The WLS908 Wireless Panic Pendant is a device designed to transmit a
non-medical emergency signal from any location within the range of the
PC5132-900 Wireless Receiver (software version 2.0 or higher). Signals will
be transmitted whether the system is armed or not.
The pendant can be attached to a necklace or a belt clip. The unit is even
small and lightweight enough to be placed in a shirt pocket or tucked
inside a purse. The pendant is also water resistant.
Signals will not be transmitted if the pendant is not within the
range of the wireless receiver.
To activate an alarm, press and hold both
large outer buttons for two seconds.
Testing the pendant
The pendant should be tested on a weekly
basis along with the rest of your alarm system.
For full system testing instructions, please
consult your PC5010 Instruction manual. To
test the pendant:
1. Begin testing when your system is in the
ready state and the keypad Ready light is ON.
2. Press and hold the small middle button on
the pendant marked “Test” for two seconds.
Once the test has completed and the
pendant’s battery condition is normal, the
Ready will turn off for four to five seconds.
3. If the pendant’s battery is low, the keypad
Trouble light will turn ON and a series of
continuous keypad beeps will be heard.
NOTE: If a low battery condition is
detected, you must inform your installer
immediately to have the unit replaced.
©
1997, 2001 Digital Security Controls Ltd.
Printed in Canada 29001920 R1
WLS908
Wireless Panic Pendant
OPERATING INSTRUCTIONS
FCC COMPLIANCE STATEMENT
CAUTION: Changes or modifications not expressly approved by Digital Security Controls Ltd. could void your
authority to use this equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
n
Re-orient the receiving antenna.
n
Increase the separation between the equipment and receiver.
n
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
n
Consult the dealer or an experienced radio/television technician for help.
The user may find the following booklet prepared by the FCC useful: “How to Identify and Resolve Radio/
Television Interference Problems”. This booklet is available from the U.S. Government Printing Office, Washing-
ton D.C. 20402, Stock # 004-000-00345-4.
Digital Security Controls Ltd. 160 Washburn St., Lockport, NY 14094
This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1)
this device may not cause interference, and (2) this device must accept any interference, including interference that
may cause undesired operation of the device.
Ce dispositif satisfait aux exigences d’Industrie Canada, prescrites dans le document CNR-210. son utilisation est
autorisée seulement aux conditions suivantes: (1) il ne doit pas produire de brouillage et (2) l’utilisateur du
dispositif doit être prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de
compromettre le fonctionnement du dispositif.
If you have the PC5132 RS Wireless Receiver, software version 2.0, a
panic alarm will occur when the test button is pressed. If you have
this receiver, you MUST call your monitoring station before pressing
the test button to alert them that you are testing the panic pendant.
LIMITED WARRANTY
Digital Security Controls Ltd. warrants that for a period of twelve months from the date of
purchase, the product shall be free of defect in materials and workmanship under normal use
and that in fulfilment of any breach of such warranty, Digital Security Controls Ltd. shall, at its
option, repair or replace the defective equipment upon return of the equipment to its repair
depot. This warranty applies only to defects in parts and workmanship and not to damage
incurred in shipping or handling, or damage due to causes beyond the control of Digital Security
Controls Ltd. such as lightning, excessive voltage, mechanical shock, water damage, or
damage arising out of abuse, alteration or improper application of the equipment.
The foregoing warranty shall apply only to the original buyer, and is and shall be in lieu of any
and all other warranties, whether expressed or implied and of all other obligations or liabilities on
the part of Digital Security Controls Ltd. This warranty contains the entire warranty. Digital
Security Controls Ltd. neither assumes, nor authorizes any other person purporting to act on its
behalf to modify or to change this warranty, nor to assume for it any other warranty or liability
concerning this product.
In no event shall Digital Security Controls Ltd. be liable for any direct, indirect or consequential
damages, loss of anticipated profits, loss of time or any other losses incurred by the buyer in
connection with the purchase, installation or operation or failure of this product.
WARNING: Digital Security Controls Ltd. recommends that the entire system be completely
tested on a regular basis. However, despite frequent testing, and due to, but not limited to,
criminal tampering or electrical disruption, it is possible for this product to fail to perform
as expected.
-
1
dans d''autres langues
- English: DSC WLS908 User manual
Documents connexes
-
DSC WS4939 Manuel utilisateur
-
DSC WLS909 Manuel utilisateur
-
-
-
-
-
DSC HS2ICNP Manuel utilisateur
-
-
-
DSC LCD5511 Manuel utilisateur
