Honeywell RTHL2410 series Le manuel du propriétaire

Marque: Honeywell

Modèle: RTHL2410 series

Catégorie: Thermostats

Taper: Le manuel du propriétaire

Ce manuel convient également à

RTHL2510, RTHL2410

Owner’s Manual

Read and save these

instructions.

For help please visit

yourhome.honeywell.com

RTHL2510/RTHL2410

Series

Programmable

Thermostat

Identify System Type

This thermostat is compatible with the following systems:

• Gas, oil or electric furnace

• Central air conditioner

• Hot water system with or without pump

• Millivolt system

• Central heating and cooling system

• Heat pump without auxiliary/backup heat

• Heat pump with auxiliary/backup heat

Do you need assistance? We are here to help.

Call 1-800-468-1502 for wiring assistance before returning

the thermostat to the store.

This thermostat cannot be used on multistage systems.

NOTICE: To avoid possible compressor damage, do not run air

conditioner if the outside temperature drops below 50°F (10°C).

ATTENTION: MERCURY RECYCLING NOTICE

This product does not contain mercury. However,

this product may replace a product that contains

mercury. Mercury and products containing

mercury should not be discarded in household

trash.

For more information on how and where to

properly recycle a thermostat containing

mercury in the United States, please refer to the

Thermostat Recycling Corporation at

www.thermostat-recycle.org.

For mercury thermostat recycling in Canada,

please refer to Switch the Stat at

www.switchthestat.ca

NO MERCUR

NE PAS JETER

LE MERCURE

RTHXXXX

M32707

Customer assistance

For assistance with this product, please visit

http://yourhome.honeywell.com.

Or call Honeywell Customer Care toll-free at

1-800-468-1502.

To save time, please note your model number

and date code before calling.

Pull at bottom to remove thermostat from

wallplate.

Turn thermostat over to find model number

and date code.

Installation

Installation ............................................3

Advanced Installation ...........................9

About your new thermostat

Controls and Home screen

quick reference ...................................11

Preset energy-saving schedules ........12

Programming and operation

Setting the clock ................................. 12

Adjusting program schedules ............. 13

Overriding schedules temporarily ......14

Overriding schedules permanently ....14

Compressor protection .......................15

Early Start ..........................................15

Replace batteries ...............................16

Appendices

Troubleshooting .................................. 17

Limited warranty ................................. 18

Table of contents

1 Turn Off Power to Heating/Cooling System

M31535

Circuit breaker

box

Heating/cooling system

power switch

Do not remove wallplate yet

3 Label Wires with Tags

Label the wires using the supplied wire labels as you disconnect them.

Wire Labels

M28100

MCR33823

Terminal

designation

If you have an older thermostat with a

sealed mercury tube, turn to page 2

for proper disposal instructions.

Terminal designation

MCR31537

2 Remove Old Thermostat

Remove old thermostat but leave wallplate with wires attached.

4 Separate Wallplate from New Thermostat

Remove wallplate from the new thermostat and mount onto wall.

M32731

TO REMOVE WALLPLATE

PULL HERE

Wallplate

5 Mount Wallplate

Mount the new wallplate using the included screws and anchors.

Drill 3/16-in. holes for drywall

Drill 3/32-in. holes for plaster

6 Connect Wires

Simply match wire labels.

If labels do not match letters on the thermostat, check “Alternate Wiring

(Conventional Systems)” on page 6 and connect to terminal as shown (see

notes, below).

M32715

SCREW

INSERT WIRES

AND TIGHTEN

SCREWS

WIRE

HOLE

LABELED

WIRES

Aux

Not

Used

Remove metal

jumper if you

have both

R and

Rc wires.

We are here to help. Call 1-800-468-1502 for wiring assistance.

Aux

Not

Used

M32714

Alternate Wiring (Conventional Systems)

If labels do not match letters on the thermostat, check the chart below and

connect to terminal as shown here (see notes, below).

If wires will be connected to both R and Rc terminals, remove metal

jumper.

Do not use C or X. Wrap bare end of wire with electrical tape.

If you have a heat pump without auxiliary/backup heat connect O or B,

not both. If you do not have a heat pump, do not connect B. Wrap bare

end of wire with electrical tape.

Place a jumper (piece of wire) between Y and W if you are using a heat

pump without auxiliary/backup heat.

M32727

GW/

AUX

OBY

Aux

Alternate Wiring (Heat Pump)

If labels do not match letters on thermostat, see page 7.

B O G Y

AUX

NOT

USED

R Rc

M32726

7 Install Batteries

Install two AAA alkaline batteries.

Back of thermostat

RTHXXXX

M32707

Alternate wiring (for heat pumps with auxiliary or backup heat only)

If labels do not match letters on the thermostat, check the chart below and

connect to terminal as shown here (see notes, below).

Leave metal jumper in place, connecting R & Rc terminals.

If your old thermostat had both V and VR wires, stop now and contact a

qualified contractor for help.

If your old thermostat had separate O and B wires, wrap the B wire in

electrical tape and do not connect.

If your old thermostat had Y1, W1 and W2 wires, stop now and contact a

qualified contractor for help.

Do not use C or X wire. Do not use B wire if you already have O wire.

Wrap bare end of wire with electrical tape.

Do not use L wire. Wrap bare end of wire with electrical tape.

If your old thermostat had E and Aux wires (or alternate wires), connect both

wires to Aux terminal.

M32728

AUX

B O G Y

AUX

NOT

USED

R Rc

8 Set fan operation switch

Move the switch to the proper setting:

Gas or Oil: For gas or oil heating systems,

leave the fan operation switch in this factory-set

position (for systems that control the fan in a call

for heat).

Electric or Heat Pump: Change the switch

to this setting for heat pump or electric heat

systems. (This setting is for systems that

allow the thermostat to control the fan in a call

for heat, if a fan wire is connected to the G

terminal.)

9 Install Thermostat onto

Wallplate

Install thermostat onto the wallplate on

the wall.

RTHXXXX

M32716

GAS OR OIL

ELECTRIC OR HEAT PUMP

GAS OR OIL

ELECTRIC OR HEAT PUMP

10 Turn Power Back On

Turn the power back on to

the heating/cooling system.

Aux

Not

Used

Heat Off Cool Auto On

Fan

M32705

M31544

Circuit breaker box Heating/cooling system

power switch

11 If your system type is...

If your system type is:

q Single Stage Heat and Cool

q Heat Only or Cool Only

Congratulations, you’re done!

If your system type is:

q Heat Pump* with Backup Heat

Continue with Advanced Installation to match your thermostat to your system

type.

*Heat Pump—an air conditioner that provides cooling in the summer, and also

runs in reverse in the winter to provide heating.

If you are not sure of your system type or if you have other

questions, call us toll-free at 1-800-468-1502.

This thermostat works on 24 volt or 750 mV systems. It will NOT work on multi-

stage conventional systems.

Advanced Installation

Enter System Setup

To enter system setup, press and hold

both the s and t buttons until the display

changes (approximately 5 seconds).

Changing Settings

1. Press the s or t button to change

the setting.

2. Press the s and t buttons

simultaneously for one second to

advance to the next function.

3. Press the RUN button to exit and save

settings.

M32713

Heat Off Cool Auto On

Fan

Function

Setting

M32779

NOTE: If you do not press any button for 60 seconds while you are in the setup

menu, the thermostat automatically saves any changes made and exits the

menu.

Function

Description

Press the s or t button to Setting

1 select system type

0 Heating & cooling: Gas, oil or electric heating with central

air conditioning or heat pump without auxiliary/back-up heat.

1 Heat pump with auxiliary/backup heat: Outside

compressor provides both heating and cooling.

5 select your heating system and

optimize its operation

5 Gas or oil furnace: Use this setting if you have a standard

gas or oil furnace that is less than 90% efﬁcient.

6 Electric furnace: Use this setting if you have any type of

electric heating system.

3 Heat pump, hot water or high-efficiency furnace:

Use this setting if you have a hot water system or a gas

furnace of greater than 90% efﬁciency.

2 Gas/oil steam or gravity system: Use this setting if you

have a steam or gravity heat system.

13 select Early Start

1 On

0 Off

14 select Fahrenheit or Celsius

temperature display

0 Fahrenheit temperature display (°F)

1 Celsius temperature display (°C)

15* select Compressor Protection

settings

1 On

0 Off

20 select clock display

0 12-hour display

1 24-hour display

40 restore program schedule to

default settings

0 Off

1 On: Program schedule default settings are listed on

page12.

* Compressor Protection: This feature forces the compressor to wait approximately 5 minutes before

restarting, to prevent equipment damage. During the wait time, the message “Cool On” or “Heat On”

is displayed on screen.

About your new thermostat

Your new Honeywell thermostat has been designed to give you many years of

reliable service and easy-to-use, push-button climate control.

• Backlit display is easy to read

• Displays ambient (measured) temperature at all times

• One-touch access to setpoint temperature

• Preset program settings

• Temporary and permanent override of schedule

• Early start ensures the right temperature at the right time

• Built-in compressor protection

Thermostat controls

M32700

Heat Off Cool Auto On

Fan

Set: Press to set

time/day/schedule.

Hold: Press

to override

programmed

temperature

control.

Run: Press to

resume program

schedule.

Temperature

adjustment

Press the up or

down buttons

until you reach

the desired

temperature.

NOTE: Make sure

the SYSTEM switch

is set to the system

you want to control

(Heat or Cool).

Fan Switch is used to control your fan.

In “Auto” mode, the fan runs only when

the heating or cooling system is on.

If set to “On,” the fan runs continuously.

System Switch is used to control

your heating or cooling system.

• Heat: Heating system control.

• Off: All systems off.

• Cool: Cooling system control.

Display screen

M32701

Batt

Wake

Set

Heat

Low battery warning

(see page 16)

Setpoint indicator

Appears when the setpoint

temperature is displayed.

Temperature

The ambient (measured)

temperature is normally displayed.

To view the setpoint temperature,

press the Up or Down button

once. The setpoint temperature will

appear for five seconds.

System status

Cool on: Cooling system is on.

Heat on: Heating system is on.

When Cool On is flashing, compressor

protection is engaged (see page 15).

Current day/time

(see page 12)

Current program period

Wake/Leave/Return/Sleep

(see pages 12–14)

Set Time

M32702

Set Day

M32703

Set the time and day

1. Press the SET button, then press

s or t to set the clock time.

2. Press the SET button, then press

s or t to select the day of the

week.

3. Press RUN to save & exit.

NOTE: If the clock flashes, the

thermostat will follow your settings

for the Monday “Wake” time period

until you reset the time and day.

Program Schedule

You can program four time periods each day, with different settings for

weekdays and weekends. We recommend the pre-set settings (shown in the

table below), since they can reduce your heating/cooling expenses.

Wake - Set to the time you

awaken and the temperature you

want during the morning, until

you leave for the day.

Leave - Set to the time you leave

home and the temperature you

want while you are away (usually

an energy-saving level).

Return - Set to the time you

return home and the temperature

you want during the evening,

until bedtime.

Sleep - Set to the time you go to bed and the temperature you want overnight

(usually an energy-saving level).

NOTE: Leave and Return periods can be canceled on weekends.

Heat Cool

Wake

(6:00 am)

Leave

(8:00 am)

Return

(6:00 pm)

Sleep

(10:00 pm)

To adjust program schedules (RTHL2510)

To adjust program schedules (RTHL2410)

1. Press SET until Set Schedule is

displayed.

2. Press s or t to set your weekday

Wake time (Mo-Fr), then press SET.

3. Press s or t to set the

temperature for this time period,

then press SET.

4. Set time and temperature for the

next time period (Leave). Repeat

steps 2 and 3 for each weekday

time period.

5. Press SET to set weekend time

periods (Sa & Su), then press RUN

to save & exit.

NOTE: Make sure the thermostat is set

to the system you want to program

(Heat or Cool).

1. Press SET until Set Schedule is

displayed.

2. Press s or t to set your Wake

time for the day displayed, then

press SET.

3. Press s or t to set the

temperature for this time period,

then press SET.

4. Set time and temperature for the next time

period (Leave). Repeat steps 2 and 3 for

each day’s time period.

5. Press RUN to save & exit.

NOTE: Make sure the thermostat is set to the

system you want to program (Heat or Cool).

Wake

Set Schedule

Set

M32704

Mo Tu We Th Fr

Wake

Set Schedule

Set

M32706

Temporary

Wake

Set

M32708

Set

M32709

Program schedule override (temporary)

Press s or t to immediately adjust

the temperature. This will temporarily

override the temperature setting for

the current time period.

“Temporary” will appear on the display

and the current program period will

flash.

The new temperature will be

maintained only until the next

programmed time period begins (see

page 12).

To cancel the temporary setting at any

time, press RUN.

NOTE: Make sure the thermostat is set

to the system you want to control (heat

or cool).

Hold

Set

M32710

Set

M32709

Program schedule override (permanent)

Press HOLD to permanently adjust

the temperature. This will override

the temperature settings for all time

periods.

The “Hold” feature turns off the

program schedule and allows you to

adjust the thermostat manually, as

needed.

Whatever temperature you set will

be maintained 24 hours a day, until

you manually change it, or press RUN

to cancel “Hold” and resume the

program schedule.

NOTE: Make sure the thermostat is

set to the system you want to control

(heat or cool).

Program schedule override (permanent)

Built-in compressor protection

This feature helps prevent damage to

the compressor in your air conditioning

or heat pump system.

Damage can occur if the compressor is

restarted too soon after shutdown. This

feature forces the compressor to wait 5

minutes before restarting.

During the wait time, the display will

flash the message Cool On (or Heat

On if you have a heat pump). When

the safe wait time has elapsed, the

message stops flashing and the

compressor turns on.

Wake

Cool

M32711

Early Start

This feature allows the heating or

cooling to turn on before the program

start time, so the temperature is

reached at the time you set. For

example: Set the Wake time to 6 am,

and the temperature to 70°. The heat

will come on before 6 am, so the

temperature is 70° by the time you

wake at 6. The next time period is

displayed when the system is activated

before a scheduled time period.

Wake

Cool

M32712

Battery replacement

Install two fresh AAA batteries when

Lo Batt flashes on the screen. Lo

Batt appears for 60 days before the

batteries are depleted.

Replace batteries once a year, or

when you will be away for more than a

month.

Most settings are stored in non-volatile

(permanent) memory. Only the clock

and the day must be set after you

replace the batteries.

Pull at bottom to remove

thermostat from wallplate.

Turn thermostat over,

insert fresh AAA

alkaline batteries, then

reinstall thermostat.

Set the System switch to Off before removing

the batteries. Otherwise, the heating/cooling

system could remain activated even when

batteries are removed.

RTHXXXX

M32707

Aux

Not

Used

Heat Off Cool Auto On

Fan

M32705

Troubleshooting

If you have difficulty with your thermostat, please try the following suggestions.

Most problems can be corrected quickly and easily.

Display is

blank

• Check circuit breaker and reset if necessary.

• Make sure power switch at heating & cooling system is on.

• Make sure furnace door is closed securely.

• Make sure fresh AAA alkaline batteries are correctly

installed.

Heating

or cooling

system does

not respond

• Set system switch to Heat. Make sure the temperature is

set higher than the Inside temperature.

• Set system switch to Cool. Make sure the temperature is

set lower than the Inside temperature.

• Wait 5 minutes for the system to respond.

Temperature

settings do

not change

Make sure heating and cooling temperatures are set to

acceptable ranges:

• Heat: 40° to 90°F (4.5° to 32°C).

• Cool: 50° to 99°F (10° to 37°C).

“Cool On” or

“Heat On” is

flashing

• Compressor protection feature is engaged. Wait 5 minutes

for the system to restart safely, without damage to the

compressor.

“Heat On” is

not displayed

• Set the System switch to Heat, and set the temperature

level above the current room temperature.

“Cool On” is

not displayed

• Set the System switch to Cool, and set the temperature

level below the current room temperature.

For assistance with this product, please visit http://yourhome.honeywell.com or

call Honeywell Customer Care toll-free at 1-800-468-1502.

Automation and Control Solutions

Honeywell International Inc.

1985 Douglas Drive North

Golden Valley, MN 55422

yourhome.honeywell.com

® U.S. Registered Trademark.

33-00126EF—01 M.S. 07-15

Printed in U.S.A.

33-00126EF-01

1-year limited warranty

Honeywell warrants this product, excluding battery, to be free from defects in the

workmanship or materials, under normal use and service, for a period of one (1) year

from the date of purchase by the consumer. If at any time during the warranty period the

product is determined to be defective or malfunctions, Honeywell shall repair or replace it

(at Honeywell’s option).

If the product is defective,

(i) return it, with a bill of sale or other dated proof of purchase, to the place from which

you purchased it; or

(ii) call Honeywell Customer Care at 1-800-468-1502. Customer Care will make the

determination whether the product should be returned to the following address:

Honeywell Return Goods, Dock 4 MN10-3860, 1885 Douglas Dr. N., Golden Valley, MN

55422, or whether a replacement product can be sent to you.

This warranty does not cover removal or reinstallation costs. This warranty shall not apply

if it is shown by Honeywell that the defect or malfunction was caused by damage which

occurred while the product was in the possession of a consumer.

Honeywell’s sole responsibility shall be to repair or replace the product within the terms

stated above. HONEYWELL SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE

OF ANY KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES

RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY,

EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT. Some states

do not allow the exclusion or limitation of incidental or consequential damages, so this

limitation may not apply to you.

THIS WARRANTY IS THE ONLY EXPRESS WARRANTY HONEYWELL MAKES ON

THIS PRODUCT. THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS

HEREBY LIMITED TO THE ONE-YEAR DURATION OF THIS WARRANTY.

Some states do not allow limitations on how long an implied warranty lasts, so the above

limitation may not apply to you. This warranty gives you specific legal rights, and you may

have other rights which vary from state to state.

If you have any questions concerning this warranty, please write Honeywell Customer

Relations, 1985 Douglas Dr, Golden Valley, MN 55422 or call 1-800-468-1502.

RTHL2510/RTHL2410

Série

Veuillez lire le mode

d’emploi et le conserver

en lieu sûr.

Pour obtenir de l’aide

veuillez visiter

yourhome.honeywell.com

Manuel du

propriétaire

Thermostat

programmable

Identifier le type de système

Ce thermostat est compatible avec les systèmes suivants:

• À gaz, mazout ou électrique

• Climatiseur central

• Système à eau chaude avec ou sans pompe

• Système millivolts

• Système de chauffage-refroidissement central

• Thermopompe sans chauffage de secours/auxiliaire

• Thermopompe avec chauffage de secours/auxiliaire

Besoin d’aide? Nous sommes à votre service

Composer le 1-800-468-1502 pour obtenir de l’aide au

raccordement avant de retourner le thermostat au magasin.

Ce thermostat ne peut pas être utilisé sur les systèmes à

plusieurs étages.

AVIS : Pour éviter d’endommager le compresseur, ne faites pas

fonctionner le climatiseur si la température extérieure est inférieure à

10 °C (50 °F).

ATTENTION : AVIS RELATIF AU RECYCLAGE

DU MERCURE

Ce produit ne contient aucun mercure.

Cependant, ce produit peut remplacer un produit

qui contient du mercure. Le mercure et les

produits contenant du mercure ne doivent pas

être jetés aux ordures ménagères.

Pour obtenir plus d›informations pour savoir

comment et où recycler adéquatement un

thermostat contenant du mercure aux États-

Unis, consultez l›organisme de recyclage des

thermostats (Thermostat Recycling Corporation) à

www.thermostat-recycle.org.

Pour le recyclage de thermostats contenant

du mercure au Canada, consultez l›organisme

Switch the Stat à www.switchthestat.ca

NO MERCUR

NE PAS JETER

LE MERCURE

RTHXXXX

M32707

Services à la clientèle

Pour obtenir de l’aide avec ce produit, veuillez

consulter le site

http://yourhome.honeywell.com.

ou vous adresser aux Services à la clientèle de

Honeywell en composant le 1-800-468-1502.

Pour gagner du temps, veuillez prendre en note le

numéro de modèle et de code de date du thermostat

avant d’appeler.

Retourner le thermostat pour trouver le

numéro de modèle et le code de date.

La page charge ...

Honeywell RTHL2410 series Le manuel du propriétaire

Marque: Honeywell

Modèle: RTHL2410 series

Catégorie: Thermostats

Taper: Le manuel du propriétaire

Ce manuel convient également à

RTHL2510, RTHL2410

Télécharger le PDF

rapport

dans d''autres langues

English: Honeywell RTHL2410 series Owner's manual

Honeywell RTHL2410 series Le manuel du propriétaire

Ce manuel convient également à

Honeywell RTHL2410 series Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents