Honeywell RTHL2510,RTHL2410 Le manuel du propriétaire

Taper
Le manuel du propriétaire

Ce manuel convient également à

69-2714EF-01
Quick Installation Guide
RTHL2510/RTHL2410 Series
Programmable Thermostat
69 -2714EF 01 ii
Identify System Type
This thermostat is compatible with the following systems:
Gas, oil or electric furnace
Central air conditioner
Hot water system with or without pump
Millivolt system
Central heating and cooling system
Heat pump without auxiliary/backup heat
Heat pump with auxiliary/backup heat
Do you need assistance?
We are here to help.
Call 1-800-468-1502 for wiring
assistance before returning
the thermostat to the store.
This thermostat cannot be used on multistage
systems.
1 69-2714EF—01
M28097
1
Turn Off Power to Heating/
Cooling System
69 -2714EF 01 2
Is there a sealed tube containing
mercury? If so, see back cover for
proper disposal instructions.
M28099
Old thermostat
Cover
Remove old thermostat but leave wallplate with
wires attached.
Remove Old Thermostat
Do not remove
wallplate yet
2
3 69-2714EF—01
Label Wires with Tags
3
Label the wires using the supplied wire labels as you dis-
connect them.
Wire Labels
M28100
M28093
69 -2714EF 01 4
M32731
TO REMOVE WALLPLATE
PULL HERE
Separate Wallplate from
New Thermostat
4
Remove wallplate from the new thermostat and mount onto
wall.
Wallplate
5 69-2714EF—01
Mount the new wallplate using the included screws
and anchors.
5
Mount Wallplate
Drill 3/16-in. holes for drywall
Drill 3/32-in. holes for plaster
W/
Aux
Not
Used
M32714
69 -2714EF 01 6
M32715
SCREW
INSERT WIRES
AND TIGHTEN
SCREWS
WIRE
HOLE
LABELED
WIRES
W/
Aux
W
Y
G
R
Not
Used
Connect Wires
6
Simply match wire labels.
Remove metal jumper if you have both R and Rc wires.
Labels don’t match? See page 22.
Have a Heat Pump system? See page 23-24.
We are here to help.
Call 1-800-468-1502 for wiring assistance.
7 69-2714EF—01
RTHXXXX
M32707
Install two AAA alkaline batteries.
Back of thermostat
7
Install Batteries
69 -2714EF 01 8
Move the switch to the proper setting:
Gas or Oil: For gas or oil heating systems, leave the fan
operation switch in this factory-set position (for systems that
control the fan in a call for heat).
Electric or Heat Pump: Change the switch to this
setting for heat pump or electric heat systems. (This setting
is for systems that allow the thermostat to control the fan in a
call for heat, if a fan wire is connected to the G terminal.)
8
Set fan operation switch
RTHXXXX
M32716
GAS OR OIL
ELECTRIC OR HEAT PUMP
GAS OR OIL
ELECTRIC OR HEAT PUMP
9 69-2714EF—01
W/
Aux
Not
Used
Heat Off Cool Auto On
Fan
M32705
Install thermostat onto the wallplate on the wall.
9
Install Thermostat onto
Wallplate
69 -2714EF 01 10
Turn the power back on to the heating/cooling system.
10
Turn Power Back On
M28098
11 69-2714EF—01
If your system type is:
q Single Stage Heat and Cool
q Heat Only or Cool Only
Congratulations, you’re done!
If your system type is:
q Heat Pump* with Backup Heat
Continue with advanced installation
on next page to match your thermostat to your
system type.
*Heat Pump—an air conditioner that provides cooling in the
summer, and also runs in reverse in the winter to provide
heating.
If you are not sure of your system type or if you
have other questions, call us toll-free at 1-800-
468-1502.
This thermostat works on 24 volt or 750 mV systems. It will
NOT work on multi-stage conventional systems or 120/240
Volt systems.
11
If your system type is...
Advanced Installation
Enter system setup .............................................................. 13
Changing settings ................................................................ 14
System type ......................................................................... 15
Heating cycle rate ................................................................16
Early start ............................................................................17
Temperature display ............................................................18
Compressor protection ........................................................19
Clock display .......................................................................20
Restore program schedule default ......................................21
Wiring conventional system ................................................. 22
Wiring heat pump ................................................................23
Troubleshooting ...................................................................25
Customer assistance ...........................................................26
Limited warranty ..................................................................27
RTHL2510/RTHL2410
13 69-2714EF—01
SETUP WIRING ASSISTANCE TROUBLESHOOTING
Enter System Setup
System setup
To enter system setup, press and hold both the s and
t buttons until the display changes (approximately 5
seconds).
M32713
Heat Off Cool Auto On
Fan
Advanced Installation Guide
69 -2714EF 01 14
SETUPWIRINGASSISTANCETROUBLESHOOTING
1
0
M32717
System setup
Change Function Change Setting
See pages 16–21 to change Function Settings.
Changing Settings
Function Setting
1. Press the s or t button to change the setting.
2. Press the s and t buttons simultaneously for one
second to advance to the next function.
3. Press the Run button to exit and save settings.
NOTE: If you do not press any button for 60 seconds
while you are in the setup menu, the thermostat
automatically saves any changes made and exits the
menu.
RTHL2510/RTHL2410
15 69-2714EF—01
SETUP WIRING ASSISTANCE TROUBLESHOOTING
1
0
M32718
System setup
Function 1: System Type
0 Heating & cooling: Gas, oil or electric heating with
central air conditioning or heat pump without auxiliary/
back-up heat.
1 Heat pump with auxiliary/backup heat:
Outside compressor provides both heating and cooling.
Press the s or t button to select the type of Heat/Cool
system you have in your home.
Press to
change
setting.
When finished,
press s and t
to advance to the
next function.
M32719
AND
OR
Advanced Installation Guide
69 -2714EF 01 16
SETUPWIRINGASSISTANCETROUBLESHOOTING
5
5
M32720
System setup
Press the s or t button to select your heating system
and optimize its operation.
Function 5: Heating cycle rate
5 Gas or oil furnace: Use this setting if you have
a standard gas or oil furnace that is less than 90%
efficient.
6 Electric furnace: Use this setting if you have any
type of electric heating system.
3 Hot water or high-efficiency furnace: Use this
setting if you have a hot water system or a gas furnace
of greater than 90% efficiency.
2 Gas/oil steam or gravity system: Use this
setting if you have a steam or gravity heat system.
Press to
change
setting.
When finished,
press s and t
to advance to the
next function.
M32719
AND
OR
RTHL2510/RTHL2410
17 69-2714EF—01
SETUP WIRING ASSISTANCE TROUBLESHOOTING
13
1
M32721
System setup
Press the s or t button to select Early Start.
Function 13: Early Start
1 On
0 Off
Early start allows the heating or cooling to turn
on before the program start time, so the tem-
perature is reached at the time you set. Simply
program the desired times and temperature
into the schedule. The thermostat will turn the
heating or cooling on early so that the desired
temperature is reached at the desired time.
Press to
change
setting.
When finished,
press s and t
to advance to the
next function.
M32719
AND
OR
Advanced Installation Guide
69 -2714EF 01 18
SETUPWIRINGASSISTANCETROUBLESHOOTING
System setup
Function 14: Temperature display
0 Fahrenheit temperature display (°F)
1 Celsius temperature display (°C)
Press the s or t button to select Fahrenheit or Celsius
temperature display.
14
0
M32722
Press to
change
setting.
When finished,
press s and t
to advance to the
next function.
M32719
AND
OR
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60

Honeywell RTHL2510,RTHL2410 Le manuel du propriétaire

Taper
Le manuel du propriétaire
Ce manuel convient également à

dans d''autres langues