will make

finding the exact item you want easier. It will also reduce the

amount of time the refrigerator door is open, and save energy.

Do not use with water that is microbiologically unsafe or

of unknown quality without adequate disinfection before

or after the system. Systems certified for cyst reduction

may be used on disinfected waters that may contain

filterable cysts.

Important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

For your protection, tempered glass is designed to shatter

into many small, pebble-size pieces. This is normal. Glass

shelves and covers are heavy. Use special care when

removing them to avoid impact from dropping.

Slide-out Shelves

■ To slide out shelf, gently pull front of shelf toward you.

■ To slide in shelf, push shelf in until it stops.

Shelves and Shelf Frames

To Remove and Replace a Shelf/Shelf Frame:

1. Remove the shelf/frame by tilting it up at the front and lifting it

out of the shelf supports.

2. Replace the shelf/frame by guiding the rear shelf hooks into

the shelf supports. Tilt the front of the shelf up until rear shelf

hooks drop into the shelf supports.

3. Lower the front of the shelf and check to make sure that the

shelf is securely in position.

Crisper and Crisper Cover

To Remove and Replace the Crisper(s):

1. Slide crisper(s) straight out to the stop. Lift the front of the

crisper(s) and slide out the rest of the way.

2. Replace the crisper(s) by sliding back in fully past the drawer

stop.

To Remove the Crisper(s) Cover:

1. Remove crisper(s).

2. Holding the glass insert firmly with one hand, press up in

center of glass insert until it rises above the plastic frame.

Gently, slide the glass insert forward to remove.

3. Lift the cover frame up and remove it.

To Replace Crisper(s) Cover:

NOTE: Before reinstalling the cover, make sure the

U-shaped reinforcement bar is reinstalled in the front edge of the

crisper cover.

1. Fit back of cover frame into supports on side walls of the

refrigerator and lower the front of the cover frame into place.

2. Slide rear of glass insert into cover frame and lower front into

place.

Crisper Humidity Control

You can control the amount of humidity in the moisture-sealed

crisper. Adjust the control to any setting between LOW and

HIGH.

LOW (open) lets moist air out of the crisper for best storage of

fruits and vegetables with skins.

■ Fruit: Wash, let dry and store in refrigerator in plastic bag or

crisper. Do not wash or hull berries until they are ready to use.

Sort and keep berries in original container in crisper, or store

in a loosely closed paper bag on a refrigerator shelf.

■ Vegetables with skins: Place in plastic bags or plastic

container and store in crisper.

HIGH (closed) keeps moist air in the crisper for best storage of

fresh, leafy vegetables.

■ Leafy vegetables: Wash in cold water, drain and trim or tear

off bruised and discolored areas. Place in plastic bag or

plastic container and store in crisper.

Temperature-Controlled Drawer

The full-width, temperature-controlled drawer can be used to

store large party trays, deli items, or beverages. For storage

flexibility the drawer features a divider and an adjustable

temperature control.

NOTE: Do not place leafy vegetables in the temperature-

controlled drawer. Colder temperatures could damage leafy

produce.

Drawer Removal and Replacement

Depending on your model, your refrigerator may have one of two

drawer styles. Follow the instructions for the appropriate drawer

style.

Style 1 - Flat-lid Drawer

To remove the drawer:

1. Pull the drawer out to its full extension.

2. Tilt up the front of the drawer and pull it straight out.

To replace the drawer:

1. Push the metal glide rails to the rear of the refrigerator.

2. Place the drawer onto the glide rails and slide the drawer

toward the rear of the refrigerator.

LOW

HIGH

Style 2 - Lift-up-lid Drawer

To remove the drawer:

1. Lift the lid. Pull the drawer out to its full extension.

2. Tilt up the front of the drawer and pull it straight out.

To replace the drawer:

1. Push the metal glide rails to the rear of the refrigerator.

2. Place the drawer onto the glide rails and slide the drawer

toward the rear of the refrigerator.

Drawer Divider

To Remove the Divider:

1. Pull the drawer out to its full extension.

2. Lift the front of the divider to unhook it from the rear wall of

the drawer and lift the divider out.

To Replace the Divider:

1. Hook the back of the divider over the rear wall of the drawer.

2. Lower the divider into place.

Drawer Temperature Control

The temperature control, located under the lid on the right-hand

side of the drawer, regulates the amount of cold air coming into

the drawer.

NOTE: Cold air directed into the drawer can decrease the

refrigerator temperature. The refrigerator temperature may need

to be adjusted.

■ Slide the temperature control to the least cold setting if you

want the drawer to be the same temperature as the

refrigerator compartment.

■ Slide the temperature control to a colder setting when you

want the drawer to be colder than the refrigerator

compartment.

NOTE: Use the coldest setting when storing meats.

Meat Storage Guide

Store most meat in original wrapping as long as it is airtight and

moisture-proof. Rewrap if necessary. See the following chart for

storage times. When storing meat longer than the times given,

freeze the meat.

Fresh fish or shellfish ................. use same day as purchased

Chicken, ground beef, variety meats (liver)............... 1-2 days

Cold cuts, steaks/roasts ........................................... 3-5 days

Cured meats ........................................................... 7-10 days

Leftovers - Cover leftovers with plastic wrap, aluminum foil, or

plastic containers with tight lids.

Utility or Egg Bin

Depending on your model, you may have a one, two or three

piece bin. Eggs may be stored in the egg tray or loose in the bin.

NOTE: Store eggs in a covered container for long-term storage. If

your model does not have an egg storage bin, store eggs in their

original carton on an interior shelf.

FREEZER FEATURES

Your model may have some or all of these features.

Freezer Baskets

To Remove and Replace Wire Baskets:

Upper basket

1. Remove all items from basket. Remove basket by pulling

basket out to its full extension and lift out.

2. Replace basket by sliding into upper molded railing. Make

sure that rear of basket hooks behind rail catch.

Upper basket divider

■ The upper basket divider separates ice making from frozen

food storage and it helps keep ice from falling behind the

basket assemblies.

■ The upper basket divider is designed to be non-removable

and should remain in the basket.

Lower basket

1. Remove all items from basket. Remove the basket by lifting it

from the rail guides.

2. Replace the basket by placing into rail guides.

Lower basket divider

The lower basket divider is designed to be non-removable and it

should remain in the basket.

A. Divider

DOOR FEATURES

Your model may have some or all of these features.

Door Retainer

(on some models)

To Remove and Replace the Door Retainer:

1. Remove the retainer by lifting it up and pulling it straight out.

2. Replace the retainer by sliding it in above the support and

pushing it down until it stops.

Door Bins

To Remove and Replace the Bins:

1. Remove the bin by lifting it up and pulling it straight out.

2. Replace the bin by sliding it in above the desired support and

pushing it down until it stops.

Utility Compartment

To Remove and Replace the Utility Compartment:

1. Remove the utility compartment by lifting it up and pulling it

straight out.

2. Replace the utility compartment by sliding it in above the

desired support and pushing it down until it stops.

REFRIGERATOR CARE

Cleaning

Both the refrigerator and freezer sections defrost automatically.

However, clean both compartments about once a month to avoid

build-up of odors. Wipe up spills immediately.

To Clean Your Refrigerator:

1. Unplug refrigerator or disconnect power.

2. Remove all removable parts from inside, such as shelves,

crispers, etc.

3. Hand wash, rinse, and dry removable parts and interior

surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

■ Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, cleaning

waxes, concentrated detergents, bleaches or cleansers

containing petroleum products on plastic parts, interior

and door liners or gaskets. Do not use paper towels,

scouring pads, or other harsh cleaning tools. These can

scratch or damage materials.

■ To help remove odors, you can wash interior walls with a

mixture of warm water and baking soda (2 tbs to 1 qt

[26 g to 0.95 L] of water).

4. Determine whether your refrigerator exterior is painted metal,

brushed aluminum or stainless steel and choose the

appropriate cleaning method.

Painted metal: Wash exteriors with a clean sponge or soft

cloth and a mild detergent in warm water. Do not use abrasive

or harsh cleaners, or cleaners designed for stainless steel.

Dry thoroughly with a soft cloth. For additional protection

against damage to painted metal exteriors, apply appliance

wax (or auto paste wax) with a clean, soft cloth. Do not wax

plastic parts.

Brushed aluminum: Wash with a clean sponge or soft cloth

and a mild detergent in warm water. Do not use abrasive or

harsh cleaners, or cleaners designed for stainless steel. Dry

thoroughly with a soft cloth.

WARNING

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

Stainless steel finish: Wash with a clean sponge or soft

cloth and a mild detergent in warm water. Do not use abrasive

or harsh cleaners. Dry thoroughly with a soft cloth.

■ To keep your stainless steel refrigerator looking like new

and to remove minor scuffs or marks, it is suggested that

you use the manufacturer’s approved Stainless Steel

Cleaner & Polish. To order the cleaner, see the

“Accessories” section.

IMPORTANT: This cleaner is for stainless steel parts only!

Do not allow the Stainless Steel Cleaner & Polish to come into

contact with any plastic parts such as the trim pieces,

dispenser covers or door gaskets. If unintentional contact

does occur, clean plastic part with a sponge and mild

detergent in warm water. Dry thoroughly with a soft cloth.

5. There is no need for routine condenser cleaning in normal

home operating environments. If the environment is

particularly greasy or dusty, or there is significant pet traffic in

the home, the condenser should be cleaned every 2 to

3 months to ensure maximum efficiency.

If you need to clean the condenser:

■ Remove the base grille. See “Base Grille” graphic or

“Base Grille” section.

■ Use a vacuum cleaner with a soft brush to clean the grille,

the open areas behind the grille and the front surface area

of the condenser.

■ Replace the base grille when finished.

6. Plug in refrigerator or reconnect power.

Changing the Light Bulb

NOTE: Not all appliance bulbs will fit your refrigerator. Be sure to

replace the bulb with one of the same size, shape, and wattage.

Changing the Refrigerator Light Bulb

1. Unplug the refrigerator or disconnect power.

2. Slide the light bulb cover toward the back of the

compartment to release it from the light assembly.

3. Replace burned-out bulb(s) with appliance light bulb(s) no

greater than 40 watts.

4. Replace the light bulb cover by inserting the tabs on the

cover into the liner holes on each side of light assembly. Slide

the cover toward the front until it locks into place.

NOTE: To avoid damaging the light cover, do not force the

cover beyond the locking point.

5. Plug in refrigerator or reconnect power.

Changing the Freezer Light Bulb

1. Unplug refrigerator or disconnect power.

NOTE: You may need to remove the upper freezer shelf or basket

to access the light assembly.

2. The light bulb cover opens from the back. Firmly press

forward on the notches in the back of the cover and pull the

cover down.

3. Remove the cover and replace the burned-out bulb with an

appliance bulb no greater than 40 watts.

4. Insert the front tabs of the cover into the liner and snap the

back portion of the cover over the light assembly.

5. Plug in refrigerator or reconnect power.

Power Interruptions

If the power will be out for 24 hours or less, keep the door or

doors closed (depending on your model) to help food stay cold

and frozen.

If the power will be out for more than 24 hours, do one of the

following:

■ Remove all frozen food and store it in a frozen food locker.

■ Place 2 lbs (907 g) of dry ice in the freezer for every cubic foot

(28 L) of freezer space. This will keep the food frozen for 2 to

4days.

■ If neither a food locker nor dry ice is available, consume or

can perishable food at once.

REMEMBER: A full freezer stays cold longer than a partially filled

one. A freezer full of meat stays cold longer than a freezer full of

baked goods. If you see that food contains ice crystals, it may be

refrozen, although the quality and flavor may be affected. If the

condition of the food is poor, dispose of it.

Vacation and Moving Care

Vacations

If You Choose to Leave the Refrigerator On While You’re

Away:

1. Use up any perishables and freeze other items.

2. If your refrigerator has an automatic ice maker:

■ Raise wire shutoff arm to OFF (up) position.

■ Shut off water supply to the ice maker.

3. Empty the ice bin.

If You Choose to Turn the Refrigerator Off Before You

Leave:

1. Remove all food from the refrigerator.

2. If your refrigerator has an automatic ice maker:

■ Turn off the water supply to the ice maker at least one day

ahead of time.

■ When the last load of ice drops, raise the wire shutoff arm

to the OFF (up) position.

3. Turn the Temperature controls off. See “Using the Controls.”

4. Clean refrigerator, wipe it, and dry well.

5. Tape rubber or wood blocks to the tops of both doors to prop

them open far enough for air to get in. This stops odor and

mold from building up.

Moving

When you are moving your refrigerator to a new home, follow

these steps to prepare it for the move.

1. If your refrigerator has an automatic ice maker:

■ Turn off the water supply to the ice maker at least one day

ahead of time.

■ Disconnect the water line from the back of the

refrigerator.

■ When the last load of ice drops, raise the wire shutoff arm

to the OFF (up) position.

2. Remove all food from the refrigerator and pack all frozen

food in dry ice.

3. Empty the ice bin.

4. Turn the Temperature controls off. See “Using the Controls.”

5. Unplug refrigerator.

6. Clean, wipe, and dry thoroughly.

7. Take out all removable parts, wrap them well, and tape them

together so they don’t shift and rattle during the move.

8. Depending on the model, raise the front of the refrigerator so

it rolls more easily OR screw in the leveling legs so they don't

scrape the floor. See “Adjust the Doors.”

9. Tape the doors closed and tape the power cord to the back

of the refrigerator.

When you get to your new home, put everything back and refer to

the “Installation Instructions” section for preparation instructions.

Also, if your refrigerator has an automatic ice maker, remember to

reconnect the water supply to the refrigerator.

TROUBLESHOOTING

Try the solutions suggested here first in order to avoid the cost of an unnecessary service call.

Your refrigerator will not operate

■ Is the power cord unplugged? Plug into a grounded 3 prong

outlet.

■ Has a household fuse blown, or has a circuit breaker

tripped? Replace the fuse or reset the circuit breaker. If the

problem continues, call an electrician.

■ Is the Refrigerator Control turned to the OFF position?

See “Using the Control(s),” depending on the model.

■ Is the refrigerator defrosting? Recheck to see whether the

refrigerator is operating in 30 minutes. Your refrigerator will

regularly run an automatic defrost cycle.

The lights do not work

■ Is a light bulb loose in the socket or burned out? See

“Changing the Light Bulb(s),” depending on the model.

There is water in the defrost drain pan

■ Is the refrigerator defrosting? The water will evaporate. It is

normal for water to drip into the defrost pan.

■ Is it more humid than normal? When it is humid, expect that

the water in the defrost pan will take longer to evaporate.

The motor seems to run too much

■ Is the room temperature hotter than normal? The motor

will run longer under warm conditions. At normal room

temperatures, your motor will run about 40% to 80% of the

time. Under warmer conditions, it will run even more.

■ Has a large amount of food just been added to the

refrigerator? Adding a large amount of food warms the

refrigerator. The motor normally will run longer to cool the

refrigerator back down.

■ Are the doors opened often? The motor will run longer

when this occurs. Conserve energy by getting all items out at

one time, keeping food organized, and closing the door as

soon as possible.

■ Is the control set correctly for the surrounding

conditions? See “Using the Control(s),” depending on the

model.

■ Are the doors closed completely? Close the doors firmly. If

they do not close completely, see “The doors will not close

completely” later in this section.

■ Are the condenser coils dirty? This obstructs air transfer

and makes the motor work harder. Clean the condenser coils.

See “Cleaning.”

NOTE: Your new refrigerator will run longer than your old one due

to its high-efficiency motor.

The refrigerator seems to make too much noise

■ The sounds may be normal for your refrigerator. See

“Normal Sounds.”

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

The ice maker is not producing ice or not enough ice

■ Has the ice maker just been installed? Wait 72 hours for full

ice production to begin. Once your refrigerator is cooled, the

ice maker should produce 70-120 cubes every 24 hours.

■ Is the freezer temperature cold enough to produce ice?

Wait 24 hours after hookup for ice production. See “Using the

Control(s),” depending on the model.

■ Is the wire shutoff arm in the OFF (arm up) position?

Lower the wire shutoff arm to the ON (arm down) position.

See “Ice Maker.”

■ Is the water line shutoff valve to the refrigerator turned

on? Turn on the water valve. See “Connect the Water

Supply.”

■ Does the ice maker mold have water in it or has no ice

been produced? Be sure your refrigerator has been

connected to a water supply and the supply shutoff valve is

turned on. See “Connect the Water Supply.”

■ Is an ice cube jammed in the ejector arm? Remove the ice

from the ejector arm with a plastic utensil. See “Ice Maker.”

■ Has a large amount of ice just been removed? Allow

24 hours for ice maker to produce more ice.

■ Is the control set correctly? If too little ice is produced, see

“Using the Control(s),” depending on the model.

■ Is there a water filter installed on the refrigerator? The

filter may be full or incorrectly installed. Depending on your

model, remove the water filter cartridge. See “Water Filtration

System.” Operate the dispenser. If the water flow increases

noticeably, your filter is full and needs to be replaced.

■ Is a reverse osmosis water filtration system connected to

your cold water supply? See “Water Supply Requirements.”

NOTE: If not due to any of the above, there may be a problem

with the water line. Call for service.

Off-taste, odor or gray color in the ice

■ Are the plumbing connections new, causing discolored or

off-flavored ice? Discard the first few batches of ice.

■ Have the ice cubes been stored too long? Throw old ice

away and make a new supply.

■ Has food in the refrigerator been wrapped properly? See

“Refrigerator Features.”

■ Do the freezer and ice bin need to be cleaned? See

“Cleaning.”

■ Does the water contain minerals (such as sulfur)? A filter

may need to be installed to remove the minerals.

■ Is there a water filter installed on the refrigerator?

Gray or dark discoloration in ice indicates that the water

filtration system needs additional flushing. Run additional

water through the water dispenser to flush the water filtration

system more thoroughly, at least 2 to 3 gal. (8 to 12 L) or

5 minutes initially. Discard discolored ice.

The water dispenser will not operate properly

■ Has the water system not filled? The water system needs

to be filled the first time it is used. Use a sturdy container to

depress the water dispenser until water begins to flow.

Dispense and discard 2 to 3 gal. (8 to 12 L) of water. This will

take approximately 5 minutes and will help clear air from the

line. Additional flushing may be required in some households.

See “Water Dispenser.”

■ Is the water shutoff valve not turned on or the water line

connected at the source? Be sure the water shutoff valve is

turned on and the water source is connected to the

refrigerator. See “Connect the Water Supply.”

■ Is the water shutoff valve clogged or incorrectly installed?

See “Connect the Water Supply.” If clogging or installation is

not a problem, call for service or contact a plumber.

■ Is there a kink in the home water source line? If you find or

suspect a kink in the water line, contact a licensed, qualified

plumber.

■ Is there a water filter installed on the refrigerator? The

filter may be clogged or incorrectly installed. First, check the

filter installation instructions to ensure that the filter was

installed correctly and is not clogged. If installation or

clogging is not a problem, call for service.

■ Is a reverse osmosis water filtration system connected to

your cold water supply? See “Water Supply Requirements.”

Water flow from the dispenser decreases noticeably

■ Is there a water filter installed on the refrigerator? The

filter may be full or incorrectly installed. Depending on your

model, remove the water filter cartridge. See “Water Filtration

System.” Operate the dispenser. If the water flow increases

noticeably, your filter is full and needs to be replaced.

Water leaking from the dispenser

■ Is the glass not being held under the water dispenser long

enough? Hold the container under the water dispenser 2 to

3 seconds after releasing the dispenser lever. Water may

continue to dispense during this time.

■ Is there a water filter installed on the refrigerator? The

water filtration system may have air in the lines, causing water

to drip. Additional flushing may help clear air from the lines.

Normal dispenser use should flush air from the lines within

24 to 72 hours.

La page charge ...

KitchenAid 12828154 Manuel utilisateur

Marque: KitchenAid

Modèle: 12828154

Catégorie: Frigos

Taper: Manuel utilisateur

Ce manuel convient également à

Refrigerator 12828154

Télécharger le PDF

rapport

dans d''autres langues

English: KitchenAid 12828154 User manual

KitchenAid 12828154 Manuel utilisateur

Ce manuel convient également à

KitchenAid 12828154 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents