Philips 32PF5420 Le manuel du propriétaire

Marque: Philips

Modèle: 32PF5420

Catégorie: Téléviseurs LCD

Taper: Le manuel du propriétaire

Ce manuel convient également à

32 pf 5420

LCD TV

Information for users in the UK

(Not applicable outside the UK)

Positioning the TV

For the best results, choose a position where light does not fall directly on the screen, and at some

distance away from radiators or other sources of heat. Leave a space of at least 5 cm all around

the TV for ventilation, making sure that curtains, cupboards etc. cannot obstruct the air flow

through the ventilation apertures.

The TV is intended for use in a domestic environment only and should never be operated or

stored in excessively hot or humid atmospheres.

General Points

Please take note of the section 'Tips' at the end of this booklet.

Interference

The Department of Trade and Industry operates a Radio Interference Investigation Service to help

TV license holders improve reception of BBC and IBA programmes where they are being spoilt by

interference.

If your dealer cannot help, ask at a main Post Office for the booklet "How to improve Television

and Radio Reception".

Mains connection

Before connecting the TV to the mains, check that the mains supply voltage corresponds to the

voltage printed on the type plate on the rear panel of the TV. If the mains voltage is different, con-

sult your dealer.

Important

Should it become necessary to replace the mains fuse, this must be replaced with a fuse of the

same value as indicated on the plug.

1. Remove fuse cover and fuse.

2. The replacement fuse must comply with BS 1362 and have the ASTA approval mark.

If the fuse is lost, make contact with your retailer in order to verify the correct type.

3. Refit the fuse cover.

In order to maintain conformity to the EMC directive, the mains plug on this product must not be

removed.

Connecting the aerial

The aerial should be connected to the socket marked x at the back of the set. An inferior aerial is

likely to result in a poor, perhaps unstable picture with ghost images and lack of contrast. Make-

shift or set-top aerials are unlikely to give adequate results.

Your dealer will know from experience the most suitable type for your locality.

Should you wish to use the set in conjunction with other equipment, which connects to the aerial

socket such as TV games, or a video camera, it is recommended that you consult your dealer on

the best method of connection.

Stand (if provided)

Use only the stand provided with the set, making sure that the fixings are properly tightened.A dia-

gram showing how to assemble the stand is packed with the stand. Never use a make-shift stand, or

legs fixed with woodscrews.

info uk 2005 28-01-2005 13:48 Pagina 1

Introduction

Ta b le of Contents

Thank you for purchasing this television set.

This handbook has been designed to help you install and operate your TV set.

We would strongly recommend that you read it thoroughly.

We hope our technology meets entirely with your satisfaction.

Installation

Presentation of the LCD Television . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

The keys on the TV set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Remote control keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Video recorder or DVD keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Installing your television set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Quick installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Program sort . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Manual store . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Other settings in the Install menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Operation

Picture settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Sound adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Feature settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Screen Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Teletext . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Using in PC monitor mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Using in HD (High Definition) Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Peripherals

Video recorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Other equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Side connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Practical information

Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Recycling

The materials used in your set are either reusable or can be recycled.

To minimise environmental waste, specialist companies collect used appliances

and dismantle them after retrieving any materials that can be used again (ask

your dealer for further details).

Presentation of the LCD Television

Remote control

Television keys:

•

POWER: to switch the TV on or off.

•

VOLUME -/+: to adjust sound level.

•

MENU: to access or close menus.

The PROGRAM -/+ keys can be used to select

an adjustment and the VOLUME -/+ keys to

make that adjustment.

•

PROGRAM -/+ (- P +): to select programmes.

Rear of set :

The main connections are made at the bottom

of the television.

For more details on connections see page 12.

é Power socket

“ DVI and audio input for connecting a HD

(high definition) equipment or computer with

DVI output.

‘ EXT1 and EXT2 sockets

( TV aerial socket

§ Side connections

Pull out the plastic insulation sheet from the

battery, this will activate the remote control.

The battery supplied with the appliance does

not contain mercury or nickel cadmium so as to

protect the environment. Please do not discard

your used batteries, but use the recycling

methods available (consult your distributor).

CR 2025

Remote Control Keys for LCD TV Functions

1) . (STANDBY)

To set the TV to standby mode.To switch the TV set on

again, press P –/+, 0 to 9 or AV keys.

x Pixel + (depending on version)

Switches the Pixel + demonstration mode on or off.

· ¢ Ê Æ ∫

Video recorder (page 14)

Q Surround Sound

To activate / deactivate the surround sound effect. In

stereo, this gives the impression that the speakers are

further apart. For models equipped with Virtual Dolby

Surround*, you can experience Dolby Surround Pro

Logic sound effects.

5) AV

To display Source List to select TV or peripheral

equipment connected to EXT1, EXT2/S-VHS2,

AV/S-VHS3, PC or HD (p. 12).

h Active control

Optimizes the picture quality depending on the quality

of the incoming signal and the ambient light conditions.

7) MENU

To call up or exit the TV menus.

8) Cursor (

<>≤≥)

These 4 keys are used to move around the menus.

9) Volume

To adjust the sound level.

10)

ª m Smart picture and sound

Used to access a series of predefined picture and sound

settings.

The personal position relates to settings selected from the

menus.

11)

Ë Screen information

To display / remove the programme number, the time,

the sound mode and the time remaining on the timer.

Hold down for 5 seconds to permanently display the

programme number on the screen.

* Manufactured under license from Dolby Laboratories.“Dolby”

and the double-D symbols are trademarks of Dolby

Laboratories.

10)

11)

Remote Control Keys for LCD TV Functions

12) Mode

Press this key to switch between TV, DVD or AUX.

13)

œ PIP on/off (p. 10)

14)

ı List of programmes

To display / clear the list of programmes. Use the keys

<> to select a programme and the key ≥ to

display it.

15)

∏ Screen Format (p. 8)

16)

ù Sound mode

Used to force programmes in Stereo and Nicam Stereo

to Mono or, for bilingual programmes, to choose

between Dual I or Dual II.

The Mono indication is red when in forced position.

17)

Ÿ Å Ó ¤Teletext (p. 9)

18) Not applicable for TV mode.

19)

[ Mute

To mute or restore the sound.

20) P -/+ Selecting TV programmes

To move up or down a programme.

The number and the

sound

mode are displayed for a few seconds.

For some TV programmes the title of the programme

appears at the bottom of the screen.

21) 0/9 Numerical keys

For direct access to programmes. For a 2 digit

programme number, the 2

digit must be entered

before the dash disappears.

22)

Á Previous programme

To access the previously viewed programme.

The remote control lets you control the main functions of the VCR or DVD.

Press the

MODE key to select the required mode : DVD or AUX (video recorder).The remote control

indicator lights up to display the selected mode. It switches off automatically after 20 seconds if left idle.

The remote control automatically returns to TV mode.

The following keys are operational, depending on the equipment :

. standby,

l¢ fast rewind,

∫l fast forward,

· recording,

∆ pause,

Ê stop,

Æ play,

MENU menu,

<>≤≥ navigation and adjustments,

OK validation,

0/9 digit keys,

P -/+ programme selection,

ù audio selection,

Ë OSD menu,

Á DVD :T-C function / VCR : index

function.

The remote control is compatible with all video

recorders using the RC5 standard and all DVDs

using the RC6 standard.

(12

(13

(14

(15

(16

(17

(18

(19

(20

(21

(22

Video recorder or DVD keys (mode selector)

Quick installation

When you turn on the TV set for the first time,

a menu is displayed on screen.This menu

prompts you to select the country and language

for the menus:

If the menu is not displayed, press the

MENU key

to display the menu.

& Use the

<> keys on the remote control to

select your country and validate with

≥.

If your country does not appear in the list, select

choice “. . .”

é Next select your language using the

<> keys

and validate with

≥.

“ The search starts automatically.All the available

TV programmes and radio stations will be

stored. This operation takes a few minutes.The

display shows the progress of the search and

the number of programs found. At the end of

the search, the menu disappears.

To exit or interrupt the search, press MENU. If no

programme is found, consult the possible solutions p. 14.

‘ If the transmitter or cable network sends the

automatic sort signal, the programs will be

numbered correctly. In this case, the installation

is complete.

( If this is not the case, you need to use the Sort

menu to number the programs correctly.

Some transmitters or cable networks broadcast their

own sort parameters (region, language, etc.). In this

case, indicate your choice using the

<> keys and

validate with

≥.

& Positioning the television set

Place your TV on a solid stable surface. To avoid

danger do not expose the TV to water, or a heat

source (e.g. lamp, candle, radiator). Do not

obstruct the ventilation grid at the rear.

Connecting the aerials

• Use the aerial connection lead supplied and

connect the

: socket situated at the bottom

of the TV to your aerial socket.

• Connect the power lead to the television and the

mains plug into the wall socket (220-240 V/50 Hz).

For connecting other appliances see page p.12.

“

Switching on

To switch on the set, press the POWER key. A

green indicator comes on and the screen lights

up. Go straight to the Quick Installation chapter.

If the TV remains in standby mode(red indicator),

press the

P -/+ key on the remote control.

The indicator will flash when you use the remote control.

Installing your television set

Plug’n’Play

Country

Language

English

Manual store

Other settings in the Install menu

This menu is used to store the programmes

one at a time.

& Press the

MENU key.

é With the cursor, select the Install menu then

Manual store:

“ System: select

Europe (automatic detection*)

Western Europe (BG standard), Eastern

Europe (DK standard), United Kingdom

(I standard) or France (LL’ standard).

* Except for France (LL’ standard), you must select

choice France.

‘ Search: press

≥.The search starts. Once a

programme is found, the scanning stops and its

name is displayed (when available). Go to the

next step. If you know the frequency of the

required programme, this can be entered

directly using the

0 to 9 keys.

If no picture is found, consult the possible solutions (p. 14).

( Program No.: enter the required number

with the

≤≥ or 0 to 9 keys.

§ Fine Tune: if the reception is not satisfactory,

adjust using the ≤≥ keys.

è Store: press

≥.The program is stored.

! Repeat steps ‘ to è for each programme to

store.

ç To quit the menus, press Ë.

& Press the MENU key and select the Install

menu:

é Language: to change the display language for

the menus.

“ Country: to select your country (GB for

Great Britain).

This setting is used for the search, automatic

programme sort and teletext display. If your country

does not appear in the list, select “. . .”

‘ Auto Store: to start automatic search for all

programmes available in your region. If the

transmitter or cable network sends the

automatic sort signal, the programmes will be

numbered correctly. If this is not the case, you

need to use the Sort menu to renumber the

programmes.

Some transmitters or cable networks broadcast

their own sort parameters (region, language, etc.). In

this case, indicate your choice using the

<> keys

and validate with ≥.To quit or interrupt the search,

press MENU. If no picture is found, consult the

possible solutions (p. 14).

( Name:

If required, you can give a name to the

programmes and external connectors. Use the

≤≥ keys to move around the name display area

(5 characters) and the

<> keys to select the

characters.When the name has been entered,

use the

≤ key to exit.The name is stored.

Note: on installation, the programs are named

automatically when an identification signal is sent.

§ To quit the menus, press

Ë.

TV Menu

Picture

Sound

Features

Install

Manual Store

System

Program No.

Fine Tune

Store

Europe

Program sort

& Press the MENU key. The TV Menu is

displayed on the screen.

é With the cursor, select the Install menu

followed by the Sort menu.

“ Select the programme you want to move using

the

<> keys and press ≥.

‘ Then use the

<> keys to select the new

number and validate with

≤.

( Repeat steps “ and ‘ for each program you

wish to renumber.

§ To quit the menus, press

Ë.

TV Menu

Picture

Sound

Features

Install

Language Æ •

Country Æ •

Auto Store Æ •

Manual Store Æ •

Sort Æ •

Name Æ •

Picture settings

Sound adjustments

& Press MENU then ≥.The Picture menu is

displayed:

é Use the

<> keys to select a setting and the

≤≥ keys to adjust.

“ Once the adjustments have been made, select

Store and press ≥ to store them. Press Ë

to exit.

Description of the adjustments:

• Brightness: this changes picture brilliance.

• Colour: this changes the intensity of the colour.

• Contrast: this changes the difference

between the light and dark tones.

•

Sharpness: this changes the picture definition.

• Colour Temp.: this changes the colour

rendering:

Cold (bluer), Normal (balanced)

Warm (redder).

• Store: to store the picture adjustments and

settings.

& Press MENU, select Sound (>) and press ≥.

The

Sound menu is displayed:

é Use the

<> keys to select a setting and the

≤≥ keys to adjust.

“ Once the adjustments have been made, select

Store and press

≥ to store these changes.

‘ To quit the menus, press

Ë.

Description of the settings:

• Equalizer: to adjust the sound tone (from

bass: 120 Hz to treble: 10 kHz).

• Balance: this balances the sound on the left

and right speakers.

• Delta Volume: this is used to compensate

any volume discrepancies between the

different programs or EXT sockets.This

setting is available for programs 0 to 40 and

the EXT sockets.

• AVL (Automatic Volume Leveller): this is

used to limit increases in sound, especially on

program change or advertising slots.

• Dolby Virtual:To activate / deactivate the

surround sound effect.You can also access

these settings with key Q.

• Store: this is used to store the sound settings.

Feature settings

& Press MENU, select Features (>) and

press

≥.You can adjust:

é Contrast +: automatic adjustment of the

picture contrast which permanently sets the

darkest part of the picture to black.

“ NR: attenuates picture noise (snow) in difficult

reception conditions.

‘ Sleep (Only available on certain versions): to

select an automatic standby period.

( PIP: to adjust the size and position of the PIP

screen.

§ To quit the menus, press

Ë.

TV Menu

Picture

Sound

Features

Install

Picture

Brightness

Colour

Contrast

Sharpness

Colour Temp.

Store

TV Menu

Picture

Sound

Features

Install

Sound

Equalizer Æ •

Balance Æ •

Delta Volume Æ •

AVL Æ •

Dolby Virtual Æ •

Store Æ •

120 Hz

500 Hz

1500 Hz

5 KHz

10 KHz

Screen Formats

The pictures you receive may be transmitted in 16:9 format (wide screen) or 4:3 format

(conventional screen). 4:3 pictures sometimes have a black band at the top and bottom of the screen

(letterbox format).This function allows you to optimise the picture display on screen.

Press the

∏

key (or ≤≥) to select the different modes:

This TV set is also equipped with automatic switching which will select the correct-screen

format, provided the specific signals are transmitted with the programmes.

4:3

The picture is reproduced in 4:3 format and a black band is displayed on either side

of the picture.

Movie Expand 14:9

The picture is enlarged to 14:9 format, a thin black band remains on both sides of

the picture.

Movie Expand 16:9

The picture is enlarged to 16:9 format.This mode is recommended when displaying

pictures which have black bands at the top and bottom (letterbox format).

Subtitle Zoom

This mode is used to display 4:3 pictures using the full surface of the screen leaving

the sub-titles visible.

Superzoom

This mode is used to display 4:3 pictures using the full surface of the screen by

enlarging the sides of the picture.

Widescreen

This mode restores the correct proportions of images transmitted in 16:9.

Note:

If you display a 4:3 picture in this mode, it will be enlarged horizontally.

Teletext

Press :

You will obtain :

Teletext is an information system broadcast by certain channels which can be consulted like a

newspaper. It also offers access to subtitles for viewers with hearing problems or who are not familiar

with the transmission language (cable networks, satellite channels, etc.).

Teletext call

Selecting a

page

This is used to call or exit teletext mode.The summary

appears with a list of items that can be accessed. Each

item has a corresponding

3 digit page number.

If the channel selected does not broadcast teletext, the

indication 100 will be displayed and the screen will remain

blank (in this case, exit teletext and select another channel).

Enter the number of the page required using the 0 to 9

or P -/+ keys. Example: page 120, enter 120.

The number is displayed top left, the counter turns and

then the page is displayed. Repeat this operation to view

another page.

If the counter continues to search, this means that the page is

not transmitted. Select another number.

Direct access

to the items

Coloured areas are displayed at the bottom of the screen.

The 4 coloured keys are used to access the items or

corresponding pages.

The coloured areas flash when the item or the page is not yet

available.

Contents

This returns you to the contents page (usually page 100).

Stop

sub-page

acquisition

Double page

teletext

Certain pages contain sub-pages which are automatically

displayed successively.This key is used to stop or resume

sub-page acquisition.The indication

_ appears top left.

To activate or deactivate the double page teletext display

mode.The active pa

ge is di

splayed on the left and the

following page is displayed on the right. Press

if you want

to hold a page (i.e. the contents page).The active page is then

displayed on the right.To return to normal mode, press

Hidden

information

Enlarge a

page

Favourite

pages

To display or hide the concealed information (games

solutions).

This allows you to display the top or bottom part of the

page and then return to normal size.

Instead of the standard coloured areas displayed at the bottom of

the screen, you can store 4 favourite pages on the first

40 channels which can then be accessed using the coloured keys

(red, green, yellow, blue). Once set, these favourite pages will

become the default every time teletext is selected.

& Press the MENU key to change to favourite pages mode.

é Display the teletext page that you want to store.

“ Press the coloured key of your choice for 3 seconds.The

page is now stored.

‘ Repeat the operation with the other coloured keys.

( Now when you consult teletext, your favourite pages will

appear in colour at the bottom of the screen.To

temporarily retrieve the standard items, press MENU.

To clear everything, and return the standard items as the

default, press

Ë for 5 seconds.

Using in PC monitor mode

PC Mode

Your TV can be used as a computer monitor.

The PIP function lets you display a

superimposed image to watch the TV channels

at the same time.

The PIP function only works if your PC has a digital

output.

You must first of all connect the computer and

adjust the resolution (see p.13).

Choosing PC mode

& Press the

AV key on the remote control to

display the

Source List.

é Use the cursor </> key to select

PC and

then press the cursor ≥ key to switch the TV

to PC mode (

DVI In).

To return to TV mode, press the AV key, select

TV and validate with ≥ key.

Using PIP

While in PC mode you can call up a window

for TV channels.

Attention

: the PIP feature is only available if a

computer is connected to the DVI In (see p. 13).

& Press the

œ key to display the PIP screen.

The television image is reproduced in a small

superimposed window.

é Subsequent presses of the

œ key changes

the size of the window, switches to dual

screen and turns PIP off.

“ Use the

P –/+ keys to change the programmes

of the PIP screen.

Using the PC menus

Press the

MENU key to access the specific

settings of the PC monitor mode. Use the

cursor to adjust them (the settings are

automatically saved):

• Picture:

Brightness / Contrast : to adjust the

brightness and contrast.

Horizontal / Vertical*: to adjust the

horizontal and vertical placing of the image.

Adjust Colour: to adjust the colours (cold,

normal or warm).

• Audio Selection: to choose the sound

reproduced on the TV (PC or TV).

• Features:

Phase/Clock*: eliminates the horizontal

(

Phase) and vertical (Clock) interfering lines.

Format : to choose between full screen or

native format of the PC screens.

PIP: to adjust the size and position of the

PIP screen.

Auto Adjust*: position is set automatically.

• Reset To Factory Setting: to return to the

factory settings (default settings).

*These adjustments are not available when a

computer is connected to the

DVI In.

NOTE

– When using the LCD TV as a PC monitor, slight diagonal interference lines may be observed when it is

operated under electromagnetic interference environment but will not affect the performance of this product.

– For better performance, good quality VGA cable with good noise isolation filter is recommended.

Using in HD (High Definition) Mode

HD Mode

The HD (High Definition) mode allows you to

enjoy clearer and sharper pictures through the

DVI inputs if you are using a HD

receiver/ equipment that can transmit high

definition programming.

You must first of all connect the HD equipment

(see p.13).

Choosing HD mode

& Press the

AV key on the remote control to

display the

Source List.

é Use the cursor </> key to select

HD and

then press the cursor key to switch the TV to

HD mode.

To return to TV mode, press the

AV key, select

TV and validate with ≥ key.

Using the HD menus

Press the

MENU key to access the specific

settings of the HD mode. Use the cursor to

adjust them (the settings are automatically

saved):

Picture:

• Brightness: this changes picture brilliance.

• Colour: this changes the intensity of the

colour.

• Contrast: this changes the difference

between the light and dark tones.

•

Sharpness: this changes the picture definition.

• Colour Temp.: this changes the colour

rendering:

Cold (bluer), Normal (balanced)

Warm (redder).

• Store: to store the picture adjustments and

settings.

Sound:

• Equalizer: to adjust the sound tone (from

bass: 120 Hz to treble: 10 kHz).

• Balance: this balances the sound on the left

and right speakers.

• Delta Volume: this is used to compensate

any volume discrepancies between the

different programs or EXT sockets.This

setting is available for programs 0 to 40 and

the EXT sockets.

• AVL (Automatic Volume Leveller): this is

used to limit increases in sound, especially on

program change or advertising slots.

• Dolby Virtual:To activate / deactivate the

surround sound effect.You can also access

these settings with key Q.

• Store: this is used to store the sound

settings.

Features:

• S

leep (Only available on certain versions): to

select an automatic standby period.

•

PIP: to adjust the size and position of the

PIP screen.

• Horizontal Shift: to adjust the horizontal

placing of the image.

Connecting peripheral equipment

Carry out the connections shown opposite, using a good quality

euroconnector cable.

If your video recorder does not have a euroconnector socket, the only

connection possible is via the aerial cable.You will therefore need to

tune in your video recorder's test signal and assign it programme

number 0 (refer to manual store, p. 6).

To reproduce the video recorder picture, press

0 key.

Video recorder with decoder

Connect the decoder to the second euroconnector socket of

the video recorder.You will then be able to record scrambled

transmissions.

The television has 2 external sockets situated at the back of the set (EXT1 and EXT2) and sockets on

the side. Press the

AV key on the remote control to display Source List and select TV or peripheral

equipment connected to

EXT1, EXT2/SVHS2, AV/SVHS3, PC or HD.

The EXT1 socket has audio, CVBS/RGB inputs and audio, CVBS outputs.

The EXT2 socket has audio, CVBS/S-VHS inputs and audio, CVBS outputs.

The side connections has audio inputs, CVBS/S-VHS inputs, headphone out.

Video recorder

DVI In

DVI

Audio In

EXT 2 EXT 1

Headphon

Audio In

Video In

S-Video

Satellite receiver, decoder, CDV, games, etc.

Carry out the connections shown opposite.

To optimise picture quality, connect the equipment which

produces the RGB signals (digital decoder, games, etc.) to EXT1,

and the equipment which produces the S-VHS signals (S-VHS and

Hi-8 video recorders, certain DVD drives) to EXT2 and all other

equipment to either EXT1 or EXT2.

To select connected equipment

Press the

AV key to select EXT1, EXT2/S-VHS2 (S-VHS signals

from the EXT2 socket).

Make the connections as shown opposite.

With the

AV key, select AV/S-VHS3.

For a mono set, connect the sound signal to the AUDIO L (or AUDIO R)

input.The sound automatically comes out of the left and right speakers

of the set.

Headphones

When headphones are connected, the sound on the TV set will be

cut.The

VOLUME -/+

keys are used to adjust the volume level.

The headphone impedance must be between 32 and 600 Ohms.

Make the connections as shown opposite.

With the

AV key, select HD.

For more information on using HD mode see page 11.

Other equipment

Side connections

HD equipment

Computer

PC with DVI

Connect the monitor output (DVI) of your computer to the

DVI-I In of the LCD TV. Connect the sound output Audio out of

the computer to the input DVI Audio in of the LCD TV.

PC with VGA

Connect the monitor output (VGA) of your computer via a

VGA/DVI adaptor to the DVI In of the TV. Connect the sound

output Audio out of the computer to the input DVI Audio in of

the LCD TV.

For more information on using PC mode see page 10.

Configure the computer on 1024 x 768, 60 Hz for

optimum resolution.

Here is the list of the different display resolutions available on

your TV:

640 x 480, 60 Hz 800 x 600, 56 Hz 1024 x 768, 60 Hz

640 x 480, 67 Hz 800 x 600, 60 Hz 1024 x 768, 70 Hz

640 x 480, 72 Hz 800 x 600, 72 Hz 1024 x 768, 75 Hz

640 x 480, 75 Hz 800 x 600, 75 Hz

720 x 400, 70 Hz 832 x 624, 75 Hz

Glossary

DVI (Digital Visual Interface):A digital interface

standard created by the Digital Display

Working Group (DDWG) to convert analog

signals into digital signals to accommodate

both analog and digital monitors.

VGA (Video Graphics Array): a common standard

graphics display system for PCs.

RGB signals : These are the three video signals,

Red Green Blue, which make up the picture.

Using these signals improves picture quality.

S-VHS Signals: These are 2 separate Y/C video

signals from the S-VHS and Hi-8 recording

standards.The luminance signals Y (black and

white) and chrominance signals C (colour) are

recorded separately on the tape.This provides

better picture quality than with standard video

(VHS and 8 mm) where the Y/C signals are

combined to provide only one video signal.

NICAM sound: Process by which digital sound

can be transmitted.

System: Television pictures are not broadcast in

the same way in all countries.There are

different standards: BG, DK, I, and L L’.The

System setting (p. 6) is used to select these

different standards.This is not to be confused

with PAL or SECAM colour coding. Pal is used

in most countries in Europe, Secam in France,

Russia and most African countries.The United

States and Japan use a different system called

NTSC.The inputs EXT1 and EXT2 are used to

read NTSC coded recordings.

16:9: Refers to the ration between the length

and height of the screen.Wide screen

televisions have a ration of 16/9, conventional

screen TV sets have a ration of 4/3.

Tips

Poor reception

No picture

No sound

PC and PIP modes

don’t work ?

Remote control

Standby

Cleaning the set

Still no results?

The proximity of mountains or high buildings may be responsible for ghost

pictures, echoing or shadows. In this case, try manually adjusting your picture: see

Fine Tune (p. 6) or modify the orientation of the outside aerial. If you are using an

indoor aerial, reception may be difficult in certain conditions.You can improve

reception by rotating the aerial. If the reception remains poor, you will need to

use an external aerial

Have you connected the aerial socket properly? Have you chosen the right

system? (p. 6). Poorly connected euroconnector cables or aerial sockets are often

the cause of picture or sound problems (sometimes the connectors can become

half disconnected if the TV set is moved or turned). Check all connections.

If on certain channels you receive a picture but no sound,this means that you do not have

the correct TV system.Modify the

System

setting (p. 6).

The amplifier connected to the TV does not deliver any sound? Check that you

have not confused the audio output with the audio input.

Check that you have configured the computer on a compatible display resolution

(see p. 10).

The TV set does not react to the remote control; the indicator on the set no

longer flashes when you use the remote control? Replace the battery.

If the set receives no signal for 15 mins, it automatically goes into standby mode.

To save power, your set is fitted with components that give it a very low power

consumption when in standby mode (less than 1 W).

Only use a clean, soft and lint-free cloth to clean the screen and the casing of your

set. Do not use alcohol-based or solvent-based products.

Disconnect the mains plug of the TV for 30 seconds then reconnect it.

If your TV set breaks down, never attempt to repair it yourself: contact your

dealer's after-sales service.

Introduction

Sommaire

Vous venez d’acquérir ce téléviseur, merci de votre confiance.

Nous vous conseillons de lire attentivement les instructions qui suivent pour

mieux comprendre les possibilités offertes par votre téléviseur.

Nous espérons que notre technologie vous donnera entière satisfaction.

Installation

Présentation du téléviseur LCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Les touches du téléviseur . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Les touches de la télécommande . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Touche magnétoscope ou DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Installation du téléviseur . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Installation rapide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Classement des programmes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Mémorisation manuelle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Autres réglages du menu Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Utilisation

Réglages de l’image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Réglages du son . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Réglage des options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Format 16:9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Télétexte . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Utilisation en mode moniteur PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Utilisation en mode HD (Haute Définition) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Raccordements

Magnétoscope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Autres appareils . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Connexions latérales . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Ordinateur . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Informations pratiques

Conseils . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Glossaire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Directive pour le recyclage

Votre téléviseur utilise des matériaux réutilisables ou qui peuvent être recyclés.

Pour minimiser les déchets dans l'environnement, des entreprises spécialisées

récupèrent les appareils usagés pour les démonter et concentrer les matières

réutilisables (renseignez-vous auprès de votre revendeur).

Présentation du téléviseur LCD

Télécommande

Les touches du téléviseur

•

POWER : pour allumer ou éteindre le

téléviseur.

•

VOLUME -/+ : pour régler le niveau sonore.

• MENU : pour appeler ou quitter les menus.

Les touches

PROGRAM -/+

permettent de

sélectionner

un réglage et les touches

VOLUME -/+ de régler.

•

PROGRAM -/+ : pour sélectionner les

programmes.

Face arrière :

Les raccordements principaux s’effectuent par

le dessous du téléviseur.

Pour plus de détails sur les raccordements, voir

page 12.

é Alimentation

“ Prise DVI et entrée audio pour le raccordement

d’un appareil HD (Haute Définition) ou d’un

ordinateur avec sortie DVI

‘ Prises péritel EXT 1 et EXT 2

( Prise d’antenne TV

§ Connexions latérales

Retirer le film d’isolation de la pile pour activer

la télécommande.

La pile livrée avec l’appareil ne contient ni mercure ni

cadmium nickel, dans un souci de préserver

l’environnement.Veillez à ne pas jeter vos piles usagées

mais à utiliser les moyens de recyclage mis à votre

disposition (consultez votre revendeur). En cas de

remplacement, utiliser une pile de même type.

CR 2025

La page charge ...

Philips 32PF5420 Le manuel du propriétaire

Marque: Philips

Modèle: 32PF5420

Catégorie: Téléviseurs LCD

Taper: Le manuel du propriétaire

Ce manuel convient également à

32 pf 5420

Télécharger le PDF

rapport

dans d''autres langues

English: Philips 32PF5420 Owner's manual
Nederlands: Philips 32PF5420 de handleiding

Philips 32PF5420 Le manuel du propriétaire

Ce manuel convient également à

Philips 32PF5420 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents