Jenn-Air JIC4536XB Mode d'emploi

Marque: Jenn-Air

Modèle: JIC4536XB

Catégorie: Cuisinières

Taper: Mode d'emploi

JENN-AIR

30" AND 36" (76.2 CM AND 91.4 CM)

TOUCH-ACTIVATED ELECTRONIC

INDUCTION COOKTOP

TABLE DE CUISSON PAR INDUCTION AVEC

COMMANDES ÉLECTRONIQUES TACTILES JENN-AIR

DE 30" ET 36" (76,2 CM ET 91,4 CM)

Use & Care Guide

For questions about features, operation/performance, parts, accessories, or service in the U.S.A., call:

1-800-JENNAIR (1-800-536-6247), or visit our website at www.jennair.com.

In Canada, call: 1-800-807-6777, or visit our website at www.jennair.ca.

Guide d’utilisation et d’entretien

Au Canada, pour assistance, installation ou service, composez le 1-800-807-6777 ou visitez notre site web à www.jennair.ca.

Table of Contents/Table des matières ................... 2

501961901382B

IMPORTANT: READ AND SAVE THESE INSTRUCTIONS.

FOR RESIDENTIAL USE ONLY.

IMPORTANT : LIRE ET CONSERVER CES INSTRUCTIONS.

POUR UTILISATION RÉSIDENTIELLE UNIQUEMENT.

TABLE OF CONTENTS

COOKTOP SAFETY........................................................................2

COOKTOP USE ..............................................................................4

Induction Cooking........................................................................5

Cooktop Controls.........................................................................5

Dual Size Surface Cooking Area..................................................7

Sensor Boil ...................................................................................7

Low Settings.................................................................................8

Simmer .........................................................................................8

Melt...............................................................................................8

Keep Warm...................................................................................8

Bridge ...........................................................................................8

Pan Detection...............................................................................9

Control Lock.................................................................................9

Performance Boost Function.......................................................9

Timer...........................................................................................10

Tones..........................................................................................10

Ceramic Glass............................................................................10

Cookware ...................................................................................10

COOKTOP CARE..........................................................................11

General Cleaning........................................................................11

TROUBLESHOOTING ..................................................................12

ASSISTANCE OR SERVICE.........................................................13

WARRANTY ..................................................................................14

TABLE DES MATIÈRES

SÉCURITÉ DE LA TABLE DE CUISSON ....................................15

UTILISATION DE LA TABLE DE CUISSON................................17

Cuisson par induction ................................................................18

Commandes de la table de cuisson ..........................................18

Surface de cuisson à dimension double....................................20

Ébullition avec capteur...............................................................20

Réglages de chaleur réduite ......................................................21

Mijotage......................................................................................21

Faire fondre ................................................................................21

Maintien au chaud......................................................................21

Liaison ........................................................................................22

Détection d'un plat.....................................................................22

Verrouillage des commandes.....................................................22

Fonction d'optimisation du rendement......................................22

Minuterie.....................................................................................23

Signaux sonores.........................................................................23

Vitrocéramique ...........................................................................23

Ustensiles de cuisson ................................................................24

ENTRETIEN DE LA TABLE DE CUISSON ..................................24

Nettoyage général ......................................................................24

DÉPANNAGE.................................................................................25

ASSISTANCE OU SERVICE.........................................................26

GARANTIE.....................................................................................27

COOKTOP SAFETY

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

This induction cooktop generates and uses ISM frequency energy that heats cookware by using an electromagnetic field. It has been

tested and complies with Part 18 of the FCC Rules for ISM equipment. This induction cooktop meets the FCC requirements to minimize

interference with other devices in residential installation.

This induction cooktop may cause interference with television or radio reception. If interference occurs, the user should try to correct

the interference by:

Relocating the receiving antenna of the radio or television.

Increasing the distance between the cooktop and the receiver.

Connecting the receiver into a different outlet.

It is the user’s responsibility to correct any interference.

NOTE: People with a pacemaker or similar medical device should use care when standing near this induction cooktop while it is on. The

electromagnetic field may affect the pacemaker or similar device. Consult your doctor, or the manufacturer of the pacemaker or similar

medical device for additional information about its effects with electromagnetic fields of the induction cooktop.

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electrical shock,

injury to persons, or damage when using the cooktop, follow

basic precautions, including the following:

■ CAUTION: Do not store items of interest to children in

cabinets above a cooktop – Children climbing on the

cooktop to reach items could be seriously injured.

■ Proper Installation – Be sure your cooktop is properly

installed and grounded by a qualified technician.

■ Never Use Your Cooktop for Warming or Heating the

Room.

■ Do Not Leave Children Alone – Children should not be left

alone or unattended in area where cooktop is in use. They

should never be allowed to sit or stand on any part of the

cooktop.

■ Wear Proper Apparel – Loose-fitting or hanging garments

should never be worn while using the cooktop.

■ User Servicing – Do not repair or replace any part of the

cooktop unless specifically recommended in the manual. All

other servicing should be referred to a qualified technician.

■ Storage on Cooktop – Flammable materials should not be

stored near surface units.

■ Do Not Use Water on Grease Fires – Smother fire or flame

or use dry chemical or foam-type extinguisher.

■ Use Only Dry Potholders – Moist or damp potholders on

hot surfaces may result in burns from steam. Do not let

potholder touch hot heating elements. Do not use a towel

or other bulky cloth.

■ DO NOT TOUCH SURFACE UNITS OR AREAS NEAR

UNITS – Surface units may be hot even though they are

dark in color. Areas near surface units may become hot

enough to cause burns. During and after use, do not touch,

or let clothing or other flammable materials contact surface

units or areas near units until they have had sufficient time

to cool. Among those areas are the cooktop and surfaces

facing the cooktop.

■ Use Proper Pan Size – This cooktop is equipped with one

or more surface units of different size. Select utensils

having flat bottoms large enough to cover the surface unit

heating element. The use of undersized utensils will

expose a portion of the heating element to direct contact

and may result in ignition of clothing. Proper relationship of

utensil to burner will also improve efficiency.

■ Never Leave Surface Units Unattended at High Heat

Settings – Boilover causes smoking and greasy spillovers

that may ignite.

■ Glazed Cooking Utensils – Only certain types of glass,

glass/ceramic, ceramic, earthenware, or other glazed

utensils are suitable for cooktop service without breaking

due to the sudden change in temperature.

■ Utensil Handles Should Be Turned Inward and Not Extend

Over Adjacent Surface Units – To reduce the risk of burns,

ignition of flammable materials, and spillage due to

unintentional contact with the utensil, the handle of a

utensil should be positioned so that it is turned inward, and

does not extend over adjacent surface units.

■ Do Not Cook on Broken Cooktop – If cooktop should

break, cleaning solutions and spillovers may penetrate the

broken cooktop and create a risk of electric shock. Contact

a qualified technician immediately.

■ Clean Cooktop With Caution – If a wet sponge or cloth is

used to wipe spills on a hot cooking area, be careful to

avoid steam burn. Some cleaners can produce noxious

fumes if applied to a hot surface.

For units with ventilating hood –

■ Clean Ventilating Hoods Frequently – Grease should not

be allowed to accumulate on hood or filter.

■ When flaming foods under the hood, turn the fan on.

For units with coil elements –

■ Make Sure Reflector Pans or Drip Bowls Are in

Place – Absence of these pans or bowls during

cooking may subject wiring or components

underneath to damage.

■ Protective Liners – Do not use aluminum foil to line surface

unit drip bowls, except as suggested in the manual.

Improper installation of these liners may result in a risk of

electric shock, or fire.

■ Do Not Soak Removable Heating Elements - Heating

elements should never be immersed in water.

COOKTOP USE

This manual covers different models. The cooktop you have purchased may have some or all of the features listed.

30" (76.2 cm) Model JIC4430X

A. Left rear surface cooking area display

B. Surface cooking area off

C. Heat level display

D. Right rear surface cooking area display

E. Power on/off

F. Low settings

G. Sensor Boil

H. Left front surface cooking area display

I. Timer display

J. Timer (increase/decrease)

K. Heat level slider

L. Right front surface cooking area display

M. Left side bridge

N. Control lock

IGFE

36" (91.4 cm) Model JIC4536X

Induction Cooking

Induction cooking is quite different from traditional forms of

cooking. The heat is generated directly in the pan, keeping the

cooking surface cooler than a traditional element.

Induction cooking does not lose as much heat as traditional

forms because all the heat is created in the pan itself.

The cooktop heats up or cools down quickly after the controls

are set. It also stops heating when the pan is removed without

turning off the power.

Food spilled on the cooktop surface will not burn because the

glass is not heated. Induction cooking allows for immediate

cleaning after use because the heat is created in the pan.

Pan size, material (see “Cookware” section), and positioning is

very important to achieve maximum wattage.

The diameter of the pan’s base should be equal to the size of the

element.

If the pan is too small, the burner does not sense the pan and will

not activate.

Cooktop Controls

The touch-activated electronic controls offer a variety of heat

settings for optimal cooking results. When melting foods such as

chocolate or butter, the surface cooking area can be set to the

Melt function for minimal cooking power.

For maximum surface cooking power, all cooktop touch-

activated electronic controls can be set to Performance Boost

function when bringing liquids to a fast and rapid boil. Touch

BOOST to immediately reach the highest setting.

NOTE: This cooktop will also work with a 208V operation where

240V installation is not available.

A. Left rear surface cooking area display

B. Surface cooking area off

C. Center surface cooking area display

D. Heat level display

E. Right rear surface cooking area display

F. Power on/off

G. Low settings

H. Sensor Boil

I. Left front surface cooking area display

J. Timer display

K. Timer (increase/decrease)

L. Heat level slider

M. Right front surface cooking area display

N. Left side bridge

O. Right side bridge

P. Control lock

PONML

JIHGF

WARNING

Fire Hazard

Turn off all controls when done cooking.

Failure to do so can result in death or fire.

First use or after a power failure:

After connecting the cooktop to an electrical power supply or

after a power failure, the control panel will be locked. An indicator

light above the key icon will be on. To unlock the control panel,

press and hold CONTROL LOCK for 3 seconds. The indicator

light will turn off, and the cooktop is ready for use.

To Use

To Turn On the Cooktop:

1. Press POWER.

The indicator light above the Power keypad and a dash (“-”)

in each surface cooking area will light to indicate that each

surface cooking area is ready to be activated.

Inactivity for 1 minute after the main power has been turned

on will automatically turn off the power to the cooktop.

If a cooking function or the power slider are touched without

first selecting a surface cooking area, all dashes (one for each

zone) will flash and an invalid tone will sound 3 times.

To Turn On a Surface Cooking Area:

1. Touch directly on the display area for the surface cooking

area you want to use.

The current power level and indicator light will flash for

10 seconds then remain on.

Touching any other feature or the power slider stops the

flashing and information for the keypad that was touched will

be displayed.

When a surface cooking area is selected, the timer will also

turn on to show that it can now be set.

When a surface cooking area is left at the “0” power level for

1 minute, the surface cooking area will automatically turn off

and display only the middle dash without the indicator light.

2. Select a heat setting from 1 - 9 by touching/sliding on the

power slider. The heat setting will appear in the surface

cooking area display.

The power slider consists of 9 positions plus a “Boost”

position. When the user slides to 0, “0” will be displayed. The

surface cooking area will not turn on but remains active/

selected.

When a surface cooking area is left at the “0” power level for

1 minute, the zone will automatically turn off and display only

the middle dash without the indicator light.

Use the following chart as a guide when setting heat levels.

To Tur n Off:

1. Touch ON/OFF to turn off desired surface cooking area,

1 tone will sound when Off is pressed.

2. Touch POWER to turn off the cooktop when finished.

Hot Surface Indicator

An “H” will appear in the heat setting display as long as any

surface cooking area is too hot to touch, even after the surface

cooking area(s) is turned off.

Dual Size Surface Cooking Area

(on some models)

The dual size surface cooking area offers flexibility to cook using

different sizes of cookware. Single size can be used in the same

way as a regular surface cooking area. The dual size combines

inner and outer surface cooking areas and is recommended for

larger cookware, large quantities of food, and home canning.

The dual size surface cooking area contains two cooking areas.

If the size of the pan is the same as the single size surface

cooking area, the cooking area will work as a single size cooking

area.

If the pan is slightly larger than the single size cooking area, it

may activate only part of the dual size cooking area. This will

result in the burner being less efficient and will increase the

heating time.

If the size of the pan is the same as the dual size surface cooking

area, the dual size cooking area will activate automatically.

SETTING RECOMMENDED USE

9 - Boost

■ Bring liquid to a boil.

■ Start food cooking.

7 - 8

■ Quickly brown or sear food.

6 - 7 ■ Hold a rapid boil.

5 - 6

■ Fry or saute foods.

■ Cook soups, sauces and

gravies.

4 - 5

■ Maintain a slow boil.

■ Stew or steam food.

3 - 5 ■ Range of simmer levels for

simmering with or without a lid.

Melt

■ Melt chocolate or butter.

Simmer

■ Simmer sauces.

Keep Warm ■ Keep cooked foods warm.

Dual surface cooking

area

■ Home canning.

■ Large-diameter cookware.

■ Large quantities of food.

A. Heat setting display

B. Hot surface indicator “H”

A. Single size

B. Dual size

SETTING RECOMMENDED USE

Sensor Boil

The Sensor Boil function automatically selects the ideal power

level to boil water and has an audible beep when boiling is

reached. Sensor Boil is available only on one surface cooking

area. See the following illustrations for which surface cooking

area has Sensor Boil for your cooktop.

30” (76.2 cm) Model JIC4430X

36” (91.4 cm) Model JIC4536X

When using Sensor Boil:

■ Use only water at room temperature.

■ Do not add salt or any other ingredients to water until boiling

is reached.

■ Do not use a lid on a pot while using the Sensor Boil function.

■ Do not use the Sensor Boil function if the surface cooking

area is hot. “H” will appear in the display when the surface

cooking area is hot.

■ Do not change the power level or move the pot.

■ Fill the pot at least one-third of the way full with at least

4 cups (946 mL) of water but not up to the brim. Do not use

Sensor Boil with more than approximately 5 qt (5 L) for

36" (91.4 cm) models, or 7 qt (7 L) for 30" (76.2 cm) models.

■ For best results, use pots with a diameter between

9½" (24 cm) and 11" (28 cm) for 30" (76.2 cm) models. Use

pots with a diameter between 6½" (17 cm) and 7½" (19 cm)

for 36" (91.4 cm) models.

■ Do not use pressure cookers.

■ The quality of the cookware being used may affect the

performance of the Sensor Boil function.

To Use:

To Tur n On:

1. Check that the surface cooking area with available Sensor

Boil has been selected.

2. Put the pot on the selected surface cooking area for sensor

boiling.

3. Touch SENSOR BOIL. “A” will appear in the display, and the

indicator light next to Sensor Boil will light.

When the boiling point is reached, the cooktop will beep

3 times at regular intervals. After the second set of beeps, a

minute counter will start counting the boiling time

automatically. After the third set of beeps, the cooktop will

automatically switch to a lower power level suitable to

maintain the boil.

To Tur n Off:

Sensor Boil can be turned off in 3 different ways:

1. Use the power slider to set to a heat level.

2. Touch the surface cooking area OFF keypad.

3. Select a different cooking function.

NOTE: The cooktop manages the Sensor Boil and Performance

Boost functions automatically. In some cases, it may not be able

to use the Sensor Boil and Performance Boost functions

simultaneously.

Low Settings

The Low Settings function can be used with all surface cooking

areas. Low Settings can be used on more than 1 surface cooking

area at a time.

The Low Settings function allows you to select the Simmer, Melt

or Keep Warm functions for a specific surface cooking area.

To Use

To Tur n On:

1. Check that a surface cooking area has been selected.

2. Touch LOW SETTINGS. “A” will appear in the display for the

surface cooking area selected.

3. Press LOW SETTINGS until an indicator light next to the

desired function is lit.

The timer remains visible and can be set if desired.

To Tur n Off:

Low Settings can be turned off in 3 different ways:

1. Use the power slider to set to a heat level.

2. Touch the surface cooking area OFF keypad.

3. Select a different cooking function.

A. Surface cooking area with available Sensor Boil

Simmer

The Simmer function can be used with all surface cooking areas.

Simmer can be used on more than 1 surface cooking area at a

time.

To Use:

To Tur n On:

1. Check that a surface cooking area has been selected.

2. Touch SIMMER. “A” will appear in the display, and the

indicator light next to Simmer will light.

The timer remains visible and can be set if desired.

To Tur n Off:

Simmer can be turned off in 3 different ways:

1. Use the power slider to set to a heat level.

2. Touch the surface cooking area OFF keypad.

3. Select a different cooking function.

Melt

The Melt + Hold function can be used with all surface cooking

areas. Melt + Hold can be used on more than 1 surface cooking

area at a time.

To Use

To Tur n On:

1. Check that a surface cooking area has been selected.

2. Touch MELT + HOLD. “A” will appear in the display, and the

indicator light next to Melt + Hold will light.

The timer remains visible and can be set if desired.

To Tur n Off:

Melt + Hold can be turned off in 3 different ways:

1. Use the power slider to set to a heat level.

2. Touch the surface cooking area OFF keypad.

3. Select a different cooking function.

Keep Warm

The Keep Warm function can be used with all surface cooking

areas. Keep Warm can be used on more than 1 surface cooking

area at a time. Keep warm is not recommended for heating cold

foods.

To Use

To Tur n On:

1. Check that a surface cooking area has been selected.

2. Touch KEEP WARM. “A” will appear in the display, and the

indicator light next to Keep Warm will light.

The timer remains visible and can be set if desired.

To Tur n Off:

Keep Warm can be turned off in 3 different ways:

1. Use the power slider to set to a heat level.

2. Touch the surface cooking area OFF keypad.

3. Select a different cooking function.

Bridge

(on some models)

The Bridge function can be activated when surface cooking areas

are on or when they are off. The Bridge function allows you to use

2 cooking zones as an extra-large cooking zone.

To Turn On a Bridge:

1. Touch the desired Bridge keypad (left side bridge or right side

bridge).

The indicator light above the Bridge keypad will light. The

heat setting levels for the 2 surface cooking areas will default

to “0” and can be set from a minimum of “1” to a maximum of

“9.” Any timers that may be running for the 2 surface cooking

areas will turn off, and 2 dashes “--” will appear in the timer

display.

2. Slide a finger on the Heat Level Slider to change the power

level up or down.

The selected heat level will show in the heat level display for

each surface cooking area using the bridge.

A. Left side bridge

B. Right side bridge

WARNING

Food Poisoning Hazard

Do not let food sit for more than one hour before or

after cooking.

Doing so can result in food poisoning or sickness.

To Turn Off a Bridge:

1. Touch the Bridge keypad for the zone being used (left side

bridge or right side bridge).

The surface cooking areas will resume operation as 2

separate areas.

NOTE: Performance Boost cannot be used on the same

elements in combination when the Bridge function.

Pan Detection

If the system cannot recognize the pan, or if the pan has been

removed from the surface cooking area, the “replace pan”

animation appears in the cooking area display as a reminder. See

the following illustration.

If the pan is not placed within 30 seconds, the zone(s) will switch

Off.

If a Timer is running when a pan is removed, the countdown will

continue.

Control Lock

The Control Lock avoids unintended use of the surface cooking

areas.

If Control Lock is activated when power to the cooktop is off, the

cooktop is locked out, and the surface cooking areas cannot be

turned on by the cooktop touch controls.

If Control Lock is activated when power to the cooktop is on, all

keypads are locked out except for the Power and On/Off

keypads.

To Lock Cooktop:

Touch and hold the CONTROL LOCK keypad for 3 seconds. After

3 seconds, a tone will sound and the indicator light above the

Control Lock keypad will light, indicating that the cooktop

controls are in the lockout position.

If the cooktop is in use when Control Lock is activated, cooking

will proceed as normal and any timers that have been set will

continue their countdown.

To Unlock Cooktop:

Touch and hold the CONTROL LOCK keypad for 3 seconds.

Performance Boost Function

This function allows you to increase the heat setting level above

the maximum heat setting 9 for 10 minutes or less.

NOTE: Performance Boost is not available when the Bridge

function is activated.

30” (76.2 cm) Model JIC4430X

Performance Boost function is available on only 1 surface

cooking area at a time within a zone. If you attempt to use

another surface cooking area in the same zone, “P” and “9” will

briefly flash in the display before returning to heat setting level 9.

The surface cooking area that was set to the Performance boost

function will automatically reset to heat setting level 9. See the

following illustrations for zones.

36” (91.4 cm) Model JIC4536X

Performance Boost function is available on all surface cooking

areas at the same time within a zone. See the following

illustrations for zones.

Zone 1 Zone 2

A. Surface cooking

area 1

B. Surface cooking

area 2

C. Surface cooking area 3

D. Surface cooking area 4

Zone 1 Zone 2 Zone 3

A. Surface cooking

area 1

B. Surface cooking

area 2

C. Surface cooking

area 3, dual

element with

5000W

performance

boost

D. Surface cooking

area 4

E. Surface cooking

area 5

To Use:

1. Check that a surface cooking area has been selected.

2. Touch BOOST. “P” will appear in the display.

3. Touch BOOST keypad when finished. The “P” will no longer

be visible in the display, and the Performance boost function

will no longer be active. The surface cooking area turns back

to heat setting level 9.

NOTE: The Performance boost function may automatically

deactivate to keep the internal electronic components of the

cooktop from becoming too hot.

Timer

Use the cooking timer to set times up to 90 minutes. The timer is

independent of any other control settings. There is a separate

timer for each cooking zone.

To Use:

1. Select the desired cooking zone.

2. Touch the TIME keypad. “01” will appear in the timer display.

3. Touch the “>” key to increase the time in 1-minute

increments.

Touch the “<” key to decrease the time in 1-minute

increments.

4. The timer will start to count down after a few seconds.

To change the time, touch the time “>” or “<” keypads.

5. When the countdown is finished,”00” flashes and a tone will

sound.

NOTE: When the power is restored after an interruption, the timer

will no longer be running.

Tones

Tones are audible signals, indicating the following:

One tone

■ Valid pad press

■ Slider is moved to “0” power level

■ Slider is moved to “Boost” power level

Two tones

■ Invalid pad press

Three tones

■ End of Timer cycle

■ Boiling point is reached when using the Sensor Boil feature

Ceramic Glass

Cleaning off the induction cooktop before and after each use will

help keep it free from stains and provide the most even heating.

For more information, see “General Cleaning” section.

■ Avoid storing jars or cans above the cooktop. Dropping a

heavy or hard object onto the cooktop could crack the

cooktop.

■ To avoid damage to the cooktop, do not leave a hot lid on the

cooktop. As the cooktop cools, air can become trapped

between the lid and the cooktop, and the ceramic glass could

break when the lid is removed.

■ For foods containing sugar in any form, clean up all spills and

soils as soon as possible. Allow the cooktop to cool down

slightly. Then, while wearing oven mitts, remove the spills

while the surface is still warm. If sugary spills are allowed to

cool down, they can adhere to the cooktop and can cause

pitting and permanent marks.

■ To avoid scratches, do not slide cookware or bakeware

across the cooktop.

■ To avoid damage to the cooktop, do not allow objects that

could melt, such as plastic or aluminum foil, to touch any part

of the entire cooktop.

■ To avoid damage to the cooktop, do not use the cooktop as a

cutting board.

■ Use cookware about the same size as the surface cooking

area. Cookware should not extend more than ½" (1.3 cm)

outside the area.

■ Use flat-bottomed cookware for best heat conduction and

energy efficiency. Cookware with rounded, warped, ribbed or

dented bottoms could cause uneven heating and poor

cooking results.

■ Determine flatness by placing the straight edge of a ruler

across the bottom of the cookware. While you rotate the ruler,

no space or light should be visible between it and the

cookware.

■ Make sure the bottoms of pots and pans are clean and dry

before using them. Residue and water can leave deposits

when heated.

Cookware

Only ferromagnetic pans can be used for induction cooking.

Ferromagnetic materials include:

■ Enameled steel

■ Cast iron

■ Stainless steel designed for induction cooking

Non-ferromagnetic materials include:

These types of pans will not work with induction cooking.

■ Stainless steel

■ Glass

■ Ceramic

■ Copper or aluminum pans

To find out whether your pans can be used with an induction

cooktop, flip the pan over, hold a magnet to the bottom of the

pan, and see whether it sticks. If the magnet sticks to the bottom

of the pan, the pan is ferromagnetic and can be used for

induction cooking.

A. Surface cooking area

B. Cookware/canner

C. ½" (1.3 cm) Maximum overhang

The number on the surface cooking area heat setting display will

flash if no pan is placed on the surface cooking area, or the pan is

not made of the right material, or it is not the right size. It will stop

flashing once a suitable pan is placed on the surface cooking

area. If you take longer than 90 seconds to place the correct pan

on the surface cooking area, the surface cooking area will turn

off.

Ideal cookware should have a flat bottom, straight sides and a

well-fitting lid, and the material should be of medium-to-heavy

thickness.

Choose the correct pan size for each surface cooking area. The

diameter of the pan’s base should correspond to the size of the

surface cooking area.

NOTE: Cookware manufacturers often give the diameter across

the top of the pan. This is usually larger than the diameter of the

base.

Pans with rough finishes may scratch the cooktop.

COOKTOP CARE

General Cleaning

IMPORTANT: Before cleaning, make sure all controls are off and

the cooktop is cool. Always follow label instructions on cleaning

products.

Soap, water and a soft cloth or sponge are suggested first unless

otherwise noted.

CERAMIC GLASS

To avoid damage, do not use steel wool, abrasive powder

cleansers, chlorine bleach, rust remover or ammonia.

Cleaning Method:

Always wipe with a clean, wet cloth or sponge and dry thoroughly

to avoid streaking and staining.

Cooktop Cleaner is recommended for regular use to help avoid

scratches, pitting and abrasions, and to condition the cooktop. It

may be ordered as an accessory. See “Assistance or Service”

section to order.

A Cooktop Scraper is also recommended for stubborn soils, and

can be ordered as an accessory. See “Assistance or Service”

section to order. The Cooktop Scraper uses razor blades. Store

razor blades out of the reach of children.

Light to moderate soil

■ Paper towels or clean damp sponge.

■ Cooktop Cleaner and clean damp paper towel:

Clean as soon as cooktop has cooled down. Rub creme into

surface with a damp paper towel or soft cloth. Continue

rubbing until white film disappears.

Sugary spills (jellies, candy, syrup)

■ Cooktop Scraper:

Clean while the cooktop is still warm. You may want to wear

oven mitts while cleaning the cooktop.

Heavy soil, dark streaks, specks and discoloration

■ Cooktop Cleaner or nonabrasive cleanser:

Rub product into soil with a damp paper towel or soft cloth.

Continue rubbing until white film disappears.

Burned-on soil

■ Cooktop Cleaner and Cooktop Scraper:

Rub creme into soil with damp paper towel. Hold scraper as

flat as possible on surface and then scrape. Repeat for

stubborn spots. Polish entire cooktop with creme and paper

towel.

Tiny scratches and abrasions

■ Cooktop Cleaner:

Rub creme into surface with a damp paper towel or soft

cloth. Continue rubbing until white film disappears. Scratches

and abrasions do not affect cooking performance and after

many cleanings become less noticeable.

TROUBLESHOOTING

Try the solutions suggested here first in order to avoid the cost of an unnecessary service call.

Nothing will operate

■ Is the cooktop wired properly? See the Installation

Instructions for more information.

■ Has a household fuse blown, or has a circuit breaker

tripped? Replace the fuse or reset the circuit breaker. If the

problem continues, call an electrician.

Cooktop will not operate

■ Is the cooktop control set correctly? Touch the display area

on the control panel to select a cooking surface before

selecting a function.

■ Is the “Control Lock” Cooktop Lockout set? See “Control

Lock” section.

■ Has the cooktop turned off by itself? The power off key

was unintentionally touched. Press power key again. Reset

the cooktop.

Excessive heat around cookware on cooktop

■ Is the cookware the proper size? Use cookware about the

same size as the surface cooking area. Cookware should not

extend more than ½" (1.3 cm) outside the cooking area.

Cooktop cooking results not what expected

■ Is the proper cookware being used? See “Cookware”

section.

■ Is the cooktop control set to the proper heat level? See

“Cooktop Controls” section.

■ Is the cooktop level? Level the cooktop. See the Installation

Instructions.

Display shows messages

■ Is the display flashing when you place a saucepan on an

induction surface cooking area? Check that the saucepan

is electromagnetic. Check that the diameter of the saucepan

is large enough. Center the saucepan on the surface cooking

area. Allow the saucepan to cool down in the event that it has

become hot when used. Switch the surface cooking area off,

then on again. If the display still does not light up, turn power

off at the circuit breaker. Wait 20 seconds and turn power

back on.

■ Is the Performance boost function display flashing and

switching off? The Performance boost function operates the

surface cooking area with the most power. During long

cooking times, it is possible that the function will switch the

surface cooking area off to keep the cooktop from

overheating. You can continue to use the cooktop if the

display is not flashing.

■ Is the display flashing “Er” and numbers? If an “Er” and a

series of numbers appear in the display panel, turn power off

at the circuit breaker. Turn on again. If problem continues, call

customer service. See “Assistance or Service” section.

■ Is the display flashing “F” or “C” and numbers? If “F” or

“C” and a number are alternately flashing on the display, refer

to the following table for possible solutions.

Operational cooktop sounds

■ Is there a low humming? This occurs when cooking at high

power. The cause of this is the amount of energy that is

transmitted from the appliance to the cookware. This sound

will quiet or go away when the power is turned down.

■ Is there a crackling? This sound occurs when cookware is

used that consists of different materials. The noise is caused

by vibrations in the joint faces between the different layers. It

may change depending on the amount and type of food

being cooked.

■ Is there a fan noise? The electronics require a controlled

temperature in order to function reliably. The cooktop is fitted

with a fan that runs at various speeds according to the

temperature detected. The fan may also continue to run even

after the cooktop has been switched off, if the temperature it

detects is too high.

Error

Code

Error Solution

Cooktop

has

turned off

and is

beeping

every

10 sec.

An object, liquids

or soils are

putting pressure

on the control

panel.

Thoroughly wipe or remove

any object on touch keys.

F42, F43 The power

voltage is too low

or too high.

Turn off the cooktop. Wait

5 seconds, then turn it back

on. If this continues, contact a

qualified electrician.

C81, C82,

C83

The surface

cooking area has

overheated.

The surface cooking area

automatic shutoff was

activated. Wait 5 minutes for it

to cool down, then turn it back

on. Turn off oven if it is running

a self cleaning cycle.

F12, F21,

F25, F36,

F37, F40,

F47, F56,

F58, 560,

F61, F62,

F63, F64

Call customer service. See the

“Assistance or Service”

section.

ASSISTANCE OR SERVICE

Before calling for assistance or service, please check

“Troubleshooting.” It may save you the cost of a service call. If

you still need help, follow the instructions below.

When calling, please know the purchase date and the complete

model and serial number of your appliance. This information will

help us to better respond to your request.

In the U.S.A.

If the problem is not due to one of the items listed in the

“Troubleshooting” section…

Call the dealer from whom your appliance was purchased, or call

Jenn-Air at 1-800-JENNAIR (1-800-536-6247) to locate an

authorized service company. When calling, please know the

purchase date and the complete model and serial number of your

appliance. Be sure to retain proof of purchase to verify warranty

status.

If the dealer or service company cannot resolve your problem,

write to:

Jenn-Air Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

Web address: www.jennair.com

Or call: 1-800-JENNAIR (1-800-536-6247)

U.S. customers using TTY for deaf, hearing impaired or speech

impaired, call: 1-800-688-2080.

NOTE: When writing or calling about a service problem, please

include the following information:

1. Your name, address and daytime telephone number.

2. Appliance model number and serial number.

3. Name and address of your dealer or servicer.

4. A clear description of the problem you are having.

5. Proof of purchase (sales receipt).

User’s guides, service manuals and parts information are

available from Jenn-Air Brand Home Appliances, Customer

eXperience Center.

Accessories

Cooktop Bracket Adhesive Kit

(for marble countertop installations only)

Order Part Number W10310006

Cooktop Cleaner

(ceramic glass models)

Order Part Number 31464

Cooktop Protectant

(ceramic glass models)

Order Part Number 31463

Cooktop Scraper

(ceramic glass models)

Order Part Number WA906B

All-Purpose Appliance Cleaner

Order Part Number 31662

In Canada

If the problem is not due to one of the items listed in the

“Troubleshooting” section…

Call the dealer from whom your appliance was purchased, or call

Jenn-Air at 1-800-807-6777 to locate an authorized service

company. When calling, please know the purchase date and the

complete model and serial number of your appliance. Be sure to

retain proof of purchase to verify warranty status.

If the dealer or service company cannot resolve your problem,

write to:

Jenn-Air Brand Home Appliances

Customer eXperience Centre

200 - 6750 Century Ave.

Mississauga, ON L5N 0B7

Web address: www.jennair.ca

Or call: 1-800-807-6777.

NOTE: When writing or calling about a service problem, please

include the following information:

1. Your name, address and daytime telephone number.

2. Appliance model number and serial number.

3. Name and address of your dealer or servicer.

4. A clear description of the problem you are having.

5. Proof of purchase (sales receipt).

User’s guides, service manuals and parts information are

available from Jenn-Air Brand Home Appliances, Customer

eXperience Centre.

JENN-AIR

COOKING APPLIANCE WARRANTY

LIMITED WARRANTY

For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or

furnished with the product, Jenn-Air brand of Whirlpool Corporation or Whirlpool Canada LP (hereafter “Jenn-Air”) will pay for factory

specified parts and repair labor to correct defects in materials or workmanship. Service must be provided by a Jenn-Air designated

service company. This limited warranty is valid only in the United States or Canada and applies only when the major appliance is used

in the country in which it was purchased. Outside the 50 United States and Canada, this limited warranty does not apply. Proof of

original purchase date is required to obtain service under this limited warranty.

SECOND THROUGH FIFTH YEAR LIMITED WARRANTY ON CERTAIN COMPONENT PARTS

In the second through fifth years from the date of purchase, when this appliance is operated and maintained according to instructions

attached to or furnished with the product, Jenn-Air will pay for factory specified parts for the following components (if applicable to the

product) if defective in materials or workmanship:

ITEMS EXCLUDED FROM WARRANTY

This limited warranty does not cover:

1. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or

repair house fuses, or to correct house wiring or plumbing.

2. Service calls to repair or replace appliance light bulbs, air filters or water filters. Consumable parts are excluded from warranty

coverage.

3. Repairs when your major appliance is used for other than normal, single-family household use or when it is used in a manner that is

contrary to published user or operator instructions and/or installation instructions.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in

accordance with electrical or plumbing codes, or use of consumables or cleaning products not approved by Jenn-Air.

5. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage

results from defects in materials or workmanship and is reported to Jenn-Air within 30 days from the date of purchase.

6. Any food loss due to refrigerator or freezer product failures.

7. Costs associated with the removal from your home of your major appliance for repairs. This major appliance is designed to be

repaired in the home and only in-home service is covered by this warranty.

8. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

9. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an

authorized Jenn-Air servicer is not available.

10. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance

with published installation instructions.

11. Major appliances with original model/serial numbers that have been removed, altered or cannot be easily determined. This warranty

is void if the factory applied serial number has been altered or removed from your major appliance.

The cost of repair or replacement under these excluded circumstances shall be borne by the customer.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES

CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED

HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,

ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. JENN-AIR SHALL NOT BE LIABLE FOR INCIDENTAL

OR CONSEQUENTIAL DAMAGES. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF

INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES

YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE OR PROVINCE

TO PROVINCE.

If outside the 50 United States and Canada, contact your authorized Jenn-Air dealer to determine if another warranty applies.

If you need service, first see the “Troubleshooting” section of the Use & Care Guide. After checking “Troubleshooting,” you may find

additional help by checking the “Assistance or Service” section or by calling Jenn-Air. In the U.S.A., call 1-800-536-6247. In Canada,

call 1-800-807-6777. 6/09

Keep this book and your sales slip together for future

reference. You must provide proof of purchase or installation

date for in-warranty service.

Write down the following information about your major appliance

to better help you obtain assistance or service if you ever need it.

You will need to know your complete model number and serial

number. You can find this information on the model and serial

number label located on the product.

Dealer name____________________________________________________

Address ________________________________________________________

Phone number__________________________________________________

Model number __________________________________________________

Serial number __________________________________________________

Purchase date __________________________________________________

■ Electric element

■ Touch Pad and microprocessor

■ Glass ceramic cooktop: if due to thermal breakage

■ Electronic controls

■ Magnetron tube

■ Sealed gas burners

SÉCURITÉ DE LA TABLE DE CUISSON

Risque possible de décès ou de blessure grave si vous ne

suivez pas immédiatement les instructions.

Risque possible de décès ou de blessure grave si vous

ne suivez pas les instructions.

Tous les messages de sécurité vous diront quel est le danger potentiel et vous disent comment réduire le risque de blessure et

ce qui peut se produire en cas de non-respect des instructions.

Votre sécurité et celle des autres est très importante.

Nous donnons de nombreux messages de sécurité importants dans ce manuel et sur votre appareil ménager. Assurez-vous de

toujours lire tous les messages de sécurité et de vous y conformer.

AVERTISSEMENT

DANGER

Voici le symbole d’alerte de sécurité.

Ce symbole d’alerte de sécurité vous signale les dangers potentiels de décès et de blessures graves à vous

et à d’autres.

Tous les messages de sécurité suivront le symbole d’alerte de sécurité et le mot “DANGER” ou

“AVERTISSEMENT”. Ces mots signifient :

IMPORTANTES INSTRUCTIONS DE SÉCURITÉ

CONSERVEZ CES INSTRUCTIONS

AVERTISSEMENT : Pour réduire le risque d'incendie, de

choc électrique, de blessures ou de dommages lors de

l'utilisation de la table de cuisson, observer les précautions

élémentaires suivantes, y compris ce qui suit :

■ MISE EN GARDE : Ne pas remiser dans les armoires

au-dessus d'une table de cuisson, des articles que des

enfants pourraient vouloir atteindre. Les enfants pourraient

se brûler ou se blesser en grimpant sur la table de cuisson.

■ Installation appropriée – S’assurer que la table de cuisson

est correctement installée et reliée à la terre par un

technicien qualifié.

■ Ne jamais utiliser la table de cuisson pour réchauffer ou

chauffer la pièce.

■ Ne pas laisser les enfants seuls – Les enfants ne doivent

pas être laissés seuls ou sans surveillance dans la pièce

où la table de cuisson est en service. Ne jamais laisser les

enfants s’asseoir ou se tenir sur une partie quelconque de

la table de cuisson.

■ Porter des vêtements appropriés – Des vêtements amples

ou détachés ne doivent jamais être portés pendant

l’utilisation de la table de cuisson.

■ Entretien par l’utilisateur – Ne pas réparer ou remplacer

toute pièce de la table de cuisson si ce n’est pas

spécifiquement recommandé dans le manuel. Toute autre

opération d’entretien ou de réparation doit être confiée à un

technicien qualifié.

■ Remisage sur la table de cuisson – Des matériaux

inflammables ne doivent pas être remisés près des

éléments à la surface.

■ Ne pas utiliser d’eau sur un feu de graisse – Étouffer le feu

ou la flamme ou utiliser un extincteur à produits chimiques

secs ou à mousse.

■ N’utiliser que des mitaines de four sèches – Des mitaines

de four mouillées ou humides sur des surfaces chaudes

peuvent provoquer des brûlures provenant de la vapeur.

Ne pas laisser les mitaines de four toucher les éléments

chauffants. Ne pas utiliser une serviette ou autre tissu

épais.

■ NE PAS TOUCHER LES ÉLÉMENTS À LA SURFACE OU

L’ESPACE PRÈS DES ÉLÉMENTS – Les éléments de

surface peuvent être chauds même lorsqu’ils ont une teinte

foncée. Les endroits près des éléments à la surface

peuvent devenir assez chauds pour provoquer des

brûlures. Pendant et après l’utilisation, ne pas toucher les

éléments chauffants et ne pas laisser les vêtements ou

autres matériaux inflammables entrer en contact avec ces

éléments de surface ou les endroits près des éléments,

avant qu’ils soient suffisamment refroidis. Ces endroits

comprennent la table de cuisson et les surfaces près de la

table de la cuisson.

■ Utiliser des ustensiles de format approprié – La table de

cuisson est munie d’un ou de plusieurs éléments

chauffants de différentes grandeurs. Choisir les ustensiles

qui ont un fond plat assez grand pour couvrir l’élément

chauffant de la surface de cuisson. L’utilisation d’ustensiles

trop petits exposera une partie de l’élément chauffant, ce

qui peut provoquer l’inflammation des vêtements.

L’utilisation d’un récipient de format correct améliore

l’efficacité de la cuisson.

■ Ne jamais laisser les éléments de la table de cuisson sans

surveillance alors qu’ils chauffent à la puissance maximale

– Il pourrait en résulter une ébullition qui cause de la

fumée et des renversements de corps gras qui peuvent

s’enflammer.

■ Ustensiles de cuisson vitrifiés – Seulement certains types

d’ustensiles de verre, vitrocéramique, céramique, faïence

ou autres surfaces vitrifiées conviennent pour le service

sur une table de cuisson, sans bris attribuables aux

changements soudains de température.

■ Les poignées des ustensiles doivent être tournées vers

l’intérieur et non vers le dessus des éléments adjacents –

Pour réduire les risques de brûlures, d’inflammation de

produits combustibles et de renversements dus à

l’entrechoquement non intentionnel des ustensiles, la

poignée d’un ustensile doit être positionnée de sorte qu’elle

est tournée vers l’intérieur et non au-dessus des éléments

de surface adjacents.

■ Ne pas faire cuire sur une table de cuisson endommagée –

Si la table de cuisson est brisée, les solutions de

nettoyage et les renversements peuvent pénétrer dans la

table brisée et créer le risque d’un choc électrique.

Contacter immédiatement un technicien qualifié.

■ Nettoyer la table de cuisson avec prudence – Si une

éponge ou un chiffon mouillé est utilisé pour essuyer les

renversements sur une surface de cuisson chaude, éviter

les brûlures causées par la vapeur chaude. Certains

nettoyants peuvent produire des émanations désagréables

lorsqu’ils sont utilisés sur une surface chaude.

Pour les appareils avec hotte de ventilation –

■ Nettoyer les hottes de ventilation fréquemment – La

graisse ne doit pas s’accumuler sur la hotte ou le filtre.

■ Lorsque vous flambez des aliments sous la hotte, mettre le

ventilateur en marche.

Pour les appareils à éléments en spirale –

■ S’assurer que les cuvettes de propreté sont en place –

L’absence de ces cuvettes au cours de la cuisson peut

causer des dommages aux fils ou aux composants en

dessous des éléments.

■ Garnissages protecteurs – Ne pas recouvrir les cuvettes

de papier d’aluminium sauf tel que suggéré dans le

manuel. L’installation incorrecte de papier d’aluminium ou

autre matériau peut causer un risque de choc électrique ou

d’incendie.

■ Ne pas tremper les éléments de chauffage amovibles –

Les éléments de chauffage ne doivent jamais être

immergés dans l'eau.

Cette table de cuisson à induction génère et utilise une énergie de fréquence ISM qui chauffe l’ustensile de cuisson à l’aide d’un champ

électromagnétique. Elle a été testée et déclarée conforme à la section 18 du règlement FCC pour l’équipement ISM. Cette table de

cuisson à induction satisfait aux exigences du règlement FCC pour la minimisation des interférences avec d’autres dispositifs

résidentiels.

Cette table de cuisson à induction peut causer des interférences pour la réception de la télévision et de la radio. En cas d’interférence,

l’utilisateur doit essayer d’y remédier en prenant une ou plusieurs des mesures suivantes :

Changer l’orientation de l’antenne de réception de la radio ou de la télévision.

Éloigner la table de cuisson du récepteur.

Brancher le récepteur dans une prise différente.

Il incombe à l’utilisateur de corriger toute interférence.

REMARQUE : Les personnes utilisant un pacemaker ou un dispositif médical similaire doivent prendre leurs précautions lorsqu’elles se

trouvent à proximité d’une table de cuisson à induction allumée. Le champ électromagnétique peut affecter le fonctionnement du

pacemaker ou de tout dispositif similaire. Consultez votre médecin ou le fabricant du pacemaker ou du dispositif médical pour obtenir

des informations supplémentaires à propos de ses effets en présence de champs magnétiques émis par la table de cuisson à

induction.

UTILISATION DE LA TABLE DE CUISSON

Ce manuel couvre différents modèles. La table de cuisson que vous avez achetée peut comporter toutes les caractéristiques

énumérées ou seulement certaines d'entre elles.

Modèle JIC4430X de 30" (76,2 cm)

A. Affichage de la surface de cuisson

arrière gauche

B. Arrêt surface de cuisson

C. Affichage du niveau de chaleur

D. Affichage de la surface de cuisson

arrière droite

E. Mise sous tension-Marche/Arrêt

F. Réglages de chaleur réduite

G. Ébullition avec capteur

H. Affichage de la surface de cuisson avant

gauche

I. Affichage de la minuterie

J. Minuterie (augmentation/diminution)

K. Curseur du niveau de chaleur

L. Affichage de la surface de cuisson avant

droite

M. Liaison de gauche

N. Verrouillage des commandes

IGFE

Modèle JIC4536X de 36" (91,4 cm)

Cuisson par induction

La cuisson par induction est très différente des formes de

cuisson traditionnelles. La chaleur est générée directement dans

l’ustensile de cuisson; la surface de cuisson demeure plus froide

qu’un élément traditionnel.

Avec la cuisson par induction, il y a une moindre déperdition de

chaleur qu’avec les formes de cuisson traditionnelles du fait que

la chaleur est générée dans l’ustensile lui-même.

La table de cuisson chauffe ou se refroidit rapidement après le

réglage des commandes. Elle cesse également de chauffer

lorsqu’on retire l’ustensile sans avoir à éteindre l’appareil.

Les aliments renversés sur la surface de la table de cuisson ne

brûlent pas car le verre n’est pas chauffé. La cuisson par

induction permet un nettoyage immédiat après utilisation car la

chaleur est générée dans l’ustensile.

La taille, le matériau (voir la section “Ustensiles de cuisson”) et le

positionnement du plat sont très importants pour atteindre une

puissance maximale.

Le diamètre de la base du plat doit être identique à la taille de

l’élément.

Si l’ustensile est trop petit, le brûleur ne le détecte pas et reste

éteint.

Commandes de la table de cuisson

Les commandes électroniques tactiles offrent une grande variété

de réglages de chaleur pour des résultats de cuisson optimaux.

Lorsqu’on fait fondre des aliments comme du chocolat ou du

beurre, la surface de cuisson peut être réglée sur la fonction Melt

(faire fondre) pour une consommation minimale de l'énergie de

cuisson.

Pour une puissance maximale de la zone de cuisson, toutes les

commandes électroniques tactiles de la table de cuisson peuvent

être réglées à la fonction Optimisation de rendement pour porter

rapidement un liquide à ébullition. Appuyer sur BOOST

(optimisation) pour atteindre immédiatement le réglage le plus

élevé.

A. Affichage de la surface de cuisson arrière gauche

B. Arrêt surface de cuisson

C. Affichage de la surface de cuisson centrale

D. Affichage du niveau de chaleur

E. Affichage de la surface de cuisson arrière droite

F. Mise sous tension-Marche/Arrêt

G. Réglages de chaleur réduite

H. Ébullition avec capteur

I. Affichage de la surface de cuisson avant gauche

J. Affichage de la minuterie

K. Minuterie (augmentation/diminution)

L. Curseur du niveau de chaleur

M. Affichage de la surface de

cuisson avant droite

N. Liaison de gauche

O. Liaison de droite

P. Verrouillage des commandes

PONML

JIHGF

Risque d'incendie

Fermer tous les réglages lorsque la cuisson est

terminée.

Le non-respect de cette instruction peut causer un

décès ou un incendie.

AVERTISSEMENT

REMARQUE : Cette table de cuisson fonctionne également avec

un courant de 208 volts lorsque l'installation ne fonctionne pas

sur du 240 volts.

Première utilisation ou après une panne de courant :

Après avoir raccordé la table de cuisson à une source

d'alimentation électrique ou après une panne de courant, le

tableau de commande est verrouillé. Un témoin lumineux

s'allume au-dessus de l'icône de clé. Pour déverrouiller le tableau

de commande, appuyer sur CONTROL LOCK (verrouillage des

commandes) pendant 3 secondes. Le témoin lumineux s'éteint et

la table de cuisson est prête à être utilisée.

Utilisation

Pour allumer la table de cuisson :

1. Appuyer sur POWER (mise sous tension).

Le témoin lumineux situé au-dessus de la touche Power

(mise sous tension) ainsi qu'un tiret (“-”) pour chaque surface

de cuisson s'allume pour indiquer que toutes les surfaces de

cuisson sont prêtes à être activées.

Si l'on ne fait rien pendant la minute qui suit l'activation de

l'alimentation principale, l'alimentation de la table de cuisson

est automatiquement interrompue.

Si l'on touche une fonction de cuisson ou le curseur

d'alimentation sans sélectionner de surface de cuisson au

préalable, tous les tirets (un par zone) clignotent et un signal

sonore d'action invalide retentit 3 fois.

Pour activer une surface de cuisson :

1. Toucher directement la zone d'affichage correspondant à la

surface de cuisson que l'on souhaite utiliser.

Le niveau de puissance actuel et le témoin lumineux

clignotent pendant 10 secondes, puis restent allumés.

Si l'on touche une autre caractéristique ou le curseur

d'alimentation, le clignotement cesse. De plus, les

informations concernant la touche qui a été touchée

s'affichent.

Si l'on sélectionne une surface de cuisson, la minuterie

s'allume également pour indiquer qu'elle peut maintenant

être réglée.

Si une surface de cuisson reste au niveau de puissance “0”

pendant 1 minute, la surface de cuisson s'éteint

automatiquement et seul le tiret du milieu s'affiche, sans

témoin lumineux.

2. Sélectionner un niveau de chaleur de 1 à 9 en touchant/

faisant glisser le curseur d'alimentation. Le réglage de

chaleur apparaît sur l'afficheur de la surface de cuisson.

Le curseur d'alimentation présente 9 positions, ainsi qu'une

position “Boost” (optimisation). Lorsque l'utilisateur fait

glisser le curseur à 0, “0” s'affiche. La surface de cuisson ne

s'allume pas mais reste active/sélectionnée.

Lorsqu'une surface de cuisson reste au niveau de puissance

“0” pendant 1 minute, la zone s'éteint automatiquement et

seul le tiret du milieu s'affiche, sans témoin lumineux.

Utiliser le tableau suivant comme guide lors du réglage des

niveaux de chaleur.

Désactivation :

1. Appuyer sur ON/OFF (marche/arrêt) pour éteindre la surface

de cuisson désirée.

Un signal sonore retentit lorsqu'on appuie sur Off (arrêt).

2. Appuyer sur POWER (mise sous tension) pour éteindre la

table de cuisson lorsqu'on a terminé.

Indicateur de surface chaude

Un “H” apparaît sur l’afficheur du réglage de chaleur tant qu’une

surface de cuisson est trop chaude pour être touchée, même une

fois que la ou les surfaces sont éteintes.

RÉGLAGE UTILISATION RECOMMANDÉE

9 - Boost

(optimisation)

■ Porter un liquide à ébullition.

■ Démarrer la cuisson des

aliments.

7 - 8

■ Brunir ou saisir rapidement les

aliments.

6 - 7

■ Maintenir une ébullition rapide.

5 - 6

■ Faire frire ou sauter les

aliments.

■ Faire cuire les soupes et les

sauces.

4 - 5

■ Maintenir une ébullition lente.

■ Faire mijoter ou étuver les

aliments.

3 - 5

■ Différents niveaux de mijotage

pour un mijotage avec ou sans

couvercle.

Faire fondre

■ Faire fondre le chocolat ou le

beurre.

Mijotage

■ Mijotage des sauces.

Maintien au chaud

■ Pour garder au chaud les

aliments cuits.

Surface de cuisson

double

■ Préparation de conserves à la

maison.

■ Ustensile de cuisson à grand

diamètre.

■ Grandes quantités de

nourriture

A. Afficheur du réglage de

chaleur

B. Témoin lumineux de surface

chaude “H”

Surface de cuisson à dimension double

(sur certains modèles)

La surface de cuisson à dimension double offre une flexibilité qui

permet d'utiliser des ustensiles de cuisson de différentes tailles.

La dimension simple peut être utilisée de la même manière

qu’une surface de cuisson ordinaire. La dimension double

combine les surfaces de cuisson interne et externe; elle est

recommandée pour les ustensiles de cuisson de plus grande

dimension, les grandes quantités d'aliments et pour la

préparation de conserves à la maison.

La surface de cuisson à dimension double comprend deux zones

de cuisson.

Si la taille de l’ustensile est identique à celle de la surface de

cuisson à dimension simple, la surface de cuisson fonctionne

comme une surface de cuisson à dimension simple.

Si l’ustensile est légèrement plus grand que la zone de cuisson à

dimension simple, il se peut que seule une partie de la zone de

cuisson à dimension double s’allume. Le brûleur sera alors moins

efficace et la durée de chauffage plus longue.

Si la taille de l’ustensile est identique à celle de la surface de

cuisson à dimension double, la surface de cuisson à dimension

double s’active automatiquement.

Ébullition avec capteur

La fonction d'ébullition avec capteur sélectionne

automatiquement le niveau de puissance idéal pour faire bouillir

de l'eau et est muni d'un signal sonore pour prévenir l'utilisateur

lorsque le point d'ébullition a été atteint. La fonction d'ébullition

avec capteur n'est disponible que pour une seule surface de

cuisson. Voir les illustrations suivantes pour déterminer quelle est

la surface de cuisson équipée de la fonction d'ébullition avec

capteur sur votre table de cuisson.

Modèle JIC4430X de 30" (76,2 cm)

Modèle JIC4536X de 36" (91,4 cm)

Lors de l'utilisation de la fonction d'ébullition

avec capteur :

■ Utiliser uniquement de l'eau à température ambiante.

■ Ne pas ajouter de sel ou d'autres ingrédients à l'eau que l'on

fait bouillir avant que le point d'ébullition ne soit atteint.

■ Ne pas couvrir la casserole lorsqu'on utilise la fonction

d'ébullition avec capteur.

■ Ne pas utiliser la fonction d'ébullition avec capteur si la

surface de cuisson est chaude. “H” apparaît sur l'affichage

lorsque la surface de cuisson est chaude.

■ Ne pas modifier le niveau de puissance ni déplacer la

casserole.

■ Remplir la casserole à au moins un tiers de sa capacité avec

au moins 4 tasses (946 mL) d'eau, mais ne jamais remplir

jusqu'au rebord du récipient. Ne pas utiliser la fonction

d'ébullition avec capteur avec plus d'environ 5 ptes (5 L) pour

les modèles de 36" (91,4 cm), ou 7 ptes (7 L) pour les

modèles de 30" (76,2 cm).

■ Pour de meilleurs résultats, utiliser des casseroles d'un

diamètre compris entre 9½" (24 cm) et 11" (28 cm) pour les

modèles de 30" (76,2 cm). Utiliser des casseroles d'un

diamètre compris entre 6½" (17 cm) et 7½" (19 cm) pour les

modèles de 36" (91,4 cm).

■ Ne pas utiliser d'autocuiseurs.

■ La qualité des ustensiles de cuisson utilisés peuvent affecter

la performance de la fonction d'ébullition avec capteur.

Utilisation :

Activation :

1. Vérifier que la surface de cuisson avec la fonction d'ébullition

disponible a été sélectionnée.

2. Placer la casserole sur la surface de cuisson sélectionnée

pour une ébullition avec capteur.

3. Appuyer sur SENSOR BOIL. “A” apparaît sur l'affichage et le

témoin lumineux situé à côté de Sensor Boil s'allume.

Lorsque le point d'ébullition a été atteint, le signal sonore de

la table de cuisson retentit 3 fois de suite à intervalles

réguliers. Après la deuxième série de signaux sonores, un

compte à rebours commence automatiquement à décompter

le temps d'ébullition, minute après minute. Après la troisième

série de signaux sonores, la table de cuisson passe

automatiquement à un niveau de puissance adapté pour

maintenir l'ébullition.

A. Dimension simple

B. Dimension double

A. Surface de cuisson avec fonction d'ébullition avec

capteur disponible

A. Surface de cuisson avec fonction d'ébullition

avec capteur disponible

La page charge ...

Jenn-Air JIC4536XB Mode d'emploi

Marque: Jenn-Air

Modèle: JIC4536XB

Catégorie: Cuisinières

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Jenn-Air JIC4536XB User guide

Jenn-Air JIC4536XB Mode d'emploi

Jenn-Air JIC4536XB Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents