A: 9300 S.W. Gemini Drive Beaverton, OR 97008 USA W: www.biamp.com
PRODUCT DESCRIPTION
Modena Node X 100 and Modena Hub X 100 are presentation hubs. They
allow participants to connect to meeting room AV equipment and USB
accessories wirelessly, and enable any participant to wirelessly receive AV
streams during a video conferencing session.
These devices also connect to AV peripherals via USB and HDMI, and can
support multiple USB devices via a standard USB hub or by connecting a
Devio SCR-20 or SCR-25.
The information provided by this manual relates to physical connections and
device setup.
SETUP AND USE
User devices must be running on Windows, Mac OS X, iOS or Android
operating systems with the Node and Hub's custom drivers and user software
installed.
• Coordinate with local IT administrators before adding Hub or any other
device to a corporate network.
• Should not be placed near potential WiFi obstacles (walls, metallic
surfaces, other radio equipment or signals etc.).
• Keep the Hub away from other devices with a strong electromagnetic
reference such as cordless phones and microwaves.
• Do not exceed the maximum ambient operating temperature of 32-104° F
(0-40° C). Be aware of conditions in an enclosed rack that may cause the
temperature to exceed ambient room conditions.
MODENA
Node X 100 & Hub X 100
Installation & Operation Guide
JUN 2022
page 2 Installation and Operation Guide Modena Node/Hub
1. DCIN and Power
Connects with included power supply (12V).
2. NETWORK
The Node and Hub use a standard RJ45 network port with gigabit Ethernet
capability. Connect to the LAN with Cat5e or better cables (not included).
3. USB-A
The standard USB 3.0 Type-A port connects USB Video Class (UVC) devices,
such as USB webcams and all-in-one USB devices containing cameras,
microphones and loudspeakers.
4. HDMI
The standard HDMI port is used as a local video input/output. It connects to
display monitors, touchscreens or projectors via a standard HDMI cable (not
included).
5. USB-C
Connects to other USB-C devices and can also power the unit.
Node/Hub Back Panel
1
2
35
CONNECTIONS
4
page 3 Installation and Operation Guide Modena Node/Hub
Modena Node X 110 and Hub X 100 Installation
The Modena Node and Hub may be installed in almost any location that is
convenient for the room design, requirements, etc. This includes installation
on a wall behind a typical conference room display or under a table. Be sure to
allow for adequate airflow on the ventilation grilles.
Install away from heat sources such as vents, radiators, heat registers and
stoves. Also avoid installing near water or steam. Do not exceed the maximum
ambient operating temperature of 32-104° F (0-40° C).
Optional Wall-Mount Bracket
A wall-mount bracket comes installed on the device and may easily be
removed. The following hardware is included for mounting the Node/Hub with
the attached bracket.
Figure 1. Modena Node X 100 and Hub X 100 with Bracket
Remove the four screws that secure the mounting bracket to the devices as
shown in Figure 2 if required.
1. Determine the location where the Node/Hub is to be installed.
2. Install the devices with attached bracket at the desired location shown in
Figure 3.
Figure 3. - Wall installation
Figure 2. Bracket Removal
Bracket Removal
Wall-Mount Installation
Modena Node/Hub Installation and Operation Guide page 4
Wall-Mount Installation Continued
3. Secure the cables between the tabs on the cable management tray as
shown in Figure 4.
Figure 4. - Node and Hub with cables and management tray
Figure 5. - Node and
Hub tray cover
Figure 6. - Node and Hub with
cables and management tray
Figure 7. Secure cover
4. Once the cables are secure, place the tray cover as shown in Figures 5
and 6 (cables not shown).
5. Use included screw to secure the cover to the tray as shown in Figure 7.
A: 9300 S.W. Gemini Drive Beaverton, OR 97008 USA W: www.biamp.com
Note: Every eort has been made to ensure that the information contained in this manual was
complete and accurate at the time of printing. However, due to ongoing technical advances,
changes or modications may have occurred that are not covered in this manual. The latest
version is available at www.biamp.com.
JUN 2022
CONTACT US
Email
Web
support.biamp.com
Warranty
www.biamp.com/legal/warranty-information
Safety and Compliance
www.biamp.com/compliance
FCC warning: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
This device and its antenna(s) must not be co-located or operating in conjunction with any
other antenna or transmitter.
This equipment should be installed and operated with minimum distance 20cm between
the radiator and your body.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the followingmeasures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
FCC ID: 2A6N3-X100
IC warning:
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1) this device may not cause interference,
(2) this device must accept any interference, including interference that may cause
undesired operation of the device.
This Class [B] digital apparatus complies with Canadian ICE-003.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1)
l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter
tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
L'appareil a été évalué pour répondre aux exigences générales d'exposition RF.
L'appareil peut être utilisé dans des conditions d'exposition fixes / mobiles.
La distance de séparation minimale est de 20 cm.
Operating Frequency Range band 5150-5250 MHz “for indoor use only.”
-
1
-
2
-
3
-
4
-
5
-
6
-
7
