Yard-Man YM137 Manuel utilisateur

Marque: Yard-Man

Modèle: YM137

Catégorie: Coupe-herbe

Taper: Manuel utilisateur

Ce manuel convient également à

Trimmer YM137

Operator’s Manual

PART NO. 769-02490 (7/06)

English

Straight Shaft

Electric Trimmer

Model

YM137

SAVE THESE INSTRUCTIONS DO NOT THROW AWAY

INTRODUCTION

Copy the serial number

here:

THANK YOU

Thank you for buying this quality product. This modern

outdoor power tool will provide many hours of useful

service. You will find it to be a great labor-saving device.

This operator’s manual provides you with easy-to-

understand operating instructions. Read the whole

manual and follow all the instructions to keep your new

outdoor power tool in top operating condition.

PRODUCT REFERENCES, ILLUSTRATIONS

AND SPECIFICATIONS

All information, illustrations, and specifications in this

manual are based on the latest product information

available at the time of printing. We reserve the right to

make changes at any time without notice.

Reserved.

SERVICE INFORMATION

Service on this unit both within and after the warranty

period should be performed only by an authorized and

approved service dealer.

For service call 1-800-345-8746, or 1-800-668-1238 in

Canada to obtain a list of authorized service dealers near

you. For more details about your unit, visit our website at

www.yardman.com.

If you have difficulty assembling this product or have any

questions regarding the controls, operation or main-

tenance of this unit, please call the Customer Support

Department.

DO NOT RETURN THE UNIT TO THE RETAILER.

PROOF OF PURCHASE WILL BE REQUIRED FOR

WARRANTY SERVICE.

S/N :

ITEM :

MODEL :

Make sure you carefully read and understand this manual before starting or operating this equipment.

THIS PRODUCT IS COVERED BY ONE OR MORE U.S. PATENTS. OTHER PATENTS PENDING.

TABLE OF CONTENTS

Service Information . . . . . . . . . . . . . . . . . . . . . . . . .2

Rules for Safe Operation . . . . . . . . . . . . . . . . . . . . .3

Know Your Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Assembly Instructions . . . . . . . . . . . . . . . . . . . . . . .7

Operating Instructions . . . . . . . . . . . . . . . . . . . . . . .8

Maintenance and Repair Instructions . . . . . . . . . . .11

Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . .14

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Warranty Information . . . . . . . . . . . . . . . . . . . . . . .18

Parts List . . . . . . . . . . . . . . . . . . . .Inside Back Cover

Copy the model and parent

part number here:

Before beginning, locate the unit’s model plate. It lists

the model and serial numbers of your unit. Refer to the

sample plate below and copy the information for future

reference.

SYMBOL MEANING

The purpose of safety symbols is to attract your

attention to possible dangers. The safety symbols,

and their explanations, deserve your careful attention

and understanding. The safety warnings do not by

themselves eliminate any danger. The instructions or

warnings they give are not substitutes for proper

accident prevention measures.

NOTE: Advises you of information or instructions vital

to the operation or maintenance of the

equipment.

SYMBOL MEANING

READ ALL INSTRUCTIONS

BEFORE OPERATING

• Read the instructions carefully. Be familiar with the

controls and proper use of the unit.

• Do not operate this unit when tired, ill or under the

influence of alcohol, drugs or medication.

• Children and teens under the age of 15 must not use

the unit, except for teens guided by an adult.

• Inspect the unit before use. Replace damaged parts.

Make sure all fasteners are in place and secure.

Replace cutting attachment parts that are cracked,

chipped or damaged in any way. Make sure the cutting

attachment is properly installed and securely fastened.

Be sure that the cutting attachment shield is properly

attached, and positioned as recommended. Failure to

do so can result in personal injury to the operator and

bystanders, as well as damage to the unit.

• This unit was not designed to be used as a

brushcutter. Do not attach or operate this unit with any

type of brushcutting blade or brushcutting attachment.

• Use only a 0.080-inch (2.03 mm) diameter original

equipment manufacturer replacement line. Never use

metal-reinforced line, wire, chain or rope. These can

break off and become dangerous projectiles.

• Be aware of risk of injury to the head, hands and feet.

• Clear the area to be cut before each use. Remove

rocks, broken glass, nails, wire, string and other

objects which may be thrown or become entangled in

the cutting attachment. Clear the area of children,

bystanders and pets; keep them outside a 50-foot

(15 m.) radius, at a minimum. Even then, they are still

at risk from thrown objects. Encourage bystanders to

wear eye protection. If you are approached, stop the

unit immediately.

ELECTRICAL SAFETY WARNINGS

• Since the tool is double-insulated, a 2-wire extension

cord (an extension cord without a ground) may be

used. A 3-wire extension cord (an extension cord with

a ground) that uses a NEMA type connector (parallel

blade, U ground) is recommended. Extension cords

are available from your local retailer. Use only round-

jacketed extension cords approved for outdoor use.

• This tool is double-insulated. Repair or replace damaged

cords.

RULES FOR SAFE OPERATION

When using the unit,

you must follow the

safety rules. Please read these instructions

before operating the unit in order to ensure

the safety of the operator and any bystanders.

Please keep these instructions for later use.

WARNING:

• IMPORTANT SAFETY INSTRUCTIONS •

Failure to obey a

safety warning can

result in injury to yourself and others.

Always follow the safety precautions to

reduce the risk of fire, electric shock and

personal injury.

WARNING:

Failure to obey a

safety warning will

result in serious injury to yourself or to

others. Always follow the safety precautions

to reduce the risk of fire, electric shock and

personal injury.

DANGER:

Failure to obey a

safety warning may

result in property damage or personal injury

to yourself or to others. Always follow the

safety precautions to reduce the risk of fire,

electric shock and personal injury.

CAUTION:

Indicates

danger,

warning or caution. Attention is required in

order to avoid serious personal injury. May

be used in conjunction with other symbols

or pictographs.

SAFETY ALERT:

When using electric

gardening appliances,

basic safety precautions should always be

followed to reduce the risk of fire, electric shock

and personal injury. Carefully read and

understand the entire operator's manual before

using your unit. Pay close attention to the

operating instructions and safety warnings.

DANGER:

To reduce the risk of

electrical shock, use

only SW-A, SOW-A, STW-A, STOW-A, SJW-A,

SJOW-A, SJTW-W or SJTOW-A cord types.

WARNING:

• To reduce the risk of electrical shock, this unit has a

polarized plug (one blade is wider than the other). This

unit will fit with a polarized plug in one way only. If the

plug does not fit fully into the unit, reverse the plug. If

it still does not fit, use a cord with the correct

connection. Do not modify the unit in any way.

*The wire size (AWG) for appliances using 12 to 16

amps is 14 AWG for 25 feet, 12 AWG for 50 feet, and

not recommended for 100 or 150 feet.

• CORD SETS: Make sure your cord set is in good

condition, with a cord that is heavy enough to carry

the current that your unit will draw. An undersized cord

set will cause a drop in line voltage resulting in a loss

of power, as well as overheating. The table shown

above illustrates the correct size to use depending on

the cord length and nameplate amperage rating. If in

doubt, use the next heavier size line gauge. The

smaller the gauge number, the heavier the cord. To

prevent the cord from disconnecting from the unit, use

the cord hook shown in the Operating Instructions.

• Ground Fault Circuit Interrupter (GFCI) protection

should be provided on the circuit(s) or outlet(s) that will

be used for the unit. Use receptacles with built-in

GFCI protection for an extra measure of safety.

• Do not abuse the power cord. Never carry the unit by

the cord or yank the cord to disconnect from receptacle.

Keep the cord from heat, oil and sharp edges.

• A nameplate on your unit indicates the voltage used.

Never connect the unit to an AC voltage that differs

from this voltage.

• Inspect all extension cords and the unit power connection

periodically. Look closely for deterioration, cuts or cracks

in the insulation. Also inspect the connections for damage.

Repair or replace the cords if any defects appear.

• Avoid dangerous environments. Never operate your unit

in damp or wet conditions. Moisture is a shock hazard.

• Do not use the unit in the rain.

• Do not handle the plug or the unit with wet hands.

WHILE OPERATING

• Wear safety glasses or goggles that are marked as

meeting ANSI Z87.1-1989 standards. Also wear

ear/hearing protection when operating this unit. Wear

a face or dust mask if the operation is dusty. Long

sleeve shirts are recommended.

• Wear heavy, long pants, boots and gloves. Do not

wear loose clothing, jewelry, short pants, sandals or

go barefoot. Secure hair above shoulder level.

• The cutting attachment shield must always be in place

while operating the unit. Do not operate unit without

both trimming lines extended, and the proper line

installed. Do not extend the trimming line beyond the

length of the shield.

• Adjust the D-handle to your size to provide the best

grip.

• Be sure the cutting attachment is not in contact with

anything before starting the unit.

• Use the unit only in daylight or good artificial light.

• Avoid accidental starting. Do not carry around a unit

that is plugged in with your finger on the trigger

switch. Be sure the switch is in the off position when

plugging in the unit.

• Use the right tool. Only use this tool for its intended

purpose.

• Do not overreach. Always keep proper footing and

balance.

• Always hold the unit with both hands when operating.

Keep a firm grip on both handles or grips.

• Keep hands, face, and feet at a distance from all

moving parts. Do not touch or try to stop the cutting

attachment when it rotates.

• Always stop the motor when cutting is delayed or

when walking from one cutting location to another.

• If you strike or become entangled with a foreign

object, stop the motor immediately and check for

damage. Do not operate before repairing damage. Do

not operate the unit with loose or damaged parts.

• Stop the unit and unplug it for maintenance or repair.

• Use only genuine original equipment manufacturer

replacement parts and accessories for this unit. These

are available from your authorized service dealer. Use

of any non-original parts or accessories could lead to

serious injury to the user, or damage to the unit, and

void your warranty.

• Keep unit clean of vegetation and other materials.

They may become lodged between the cutting

attachment and shield.

OTHER SAFETY WARNINGS

• Be sure to secure the unit while transporting.

• Store the unit in a dry area, locked up to prevent

unauthorized use or damage, and stored in a high

place out of the reach of children.

• Never douse or squirt the unit with water or any other

liquid. Keep handles dry, clean and free from debris.

Clean after each use. See the Cleaning and Storage

instructions.

• Keep these instructions. Refer to them often and use

them to instruct other users. If you loan someone this

unit, also loan them these instructions.

SAVE THESE INSTRUCTIONS

RULES FOR SAFE OPERATION

Cord length (ft.) 25 50 100 150

Wire size (AWG)* 16 16 16 14

MINIMUM WIRE SIZE FOR EXTENSION CORDS FOR

120 VOLT APPLIANCES USING 0-12 AMPS*

RULES FOR SAFE OPERATION

SYMBOL MEANING

• SAFETY ALERT SYMBOL

Indicates danger, warning, or

caution. May be used in conjunction

with other symbols or pictographs.

• WARNING - READ

OPERATOR'S MANUAL

Read the Operator’s Manual(s) and

follow all warnings and safety

instructions. Failure to do so can

result in serious injury to the

operator and/or bystanders.

• WEAR EYE AND HEARING

PROTECTION

WARNING:Thrown

objects and loud noise can cause

severe eye injury and hearing loss.

Wear eye protection meeting ANSI

Z87.1-1989 standards and ear

protection when operating this unit.

Use a full face shield when needed.

• THROWN OBJECTS AND

ROTATING CUTTER CAN

CAUSE SEVERE INJURY

WARNING:Keep clear

of blower outlet. Never point the

blower at yourself or others. Objects

can be thrown from blower. Do not

operate unit without proper

attachments and guards in place.

SAFETY AND INTERNATIONAL SYMBOLS

This operator's manual describes safety and international symbols and pictographs that may appear on this product.

Read the operator's manual for complete safety, assembly, operating and maintenance and repair information.

SYMBOL MEANING

• DO NOT USE IN THE RAIN

WARNING: Avoid

dangerous environments. Never

operate your unit in the rain, or in

damp or wet conditions. Moisture is

a shock hazard.

• KEEP BYSTANDERS AWAY

WARNING:Keep all

bystanders, especially children and

pets, at least 50 feet (15 m.) from the

operating area.

• THROTTLE CONTROL

Indicates “HIGH” or “FASTEST” speed.

• THROTTLE CONTROL

Indicates “IDLE”, “LOW” or

“SLOWEST” speed.

• DOUBLE INSULATED

Two systems of insulation are

provided instead of grounding.

There is no grounding provided

and no means of grounding should

be added to this unit.

RULES FOR SAFE OPERATION

KNOW YOUR UNIT

As a trimmer:

• Cutting grass and light weeds

• Decorative trimming around trees, fences, etc.

Cutting Attachment

Shield

D-Handle

Cutting Attachment

Shaft Housing

Line Cutting Blade

Housing Grip

Switch Trigger

Recessed

Plug

Motor Housing

Switch Trigger

Two-Speed

Switch

EZ-Link™

Cord Hook

Shoulder

Harness

ASSEMBLY INSTRUCTIONS

INSTALL THE CUTTING ATTACHMENT SHIELD

Use the following instructions if the cutting attachment

shield on your unit is not installed or if you ever need to

re-install it.

1. Slide the cutting attachment shield into the shield

mount on the cutting attachment. Align the screw

holes in the shield with the holes in the cutting

attachment (Fig. 3).

Fig. 3

Fig. 5

Fig. 4

Cutting Attachment

Shield

Screws

Shaft Housing

Hex Lock Nut

Cutting Attachment

Shield

Cutting Attachment

2. Place a hex lock nut into one of the three recessed

holes on the top of the cutting attachment shield (Fig 4).

3. Install a screw into the hole from the bottom of the

cutting attachment shield and screw it into the nut

installed in step 2 (Fig 5). Do not tighten.

4. Repeat steps 2 and 3 until all three screws have

been started, then tighten securely.

Recessed Holes

Shield Mount

Never operate the

trimmer without the

cutting attachment shield in place to

prevent serious personal injury.

WARNING:

INSTALL AND ADJUST THE D-HANDLE

1. Push the D-handle down onto the shaft housing and

push it on the boom (Fig. 1). The squared bolt hole in

the handle is to the right.

2. Insert the shoulder bolt into the squared hole in the

handle and push through. On the left side of the

handle, place the washer on the bolt, then screw the

wing nut onto the bolt. Do not tighten until you make

the handle adjustment.

NOTE: If the D-handle was pre-installed, loosen the wing

nut on it just enough so it is movable.

3. Rotate the D-handle to place the grip above the top

of the shaft housing. Place it a minimum of 6 inches

(15.24 cm) from the end of the housing.

4. While holding the unit in the operating position

(Fig. 2), position the D-handle to the location that

provides you the best grip.

5. Tighten the wing nut until the D-handle is secure.

Fig. 1

Fig. 2

OPERATING INSTRUCTIONS

For decorative trimming/edging with the line head cutting

attachment, lock the release button of the cutting

attachment into the 90° hole or the 180° hole (Fig. 8).

For edging with the edger add-on, lock the release

button of the cutting attachment only into the 180°

trimming hole/ primary hole (Fig. 8).

OPERATING THE EZ-LINK™ SYSTEM

The EZ-Link™ system enables the use of these optional

Add-Ons:

Blower/Vacuum . . . . . . . . . . . . . . . . . . . . . . . . . . BV720r

Cultivator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GC720r

Edger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LE720r

Snow Thrower . . . . . . . . . . . . . . . . . . . . . . . . . . . ST720r

Straight Shaft Trimmer . . . . . . . . . . . . . . . . . . . . SS725r

Tree Pruner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TP720r

Turbo Blower . . . . . . . . . . . . . . . . . . . . . . . . . . . . TB720r

Removing the Cutting Attachment or Add-Ons

1. Turn the knob counterclockwise to loosen (Fig. 6).

2. Press and hold the release button (Fig. 6).

3. While firmly holding the upper shaft housing, pull

the cutting attachment or add-on straight out of the

EZ-Link™ coupler (Fig. 7).

Installing the Cutting Attachment or Add-Ons

NOTE: To make installing or removing the add-on

easier, place the unit on the ground or on a work

bench.

1. Turn knob counterclockwise to loosen (Fig. 6).

Fig. 6

EZ-Link™ Coupler

Release Button

Guide Recess

Knob

Primary Hole

Upper Shaft Housing

90˚ Edge

Trimming Hole

EZ-Link™ Coupler

2. While firmly holding the add-on, push it straight into

the EZ-Link™ coupler (Fig. 7).

NOTE: Aligning the release button with the guide recess

will help installation (Fig. 6).

3. Turn the knob clockwise to tighten (Fig. 8).

Fig. 7

Fig. 8

Knob

180˚ Trimming Hole/

Primary Hole

Lower Shaft Housing

Release Button

Prior to operation,

read and understand

the operator’s manual for unit to be used with

this add-on.

WARNING:

To avoid serious

personal injury and

damage to the unit, shut the unit off before

removing or installing add-ons.

WARNING:

The add-ons with the

coupler system is to

be used in the primary hole only. Using the

wrong hole could lead to personal injury or

damage to the unit.

CAUTION:

Lock the release

button in the primary

hole (Fig. 10) and securely tighten the knob

before operating this unit.

CAUTION:

OPERATING INSTRUCTIONS

Always wear eye,

hearing, foot and

body protection to reduce the risk of injury

when operating this unit.

WARNING:

CONNECTING THE CORD

Use the cord hook when connecting the extension cord to

the power cord outlet. This helps prevent any

disconnection.

1. Make a narrow loop with the extension cord.

2. Push the loop through the opening and move it onto

the hook on the motor housing (Fig. 9).

3. Plug the cord properly into the socket.

Only use outdoor-approved extension cords. Cord sets

are specified in the Important Safety Information section.

STARTING/STOPPING INSTRUCTIONS

Once the unit is plugged in, stand in the operating

position (Fig. 11). Squeeze the trigger to start the unit. To

stop the unit, release the trigger (Fig. 10).

Trigger

HOLDING THE TRIMMER

Before operating the unit, stand in the operating position

(Fig. 11). Check for the following:

• The operator is wearing eye protection and proper

clothing

• With a slightly-bent right arm, the operator’s hand is

holding the shaft grip

• The operator’s left arm is straight, the left hand

holding the D-handle

• The unit is at waist level

•

The cutting attachment is parallel to the ground and

easily contacts the grass without the need to bend ove

• The extension cord is safely behind the operator

Fig. 11

ADJUSTING TRIMMING LINE LENGTH

The Bump Head™ cutting attachment allows you to

release trimming line without stopping the motor. To

release more line, lightly tap the cutting attachment on the

ground (Fig. 12) while operating the trimmer at high speed.

NOTE: Always keep the trimming line fully extended.

Line release becomes more difficult when the

cutting line gets shorter.

Always wear eye,

hearing, foot and

body protection to reduce the risk of injury

when operating this unit.

WARNING:

Fig. 9

TWO-SPEED SWITCH

This unit is equipped with a two-speed switch: a

powerful high speed for demanding yard work, and a

precision low speed for light-duty yard work.

Push the switch up for high speed trimming. Push the

switch down for low speed trimming (Fig. 10).

Fig. 10

OPERATING INSTRUCTIONS

TIPS FOR BEST TRIMMING RESULTS

• Keep the cutting attachment parallel to the ground.

• Do not force the cutting attachment. Allow the tip of

the line to do the cutting, especially along walls.

Cutting with more than the tip will reduce cutting

efficiency and may overload the motor.

• Cut grass over 8 inches (200 mm) by working from

top to bottom in small increments to avoid

premature line wear or motor drag.

Fig. 12

Each time the head is bumped, about 1 inch (25.4 mm)

of trimming line releases. A blade in the cutting

attachment shield will cut the line to the proper length if

any excess line is released.

For best results, tap the bump knob on bare ground or

hard soil. If you attempt a line release in tall grass, the

motor may stall. Always keep the trimming line fully

extended. Line release becomes more difficult when the

cutting line gets shorter.

NOTE: Do not rest the Bump Head™ on the ground

while the unit is running.

Some line breakage will occur from:

• Entanglement with foreign matter

• Normal line fatigue

• Attempting to cut thick, stalky weeds

• Forcing the line into objects such as walls or fence

posts

Do not remove or alter

the line cutting blade

assembly. Excessive line length will make the

clutch overheat. This may lead to serious

personal injury or damage to the unit.

CAUTION:

DECORATIVE TRIMMING

Decorative trimming is accomplished by removing all

vegetation around trees, posts, fences and more.

Rotate the whole unit so that the cutting attachment is at

a 30° angle to the ground (Fig. 13).

Fig. 13

• Cut from right to left whenever possible. Cutting to

the left improves the unit's cutting efficiency.

Clippings are thrown away from the operator.

• Slowly move the trimmer into and out of the cutting

area at the desired height. Move either in a forward-

backward or side-to-side motion. Cutting shorter

lengths produces the best results.

• Trim only when grass and weeds are dry.

• The life of your cutting line is dependent upon:

• Following the trimming techniques

• What vegetation is being cut

• Where vegetation is cut

For example, the line will wear faster when trimming

against a foundation wall as opposed to trimming

around a tree.

MAINTENANCE AND REPAIR INSTRUCTIONS

SERVICING DOUBLE INSULATED UNITS

This unit is double-insulated. In a double-insulated unit,

two systems of insulation are provided instead of

grounding. There is no grounding provided and no

means of grounding should be added to this unit.

Extreme care and knowledge of the system is required

when servicing a double-insulated unit. Service should

be performed by qualified service personnel only.

Replacement parts for a double-insulated unit must be

identical to the parts they replace. Refer any repair to an

authorized service dealer. A double-insulated unit is

marked with the words “double insulation” or “double

insulated.”

LINE INSTALLATION FOR THE SPEEDSPOOL

Always use original equipment manufacturer 0.080 inch

(2.03 mm) replacement line. Line other than the specified

may make the motor overheat or fail.

There are two methods to replace the SpeedSpool

trimming line:

• Wind the inner reel with new line

• Install a pre-wound inner reel

Winding the Inner Reel With New Line

NOTE: It Is unnecessary to remove the bump knob to

install a new trimming line.

1. Cut two pieces of 0.080 inch (2.03 mm) trimming

line, 10 feet (3 m) long.

2. Hold the outer spool and turn the inner reel

counterclockwise to line up the arrows on the outer

spool and inner reel (Fig. 14).

Top View Of The SpeedSpool

Outer Spool

Inner Reel

Fig. 14

Bump Knob

Arrows

Never use metal-

reinforced line, wire,

chain or rope. These can break off and

become dangerous projectiles.

WARNING:

Always use the

correct line length

when installing trimming line on the unit.

The line may not release properly if the line

is too long.

WARNING:

Trimming Line

Line Loading Hole

Eyelet

5. Insert the line into the locking hole. Do not push the

line more than a 1/2 inch (12.7 mm) into the line

locking hole. The line will form a small loop (Fig. 16)

when it is inserted correctly.

3. Pull old line out of the line loading and line locking

holes (Fig. 14 and 15).

4. Insert a piece of trimming line straight into one of the

two eyelets in the outer spool. Push it up through the

line loading hole in the inner reel (Fig. 15). Do not

bend the line when inserting it into the eyelet.

Fig. 15

6. Pull the line from the outer spool until the line is tight

against the inner reel (Fig. 17).

Fig. 17

INSTALLING A PRE-WOUND REEL

1. Turn the bump knob counterclockwise and remove

the bump knob, spring and foam seal (Fig. 20).

9. If winding the line becomes difficult or if the line

jams, pull the ends of the line from the spool

(Fig. 19). Continue winding the inner reel

counterclockwise.

Fig. 18

Fig. 19

7. Repeat procedures 4-6 with the second piece of line.

8. Hold the outer spool. Wind the inner reel

counterclockwise until approximately four (4) inches

(102 mm) of line remain (Fig. 18).

NOTE: Do not wind the inner reel before installing the

second piece of line.

Bump Knob

Foam Seal

Spring

Inner Reel

Fig. 20

2. Pull the old inner reel with existing line from the outer

spool.

3. Insert the ends of the prewound inner reel line into

the outer spool eyelets (Fig. 21). Push the new inner

reel, arrow side up, into the outer spool.

Fig. 21

Line Locking Hole

Fig. 16

4. Hold the inner reel in place and install the bump

knob, spring and foam seal. Press down and turn the

bump knob clockwise. Grasp the ends and pull firmly

to release the line from the holding slots in the inner

reel (Fig. 19).

MAINTENANCE AND REPAIR INSTRUCTIONS

SPEEDSPOOL REPLACEMENT PARTS

Replacement Line . . . . . . . . . . . . . . . . . . . . . . . . 181472

Replacement Line Cartridge . . . . . . . . . . . . . . . . 181460

Inner Reel Spring . . . . . . . . . . . . . . . . . . . . . . . . 181465

Foam Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181467

Inner Reel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181464

Bump Knob Assembly . . . . . . . . . . . . . . . . . . . . 181468

These SpeedSpool

replacement parts can be

purchased from your local authorized dealer.

Releasing the Inner Reel

If the SpeedSpool

does not release line correctly, pull

the ends of the line firmly from the spool (Fig. 19). If this

does not the release line, follow the Cleaning the

SpeedSpool

instructions.

4. Remove any existing line from the inner reel before

cleaning. Remove any debris or grass from the knob,

spring, inner reel and foam seal. Wash the inner reel

with warm soapy water (Fig. 23).

Fig. 22

CLEANING THE SPEEDSPOOL

Cleaning the SpeedSpool

may be necessary if:

• A jammed or excessive line must be removed

• The SpeedSpool

becomes difficult to wind or does

not operate correctly when bumping the head on the

ground

1. Hold the outer spool, and unscrew the bump knob

counterclockwise (Fig. 22).

2. Pull out the bump knob, spring and foam seal (Fig. 20).

Shaft

Plunger

7. Place the bump knob, spring and foam seal into the

inner reel (Fig. 20).

8. Press the bump knob down and tighten clockwise.

9. Install new line as described in Line Installation for

the SpeedSpool

5. Clean the shaft and the inner surface of the outer

spool. To clean the shaft underneath the plunger,

press down on the plunger (Fig. 24). Remove any dirt

or debris from the shaft.

NOTE: The inner reel must be totally dry before

reinstalling it into the outer spool. Do not lubricate

the inner reel or outer spool assembly.

6. Place the inner reel into the outer spool.

Fig. 24

Inner Reel

Fig. 23

3. Pull the inner reel with existing line from the outer

spool (Fig. 21).

CLEANING THE UNIT

Switch off the unit and disconnect it from the power

source. Use a small brush to clean off the outside of the

unit. Do not use strong detergents. Household cleaners

that contain aromatic oils such as pine and lemon, and

solvents such as kerosene, can damage plastic housing

or handle. Wipe off any moisture with a soft cloth. Also

keep the air vents free of obstructions.

STORAGE

• Store the unit locked up to prevent unauthorized use

or damage.

• Store the unit in a dry, well-ventilated area.

• Store the unit out of the reach of children.

INSPECT EXTENSION CORDS

Inspect all extension cords periodically. Look closely for

deterioration, cuts or cracks in the insulation. Inspect the

connectors for damage. Replace cords if defective or

damaged.

To avoid serious

personal injury,

always turn your unit off and unplug it

before you clean or service it.

WARNING:

MAINTENANCE AND REPAIR INSTRUCTIONS

TROUBLESHOOTING

If further assistance is required, contact your authorized service dealer.

CAUSE ACTION

Cutting attachment bound with grass Stop the motor and clean cutting attachment

Cutting attachment out of line Refill with new line

Inner reel bound up Replace the inner reel

Cutting head dirty Clean inner reel and outer spool

Line welded Disassemble, remove the welded section and rewind

Line twisted when refilled Disassemble and rewind the line

Not enough line is exposed Push the bump knob and pull out line until 4 inches

(102 mm) of line is outside of the cutting attachment

CAUSE ACTION

Unit is unplugged Check cord to make sure it is still plugged into an

electrical outlet

MOTOR WILL NOT START

CUTTING ATTACHMENT WILL NOT ADVANCE LINE

CAUSE ACTION

Oil, cleaner or lubricant in cutting head Clean and thoroughly dry the cutting head

CUTTING LINE ADVANCES UNCONTROLLABLY

SPECIFICATIONS

Motor type..........................................................................................................................................A.C.,120 Volts Electric

Operating RPM............................................................................................................................................ up to 7,800 rpm

Ignition Switch ........................................................................................................................................................... Trigger

Amperage............................................................................................................................................................... 5.5 amps

MOTOR

DRIVE SHAFT and CUTTING ATTACHMENT

Drive Shaft Housing....................................................................................................................................... Steel (EZ-Link)

Shoulder Strap ........................................................................................................................................................ Optional

Approximate Unit Weight (cutting attachment shield and D-handle)..................................................................9 lbs. (4 kg)

Cutting Mechanism................................................................................................ SpeedSpool

Dual String Cutting Head

Line Spool............................................................................................................................................. Bump Line Releaser

Line Spool Diameter .......................................................................................................................3 inches (76.2 mm)

Cutting Path Diameter................................................................................................................................... 15 in (381 mm)

Trimming Line Diameter .......................................................................................................................... 0.080 in (2.03 mm)

NOTES

MANUFACTURER’S LIMITED WARRANTY FOR:

No implied warranty, including any implied warranty of

merchantability or fitness for a particular purpose,

applies after the applicable period of express written

warranty above as to the parts as identified. No other

express warranty or guaranty, whether written or oral,

except as mentioned above, given by any person or

entity, including a dealer or retailer, with respect to any

product shall bind MTD. During the period of the

Warranty, the exclusive remedy is repair or replacement

of the product as set forth above. (Some states do not

allow limitations on how long an implied warranty lasts, so

the above limitation may not apply to you.)

The provisions as set forth in this Warranty provide the

sole and exclusive remedy arising from the sales. MTD

shall not be liable for incidental or consequential loss or

damages including, without limitation, expenses incurred

for substitute or replacement lawn care services, for

transportation or for related expenses, or for rental

expenses to temporarily replace a warranted product.

(Some states do not allow limitations on how long an implied

warranty lasts, so the above limitation may not apply to you.)

In no event shall recovery of any kind be greater than the

amount of the purchase price of the product sold. Alteration

of the safety features of the product shall void this Warranty.

You assume the risk and liability for loss, damage, or injury

to you and your property and/or to others and their property

arising out of the use or misuse or inability to use the

product.

This limited warranty shall not extend to anyone other than

the original purchaser, original lessee or the person for whom

it was purchased as a gift.

How State Law Relates to this Warranty: This warranty

gives you specific legal rights, and you may also have other

rights which vary from state to state.

To locate your nearest service dealer dial 1-800-345-8746

in the United States or 1-800-668-1238 in Canada.

MTD LLC

P.O. Box 361131

Cleveland, OH 44136-0019

The limited warranty set forth below is given by MTD

LLC (“MTD”) with respect to new merchandise purchased and

used in the United States, its possessions and territories.

MTD warrants this product against defects in material and

workmanship for a period of two (2) years commencing on the

date of original purchase and will, at its option, repair or

replace, free of charge, any part found to be defective in

material or workmanship. This limited warranty shall only apply

if this product has been operated and maintained in

accordance with the Operator’s Manual furnished with the

product, and has not been subject to misuse, abuse,

commercial use, neglect, accident, improper maintenance,

alteration, vandalism, theft, fire, water or damage because of

other peril or natural disaster. Damage resulting from the

installation or use of any accessory or attachment not

approved by MTD for use with the product(s) covered by this

manual will void your warranty as to any resulting damage. This

warranty is limited to ninety (90) days from the date of original

retail purchase for any MTD product that is used for rental or

commercial purposes, or any other income-producing purpose.

HOW TO OBTAIN SERVICE: Warranty service is available,

WITH PROOF OF PURCHASE THROUGH YOUR LOCAL

AUTHORIZED SERVICE DEALER. To locate the dealer in your

area, please check for a listing in the Yellow Pages or contact

the Customer Service Department of MTD LLC by calling

1-800-345-8746 or writing to P.O. Box 361131, Cleveland OH

44136-0019 or if in Canada call 1-800-668-1238. No product

returned directly to the factory will be accepted unless prior

written permission has been extended by the Customer

Service Department of MTD LLC.

This limited warranty does not provide coverage in the

following cases:

A. Tune-ups - Spark Plugs, Carburetor Adjustments, Filters.

B. Wear items - Bump Knobs, Outer Spools, Cutting Line,

Inner Reels, Starter Pulley, Starter Ropes, Drive Belts.

C. MTD does not extend any warranty for products sold or

exported outside of the United States of America, its

possessions and territories, except those sold through

MTD’s authorized channels of export distribution.

MTD reserves the right to change or improve the design of

any MTD Product without assuming any obligation to modify

any product previously manufactured.

Manuel de l'utilisateur

Français

PART NO. 769-02490 (7/06)

Désherbeuse

Electrique

Model

YM137

MANUEL IMPORTANT À NE PAS JETER

Copiez le numéro

de série ici :

Copiez le numéro de

modèle / pièce mère ici :

TOUS NOS REMERCIEMENTS

Nous vous remercions d'avoir acheté ce produit de

qualité. Cet outil mécanique de plein air moderne est

conçu pour vous rendre service pendant longtemps. Il

vous sauvera beaucoup de temps comme vous pourrez

vous en rendre compte. Ce manuel de l'utilisateur

comporte un mode d'emploi facile à comprendre. Prenez

soin de lire le manuel au complet et suivez toutes ses

instructions à la lettre afin de conserver votre nouvel outil

mécanique de plein air en excellent état de

fonctionnement.

RÉFÉRENCES, ILLUSTRATIONS ET

SPÉCIFICATIONS RELATIVES AU PRODUIT

Toutes les informations, illustrations et spécifications

contenues dans ce manuel tiennent compte des

dernières informations techniques disponibles au

moment de mettre sous presse. Nous nous réservons le

droit d'y apporter des modifications à tout moment, sans

préavis.

réservés.

NFORMATIONS D’ENTRETIEN

Tout entretien effectué sur cet appareil pendant et après

la période de garantie doit être fait par un concess-

ionnaire agréé uniquement. Obtenez la liste des

concessionnaires agréés appelez le 1-800-345-8746, ou

le 1-800-668-1238 au Canada. Pour de plus amples

informations à propos de votre appareil, visitez

www.yardman.com.

NE RETOURNEZ PAS L'APPAREIL AU DÉTAILLANT

CHEZ QUI VOUS L'AVEZ ACHETÉ. TOUT SERVICE

SOUS GARANTIE NÉCESSITE UNE PREUVE D'ACHAT.

Avant d'assembler votre nouvel équipement, repérez la

plaque signalétique de l'appareil et copiez ses

informations dans l'espace ci-dessous. Ces informations

sont essentielles si vous désirez obtenir de l'aide auprès

de notre service technique ou d'un distributeur agréé. Un

exemple de plaque signalétique est présenté ci-dessous.

S/N :

ITEM :

MODEL :

Prenez soin de lire et de bien comprendre ce manuel avant de démarrer ou de faire fonctionner cet équipement.

CE PRODUIT EST COUVERT PAR UN OU PLUSIEURS BREVETS AMÉRICAINS, ET D’AUTRES SONT EN INSTANCE.

TABLE DES MATIÈRES

Service technique . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Consignes de sécurité . . . . . . . . . . . . . . . . . . . . . . .3

Familiarisez-vous avec votre appareil . . . . . . . . . . .6

Instructions de montage . . . . . . . . . . . . . . . . . . . . . .7

Mode d'emploi . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Entretien et réparations . . . . . . . . . . . . . . . . . . . . .11

Tableau de dépannage . . . . . . . . . . . . . . . . . . . . . .14

Caractéristiques . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Garantie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Liste des pièces . . . .Intérieure de la Couverture Arrière

Numéro de modèle

Numéro de série

Numéro de pièce mère

INTRODUCTION

Si vous éprouvez des difficultés à assembler ce produit

ou si vous avez des questions concernant les

commandes, le fonctionnement ou l’entretien de cet

appareil, veuillez communiquer avec notre service

technique.

La page charge ...

Yard-Man YM137 Manuel utilisateur

Marque: Yard-Man

Modèle: YM137

Catégorie: Coupe-herbe

Taper: Manuel utilisateur

Ce manuel convient également à

Trimmer YM137

Télécharger le PDF

rapport

dans d''autres langues

English: Yard-Man YM137 User manual
español: Yard-Man YM137 Manual de usuario

Documents connexes

MTD YM132 Manuel utilisateur

Yard-Man YM137 Manuel utilisateur

Ce manuel convient également à

Yard-Man YM137 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents